When resuming from hibernation (S4, also known as "suspend to disk") on a
VM, we have seen invalid config space, e.g.,
serial 0000:00:16.3: restoring config space at offset 0x14 (was 0x9104e000, writing 0xffffffff)
To help debug problems like this, log the config space being saved before
suspend, similar to the log in pci_restore_config_dword() when resuming.
Link: https://lore.kernel.org/r/20200113060724.19571-1-yu.c.chen@intel.com
[bhelgaas: commit log]
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Len Brown <lenb@kernel.org>
Some PCI bridges implement BARs in addition to bridge windows. For
example, here's a PLX switch:
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI
Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30, NUMA node 0
Memory at 90a00000 (32-bit, non-prefetchable) [size=256K]
Bus: primary=04, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: 90000000-909fffff
Prefetchable memory behind bridge: 0000380000800000-0000380000bfffff
Previously, when the kernel assigned resource addresses (with the
pci=realloc command line parameter, for example) it could clear the struct
resource corresponding to the BAR. When this happened, lspci would report
this BAR as "ignored":
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [size=256K]
This is because the kernel reports a zero start address and zero flags
in the corresponding sysfs resource file and in /proc/bus/pci/devices.
Investigation with 'lspci -x', however, shows the BIOS-assigned address
will still be programmed in the device's BAR registers.
It's clearly a bug that the kernel lost track of the BAR value, but in most
cases, this still won't result in a visible issue because nothing uses the
memory, so nothing is affected. However, when an IOMMU is in use, it will
not reserve this space in the IOVA because the kernel no longer thinks the
range is valid. (See dmar_init_reserved_ranges() for the Intel
implementation of this.)
Without the proper reserved range, a DMA mapping may allocate an IOVA that
matches a bridge BAR, which results in DMA accesses going to the BAR
instead of the intended RAM.
The problem was in pci_assign_unassigned_root_bus_resources(). When any
resource from a bridge device fails to get assigned, the code set the
resource's flags to zero. This makes sense for bridge windows, as they
will be re-enabled later, but for regular BARs, it makes the kernel
permanently lose track of the fact that they decode address space.
Change pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() so they only clear "res->flags"
for bridge *windows*, not bridge BARs.
Fixes: da7822e5ad ("PCI: update bridge resources to get more big ranges when allocating space (again)")
Link: https://lore.kernel.org/r/20200108213208.4612-1-logang@deltatee.com
[bhelgaas: commit log, check for pci_is_bridge()]
Reported-by: Kit Chow <kchow@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
builtin_platform_driver() and MODULE_* are always odd combination.
This file is not compiled as a module by anyone because
CONFIG_PCIE_UNIPHIER is a bool option.
Let's remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove" code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix AFI_PEX2_CTRL reg offset for Tegra30 by moving it from the Tegra20
SoC struct where it erroneously got added. This fixes the AFI_PEX2_CTRL
reg offset being uninitialised subsequently failing to bring up the
third PCIe port.
Fixes: adb2653b3d ("PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct")
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
pm_runtime_get_sync() returns the device's usage counter. This might
be >0 if the device is already powered up or CONFIG_PM is disabled.
Abort probe function on real error only.
Fixes: da76ba5096 ("PCI: tegra: Add power management support")
Link: https://lore.kernel.org/r/20191216111825.28136-1-david.engraf@sysgo.com
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Cc: stable@vger.kernel.org # v4.17+
The Keystone outbound Address Translation Unit (ATU) maps PCI MMIO space in
8 MB windows. When programming the ATU windows, we previously incremented
the starting address by 8, not 8 MB, so all the windows were mapped to the
first 8 MB. Therefore, only 8 MB of MMIO space was accessible.
Update the loop so it increments the starting address by 8 MB, not 8, so
more MMIO space is accessible.
Fixes: e75043ad97 ("PCI: keystone: Cleanup outbound window configuration")
Link: https://lore.kernel.org/r/20191004154811.GA31397@monakov-y.office.kontur-niirs.ru
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable@vger.kernel.org # v4.20+
ks_pcie_stop_link() function does not clear LTSSM_EN_VAL bit so
link training was not triggered more than once after startup.
In configurations where link can be unstable during early boot,
for example, under low temperature, it will never be established.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Cc: stable@vger.kernel.org
The SDM845 has one Gen2 and one Gen3 controller, add support for these.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Use DesignWare helper functions to configure Fast Training
Sequence. Drop the respective code in the driver.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add support to PCIe RC controller on Intel Gateway SoCs.
PCIe controller is based of Synopsys DesignWare PCIe core.
Intel PCIe driver requires Upconfigure support, Fast Training
Sequence and link speed configurations. So adding the respective
helper functions in the PCIe DesignWare framework.
It also programs hardware autonomous speed during speed
configuration so defining it in pci_regs.h.
Also, mark Intel PCIe driver depends on MSI IRQ Domain
as Synopsys DesignWare framework depends on the
PCI_MSI_IRQ_DOMAIN.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
vep_vector_number is actually a 16 bit register which should be read with
ioread16() instead of ioread32().
Fixes: 080b47def5 ("MicroSemi Switchtec management interface driver")
Link: https://lore.kernel.org/r/20200106190337.2428-3-logang@deltatee.com
Reported-by: Doug Meyer <dmeyer@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use dma_set_mask_and_coherent() instead of dma_set_coherent_mask() as the
Switchtec hardware fully supports 64bit addressing and we should set both
the streaming and coherent masks the same.
[logang@deltatee.com: reworked commit message]
Fixes: aff614c633 ("switchtec: Set DMA coherent mask")
Link: https://lore.kernel.org/r/20200106190337.2428-2-logang@deltatee.com
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Building drivers for ATS-aware IOMMUs as modules requires access to
pci_ats_disabled(). Export it as a GPL symbol to get things working.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: John Garry <john.garry@huawei.com> # smmu v3
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Commit d355bb2097 ("PCI/ATS: Remove unnecessary EXPORT_SYMBOL_GPL()")
unexported a bunch of symbols from the PCI core since the only external
users were non-modular IOMMU drivers. Although most of those symbols
can remain private for now, 'pci_{enable,disable_ats()' is required for
the ARM SMMUv3 driver to build as a module, otherwise we get a build
failure as follows:
| ERROR: "pci_enable_ats" [drivers/iommu/arm-smmu-v3.ko] undefined!
| ERROR: "pci_disable_ats" [drivers/iommu/arm-smmu-v3.ko] undefined!
Re-export these two functions so that the ARM SMMUv3 driver can be build
as a module.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: John Garry <john.garry@huawei.com> # smmu v3
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The PLX PEX NTB forwards DMA transactions using Requester IDs that don't
exist as PCI devices. The devfn for a transaction is used as an index into
a lookup table storing the origin of a transaction on the other side of the
bridge.
Alias all possible devfns to the NTB device so that any transaction coming
in is governed by the mappings for the NTB.
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Add a "nr_devfns" parameter to pci_add_dma_alias() so it can be used to
create DMA aliases for a range of devfns.
[bhelgaas: incorporate nr_devfns fix from James, update
quirk_pex_vca_alias() and setup_aliases()]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of possible devfns is 256, but pci_add_dma_alias() allocated a
bitmap of size 255. Fix this off-by-one error.
This fixes commits 338c3149a2 ("PCI: Add support for multiple DMA
aliases") and c663579273 ("PCI: Allocate dma_alias_mask with
bitmap_zalloc()"), but I doubt it was possible to see a problem because
it takes 4 64-bit longs (or 8 32-bit longs) to hold 255 bits, and
bitmap_zalloc() doesn't save the 255-bit size anywhere.
[bhelgaas: commit log, move #define to drivers/pci/pci.h, include loop
limit fix from Qian Cai:
https://lore.kernel.org/r/20191218170004.5297-1-cai@lca.pw]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
On Asus UX434DA (AMD Ryzen7 3700U) and Asus X512DK (AMD Ryzen5 3500U), the
XHCI controller fails to resume from runtime suspend or s2idle, and USB
becomes unusable from that point.
xhci_hcd 0000:03:00.4: Refused to change power state, currently in D3
xhci_hcd 0000:03:00.4: enabling device (0000 -> 0002)
xhci_hcd 0000:03:00.4: WARN: xHC restore state timeout
xhci_hcd 0000:03:00.4: PCI post-resume error -110!
xhci_hcd 0000:03:00.4: HC died; cleaning up
During suspend, a transition to D3cold is attempted, however the affected
platforms do not seem to cut the power to the PCI device when in this
state, so the device stays in D3hot.
Upon resume, the D3hot-to-D0 transition is successful only if the D3 delay
is increased to 20ms. The transition failure does not appear to be
detectable as a CRS condition. Add a PCI quirk to increase the delay on the
affected hardware.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205587
Link: http://lkml.kernel.org/r/CAD8Lp47Vh69gQjROYG69=waJgL7hs1PwnLonL9+27S_TcRhixA@mail.gmail.com
Link: https://lore.kernel.org/r/20191127053836.31624-2-drake@endlessm.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Separate the D3 delay increase functionality out of quirk_radeon_pm() into
its own function so that it can be shared with other quirks, including the
AMD Ryzen XHCI quirk that will be introduced in a followup commit.
Tweak the function name and message to indicate more clearly that the delay
relates to a D3hot-to-D0 transition.
Link: https://lore.kernel.org/r/20191127053836.31624-1-drake@endlessm.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Previously quirk_paxc_bridge() was applied when the iproc driver was
built-in, but not when it was compiled as a module.
This happened because it was under #ifdef CONFIG_PCIE_IPROC_PLATFORM:
PCIE_IPROC_PLATFORM=y causes CONFIG_PCIE_IPROC_PLATFORM to be defined, but
PCIE_IPROC_PLATFORM=m causes CONFIG_PCIE_IPROC_PLATFORM_MODULE to be
defined.
Move quirk_paxc_bridge() to pcie-iproc.c and drop the #ifdef so the quirk
is always applied, whether iproc is built-in or a module.
[bhelgaas: commit log, move to pcie-iproc.c, not pcie-iproc-platform.c]
Link: https://lore.kernel.org/r/20191211174511.89713-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel SkyLake-E was successfully tested for p2pdma transactions spanning
over a host bridge and PCI bridge with IOMMU on. Add it to the whitelist.
Link: https://lore.kernel.org/r/1575669165-31697-1-git-send-email-abaloyan@gigaio.com
Signed-off-by: Armen Baloyan <abaloyan@gigaio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
In the implementation of pci_iov_add_virtfn() the allocated virtfn is
leaked if pci_setup_device() fails. The error handling is not calling
pci_stop_and_remove_bus_device(). Change the goto label to failed2.
Fixes: 156c55325d ("PCI: Check for pci_setup_device() failure in pci_iov_add_virtfn()")
Link: https://lore.kernel.org/r/20191125195255.23740-1-navid.emamdoost@gmail.com
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
Highlights:
- Infrastructure for secure boot on some bare metal Power9 machines. The
firmware support is still in development, so the code here won't actually
activate secure boot on any existing systems.
- A change to xmon (our crash handler / pseudo-debugger) to restrict it to
read-only mode when the kernel is lockdown'ed, otherwise it's trivial to drop
into xmon and modify kernel data, such as the lockdown state.
- Support for KASLR on 32-bit BookE machines (Freescale / NXP).
- Fixes for our flush_icache_range() and __kernel_sync_dicache() (VDSO) to work
with memory ranges >4GB.
- Some reworks of the pseries CMM (Cooperative Memory Management) driver to
make it behave more like other balloon drivers and enable some cleanups of
generic mm code.
- A series of fixes to our hardware breakpoint support to properly handle
unaligned watchpoint addresses.
Plus a bunch of other smaller improvements, fixes and cleanups.
Thanks to:
Alastair D'Silva, Andrew Donnellan, Aneesh Kumar K.V, Anthony Steinhauser,
Cédric Le Goater, Chris Packham, Chris Smart, Christophe Leroy, Christopher M.
Riedl, Christoph Hellwig, Claudio Carvalho, Daniel Axtens, David Hildenbrand,
Deb McLemore, Diana Craciun, Eric Richter, Geert Uytterhoeven, Greg
Kroah-Hartman, Greg Kurz, Gustavo L. F. Walbon, Hari Bathini, Harish, Jason
Yan, Krzysztof Kozlowski, Leonardo Bras, Mathieu Malaterre, Mauro S. M.
Rodrigues, Michal Suchanek, Mimi Zohar, Nathan Chancellor, Nathan Lynch, Nayna
Jain, Nick Desaulniers, Oliver O'Halloran, Qian Cai, Rasmus Villemoes, Ravi
Bangoria, Sam Bobroff, Santosh Sivaraj, Scott Wood, Thomas Huth, Tyrel
Datwyler, Vaibhav Jain, Valentin Longchamp, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=JHzg
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Infrastructure for secure boot on some bare metal Power9 machines.
The firmware support is still in development, so the code here
won't actually activate secure boot on any existing systems.
- A change to xmon (our crash handler / pseudo-debugger) to restrict
it to read-only mode when the kernel is lockdown'ed, otherwise it's
trivial to drop into xmon and modify kernel data, such as the
lockdown state.
- Support for KASLR on 32-bit BookE machines (Freescale / NXP).
- Fixes for our flush_icache_range() and __kernel_sync_dicache()
(VDSO) to work with memory ranges >4GB.
- Some reworks of the pseries CMM (Cooperative Memory Management)
driver to make it behave more like other balloon drivers and enable
some cleanups of generic mm code.
- A series of fixes to our hardware breakpoint support to properly
handle unaligned watchpoint addresses.
Plus a bunch of other smaller improvements, fixes and cleanups.
Thanks to: Alastair D'Silva, Andrew Donnellan, Aneesh Kumar K.V,
Anthony Steinhauser, Cédric Le Goater, Chris Packham, Chris Smart,
Christophe Leroy, Christopher M. Riedl, Christoph Hellwig, Claudio
Carvalho, Daniel Axtens, David Hildenbrand, Deb McLemore, Diana
Craciun, Eric Richter, Geert Uytterhoeven, Greg Kroah-Hartman, Greg
Kurz, Gustavo L. F. Walbon, Hari Bathini, Harish, Jason Yan, Krzysztof
Kozlowski, Leonardo Bras, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michal Suchanek, Mimi Zohar, Nathan Chancellor, Nathan Lynch, Nayna
Jain, Nick Desaulniers, Oliver O'Halloran, Qian Cai, Rasmus Villemoes,
Ravi Bangoria, Sam Bobroff, Santosh Sivaraj, Scott Wood, Thomas Huth,
Tyrel Datwyler, Vaibhav Jain, Valentin Longchamp, YueHaibing"
* tag 'powerpc-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (144 commits)
powerpc/fixmap: fix crash with HIGHMEM
x86/efi: remove unused variables
powerpc: Define arch_is_kernel_initmem_freed() for lockdep
powerpc/prom_init: Use -ffreestanding to avoid a reference to bcmp
powerpc: Avoid clang warnings around setjmp and longjmp
powerpc: Don't add -mabi= flags when building with Clang
powerpc: Fix Kconfig indentation
powerpc/fixmap: don't clear fixmap area in paging_init()
selftests/powerpc: spectre_v2 test must be built 64-bit
powerpc/powernv: Disable native PCIe port management
powerpc/kexec: Move kexec files into a dedicated subdir.
powerpc/32: Split kexec low level code out of misc_32.S
powerpc/sysdev: drop simple gpio
powerpc/83xx: map IMMR with a BAT.
powerpc/32s: automatically allocate BAT in setbat()
powerpc/ioremap: warn on early use of ioremap()
powerpc: Add support for GENERIC_EARLY_IOREMAP
powerpc/fixmap: Use __fix_to_virt() instead of fix_to_virt()
powerpc/8xx: use the fixmapped IMMR in cpm_reset()
powerpc/8xx: add __init to cpm1 init functions
...
- Consolidate DT "dma-ranges" parsing and convert all host drivers to use
shared parsing (Rob Herring)
* remotes/lorenzo/pci/mmio-dma-ranges:
PCI: Make devm_of_pci_get_host_bridge_resources() static
PCI: rcar: Use inbound resources for setup
PCI: iproc: Use inbound resources for setup
PCI: xgene: Use inbound resources for setup
PCI: v3-semi: Use inbound resources for setup
PCI: ftpci100: Use inbound resources for setup
PCI: of: Add inbound resource parsing to helpers
PCI: versatile: Enable COMPILE_TEST
PCI: versatile: Remove usage of PHYS_OFFSET
PCI: versatile: Use pci_parse_request_of_pci_ranges()
PCI: xilinx-nwl: Use pci_parse_request_of_pci_ranges()
PCI: xilinx: Use pci_parse_request_of_pci_ranges()
PCI: xgene: Use pci_parse_request_of_pci_ranges()
PCI: v3-semi: Use pci_parse_request_of_pci_ranges()
PCI: rockchip: Drop storing driver private outbound resource data
PCI: rockchip: Use pci_parse_request_of_pci_ranges()
PCI: mobiveil: Use pci_parse_request_of_pci_ranges()
PCI: mediatek: Use pci_parse_request_of_pci_ranges()
PCI: iproc: Use pci_parse_request_of_pci_ranges()
PCI: faraday: Use pci_parse_request_of_pci_ranges()
PCI: dwc: Use pci_parse_request_of_pci_ranges()
PCI: altera: Use pci_parse_request_of_pci_ranges()
PCI: aardvark: Use pci_parse_request_of_pci_ranges()
PCI: Export pci_parse_request_of_pci_ranges()
resource: Add a resource_list_first_type helper
# Conflicts:
# drivers/pci/controller/pcie-rcar.c
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
* remotes/lorenzo/pci/vmd:
MAINTAINERS: Remove Keith from VMD maintainer
PCI: vmd: Add device id for VMD device 8086:9A0B
PCI: vmd: Add bus 224-255 restriction decode
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin Murphy)
* remotes/lorenzo/pci/rockchip:
PCI: rockchip: Make some regulators non-optional
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual (Yoshihiro
Shimoda)
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro Shimoda)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Fix missing MACCTLR register setting in initialization sequence
PCI: rcar: Recalculate inbound range alignment for each controller entry
PCI: rcar: Move the inbound index check
PCI: rcar: Remove unnecessary header include (../pci.h)
- Fix endpoint driver sign extension problem when shifting page number to
phys_addr_t (Alan Mikhak)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Cast the page number to phys_addr_t
- Refactor Cadence PCIe host controller to use as a library for both host
and endpoint (Tom Joseph)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Move all files to per-device cadence directory
PCI: cadence: Refactor driver to use as a core library
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted before
the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi Pommarel)
- Don't rely on jiffies in Aardvark config access path since interrupts
may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
* remotes/lorenzo/pci/aardvark:
PCI: pci-bridge-emul: Fix big-endian support
PCI: aardvark: Fix big endian support
PCI: aardvark: Don't rely on jiffies while holding spinlock
PCI: aardvark: Fix PCI_EXP_RTCTL register configuration
PCI: aardvark: Wait for endpoint to be ready before training link
PCI: aardvark: Use LTSSM state to build link training flag
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the VFs,
but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and associated
VFs can be enabled independently (Kuppuswamy Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas)
- Hide PRI and PASID state restoration functions used only inside the PCI
core (Bjorn Helgaas)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian)
- Unify ACS quirk implementations (Bjorn Helgaas)
* pci/virtualization:
PCI: Unify ACS quirk desired vs provided checking
PCI: Make ACS quirk implementations more uniform
PCI: Apply Cavium ACS quirk to ThunderX2 and ThunderX3
PCI/IOV: Serialize sysfs sriov_numvfs reads vs writes
PCI: Add DMA alias quirk for Intel VCA NTB
PCI: Fix Intel ACS quirk UPDCR register address
PCI/ATS: Make pci_restore_pri_state(), pci_restore_pasid_state() private
PCI/ATS: Remove unnecessary EXPORT_SYMBOL_GPL()
PCI/ATS: Remove unused PRI and PASID stubs
PCI/ATS: Consolidate ATS declarations in linux/pci-ats.h
PCI/ATS: Cache PRI PRG Response PASID Required bit
PCI/ATS: Cache PASID Capability offset
PCI/ATS: Cache PRI Capability offset
PCI/ATS: Disable PF/VF ATS service independently
PCI/ATS: Handle sharing of PF PASID Capability with all VFs
PCI/ATS: Handle sharing of PF PRI Capability with all VFs
PCI/ATS: Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI
iommu/vt-d: Select PCI_PRI for INTEL_IOMMU_SVM
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we only
did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0) instead
of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
* pci/pm:
PCI/PM: Move pci_dev_wait() definition earlier
PCI/PM: Add missing link delays required by the PCIe spec
PCI/PM: Add pcie_wait_for_link_delay()
PCI/PM: Return error when changing power state from D3cold
PCI/PM: Decode D3cold power state correctly
PCI/PM: Fold __pci_complete_power_transition() into its caller
PCI/PM: Avoid exporting __pci_complete_power_transition()
PCI/PM: Fold __pci_start_power_transition() into its caller
PCI/PM: Use pci_power_up() in pci_set_power_state()
PCI/PM: Move power state update away from pci_power_up()
PCI/PM: Remove unused pci_driver.suspend_late() hook
PCI/PM: Remove unused pci_driver.resume_early() hook
xen-platform: Convert to generic power management
PCI/PM: Simplify pci_set_power_state()
PCI/PM: Expand PM reset messages to mention D3hot (not just D3)
PCI/PM: Apply D2 delay as milliseconds, not microseconds
PCI/PM: Use pci_WARN() to include device information
PCI/PM: Use PCI dev_printk() wrappers for consistency
PCI/PM: Wrap long lines in documentation
PCI/PM: Note that PME can be generated from D0
PCI/PM: Make power management op coding style consistent
PCI/PM: Run resume fixups before disabling wakeup events
PCI/PM: Clear PCIe PME Status even for legacy power management
PCI/PM: Correct pci_pm_thaw_noirq() documentation
PCI/PM: Always return devices to D0 when thawing
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk for
Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
* pci/msi:
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC even
if platform didn't grant control over AER (Olof Johansson)
* pci/aer:
PCI/DPC: Add "pcie_ports=dpc-native" to allow DPC without AER control
PCI/AER: Fix kernel-doc warnings
PCI/AER: Use for_each_set_bit() to simplify code
PCI/AER: Add PoisonTLPBlocked to Uncorrectable error counters
PCI/AER: Save AER Capability for suspend/resume
The only apparent reason for the PCI_MSI_IRQ_DOMAIN architecture
whitelist was that it requires msi.h. Now that msi.h is mandatory in
asm-generic/Kbuild, every arch should have at least the default version,
so remove the whitelist.
Built for all the architectures that play nice with make.cross, but not
boot tested anywhere.
Link: https://lore.kernel.org/r/514e7b040be8ccd69088193aba260da1b89e919c.1571983829.git.michal.simek@xilinx.com
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Waiman Long <longman@redhat.com>
When a driver enables MSI-X, msix_program_entries() reads the MSI-X Vector
Control register for each vector and saves it in desc->masked. Each
register is 32 bits and bit 0 is the actual Mask bit.
When we restored these registers during resume, we previously set the Mask
bit if *any* bit in desc->masked was set instead of when the Mask bit
itself was set:
pci_restore_state
pci_restore_msi_state
__pci_restore_msix_state
for_each_pci_msi_entry
msix_mask_irq(entry, entry->masked) <-- entire u32 word
__pci_msix_desc_mask_irq(desc, flag)
mask_bits = desc->masked & ~PCI_MSIX_ENTRY_CTRL_MASKBIT
if (flag) <-- testing entire u32, not just bit 0
mask_bits |= PCI_MSIX_ENTRY_CTRL_MASKBIT
writel(mask_bits, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL)
This means that after resume, MSI-X vectors were masked when they shouldn't
be, which leads to timeouts like this:
nvme nvme0: I/O 978 QID 3 timeout, completion polled
On resume, set the Mask bit only when the saved Mask bit from suspend was
set.
This should remove the need for 19ea025e1d ("nvme: Add quirk for Kingston
NVME SSD running FW E8FK11.T").
[bhelgaas: commit log, move fix to __pci_msix_desc_mask_irq()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204887
Link: https://lore.kernel.org/r/20191008034238.2503-1-jian-hong@endlessm.com
Fixes: f2440d9acb ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
27e20603c5 ("PCI/MSI: Move D0 check into pci_msi_check_device()")
moved the power state check into pci_msi_check_device(), which was
subsequently renamed to pci_msi_supported(). This didn't change the
behavior, since both callers checked the power state.
However, it doesn't fit the current "pci_msi_supported()" name, which
should return what the device is capable of, independent of the power
state.
Move the power state check back into the callers for readability. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function pci_irq_get_node() is not used by anyone in the tree, so just
delete it.
Link: https://lore.kernel.org/r/20191014100452.GA6699@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
With the recent 59bb47985c ("mm, sl[aou]b: guarantee natural
alignment for kmalloc(power-of-two)"), kzalloc() is able to allocate
a 4KB buffer that is guaranteed to be 4KB-aligned. Here the size and
alignment of hbus is important because hbus's field
retarget_msi_interrupt_params must not cross a 4KB page boundary.
Here we prefer kzalloc to get_zeroed_page(), because a buffer
allocated by the latter is not tracked and scanned by kmemleak, and
hence kmemleak reports the pointer contained in the hbus buffer
(i.e. the hpdev struct, which is created in new_pcichild_device() and
is tracked by hbus->children) as memory leak (false positive).
If the kernel doesn't have 59bb47985c, get_zeroed_page() *must* be
used to allocate the hbus buffer and we can avoid the kmemleak false
positive by using kmemleak_alloc() and kmemleak_free() to ask
kmemleak to track and scan the hbus buffer.
Reported-by: Lili Deng <v-lide@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
A VM can have multiple Hyper-V hbus. It's incorrect to set the global
variable 'pci_protocol_version' when *every* hbus is initialized in
hv_pci_protocol_negotiation(). This is not an issue in practice since
every hbus should have the same value of hbus->protocol_version, but
we should make the variable per-hbus, so in case we have busses
with different protocol versions, the driver can still work correctly.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Add suspend() and resume() functions so that Hyper-V virtual PCI devices
are handled properly when the VM hibernates and resumes from
hibernation.
Note that the suspend() function must make sure there are no pending
work items before calling vmbus_close(), since it runs in a process
context as a callback in dpm_suspend(). When it starts to run, the
channel callback hv_pci_onchannelcallback(), which runs in a tasklet
context, can be still running concurrently and scheduling new work items
onto hbus->wq in hv_pci_devices_present() and hv_pci_eject_device(), and
the work item handlers can access the vmbus channel, which can be being
closed by hv_pci_suspend(), e.g. the work item handler
pci_devices_present_work() -> new_pcichild_device() writes to the vmbus
channel.
To eliminate the race, hv_pci_suspend() disables the channel callback
tasklet, sets hbus->state to hv_pcibus_removing, and re-enables the
tasklet. This way, when hv_pci_suspend() proceeds, it knows that no new
work item can be scheduled, and then it flushes hbus->wq and safely
closes the vmbus channel.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
There is no functional change. This is just preparatory for a later
patch which adds the hibernation support for the pci-hyperv driver.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3bzrQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LkMB/4/MkpN4F2WudNCKgmYay2gw3hq8aOR
5Xh/SE6N3BEgBpQiMEUdePRT6LqnQMsSpOaUoKfd4nFvCyLaV7itaYzQuUpo+UJ/
a4UDHJPVfrDJeFghWqSngfEW/N66mpO3UuAvhSRTR3ku0T31v9FkcLsMbdxVUpLC
ablSaFfPCOtTQOsG9blRUL/GAWUhGzPI/Hl4VldS0FvKDmMDY2fxt7QxXRaEYItc
i1Uthklxd0BfRmDqv0WEpduUhbwzg6Uir9pXSisux7DpMk1Li0IyPST5UcRl0Zf4
CKL/qfdQANpufj9kGmrlCOnXB9P5/XYVwfYV430WqMyw0QaOzzSrxT7C
=CZ/+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, CONFIG_PCIEASPM_DEBUG enabled "link_state" and "clk_ctl" sysfs
files that controlled ASPM. We believe these files were rarely if ever
used.
We recently added sysfs ASPM controls that are always present, so the debug
code is no longer needed. Removing this debug code has been discussed for
quite some time, see e.g. [0].
Remove PCIEASPM_DEBUG and the related code.
[0] https://lore.kernel.org/lkml/20180727202619.GD173328@bhelgaas-glaptop.roam.corp.google.com/
Link: https://lore.kernel.org/r/ec935d8e-c084-3938-f1d1-748617596b25@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to Endpoints and other Upstream Ports to control ASPM,
Clock PM, and L1 PM Substates. The new attributes are:
/sys/devices/pci*/.../link/clkpm
/sys/devices/pci*/.../link/l0s_aspm
/sys/devices/pci*/.../link/l1_aspm
/sys/devices/pci*/.../link/l1_1_aspm
/sys/devices/pci*/.../link/l1_2_aspm
/sys/devices/pci*/.../link/l1_1_pcipm
/sys/devices/pci*/.../link/l1_2_pcipm
An attribute is only visible if both ends of the Link leading to the device
support the state. Writing y/1/on to the file enables the state; n/0/off
disables it.
These attributes can be used to tune the power/performance tradeoff for
individual devices.
[bhelgaas: commit log, rename directory to "link"]
Link: https://lore.kernel.org/r/b1c83f8a-9bf6-eac5-82d0-cf5b90128fbf@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
[bhelgaas: do same in vmd.c]
Link: https://lore.kernel.org/r/20191120134036.14502-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the mode register to host(RC) mode so that the host controller
mode is set-up consistently across SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Some things in drivers/pci/pcie (aspm.c and ptm.c) do not depend on the
PCIe portdrv, so we should be able to build them even if PCIEPORTBUS is not
selected. Remove the PCIEPORTBUS guard from building pcie/.
Link: https://lore.kernel.org/r/20191106222420.10216-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
drivers/pci/pcie/Kconfig is only sourced by drivers/pci/Kconfig, and only
when PCI is defined, so there's no need to depend on PCI again. Remove the
unnecessary dependencies.
Link: https://lore.kernel.org/r/20191106222420.10216-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The PTM support does not depend on the portdrv, so remove the Kconfig
dependency.
Link: https://lore.kernel.org/r/20191106222420.10216-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jonathan Yong <jonathan.yong@intel.com>
The granularity message has an extra "d":
pci 0000:02:00.0: PTM enabled, 4dns granularity
Remove the "d" so the message is simply "PTM enabled, 4ns granularity".
Fixes: 8b2ec318ee ("PCI: Add PTM clock granularity information")
Link: https://lore.kernel.org/r/20191106222420.10216-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jonathan Yong <jonathan.yong@intel.com>
56c1af4606 ("PCI: Add sysfs max_link_speed/width,
current_link_speed/width, etc") added the following objects, but they are
unused, so remove them:
pci_bridge_group
pci_bridge_groups
pcie_dev_group
pcie_dev_groups
This fixes the following warnings from sparse:
drivers/pci/pci-sysfs.c:1546:30: warning: symbol 'pci_bridge_groups' was not declared. Should it be static?
drivers/pci/pci-sysfs.c:1555:30: warning: symbol 'pcie_dev_groups' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20191016080324.12864-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Change:
drivers/pci/controller/pcie-cadence.h
drivers/pci/controller/pcie-rockchip.h
to use the correct SPDX comment style per section 2 of
Documentation/process/license-rules.rst.
These resolve the following checkpatch.pl warning:
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20190828135322.10370-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the definition of pci_dev_wait() above pci_power_up() so that it can
be called from the latter with no change in functionality. This is a pure
code move with no functional change.
Link: https://lore.kernel.org/r/20191120051743.23124-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain🚌dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in
c2bf1fc212 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
Link: https://lore.kernel.org/r/20191112091617.70282-3-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_wait_for_link_delay(). Similar to pcie_wait_for_link() but allows
passing custom activation delay in milliseconds.
Link: https://lore.kernel.org/r/20191112091617.70282-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_raw_set_power_state() uses the Power Management capability to change a
device's power state. The capability is in config space, which is
accessible in D0, D1, D2, and D3hot, but not in D3cold.
If we call pci_raw_set_power_state() on a device that's in D3cold, config
reads fail and return ~0 data, which we erroneously interpreted as "the
device is in D3hot", leading to messages like this:
pcieport 0000:03:00.0: Refused to change power state, currently in D3
The PCI_PM_CTRL has several RsvdP fields, so ~0 is never a valid register
value. If we get that value, print a more informative message and return
an error.
Changing the power state of a device from D3cold must be done by a platform
power management method or some other non-config space mechanism.
Link: https://lore.kernel.org/r/20190822200551.129039-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use pci_power_name() to print pci_power_t correctly. This changes:
"state 0" or "D0" to "D0"
"state 1" or "D1" to "D1"
"state 2" or "D2" to "D2"
"state 3" or "D3" to "D3hot"
"state 4" or "D4" to "D3cold"
Changes dmesg logging only, no other functional change intended.
Link: https://lore.kernel.org/r/20190822200551.129039-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Because pci_set_power_state() has become the only caller of
__pci_complete_power_transition(), there is no need for the latter to
be a separate function any more, so fold it into the former, drop a
redundant check and reduce the number of lines of code somewhat.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/15576968.k611qn3UU0@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Notice that radeon_set_suspend(), which is the only caller of
__pci_complete_power_transition() outside of pci.c, really only
cares about the pci_platform_power_transition() invoked by it,
so export the latter instead of it, update the radeon driver to
call pci_platform_power_transition() directly and make
__pci_complete_power_transition() static.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/1731661.ykamz2Tiuf@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Because pci_power_up() has become the only caller of
__pci_start_power_transition(), there is no need for the latter to
be a separate function any more, so fold it into the former, drop a
redundant check and reduce the number of lines of code somewhat.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/3458080.lsoDbfkST9@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make it explicitly clear that the code to put devices into D0 in
pci_set_power_state() and in pci_pm_default_resume_early() is the
same by making the latter use pci_power_up() for transitions into D0.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/2520019.OZ1nXS5aSj@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move the invocation of pci_update_current_state() from pci_power_up() to
pci_pm_default_resume_early(), which is the only caller of that function.
Preparatory change, no functional impact.
Link: https://lore.kernel.org/r/37482337.udjOGdOKNb@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The struct pci_driver.suspend_late() hook is one of the legacy PCI power
management callbacks, and there are no remaining users of it. Remove it.
Link: https://lore.kernel.org/r/20191101204558.210235-7-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The struct pci_driver.resume_early() hook is one of the legacy PCI power
management callbacks, and there are no remaining users of it. Remove it.
Link: https://lore.kernel.org/r/20191101204558.210235-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check for the PCI_DEV_FLAGS_NO_D3 quirk early, before calling
__pci_start_power_transition(). This way all the cases where we don't need
to do anything at all are checked up front.
This doesn't fix anything because if the caller requested D3hot or D3cold,
__pci_start_power_transition() is a no-op. But calling it is pointless and
makes the code harder to analyze.
Link: https://lore.kernel.org/r/20191101204558.210235-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_reset() resets a device by putting it in D3hot and bringing it back
to D0. Clarify related messages to mention "D3hot" explicitly instead of
just "D3".
Link: https://lore.kernel.org/r/20191101204558.210235-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCI_PM_D2_DELAY is defined as 200, which is milliseconds, but previously we
used udelay(), which only waited for 200 microseconds. Use msleep()
instead so we wait the correct amount of time. See PCIe r5.0, sec 5.9.
Link: https://lore.kernel.org/r/20191101204558.210235-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the PCI dev_printk() wrappers for consistency with the rest of the PCI
core. No functional change intended.
Link: https://lore.kernel.org/r/20191017212851.54237-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some of the power management ops use this style:
struct device_driver *drv = dev->driver;
if (drv && drv->pm && drv->pm->prepare(dev))
drv->pm->prepare(dev);
while others use this:
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
if (pm && pm->runtime_resume)
pm->runtime_resume(dev);
Convert the first style to the second so they're all consistent. Remove
local "error" variables when unnecessary. No functional change intended.
Link: https://lore.kernel.org/r/20191014230016.240912-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_resume() and pci_pm_restore() call pci_pm_default_resume(), which
runs resume fixups before disabling wakeup events:
static void pci_pm_default_resume(struct pci_dev *pci_dev)
{
pci_fixup_device(pci_fixup_resume, pci_dev);
pci_enable_wake(pci_dev, PCI_D0, false);
}
pci_pm_runtime_resume() does both of these, but in the opposite order:
pci_enable_wake(pci_dev, PCI_D0, false);
pci_fixup_device(pci_fixup_resume, pci_dev);
We should always use the same ordering unless there's a reason to do
otherwise. Change pci_pm_runtime_resume() to call pci_pm_default_resume()
instead of open-coding this, so the fixups are always done before disabling
wakeup events.
pci_pm_default_resume() is called from pci_pm_runtime_resume(), which is
under #ifdef CONFIG_PM. If SUSPEND and HIBERNATION are disabled, PM_SLEEP
is disabled also, so move pci_pm_default_resume() from #ifdef
CONFIG_PM_SLEEP to #ifdef CONFIG_PM.
Link: https://lore.kernel.org/r/20191014230016.240912-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, pci_pm_resume_noirq() cleared the PME Status bit in the Root
Status register only if the device had no driver or the driver did not
implement legacy power management. It should clear PME Status regardless
of what sort of power management the driver supports, so do this before
checking for legacy power management.
This affects Root Ports and Root Complex Event Collectors, for which the
usual driver is the PCIe portdrv, which implements new power management, so
this change is just on principle, not to fix any actual defects.
Fixes: a39bd851dc ("PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver")
Link: https://lore.kernel.org/r/20191014230016.240912-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_thaw_noirq() is supposed to return the device to D0 and restore its
configuration registers, but previously it only did that for devices whose
drivers implemented the new power management ops.
Hibernation, e.g., via "echo disk > /sys/power/state", involves freezing
devices, creating a hibernation image, thawing devices, writing the image,
and powering off. The fact that thawing did not return devices with legacy
power management to D0 caused errors, e.g., in this path:
pci_pm_thaw_noirq
if (pci_has_legacy_pm_support(pci_dev)) # true for Mellanox VF driver
return pci_legacy_resume_early(dev) # ... legacy PM skips the rest
pci_set_power_state(pci_dev, PCI_D0)
pci_restore_state(pci_dev)
pci_pm_thaw
if (pci_has_legacy_pm_support(pci_dev))
pci_legacy_resume
drv->resume
mlx4_resume
...
pci_enable_msix_range
...
if (dev->current_state != PCI_D0) # <---
return -EINVAL;
which caused these warnings:
mlx4_core a6d1:00:02.0: INTx is not supported in multi-function mode, aborting
PM: dpm_run_callback(): pci_pm_thaw+0x0/0xd7 returns -95
PM: Device a6d1:00:02.0 failed to thaw: error -95
Return devices to D0 and restore config registers for all devices, not just
those whose drivers support new power management.
[bhelgaas: also call pci_restore_state() before pci_legacy_resume_early(),
update comment, add stable tag, commit log]
Link: https://lore.kernel.org/r/KU1P153MB016637CAEAD346F0AA8E3801BFAD0@KU1P153MB0166.APCP153.PROD.OUTLOOK.COM
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v4.13+
The 0V9 and 1V8 supplies power the PCIe block in the SoC itself, and
are thus fundamental to PCIe being usable at all. As such, it makes
sense to treat them as non-optional and rely on dummy regulators if
not explicitly described.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Now that all the PCI host drivers are using pci_parse_request_of_pci_ranges(),
make devm_of_pci_get_host_bridge_resources() static.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Renesas R-Car PCIe host bridge to
use the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Broadcom iProc host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert the Xgene host bridge to use the
resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert the v3-semi host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Faraday ftpci100 host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Extend devm_of_pci_get_host_bridge_resources() and
pci_parse_request_of_pci_ranges() helpers to also parse the inbound
addresses from DT 'dma-ranges' and populate a resource list with the
translated addresses. This will help ensure 'dma-ranges' is always
parsed in a consistent way.
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> # for AArdvark
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: rfi@lists.rocketboards.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
This patch adds support for this VMD device which supports the bus
restriction mode.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VMD bus restrictions are required when IO fabric is multiplexed such
that VMD cannot use the entire bus range. This patch adds another bus
restriction decode bit that can be set by firmware to restrict the VMD
bus range to between 224-255.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Most of the ACS quirks have a similar pattern of:
acs_flags &= ~( <controls provided by this device> );
return acs_flags ? 0 : 1;
Pull this out into a helper function to simplify the quirks slightly. The
helper function is also a convenient place for comments about what the list
of ACS controls means. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
The ACS quirks differ in needless ways, which makes them look more
different than they really are.
Reorder the ACS flags in order of definitions in the spec:
PCI_ACS_SV Source Validation
PCI_ACS_TB Translation Blocking
PCI_ACS_RR P2P Request Redirect
PCI_ACS_CR P2P Completion Redirect
PCI_ACS_UF Upstream Forwarding
PCI_ACS_EC P2P Egress Control
PCI_ACS_DT Direct Translated P2P
(PCIe r5.0, sec 7.7.8.2) and use similar code structure in all. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
As per PCIe r5.0, sec 7.8.5.2, fixed bus numbers of a bridge must be zero
when no function that uses EA is located behind it. Hence, if EA supplies
bus numbers of zero, assign bus numbers normally. A secondary bus can
never have a bus number of zero, so setting a bridge's Secondary Bus Number
to zero makes downstream devices unreachable.
[bhelgaas: retain bool return value so "zero is invalid" logic is local]
Fixes: 2dbce59011 ("PCI: Assign bus numbers present in EA capability for bridges")
Link: https://lore.kernel.org/r/1572850664-9861-1-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.2+
Previously, the kernel sometimes assigned more MMIO or MMIO_PREF space than
desired. For example, if the user requested 128M of space with
"pci=realloc,hpmemsize=128M", we sometimes assigned 256M:
pci 0000:06:01.0: BAR 14: assigned [mem 0x90100000-0xa00fffff] = 256M
pci 0000:06:04.0: BAR 14: assigned [mem 0xa0200000-0xb01fffff] = 256M
With this patch applied:
pci 0000:06:01.0: BAR 14: assigned [mem 0x90100000-0x980fffff] = 128M
pci 0000:06:04.0: BAR 14: assigned [mem 0x98200000-0xa01fffff] = 128M
This happened when in the first pass, the MMIO_PREF succeeded but the MMIO
failed. In the next pass, because MMIO_PREF was already assigned, the
attempt to assign MMIO_PREF returned an error code instead of success
(nothing more to do, already allocated). Hence, the size which was actually
allocated, but thought to have failed, was placed in the MMIO window.
The bug resulted in the MMIO_PREF being added to the MMIO window, which
meant doubling if MMIO_PREF size = MMIO size. With a large MMIO_PREF, the
MMIO window would likely fail to be assigned altogether due to lack of
32-bit address space.
Change find_free_bus_resource() to do the following:
- Return first unassigned resource of the correct type.
- If there is none, return first assigned resource of the correct type.
- If none of the above, return NULL.
Returning an assigned resource of the correct type allows the caller to
distinguish between already assigned and no resource of the correct type.
Add checks in pbus_size_io() and pbus_size_mem() to return success if
resource returned from find_free_bus_resource() is already allocated.
This avoids pbus_size_io() and pbus_size_mem() returning error code to
__pci_bus_size_bridges() when a resource has been successfully assigned in
a previous pass. This fixes the existing behaviour where space for a
resource could be reserved multiple times in different parent bridge
windows.
Link: https://lore.kernel.org/lkml/20190531171216.20532-2-logang@deltatee.com/T/#u
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203243
Link: https://lore.kernel.org/r/PS2P216MB075563AA6AD242AA666EDC6A80760@PS2P216MB0755.KORP216.PROD.OUTLOOK.COM
Reported-by: Kit Chow <kchow@gigaio.com>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Valerio and others reported that commit 84c8b58ed3 ("ACPI / hotplug /
PCI: Don't scan bridges managed by native hotplug") prevents some recent
LG and HP laptops from booting with endless loop of:
ACPI Error: No handler or method for GPE 08, disabling event (20190215/evgpe-835)
ACPI Error: No handler or method for GPE 09, disabling event (20190215/evgpe-835)
ACPI Error: No handler or method for GPE 0A, disabling event (20190215/evgpe-835)
...
What seems to happen is that during boot, after the initial PCI enumeration
when EC is enabled the platform triggers ACPI Notify() to one of the root
ports. The root port itself looks like this:
pci 0000:00:1b.0: PCI bridge to [bus 02-3a]
pci 0000:00:1b.0: bridge window [mem 0xc4000000-0xda0fffff]
pci 0000:00:1b.0: bridge window [mem 0x80000000-0xa1ffffff 64bit pref]
The BIOS has configured the root port so that it does not have I/O bridge
window.
Now when the ACPI Notify() is triggered ACPI hotplug handler calls
acpiphp_native_scan_bridge() for each non-hotplug bridge (as this system is
using native PCIe hotplug) and pci_assign_unassigned_bridge_resources() to
allocate resources.
The device connected to the root port is a PCIe switch (Thunderbolt
controller) with two hotplug downstream ports. Because of the hotplug ports
__pci_bus_size_bridges() tries to add "additional I/O" of 256 bytes to each
(DEFAULT_HOTPLUG_IO_SIZE). This gets further aligned to 4k as that's the
minimum I/O window size so each hotplug port gets 4k I/O window and the
same happens for the root port (which is also hotplug port). This means
3 * 4k = 12k I/O window.
Because of this pci_assign_unassigned_bridge_resources() ends up opening a
I/O bridge window for the root port at first available I/O address which
seems to be in range 0x1000 - 0x3fff. Normally this range is used for ACPI
stuff such as GPE bits (below is part of /proc/ioports):
1800-1803 : ACPI PM1a_EVT_BLK
1804-1805 : ACPI PM1a_CNT_BLK
1808-180b : ACPI PM_TMR
1810-1815 : ACPI CPU throttle
1850-1850 : ACPI PM2_CNT_BLK
1854-1857 : pnp 00:05
1860-187f : ACPI GPE0_BLK
However, when the ACPI Notify() happened this range was not yet reserved
for ACPI/PNP (that happens later) so PCI gets it. It then starts writing to
this range and accidentally stomps over GPE bits among other things causing
the endless stream of messages about missing GPE handler.
This problem does not happen if "pci=hpiosize=0" is passed in the kernel
command line. The reason is that then the kernel does not try to allocate
the additional 256 bytes for each hotplug port.
Fix this by allocating resources directly below the non-hotplug bridges
where a new device may appear as a result of ACPI Notify(). This avoids the
hotplug bridges and prevents opening the additional I/O window.
Fixes: 84c8b58ed3 ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203617
Link: https://lore.kernel.org/r/20191030150545.19885-1-mika.westerberg@linux.intel.com
Reported-by: Valerio Passini <passini.valerio@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
The newer ibm,drc-info property is a condensed description of the old
ibm,drc-* properties (ie. names, types, indexes, and power-domains).
When matching a drc-index to a drc-name we need to verify that the
index is within the start and last drc-index range and map it to a
drc-name using the drc-name-prefix and logical index.
Fix the mapping by checking that the index is within the range of the
current drc-info entry, and build the name from the drc-name-prefix
concatenated with the starting drc-name-suffix value and the sequential
index obtained by subtracting ibm,my-drc-index from this entries
drc-start-index.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-10-git-send-email-tyreld@linux.ibm.com
The device tree is in big endian format and any properties directly
retrieved using OF helpers that don't explicitly byte swap should
be annotated. In particular there are several places where we grab
the opaque property value for the old ibm,drc-* properties and the
ibm,my-drc-index property.
Fix this for better static checking by annotating values we know to
explicitly big endian, and byte swap where appropriate.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-9-git-send-email-tyreld@linux.ibm.com
Split physical PCI slot registration scanning into separate routines
that support the old ibm,drc-* properties and one that supports the
new compressed ibm,drc-info property.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-7-git-send-email-tyreld@linux.ibm.com
In the event that the partition is migrated to a platform with older
firmware that doesn't support the ibm,drc-info property the device
tree is modified to remove the ibm,drc-info property and replace it
with the older style ibm,drc-* properties for types, names, indexes,
and power-domains. One of the requirements of the drc-info firmware
feature is that the client is able to handle both the new property,
and old style properties at runtime. Therefore we can't rely on the
firmware feature alone to dictate which property is currently
present in the device tree.
Fix this short coming by checking explicitly for the ibm,drc-info
property, and falling back to the older ibm,drc-* properties if it
doesn't exist.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-6-git-send-email-tyreld@linux.ibm.com
The first entry of the ibm,drc-info property is an int encoded count
of the number of drc-info entries that follow. The "value" pointer
returned by of_prop_next_u32() is still pointing at the this value
when we call of_read_drc_info_cell(), but the helper function
expects that value to be pointing at the first element of an entry.
Fix up by incrementing the "value" pointer to point at the first
element of the first drc-info entry prior.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-5-git-send-email-tyreld@linux.ibm.com
This addresses deadlocks in these common cases in hierarchies containing
two switches:
- All involved ports are runtime suspended and they are unplugged. This
can happen easily if the drivers involved automatically enable runtime
PM (xHCI for example does that).
- System is suspended (e.g., closing the lid on a laptop) with a dock +
something else connected, and the dock is unplugged while suspended.
These cases lead to the following deadlock:
INFO: task irq/126-pciehp:198 blocked for more than 120 seconds.
irq/126-pciehp D 0 198 2 0x80000000
Call Trace:
schedule+0x2c/0x80
schedule_timeout+0x246/0x350
wait_for_completion+0xb7/0x140
kthread_stop+0x49/0x110
free_irq+0x32/0x70
pcie_shutdown_notification+0x2f/0x50
pciehp_remove+0x27/0x50
pcie_port_remove_service+0x36/0x50
device_release_driver+0x12/0x20
bus_remove_device+0xec/0x160
device_del+0x13b/0x350
device_unregister+0x1a/0x60
remove_iter+0x1e/0x30
device_for_each_child+0x56/0x90
pcie_port_device_remove+0x22/0x40
pcie_portdrv_remove+0x20/0x60
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0x18c/0x250
device_release_driver+0x12/0x20
pci_stop_bus_device+0x6f/0x90
pci_stop_bus_device+0x31/0x90
pci_stop_and_remove_bus_device+0x12/0x20
pciehp_unconfigure_device+0x88/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
INFO: task irq/190-pciehp:2288 blocked for more than 120 seconds.
irq/190-pciehp D 0 2288 2 0x80000000
Call Trace:
__schedule+0x2a2/0x880
schedule+0x2c/0x80
schedule_preempt_disabled+0xe/0x10
mutex_lock+0x2c/0x30
pci_lock_rescan_remove+0x15/0x20
pciehp_unconfigure_device+0x4d/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
What happens here is that the whole hierarchy is runtime resumed and the
parent PCIe downstream port, which got the hot-remove event, starts
removing devices below it, taking pci_lock_rescan_remove() lock. When the
child PCIe port is runtime resumed it calls pciehp_check_presence() which
ends up calling pciehp_card_present() and pciehp_check_link_active(). Both
of these use pcie_capability_read_word(), which notices that the underlying
device is already gone and returns PCIBIOS_DEVICE_NOT_FOUND with the
capability value set to 0. When pciehp gets this value it thinks that its
child device is also hot-removed and schedules its IRQ thread to handle the
event.
The deadlock happens when the child's IRQ thread runs and tries to acquire
pci_lock_rescan_remove() which is already taken by the parent and the
parent waits for the child's IRQ thread to finish.
Prevent this from happening by checking the return value of
pcie_capability_read_word() and if it is PCIBIOS_DEVICE_NOT_FOUND stop
performing any hot-removal activities.
[bhelgaas: add common scenarios to commit log]
Link: https://lore.kernel.org/r/20191029170022.57528-2-mika.westerberg@linux.intel.com
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We try to keep PCIe hotplug ports runtime suspended when entering system
suspend. Because the PCIe portdrv sets the DPM_FLAG_NEVER_SKIP flag, the PM
core always calls system suspend/resume hooks even if the device is left
runtime suspended. Since PCIe hotplug driver re-used the same function for
both runtime suspend and system suspend, it ended up disabling hotplug
interrupt twice and the second time following was printed:
pciehp 0000:03:01.0:pcie204: pcie_do_write_cmd: no response from device
Prevent this from happening by checking whether the device is already
runtime suspended when the system suspend hook is called.
Fixes: 9c62f0bfb8 ("PCI: pciehp: Implement runtime PM callbacks")
Link: https://lore.kernel.org/r/20191029170022.57528-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The R-Car Gen2/3 manual - available at:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg1m.html#documents
"RZ/G Series User's Manual: Hardware" section
strictly enforces the MACCTLR inizialization value - 39.3.1 - "Initial
Setting of PCI Express":
"Be sure to write the initial value (= H'80FF 0000) to MACCTLR before
enabling PCIETCTLR.CFINIT".
To avoid unexpected behavior and to match the SW initialization sequence
guidelines, this patch programs the MACCTLR with the correct value.
Note that the MACCTLR.SPCHG bit in the MACCTLR register description
reports that "Only writing 1 is valid and writing 0 is invalid" but this
"invalid" has to be interpreted as a write-ignore aka "ignored", not
"prohibited".
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Fixes: be20bbcb0a ("PCI: rcar: Add the initialization of PCIe link in resume_noirq()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v5.2+
Infinite timeout loops are hard to read. Refactor it to plausible 'do {}
while ()'.
Note, the supplied timeout can't be negative for current use, though if
it's not dividable to 10, we may go below 0, that's why type of the
parameter is int. And thus, we may move the check to the loop condition.
No functional change intended.
Link: https://lore.kernel.org/r/20191108111855.85866-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Enhance the ACS quirk for Cavium Processors. Add the root port vendor IDs
for ThunderX2 and ThunderX3 series of processors.
[bhelgaas: add Fixes: and stable tag]
Fixes: f2ddaf8dfd ("PCI: Apply Cavium ThunderX ACS quirk to more Root Ports")
Link: https://lore.kernel.org/r/20191111024243.GA11408@dc5-eodlnx05.marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rrichter@marvell.com>
Cc: stable@vger.kernel.org # v4.12+
Cadence core library files may be used by various platform drivers.
Add a new directory "cadence" to group all the Cadence core library files
and the platforms using Cadence core library.
Signed-off-by: Tom Joseph <tjoseph@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cadence PCIe host and endpoint IP may be embedded into a variety of
SoCs/platforms. Let's extract the platform related APIs/Structures in the
current driver to a separate file (pcie-cadence-plat.c), such that the
common functionality can be used by future platforms.
Signed-off-by: Tom Joseph <tjoseph@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Due to hardware constraints, the size of each inbound range entry
populated into the controller cannot be larger than the alignment
of the entry's start address. Currently, the alignment for each
"dma-ranges" inbound range is calculated only once for each range
and the increment for programming the controller is also derived
from it only once. Thus, a "dma-ranges" entry describing a memory
at 0x48000000 and size 0x38000000 would lead to multiple controller
entries, each 0x08000000 long.
This is inefficient, especially considering that by adding the size
to the start address, the alignment increases. This patch moves the
alignment calculation into the loop populating the controller entries,
thus updating the alignment for each controller entry.
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Since the 'idx' variable value is stored across multiple calls to
rcar_pcie_inbound_ranges() function, and the 'idx' value is used to
index registers which are written, subsequent calls might cause
the 'idx' value to be high enough to trigger writes into nonexistent
registers.
Fix this by moving the 'idx' value check to the beginning of the loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Remove unnecessary header include (../pci.h) since it doesn't
provide any needed symbols.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the LS1028a PCIe controller.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <Andrew.Murray@arm.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Since commit a574795bc3 ("PCI: generic,versatile: Remove unused
pci_sys_data structures") the build dependency on ARM is gone, so let's
enable COMPILE_TEST for versatile.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PHYS_OFFSET is not universally defined on all arches and using it prevents
enabling COMPILE_TEST. PAGE_OFFSET and __pa() are always available, so use
them to get the physical start of memory address.
This should have probably used 'dma-ranges' to get the address, but we
don't want to force a DT update to do that. At least in QEMU, the SMAP
registers have no effect (or perhaps the only value that is handled is 0).
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert ARM Versatile host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert the xilinx-nwl host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Convert the Xilinx host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Convert the xgene host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert V3 host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip host bridge driver doesn't need to store outboard resources
in its private struct as they are already stored in struct
pci_host_bridge.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Convert the Rockchip host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Convert the Mobiveil host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert Mediatek host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Convert the iProc host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list, so just use
bridge->windows directly.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Convert the Faraday host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert the Designware host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert altera host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
If an I/O range is present, then it will now be mapped. It's expected
that h/w which doesn't support I/O range will not define one.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: rfi@lists.rocketboards.org
Convert aardvark to use the common pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
pci_parse_request_of_pci_ranges() is missing a module export, so add it.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Prior to eed85ff4c0 ("PCI/DPC: Enable DPC only if AER is available"),
Linux handled DPC events regardless of whether firmware had granted it
ownership of AER or DPC, e.g., via _OSC.
PCIe r5.0, sec 6.2.10, recommends that the OS link control of DPC to
control of AER, so after eed85ff4c0, Linux handles DPC events only if it
has control of AER.
On platforms that do not grant OS control of AER via _OSC, Linux DPC
handling worked before eed85ff4c0 but not after.
To make Linux DPC handling work on those platforms the same way they did
before, add a "pcie_ports=dpc-native" kernel parameter that makes Linux
handle DPC events regardless of whether it has control of AER.
[bhelgaas: commit log, move pcie_ports_dpc_native to drivers/pci/]
Link: https://lore.kernel.org/r/20191023192205.97024-1-olof@lixom.net
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Invalidate PAXB inbound/outbound address mapping on probe before
programming it.
Kernel relies on outbound/inbound windows VALID bit in OARR registers to
detect if a window was programmed and if it is set it does not overwrite
it.
This causes issues on soft reboot (eg kexec) since the host controller
does not go through a HW reset on softboot so the kernel detects valid
outbound/inbound windows configuration and is not able to reprogramme
it as expected.
Therefore, in order to make sure outbound/inbound windows are
reprogrammed on soft reboot (eg kexec), invalidate memory windows on
each probe to fix the issue.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
In pci_call_probe(), we try to run driver probe functions on the node where
the device is attached. If we don't know which node the device is attached
to, the driver will likely run on the wrong node. This will still work,
but performance will not be as good as it could be.
On NUMA systems, warn if we don't know which node a PCI host bridge is
attached to. This is likely an indication that ACPI didn't supply a _PXM
method or the DT didn't supply a "numa-node-id" property.
[bhelgaas: commit log, check bus node]
Link: https://lore.kernel.org/r/1571467543-26125-1-git-send-email-linyunsheng@huawei.com
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The existing "pci=hpmemsize=nn[KMG]" kernel parameter overrides the default
size of both the non-prefetchable and the prefetchable MMIO windows for
hotplug bridges.
Add "pci=hpmmiosize=nn[KMG]" to override the default size of only the
non-prefetchable MMIO window.
Add "pci=hpmmioprefsize=nn[KMG]" to override the default size of only the
prefetchable MMIO window.
Link: https://lore.kernel.org/r/SL2P216MB0187E4D0055791957B7E2660806B0@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A driver may want to know the existence of _PR3, to choose different
runtime suspend behavior. A user will be add in next patch.
This is mostly the same as nouveau_pr3_present().
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20191018073848.14590-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kernel-doc validator complains:
aer.c:207: warning: Function parameter or member 'str' not described in 'pcie_ecrc_get_policy'
aer.c:1209: warning: Function parameter or member 'irq' not described in 'aer_isr'
aer.c:1209: warning: Function parameter or member 'context' not described in 'aer_isr'
aer.c:1209: warning: Excess function parameter 'work' description in 'aer_isr'
Fix the above accordingly.
Link: https://lore.kernel.org/r/20190827151823.75312-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
The elements in the aer_uncorrectable_error_string[] refer to the bit names
in Uncorrectable Error Status Register. Add PoisonTLPBlocked, which was
added in PCIe r3.1, sec 7.10.2.
Link: https://lore.kernel.org/r/20190827222145.32642-1-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we did not save and restore the AER configuration on
suspend/resume, so the configuration may be lost after resume.
Save the AER configuration during suspend and restore it during resume.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/92EBB4272BF81E4089A7126EC1E7B28492C3B007@IRSMSX101.ger.corp.intel.com
Signed-off-by: Mayurkumar Patel <mayurkumar.patel@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Corrects the programming to provide REFCLK to the downstream device
when there is no CLKREQ sideband signal routing present from root port
to the endpont.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Perform conversion to little-endian before every write to configuration
space and convert it back to CPU endianness on reads.
Additionally, initialise every multiple byte field of config space with
the cpu_to_le* macro, which is required since the structure describing
config space of emulated bridge assumes little-endian convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Initialise every multiple-byte field of emulated PCI bridge config
space with proper cpu_to_le* macro. This is required since the structure
describing config space of emulated bridge assumes little-endian
convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the return type of mvebu_pcie_map_registers in the
error path to have __iomem on it. Fixes the following
sparse warning:
drivers/pci/controller/pci-mvebu.c:716:31: warning: incorrect type in return expression (different address spaces)
drivers/pci/controller/pci-mvebu.c:716:31: expected void [noderef] <asn:2> *
drivers/pci/controller/pci-mvebu.c:716:31: got void *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
The mvebu_pci_bridge_emul_ops is not exported outside
of the driver, so make it static to avoid the following
sparse warning:
drivers/pci/controller/pci-mvebu.c:557:28: warning: symbol 'mvebu_pci_bridge_emul_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
There is an arbitrary difference between the system resume and
runtime resume code paths for PCI devices regarding the delay to
apply when switching the devices from D3cold to D0.
Namely, pci_restore_standard_config() used in the runtime resume
code path calls pci_set_power_state() which in turn invokes
__pci_start_power_transition() to power up the device through the
platform firmware and that function applies the transition delay
(as per PCI Express Base Specification Revision 2.0, Section 6.6.1).
However, pci_pm_default_resume_early() used in the system resume
code path calls pci_power_up() which doesn't apply the delay at
all and that causes issues to occur during resume from
suspend-to-idle on some systems where the delay is required.
Since there is no reason for that difference to exist, modify
pci_power_up() to follow pci_set_power_state() more closely and
invoke __pci_start_power_transition() from there to call the
platform firmware to power up the device (in case that's necessary).
Fixes: db288c9c5f ("PCI / PM: restore the original behavior of pci_set_power_state()")
Reported-by: Daniel Drake <drake@endlessm.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/linux-pm/CAD8Lp44TYxrMgPLkHCqF9hv6smEurMXvmmvmtyFhZ6Q4SE+dig@mail.gmail.com/T/#m21be74af263c6a34f36e0fc5c77c5449d9406925
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
When sriov_numvfs is being updated, we call the driver->sriov_configure()
function, which may enable VFs and call probe functions, which may make new
devices visible. This all happens before before sriov_numvfs_store()
updates sriov->num_VFs, so previously, concurrent sysfs reads of
sriov_numvfs returned stale values.
Serialize the sysfs read vs the write so the read returns the correct
num_VFs value.
[bhelgaas: hold device_lock instead of checking mutex_is_locked()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202991
Link: https://lore.kernel.org/r/20190911072736.32091-1-pierre.cregut@orange.com
Signed-off-by: Pierre Crégut <pierre.cregut@orange.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel Visual Compute Accelerator (VCA) is a family of PCIe add-in devices
exposing computational units via Non Transparent Bridges (NTB, PEX 87xx).
Similarly to MIC x200, we need to add DMA aliases to allow buffer access
when IOMMU is enabled.
Add aliases to allow computational unit access to host memory. These
aliases mark the whole VCA device as one IOMMU group.
All possible slot numbers (0x20) are used, since we are unable to tell what
slot is used on other side. This quirk is intended for both host and
computational unit sides. The VCA devices have up to five functions: four
for DMA channels and one additional.
Link: https://lore.kernel.org/r/5683A335CC8BE1438C3C30C49DCC38DF637CED8E@IRSMSX102.ger.corp.intel.com
Signed-off-by: Slawomir Pawlowski <slawomir.pawlowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslawx.kitszel@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
According to documentation [0] the correct offset for the Upstream Peer
Decode Configuration Register (UPDCR) is 0x1014. It was previously defined
as 0x1114.
d99321b63b ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
intended to enforce isolation between PCI devices allowing them to be put
into separate IOMMU groups. Due to the wrong register offset the intended
isolation was not fully enforced. This is fixed with this patch.
Please note that I did not test this patch because I have no hardware that
implements this register.
[0] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/4th-gen-core-family-mobile-i-o-datasheet.pdf (page 325)
Fixes: d99321b63b ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
Link: https://lore.kernel.org/r/7a3505df-79ba-8a28-464c-88b83eefffa6@kernkonzept.com
Signed-off-by: Steffen Liebergeld <steffen.liebergeld@kernkonzept.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org # v3.15+
These interfaces:
void pci_restore_pri_state(struct pci_dev *pdev);
void pci_restore_pasid_state(struct pci_dev *pdev);
are only used in drivers/pci and do not need to be seen by the rest of the
kernel. Most them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The following functions are only used by the PCI core or by IOMMU drivers
that cannot be modular, so there's no need to export them at all:
pci_enable_ats()
pci_disable_ats()
pci_restore_ats_state()
pci_ats_queue_depth()
pci_ats_page_aligned()
pci_enable_pri()
pci_restore_pri_state()
pci_reset_pri()
pci_prg_resp_pasid_required()
pci_enable_pasid()
pci_disable_pasid()
pci_restore_pasid_state()
pci_pasid_features()
pci_max_pasids()
Remove the unnecessary EXPORT_SYMBOL_GPL()s.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The PRG Response PASID Required bit in the PRI Capability is read-only.
Read it once when we enumerate the device and cache the value so we don't
need to read it again.
Based-on-patch-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we didn't disable the PF ATS until all associated VFs had
disabled it. But per PCIe spec r5.0, sec 9.3.7.8, the ATS Capability in
VFs and associated PFs may be enabled independently. Leaving ATS enabled
in the PF unnecessarily may have power and performance impacts.
Remove this dependency logic in the ATS enable/disable code.
[bhelgaas: commit log]
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/8163ab8fa66afd2cba514ae95d29ab12104781aa.1567029860.git.sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://lore.kernel.org/r/20190905193146.90250-4-helgaas@kernel.org
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Per PCIe r5.0, sec 9.3.7.14, if a PF implements the PASID Capability, the
PF PASID configuration is shared by its VFs. VFs must not implement their
own PASID Capability. Since VFs don't have a PASID Capability,
pci_enable_pasid() always failed, which caused IOMMU setup to fail.
Update the PASID interfaces so for VFs they reflect the state of the PF
PASID.
[bhelgaas: rebase without pasid_cap caching, commit log]
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/8ba1ac192e4ac737508b6ac15002158e176bab91.1567029860.git.sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://lore.kernel.org/r/20190905193146.90250-3-helgaas@kernel.org
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Per PCIe r5.0, sec 9.3.7.11, VFs must not implement the PRI Capability. If
the PF implements PRI, it is shared by the VFs. Since VFs don't have a PRI
Capability, pci_enable_pri() always failed, which caused IOMMU setup to
fail.
Update the PRI interfaces so for VFs they reflect the state of the PF PRI.
[bhelgaas: rebase without pri_cap caching, commit log]
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/b971e31f8695980da8e4a7f93e3b6a3edba3edaa.1567029860.git.sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://lore.kernel.org/r/20190905193146.90250-2-helgaas@kernel.org
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
pci_prg_resp_pasid_required() returns the value of the "PRG Response PASID
Required" bit from the PRI capability, but the interface was previously
defined under #ifdef CONFIG_PCI_PASID.
Move it from CONFIG_PCI_PASID to CONFIG_PCI_PRI so it's with the other
PRI-related things.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Factor out getting the link associated with a pci_dev and use this helper
where appropriate. In addition this helper will be used in a subsequent
patch of this series.
Link: https://lore.kernel.org/r/19d33770-29de-a9af-4d85-f2b30269d383@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously Clock PM could not be re-enabled after being disabled by
pci_disable_link_state() because clkpm_capable was reset. Change this by
adding a clkpm_disable field similar to aspm_disable.
Link: https://lore.kernel.org/r/4e8a66db-7d53-4a66-c26c-f0037ffaa705@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for disabling states L1.1 and L1.2 to pci_disable_link_state().
Allow separate control of ASPM and PCI PM L1 substates.
Link: https://lore.kernel.org/r/d81f8036-c236-6463-48e7-ebcdcda85bba@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The lifetime of the link_state structure (bridge->link_state) is not the
same as the lifetime of "bridge" itself. The link_state is allocated by
pcie_aspm_init_link_state() after children of the bridge have been
enumerated, and it is deallocated by pcie_aspm_exit_link_state() after all
children of the bridge (but not the bridge itself) have been removed.
Previously pcie_aspm_enabled() acquired aspm_lock to ensure that
link_state was not deallocated while we're looking at it. But the fact
that the caller of pcie_aspm_enabled() holds a reference to @pdev means
there's always at least one child of the bridge, which means link_state
can't be deallocated.
Remove the unnecessary locking in pcie_aspm_enabled().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
find_next_bit() takes a parameter of size long, and performs arithmetic
that assumes that the argument is of size long.
Therefore we cannot pass a u32, since this will cause find_next_bit()
to read outside the stack buffer and will produce the following print:
BUG: KASAN: stack-out-of-bounds in find_next_bit+0x38/0xb0
Fixes: 1b497e6493 ("PCI: dwc: Fix uninitialized variable in dw_handle_msi_irq()")
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
RISCV has csr_read()/write() macros in arch/riscv/include/asm/csr.h.
The same function naming is used in the PCI mobiveil driver thus
causing build error.
Rename csr_[read,write][l,] to mobiveil_csr_read()/write() to fix it.
drivers/pci/controller/pcie-mobiveil.c:238:69: error: macro "csr_read" passed 3 arguments, but takes just 1
static u32 csr_read(struct mobiveil_pcie *pcie, u32 off, size_t size)
drivers/pci/controller/pcie-mobiveil.c:253:80: error: macro "csr_write" passed 4 arguments, but takes just 2
static void csr_write(struct mobiveil_pcie *pcie, u32 val, u32 off, size_t size)
Fixes: bcbe0d9a8d ("PCI: mobiveil: Unify register accessors")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Minghuan Lian <Minghuan.Lian@nxp.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Cc: Andrew Murray <andrew.murray@arm.com>
Modify pci_epc_mem_alloc_addr() to cast the variable 'pageno'
from type 'int' to 'phys_addr_t' before shifting left. This
cast is needed to avoid treating bit 31 of 'pageno' as the
sign bit which would otherwise get sign-extended to produce
a negative value. When added to the base address of PCI memory
space, the negative value would produce an invalid physical
address which falls before the start of the PCI memory space.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Amlogic G12A SoC using a separate shared PHY.
This adds support for fetching a PHY phandle and call the PHY init,
reset and power on/off calls instead of writing in the PHY register or
toggling the PHY reset line.
The MIPI clock and the PHY memory resource are only required for the
Amlogic AXG SoC PCIe PHY setup, thus these elements are ignored for
the Amlogic G12A having a separate shared PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Fix the clock names used in the probe function according
to the bindings.
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Normally asserting reset signal on gpio would be achieved with:
gpiod_set_value_cansleep(reset_gpio, 1);
Meson PCI driver set reset value to '0' instead of '1' as it takes into
account the PERST# signal polarity. The polarity should be taken care
in the device tree instead.
This fixes the reset assertion meaning and moves out the polarity
configuration in DT (please note that there is no DT currently using
this driver).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
advk_pcie_wait_pio() can be called while holding a spinlock (from
pci_bus_read_config_dword()), then depends on jiffies in order to
timeout while polling on PIO state registers. In the case the PIO
transaction failed, the timeout will never happen and will also cause
the cpu to stall.
This decrements a variable and wait instead of using jiffies.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
PCI_EXP_RTCTL is used to activate PME interrupt only, so writing into it
should not modify other interrupts' mask. The ISR mask polarity was also
inverted, when PCI_EXP_RTCTL_PMEIE is set PCIE_MSG_PM_PME_MASK mask bit
should actually be cleared.
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:
driver_probe_device()
really_probe()
...
pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
function and PERST# is asserted */
...
drv->probe()
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Aardvark's PCI_EXP_LNKSTA_LT flag in its link status register is not
implemented and does not reflect the actual link training state (the
flag is always set to 0). In order to support link re-training feature
this flag has to be emulated. The Link Training and Status State
Machine (LTSSM) flag in Aardvark LMI config register could be used as
a link training indicator. Indeed if the LTSSM is in L0 or upper state
then link training has completed (see [1]).
Unfortunately because after asking a link retraining it takes a while
for the LTSSM state to become less than 0x10 (due to L0s to recovery
state transition delays), LTSSM can still be in L0 while link training
has not finished yet. So this waits for link to be in recovery or lesser
state before returning after asking for a link retrain.
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, Table 4-14
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
Commit e80a91ad30 ("PCI: Add dma_ranges window list") added a
dma_ranges resource list, but failed to correctly free the list when
devm_pci_alloc_host_bridge() is used.
Only the iproc host bridge driver is using the dma_ranges list.
Fixes: e80a91ad30 ("PCI: Add dma_ranges window list")
Link: https://lore.kernel.org/r/20191008012325.25700-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
A sysfs request to enable or disable a PCIe hotplug slot should not
return before it has been carried out. That is sought to be achieved by
waiting until the controller's "pending_events" have been cleared.
However the IRQ thread pciehp_ist() clears the "pending_events" before
it acts on them. If pciehp_sysfs_enable_slot() / _disable_slot() happen
to check the "pending_events" after they have been cleared but while
pciehp_ist() is still running, the functions may return prematurely
with an incorrect return value.
Fix by introducing an "ist_running" flag which must be false before a sysfs
request is allowed to return.
Fixes: 32a8cef274 ("PCI: pciehp: Enable/disable exclusively from IRQ thread")
Link: https://lore.kernel.org/linux-pci/1562226638-54134-1-git-send-email-wangxiongfeng2@huawei.com
Link: https://lore.kernel.org/r/4174210466e27eb7e2243dd1d801d5f75baaffd8.1565345211.git.lukas@wunner.de
Reported-and-tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
The part_event_bitmap register is 64 bits wide, so read it with ioread64()
instead of the 32-bit ioread32().
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Link: https://lore.kernel.org/r/20190910195833.3891-1-logang@deltatee.com
Reported-by: Doug Meyer <dmeyer@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
Cc: Kelvin Cao <Kelvin.Cao@microchip.com>
pci_reassign_bridge_resources() can be called by pci_resize_resource() at
runtime, it walks the PCI tree up and down, and it isn't currently
protected against any changes or hotplug operation.
Hold the pci_bus_sem to protect it.
Link: https://lore.kernel.org/r/7339fd73ccaf58552737ab10008333fd9f7723f2.camel@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
- Fix mobiveil inbound window CPU base address setup (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix the CPU base address setup in inbound window
- Propagate regulator_get_optional() errors so callers can distinguish
real errors from optional regulators that are absent (Thierry Reding)
- Propagate devm_of_phy_get() errors so callers can distinguish
real errors from optional PHYs that are absent (Thierry Reding)
- Add Andrew Murray as PCI native driver reviewer (Lorenzo Pieralisi)
* remotes/lorenzo/pci/misc:
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: iproc: Propagate errors for optional PHYs
PCI: histb: Propagate errors for optional regulators
PCI: armada8x: Propagate errors for optional PHYs
PCI: imx6: Propagate errors for optional regulators
PCI: exynos: Propagate errors for optional PHYs
PCI: rockchip: Propagate errors for optional regulators
- Add mediatek support for MT7629 (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Add controller support for MT7629
dt-bindings: PCI: Add support for MT7629
- Mark Layerscape endpoint BARs 2 and 4 as 64-bit (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP so EP/RC can be built separately (Xiaowei
Bao)
* remotes/lorenzo/pci/layerscape:
PCI: layerscape: Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC separately
PCI: layerscape: Add the bar_fixed_64bit property to the endpoint driver
- Fix Hyper-V use-after-free in pci_dev removal (Dexuan Cui)
- Fix Hyper-V build error in non-sysfs config (Randy Dunlap)
- Reallocate to avoid Hyper-V domain number collisions (Haiyang Zhang)
- Use Hyper-V instance ID bytes 4-5 to reduce domain collisions (Haiyang
Zhang)
* remotes/lorenzo/pci/hv:
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
PCI: hv: Detect and fix Hyper-V PCI domain number collision
PCI: pci-hyperv: Fix build errors on non-SYSFS config
PCI: hv: Avoid use of hv_pci_dev->pci_slot after freeing it
- Make kirin_dw_pcie_ops constant (Nishka Dasgupta)
- Make DesignWare "num-lanes" property optional and remove from relevant
DTs (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
arm64: dts: fsl: Remove num-lanes property from PCIe nodes
ARM: dts: ls1021a: Remove num-lanes property from PCIe nodes
PCI: dwc: Return directly when num-lanes is not found
dt-bindings: PCI: designware: Remove the num-lanes from Required properties
PCI: kirin: Make structure kirin_dw_pcie_ops constant
- Convert pci_resource_to_user() to a weak function to remove
HAVE_ARCH_PCI_RESOURCE_TO_USER #defines (Denis Efremov)
- Use PCI_SRIOV_NUM_BARS for idiomatic loop structure (Denis Efremov)
- Fix Resizable BAR size suspend/restore for 1MB BARs (Sumit Saxena)
- Correct "pci=resource_alignment" example in documentation (Alexey
Kardashevskiy)
* pci/resource:
PCI: Correct pci=resource_alignment parameter example
PCI: Restore Resizable BAR size bits correctly for 1MB BARs
PCI: Use PCI_SRIOV_NUM_BARS in loops instead of PCI_IOV_RESOURCE_END
PCI: Convert pci_resource_to_user() to a weak function
# Conflicts:
# drivers/pci/pci.c
- Cleanup pciehp LED/indicator control with a new consolidated
pciehp_set_indicators() interface that controls both Attention and
Power Indicators (Denis Efremov)
* pci/pciehp:
PCI: pciehp: Refer to "Indicators" instead of "LEDs" in comments
PCI: pciehp: Remove pciehp_green_led_{on,off,blink}()
PCI: pciehp: Remove pciehp_set_attention_status()
PCI: pciehp: Combine adjacent indicator updates
PCI: pciehp: Add pciehp_set_indicators() to set both indicators
- Use devm_add_action_or_reset() helper (Fuqian Huang)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Convert sysfs device attributes from __ATTR() to DEVICE_ATTR() (Kelsey
Skunberg)
- Convert sysfs file permissions from S_IRUSR etc to octal (Kelsey
Skunberg)
- Move SR-IOV sysfs functions to iov.c (Kelsey Skunberg)
- Add pci_info_ratelimited() to ratelimit PCI messages separately
(Krzysztof Wilczynski)
- Fix "'static' not at beginning of declaration" warnings (Krzysztof
Wilczynski)
- Clean up resource_alignment parameter to not require static buffer
(Logan Gunthorpe)
- Add ACS quirk for iProc PAXB (Abhinav Ratna)
- Add pci_irq_vector() and other stubs for !CONFIG_PCI (Herbert Xu)
* pci/misc:
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
PCI: Add ACS quirk for iProc PAXB
PCI: Force trailing new line to resource_alignment_param in sysfs
PCI: Move pci_[get|set]_resource_alignment_param() into their callers
PCI: Clean up resource_alignment parameter to not require static buffer
PCI: Use static const struct, not const static struct
PCI: Add pci_info_ratelimited() to ratelimit PCI separately
PCI/IOV: Remove group write permission from sriov_numvfs, sriov_drivers_autoprobe
PCI/IOV: Move sysfs SR-IOV functions to iov.c
PCI: sysfs: Change permissions from symbolic to octal
PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()
PCI: sysfs: Define device attributes with DEVICE_ATTR*()
PCI: Mark expected switch fall-through
PCI: Use devm_add_action_or_reset()
- Consolidate _HPP & _HPX code in pci-acpi.h and remove unnecessary
struct hotplug_program_ops (Krzysztof Wilczynski)
- Fixup PCIe device types to remove the need for dev->has_secondary_link
(Mika Westerberg)
* pci/enumeration:
PCI: Get rid of dev->has_secondary_link flag
PCI: Make pcie_downstream_port() available outside of access.c
PCI/ACPI: Remove unnecessary struct hotplug_program_ops
PCI/ACPI: Move _HPP & _HPX functions to pci-acpi.c
PCI/ACPI: Rename _HPX structs from hpp_* to hpx_*
- Move many symbols from public linux/pci.h to subsystem-private
drivers/pci/pci.h (Kelsey Skunberg)
- Unexport pci_bus_get() and pci_bus_sem since they're not needed by
modules (Kelsey Skunberg)
- Remove unused pci_block_cfg_access() et al (Kelsey Skunberg)
* pci/encapsulate:
PCI: Make pci_set_of_node(), etc private
PCI: Make pci_enable_ptm() private
PCI: Make pcie_set_ecrc_checking(), pcie_ecrc_get_policy() private
PCI: Make pci_ats_init() private
PCI: Make pcie_update_link_speed() private
PCI: Make pci_bus_get(), pci_bus_put() private
PCI: Make pci_hotplug_io_size, mem_size, and bus_size private
PCI: Make pci_save_vc_state(), pci_restore_vc_state(), etc private
PCI: Make pci_get_host_bridge_device(), pci_put_host_bridge_device() private
PCI: Make pci_check_pme_status(), pci_pme_wakeup_bus() private
PCI: Make PCI_PM_* delay times private
PCI: Unexport pci_bus_sem
PCI: Unexport pci_bus_get() and pci_bus_put()
PCI: Remove pci_block_cfg_access() et al (unused)
Add support to get regulator information of 3.3V and 12V supplies of a PCIe
slot from the respective controller's device-tree node and enable those
supplies. This is required in platforms like p2972-0000 where the supplies
to x16 slot owned by C5 controller need to be enabled before attempting to
enumerate the devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support to configure sideband signal pins when the information is
present in the respective controller device-tree node.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fold in YueHaibing's fix for build error without CONFIG_PINCTRL;
https://lore.kernel.org/r/20190920014807.38288-1-yuehaibing@huawei.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
- Initial support for running on a system with an Ultravisor, which is software
that runs below the hypervisor and protects guests against some attacks by
the hypervisor.
- Support for building the kernel to run as a "Secure Virtual Machine", ie. as
a guest capable of running on a system with an Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with medium
sized DMA masks (> 32 && < 59 bits) to use more than 2GB of DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas macros, both
to make it more readable and also enable some future optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to:
Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Aneesh
Kumar K.V, Anju T Sudhakar, Anshuman Khandual, Balbir Singh, Benjamin
Herrenschmidt, Cédric Le Goater, Christophe JAILLET, Christophe Leroy,
Christopher M. Riedl, Christoph Hellwig, Claudio Carvalho, Daniel Axtens,
David Gibson, David Hildenbrand, Desnes A. Nunes do Rosario, Ganesh Goudar,
Gautham R. Shenoy, Greg Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari
Bathini, Joakim Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras,
Lianbo Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan Chancellor,
Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Qian Cai, Ram
Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm, Sam Bobroff, Santosh Sivaraj,
Segher Boessenkool, Sukadev Bhattiprolu, Thiago Bauermann, Thiago Jung
Bauermann, Thomas Gleixner, Tom Lendacky, Vasant Hegde.
-----BEGIN PGP SIGNATURE-----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=WlW+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This is a bit late, partly due to me travelling, and partly due to a
power outage knocking out some of my test systems *while* I was
travelling.
- Initial support for running on a system with an Ultravisor, which
is software that runs below the hypervisor and protects guests
against some attacks by the hypervisor.
- Support for building the kernel to run as a "Secure Virtual
Machine", ie. as a guest capable of running on a system with an
Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with
medium sized DMA masks (> 32 && < 59 bits) to use more than 2GB of
DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas
macros, both to make it more readable and also enable some future
optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to: Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Cédric Le Goater, Christophe
JAILLET, Christophe Leroy, Christopher M. Riedl, Christoph Hellwig,
Claudio Carvalho, Daniel Axtens, David Gibson, David Hildenbrand,
Desnes A. Nunes do Rosario, Ganesh Goudar, Gautham R. Shenoy, Greg
Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari Bathini, Joakim
Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras, Lianbo
Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Qian Cai, Ram Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm,
Sam Bobroff, Santosh Sivaraj, Segher Boessenkool, Sukadev Bhattiprolu,
Thiago Bauermann, Thiago Jung Bauermann, Thomas Gleixner, Tom
Lendacky, Vasant Hegde"
* tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (264 commits)
powerpc/mm/mce: Keep irqs disabled during lockless page table walk
powerpc: Use ftrace_graph_ret_addr() when unwinding
powerpc/ftrace: Enable HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
ftrace: Look up the address of return_to_handler() using helpers
powerpc: dump kernel log before carrying out fadump or kdump
docs: powerpc: Add missing documentation reference
powerpc/xmon: Fix output of XIVE IPI
powerpc/xmon: Improve output of XIVE interrupts
powerpc/mm/radix: remove useless kernel messages
powerpc/fadump: support holes in kernel boot memory area
powerpc/fadump: remove RMA_START and RMA_END macros
powerpc/fadump: update documentation about option to release opalcore
powerpc/fadump: consider f/w load area
powerpc/opalcore: provide an option to invalidate /sys/firmware/opal/core file
powerpc/opalcore: export /sys/firmware/opal/core for analysing opal crashes
powerpc/fadump: update documentation about CONFIG_PRESERVE_FA_DUMP
powerpc/fadump: add support to preserve crash data on FADUMP disabled kernel
powerpc/fadump: improve how crashed kernel's memory is reserved
powerpc/fadump: consider reserved ranges while releasing memory
powerpc/fadump: make crash memory ranges array allocation generic
...
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
Pull core irq updates from Thomas Gleixner:
"Updates from the irq departement:
- Update the interrupt spreading code so it handles numa node with
different CPU counts properly.
- A large overhaul of the ARM GiCv3 driver to support new PPI and SPI
ranges.
- Conversion of all alloc_fwnode() users to use physical addresses
instead of virtual addresses so the virtual addresses are not
leaked. The physical address is sufficient to identify the
associated interrupt chip.
- Add support for Marvel MMP3, Amlogic Meson SM1 interrupt chips.
- Enforce interrupt threading at compile time if RT is enabled.
- Small updates and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
irqchip/gic-v3-its: Fix LPI release for Multi-MSI devices
irqchip/uniphier-aidet: Use devm_platform_ioremap_resource()
irqdomain: Add the missing assignment of domain->fwnode for named fwnode
irqchip/mmp: Coexist with GIC root IRQ controller
irqchip/mmp: Mask off interrupts from other cores
irqchip/mmp: Add missing chained_irq_{enter,exit}()
irqchip/mmp: Do not use of_address_to_resource() to get mux regs
irqchip/meson-gpio: Add support for meson sm1 SoCs
dt-bindings: interrupt-controller: New binding for the meson sm1 SoCs
genirq/affinity: Remove const qualifier from node_to_cpumask argument
genirq/affinity: Spread vectors on node according to nr_cpu ratio
genirq/affinity: Improve __irq_build_affinity_masks()
irqchip: Remove dev_err() usage after platform_get_irq()
irqchip: Add include guard to irq-partition-percpu.h
irqchip/mmp: Do not call irq_set_default_host() on DT platforms
irqchip/gic-v3-its: Remove the redundant set_bit for lpi_map
irqchip/gic-v3: Add quirks for HIP06/07 invalid GICD_TYPER erratum 161010803
irqchip/gic: Skip DT quirks when evaluating IIDR-based quirks
irqchip/gic-v3: Warn about inconsistent implementations of extended ranges
irqchip/gic-v3: Add EPPI range support
...
The shadow offset scratchpad was moved to 0x2000-0x2010. Update the
location to get the correct shadow offset.
Fixes: 6788958e4f ("PCI: vmd: Assign membar addresses from shadow registers")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
VMD maps child device config spaces to the VMD Config BAR linearly
regardless of the starting bus offset. Because of this, the config
address decode must ignore starting bus offsets when mapping the BDF to
the config space address.
Fixes: 2a5a9c9a20 ("PCI: vmd: Add offset to bus numbers if necessary")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
-----BEGIN PGP SIGNATURE-----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=L5e+
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
Some PCIe controllers can be set to either Host or EP according to some
early boot FW. To make sure there is no discrepancy (e.g. FW configured
the port to EP mode while the DT specifies it as a host bridge or vice
versa), a check has been added for each mode.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This driver is DT based and utilizes the DesignWare APIs.
It allows using a smaller ECAM range for a larger bus range -
usually an entire bus uses 1MB of address space, but the driver
can use it for a larger number of buses. This is achieved by using a HW
mechanism which allows changing the BUS part of the "final" outgoing
config transaction. There are 2 HW regs, one which is basically a
bitmask determining which bits to take from the AXI transaction itself
and another which holds the complementary part programmed by the
driver.
All link initializations are handled by the boot FW.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The Root Port (identified by [1c36:0031]) doesn't support MSI-X. On some
platforms it is configured to not advertise the capability at all, while
on others it (mistakenly) does. This causes a panic during
initialization by the pcieport driver, since it tries to configure the
MSI-X capability. Specifically, when trying to access the MSI-X table
a "non-existing addr" exception occurs.
Example stacktrace snippet:
SError Interrupt on CPU2, code 0xbf000000 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc1-Jonny-14847-ge76f1d4a1828-dirty #33
Hardware name: Annapurna Labs Alpine V3 EVP (DT)
pstate: 80000005 (Nzcv daif -PAN -UAO)
pc : __pci_enable_msix_range+0x4e4/0x608
lr : __pci_enable_msix_range+0x498/0x608
sp : ffffff80117db700
x29: ffffff80117db700 x28: 0000000000000001
x27: 0000000000000001 x26: 0000000000000000
x25: ffffffd3e9d8c0b0 x24: 0000000000000000
x23: 0000000000000000 x22: 0000000000000000
x21: 0000000000000001 x20: 0000000000000000
x19: ffffffd3e9d8c000 x18: ffffffffffffffff
x17: 0000000000000000 x16: 0000000000000000
x15: ffffff80116496c8 x14: ffffffd3e9844503
x13: ffffffd3e9844502 x12: 0000000000000038
x11: ffffffffffffff00 x10: 0000000000000040
x9 : ffffff801165e270 x8 : ffffff801165e268
x7 : 0000000000000002 x6 : 00000000000000b2
x5 : ffffffd3e9d8c2c0 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 0000000000000000
x1 : 0000000000000000 x0 : ffffffd3e9844680
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc1-Jonny-14847-ge76f1d4a1828-dirty #33
Hardware name: Annapurna Labs Alpine V3 EVP (DT)
Call trace:
dump_backtrace+0x0/0x140
show_stack+0x14/0x20
dump_stack+0xa8/0xcc
panic+0x140/0x334
nmi_panic+0x6c/0x70
arm64_serror_panic+0x74/0x88
__pte_error+0x0/0x28
el1_error+0x84/0xf8
__pci_enable_msix_range+0x4e4/0x608
pci_alloc_irq_vectors_affinity+0xdc/0x150
pcie_port_device_register+0x2b8/0x4e0
pcie_portdrv_probe+0x34/0xf0
Notice that this quirk also disables MSI (which may work, but hasn't
been tested nor has a current use case), since currently there is no
standard way to disable only MSI-X.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The Amazon Annapurna Labs PCIe Root Port exposes the VPD capability,
but there is no actual support for it.
Trying to access the VPD (for example, as part of lspci -vv or when
reading the vpd sysfs file), results in the following warning print:
pcieport 0001:00:00.0: VPD access failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The Amazon's Annapurna Labs root ports don't advertise an ACS
capability, but they don't allow peer-to-peer transactions and do
validate bus numbers through the SMMU. Additionally, it's not possible
for one RP to pass traffic to another RP.
Signed-off-by: Ali Saidi <alisaidi@amazon.com>
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
As recommended by Azure host team, the bytes 4, 5 have more uniqueness
(info entropy) than bytes 8, 9 so use them as the PCI domain numbers.
On older hosts, bytes 4, 5 can also be used -- no backward compatibility
issues are introduced and the chance of collision is greatly reduced.
In the rare cases of collision, the driver code detects and finds
another number that is not in use.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Sasha Levin <sashal@kernel.org>
Add support for Synopsys DesignWare core IP based PCIe host controller
present in the Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
In some systems, the Device/Port Type in the PCI Express Capabilities
register incorrectly identifies upstream ports as downstream ports.
d0751b98df ("PCI: Add dev->has_secondary_link to track downstream PCIe
links") addressed this by adding pci_dev.has_secondary_link, which is set
for downstream ports. But this is confusing because pci_pcie_type()
sometimes gives the wrong answer, and it's not obvious that we should use
pci_dev.has_secondary_link instead.
Reduce the confusion by correcting the type of the port itself so that
pci_pcie_type() returns the actual type regardless of what the Device/Port
Type register claims it is. Update the users to call pci_pcie_type() and
pcie_downstream_port() accordingly, and remove pci_dev.has_secondary_link
completely.
Link: https://lore.kernel.org/linux-pci/20190703133953.GK128603@google.com/
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20190822085553.62697-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
pcie_downstream_port() is useful in other places where code needs to
determine whether the PCIe port is downstream so make it available outside
of access.c.
Link: https://lore.kernel.org/r/20190822085553.62697-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=PsGr
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for Linux 5.4 from Marc Zyngier:
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
iProc PAXB Root Ports don't advertise an ACS capability, but they do not
allow peer-to-peer transactions between Root Ports. Add an ACS quirk so
each Root Port can be in a separate IOMMU group.
[bhelgaas: commit log, comment, use common implementation style]
Link: https://lore.kernel.org/r/1566275985-25670-1-git-send-email-srinath.mannam@broadcom.com
Signed-off-by: Abhinav Ratna <abhinav.ratna@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
When 'pci=resource_alignment=' is specified on the command line, there is
no trailing new line. Then, when it's read through the corresponding sysfs
attribute, there will be no newline and a cat command will not show
correctly in a shell. If the parameter is set through sysfs a new line will
be stored and it will 'cat' correctly.
To solve this, append a new line character in the show function if one does
not already exist.
Link: https://lore.kernel.org/r/20190822161013.5481-4-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Both the functions pci_get_resource_alignment_param() and
pci_set_resource_alignment_param() are now only called in one place:
resource_alignment_show() and resource_alignment_store() respectively.
There is no value in this extra set of functions so move both into their
callers respectively.
[bhelgaas: fold in "GFP_KERNEL while atomic" fix from Christoph Hellwig
<hch@infradead.org>
https://lore.kernel.org/r/20190902075006.GB754@infradead.org]
Link: https://lore.kernel.org/r/20190822161013.5481-3-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe spec doesn't mention "green LEDs" or "amber LEDs". Replace those
terms with "Power Indicator" and "Attention Indicator" so the comments
match the spec language. Comment changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove pciehp_green_led_{on,off,blink}() and use pciehp_set_indicators()
instead, since the code is mostly the same.
[bhelgaas: drop set_power_indicator() wrapper to reduce the number of
interfaces]
Link: https://lore.kernel.org/r/20190903111021.1559-5-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Remove pciehp_set_attention_status() and use pciehp_set_indicators()
instead, since the code is mostly the same.
Link: https://lore.kernel.org/r/20190903111021.1559-4-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Combine adjacent updates of power and attention indicators into a single
pciehp_set_indicators() call. This sends one command to the hotplug
controller instead of two.
Link: https://lore.kernel.org/r/20190903111021.1559-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Add pciehp_set_indicators() to set power and attention indicators with a
single register write.
This is a minor optimization because we frequently set both indicators and
this can do it with a single command. It also reduces the number of
interfaces related to the indicators and makes them more discoverable
because callers use the PCI_EXP_SLTCTL_ATTN_IND_* and
PCI_EXP_SLTCTL_PWR_IND_* definitions directly.
[bhelgaas: extend commit log, s/PCI_EXP_SLTCTL_.*_IND_NONE/INDICATOR_NOOP/
so they don't look like things defined by the spec, add function doc, mask
commands to make it obvious we only send valid commands
(pcie_do_write_cmd() does mask it, but requires more effort to verify)]
Link: https://lore.kernel.org/r/20190903111021.1559-2-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clean up the 'resource_alignment' parameter code to use kstrdup() in the
initcall routine instead of a static buffer that wastes memory regardless
of whether the feature is used. This allows us to drop 'COMMAND_LINE_SIZE'
bytes (typically 256-4096 depending on architecture) of static data.
This is similar to what has been done for the 'disable_acs_redir'
parameter.
Link: https://lore.kernel.org/r/20190822161013.5481-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the static keyword to the front of declarations of pci_regs_behavior[]
and pcie_cap_regs_behavior[], which resolves compiler warnings when
building with "W=1":
drivers/pci/pci-bridge-emul.c:41:1: warning: ‘static’ is not at beginning of
declaration [-Wold-style-declaration]
const static struct pci_bridge_reg_behavior pci_regs_behavior[] = {
^
drivers/pci/pci-bridge-emul.c:176:1: warning: ‘static’ is not at beginning of
declaration [-Wold-style-declaration]
const static struct pci_bridge_reg_behavior pcie_cap_regs_behavior[] = {
^
Link: https://lore.kernel.org/r/20190826151436.4672-1-kw@linux.com
Link: https://lore.kernel.org/r/20190828131733.5817-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Do not use printk_ratelimit() in drivers/pci/pci.c as it shares the rate
limiting state with all other callers to the printk_ratelimit().
Add pci_info_ratelimited() (similar to pci_notice_ratelimited() added in
the commit a88a7b3eb0 ("vfio: Use dev_printk() when possible")) and use
it instead of printk_ratelimit() + pci_info().
Link: https://lore.kernel.org/r/20190825224616.8021-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously the sriov_numvfs and sriov_drivers_autoprobe sysfs files had
0664 permissions, which allowed group write. libvirt runs as root when
dealing with PCI, and it chowns files needed by qemu, so group write
permission should not be needed.
Change these permissions from 0664 to 0644, which is what DEVICE_ATTR_RW()
does by default.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20190905063226.43269-1-skunberg.kelsey@gmail.com
Link: https://lore.kernel.org/r/850cf536-0b72-d78c-efaf-855dcb391087@redhat.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Donald Dutile <ddutile@redhat.com>
pnv_php is generally used with PCIe bridges which provide a native
interface for setting the attention and power indicator LEDs. Wire up
those interfaces even if firmware does not have support for them (yet...)
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-11-oohall@gmail.com
Currently we check that an IODA2 compatible PHB is upstream of this slot.
This is mainly to avoid pnv_php creating slots for the various "virtual
PHBs" that we create for NVLink. There's no real need for this restriction
so allow it on IODA3.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-10-oohall@gmail.com
When performing EEH recovery of devices in a hotplug slot we need to use
the slot driver's ->reset_slot() callback to prevent spurious hotplug
events due to spurious DLActive and PresDet change interrupts. Add a
reset_slot() callback to pnv_php so we can handle recovery of devices
in pnv_php managed slots.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-9-oohall@gmail.com
devm_phy_get() can fail for a number of reasons besides probe deferral.
It can for example return -ENOMEM if it runs out of memory as it tries
to allocate devres structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_phy_optional_get() is a function that exactly
does what's required here, so use that instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
devm_of_phy_get_by_index() can fail for a number of reasons besides
probe deferral. It can for example return -ENOMEM if it runs out of
memory as it tries to allocate devres structures. Propagating only
-EPROBE_DEFER is problematic because it results in these legitimately
fatal errors being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get_by_index() returns -ENODEV in this
case, so that's the special case that we need to handle. So we propagate
all errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: kernel@pengutronix.de
Cc: linux-imx@nxp.com
devm_of_phy_get() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate devres structures. Propagating only -EPROBE_DEFER
is problematic because it results in these legitimately fatal errors
being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get() returns -ENODEV in this case, so
that's the special case that we need to handle. So we propagate all
errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
530210c781 ("of/irq: Replace of_irq with of_phandle_args") changed the
of_irq_parse_pci() parameter type but didn't change the corresponding
documentation. Update the function doc to match.
Link: https://lore.kernel.org/r/20190807132049.10304-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the ACPI-specific structs hpx_type0, hpx_type1, hpx_type2 and
hpx_type3 to drivers/pci/pci-acpi.c as they are not used anywhere else.
Then remove the struct hotplug_program_ops that has been shared between
drivers/pci/probe.c and drivers/pci/pci-acpi.c from drivers/pci/pci.h as it
is no longer needed.
The struct hotplug_program_ops was added by 87fcf12e84 ("PCI/ACPI: Remove
the need for 'struct hotplug_params'") and replaced previously used struct
hotplug_params enabling the support for the _HPX Type 3 Setting Record that
was added by f873c51a15 ("PCI/ACPI: Implement _HPX Type 3 Setting
Record").
The new struct allowed for the static functions such program_hpx_type0(),
program_hpx_type1(), etc., from the drivers/pci/probe.c to be called from
the function pci_acpi_program_hp_params() in the drivers/pci/pci-acpi.c.
Previously a programming of _HPX Type 0 was as follows:
drivers/pci/probe.c:
program_hpx_type0()
...
pci_configure_device()
hp_ops = {
.program_type0 = program_hpx_type0,
...
}
pci_acpi_program_hp_params(&hp_ops)
drivers/pci/pci-acpi.c:
pci_acpi_program_hp_params(&hp_ops)
acpi_run_hpx(hp_ops)
decode_type0_hpx_record()
hp_ops->program_type0 # program_hpx_type0() called via hp_ops
After the ACPI-specific functions, structs, enums, etc., have been moved to
drivers/pci/pci-acpi.c there is no need for the hotplug_program_ops as all
of the _HPX Type 0, 1, 2 and 3 are directly accessible.
Link: https://lore.kernel.org/r/20190827094951.10613-4-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move program_hpx_type0(), program_hpx_type1(), etc., and enums
hpx_type3_dev_type, hpx_type3_fn_type and hpx_type3_cfg_loc to
drivers/pci/pci-acpi.c as these functions and enums are ACPI-specific.
Move structs hpx_type0, hpx_type1, hpx_type2 and hpx_type3 to
drivers/pci/pci.h as these are shared between drivers/pci/pci-acpi.c and
drivers/pci/probe.c.
Link: https://lore.kernel.org/r/20190827094951.10613-3-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The names of the hpp_type0, hpp_type1 and hpp_type2 structs suggest that
they're related to _HPP, when in fact they're related to _HPX.
The struct hpp_type0 denotes an _HPX Type 0 setting record that supersedes
the _HPP setting record, and it has been used interchangeably for _HPP as
per the ACPI specification (see version 6.3, section 6.2.9.1) which states
that it should be applied to PCI, PCI-X and PCI Express devices, with
settings being ignored if they are not applicable.
Rename them to hpx_type0, hpx_type1 and hpx_type2 to reflect their relation
to _HPX rather than _HPP.
Link: https://lore.kernel.org/r/20190827094951.10613-2-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=APp7
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Reset both NVIDIA GPU and HDA in ThinkPad P50 quirk, which was broken
by another quirk that enabled the HDA device (Lyude Paul)
- Fix pciebus-howto.rst documentation filename typo (Bjorn Helgaas)
* tag 'pci-v5.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Documentation PCI: Fix pciebus-howto.rst filename typo
PCI: Reset both NVIDIA GPU and HDA in ThinkPad P50 workaround
The num-lanes is optional since it is not needed on some platforms
that bring up the link in firmware.
The link programming is based on the num-lanes properties (which is
optional); if it is not present code must return instead of fiddling
with the lanes value to print an error message.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
This interface driver is a helper driver allows other drivers to
have a common interface with the Hyper-V PCI frontend driver.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Windows SR-IOV provides a backchannel mechanism in software for communication
between a VF driver and a PF driver. These "configuration blocks" are
similar in concept to PCI configuration space, but instead of doing reads and
writes in 32-bit chunks through a very slow path, packets of up to 128 bytes
can be sent or received asynchronously.
Nearly every SR-IOV device contains just such a communications channel in
hardware, so using this one in software is usually optional. Using the
software channel, however, allows driver implementers to leverage software
tools that fuzz the communications channel looking for vulnerabilities.
The usage model for these packets puts the responsibility for reading or
writing on the VF driver. The VF driver sends a read or a write packet,
indicating which "block" is being referred to by number.
If the PF driver wishes to initiate communication, it can "invalidate" one or
more of the first 64 blocks. This invalidation is delivered via a callback
supplied by the VF driver by this driver.
No protocol is implied, except that supplied by the PF and VF drivers.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code erroneously sets-up the CPU base address through the
parameter 'pci_addr', which is passed to initialize the CPU (AXI) base
address of the inbound window where the controller maps the PCI address
space into CPU physical address space; furthermore, it also truncates it
by programming only the lower 32-bit value into the inbound CPU address
register.
Fix both issues by introducing a new parameter 'u64 cpu_addr' to
initialize both lower 32-bit and upper 32-bit of the CPU physical
base address mapping PCI inbound transactions into CPU (AXI) ones.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Static variable kirin_dw_pcie_ops, of type dw_pcie_ops, is used only
once, when it is assigned to the constant field ops of variable pci
(having type dw_pcie) so kirin_dw_pcie_ops is never modified.
Make it constant to protect it from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Currently in Azure cloud, for passthrough devices, the host sets the
device instance ID's bytes 8 - 15 to a value derived from the host HWID,
which is the same on all devices in a VM. So, the device instance ID's
bytes 8 and 9 provided by the host are no longer unique. This affects
all Azure hosts since July 2018, and can cause device passthrough to VMs
to fail because the bytes 8 and 9 are used as PCI domain number.
Collision of domain numbers will cause the second device with the same
domain number fail to load.
In the cases of collision, we will detect and find another number that is
not in use.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Sasha Levin <sashal@kernel.org>
The sysfs SR-IOV functions are only needed when the kernel is built with
SR-IOV support. Rather than put them in pci-sysfs.c under #ifdef
CONFIG_PCI_IOV, move them to iov.c, which is only compiled when
CONFIG_PCI_IOV=y.
Link: https://lore.kernel.org/r/20190813204513.4790-4-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Donald Dutile <ddutile@redhat.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
DEVICE_ATTR() should only be used when files have unusual permissions.
Change DEVICE_ATTR() with '0220' write-only permissions to
DEVICE_ATTR_WO(), e.g.,
- static DEVICE_ATTR(_name, (S_IWUSR | S_IWGRP), NULL, _store);
+ static DEVICE_ATTR_WO(_name);
Since _store is no longer passed, make the _name passed by DEVICE_ATTR_WO()
and the related _name##_store() name match with each other, e.g.,
DEVICE_ATTR_WO(bus_rescan) must be able to call bus_rescan_store()
Link: https://lore.kernel.org/r/20190815153352.86143-4-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Donald Dutile <ddutile@redhat.com>
Any hardware that can potentially generate DMA has to be locked down in
order to avoid it being possible for an attacker to modify kernel code,
allowing them to circumvent disabled module loading or module signing.
Default to paranoid - in future we can potentially relax this for
sufficiently IOMMU-isolated devices.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
cc: linux-pci@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-6-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
Intel devices do not have good support for P2P requests that span different
host bridges as the transactions will cross the QPI/UPI bus and this does
not perform well.
Therefore, enable support for these devices only if the host bridges match.
Add Intel devices that have been tested and are known to work. There are
likely many others out there that will need to be tested and added.
Link: https://lore.kernel.org/r/20190730163545.4915-8-logang@deltatee.com
Link: https://lore.kernel.org/r/20190812173048.9186-8-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Push both PCI devices into the whitelist checking function seeing some
hardware will require us ensuring they are on the same host bridge.
At the same time we rename root_complex_whitelist() to
host_bridge_whitelist() to match the terminology used in the code.
Link: https://lore.kernel.org/r/20190730163545.4915-7-logang@deltatee.com
Link: https://lore.kernel.org/r/20190812173048.9186-7-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When a P2PDMA transfer is rejected due to ACS being set, we can also check
the whitelist and allow the transactions.
Do this by pushing the whitelist check into the upstream_bridge_distance()
function.
Link: https://lore.kernel.org/r/20190730163545.4915-6-logang@deltatee.com
Link: https://lore.kernel.org/r/20190812173048.9186-6-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add constant flags to indicate how two devices will be mapped or if they
are unsupported. upstream_bridge_distance() will now return the
mapping type and the distance in a passed-by-reference argument.
This helps annotate the code better, but the main reason is so we can use
the information to store the required mapping method in an xarray.
Link: https://lore.kernel.org/r/20190730163545.4915-4-logang@deltatee.com
Link: https://lore.kernel.org/r/20190812173048.9186-4-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
quirk_reset_lenovo_thinkpad_50_nvgpu() resets NVIDIA GPUs to work around
an apparent BIOS defect. It previously used pci_reset_function(), and
the available method was a bus reset, which was fine because there was
only one function on the bus. After b516ea586d ("PCI: Enable NVIDIA
HDA controllers"), there are now two functions (the HDA controller and
the GPU itself) on the bus, so the reset fails.
Use pci_reset_bus() explicitly instead of pci_reset_function() since it's
OK to reset both devices.
[bhelgaas: commit log, add e0547c81bf]
Fixes: b516ea586d ("PCI: Enable NVIDIA HDA controllers")
Fixes: e0547c81bf ("PCI: Reset Lenovo ThinkPad P50 nvgpu at boot if necessary")
Link: https://lore.kernel.org/r/20190801220117.14952-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Aaron Plattner <aplattner@nvidia.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Maik Freudenberg <hhfeuer@gmx.de>
Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers
beyond that point, avoiding the following abort on a i.MX 6Quad:
# cat /sys/devices/soc0/soc/1ffc000.pcie/pci0000\:00/0000\:00\:00.0/config
[ 100.021433] Unhandled fault: imprecise external abort (0x1406) at 0xb6ea7000
...
[ 100.056423] PC is at dw_pcie_read+0x50/0x84
[ 100.060790] LR is at dw_pcie_rd_own_conf+0x44/0x48
...
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fix build errors when building almost-allmodconfig but with SYSFS
not set (not enabled). Fixes these build errors:
ERROR: "pci_destroy_slot" [drivers/pci/controller/pci-hyperv.ko] undefined!
ERROR: "pci_create_slot" [drivers/pci/controller/pci-hyperv.ko] undefined!
drivers/pci/slot.o is only built when SYSFS is enabled, so
pci-hyperv.o has an implicit dependency on SYSFS.
Make that explicit.
Also, depending on X86 && X86_64 is not needed, so just change that
to depend on X86_64.
Fixes: a15f2c08c7 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-hyperv@vger.kernel.org
Cc: Dexuan Cui <decui@microsoft.com>
Add CONFIG_PCI_LAYERSCAPE_EP so that endpoint and host controller
drivers can be built separately.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The layerscape PCIe controller have 4 BARs.
BAR0 and BAR1 are 32bit, BAR2 and BAR4 are 64bit and that's a
fixed hardware configuration.
Set the bar_fixed_64bit variable accordingly.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support to enable CDM (Configuration Dependent Module) register
check for any data corruption based on the DT property
'snps,enable-cdm-check'.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Export the dw_pcie_wait_for_link() function to be able to build drivers
using it as loadable modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move PCIe config space capability search API to common DesignWare file
as this can be used by both host and EP mode drivers.
Signed-off-by: Vidya Sagar <vidyaos@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Some of DesignWare core's DBI registers (a.k.a configuration space
registers) are write-protected with a lock without enabling which they
are read-only by default.
These write-protected registers are implementation specific. Tegra194's
BAR-0 register which is at offset 0x10 in the configuration space is an
example. Current implementation in dw_pcie_setup_rc() API attempts to
unlock those write-protected registers whenever they are updated and
lock them back again for writing.
Group all write-protected registers writes so that locking and unlocking
is performed once to avoid bloating the code with multiple unlock/lock
sequences for all those write-protected registers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Tegra PCIe rootports don't generate MSI interrupts for PME and AER events.
Since PCIe spec (Ref: r4.0 sec 7.7.1.2 and 7.7.2.2) doesn't support using
a mix of INTx and MSI/MSI-X, MSI needs to be disabled to avoid root ports
service drivers registering their respective ISRs with MSI interrupt and
to let only INTx be used for all events.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The slot must be removed before the pci_dev is removed, otherwise a panic
can happen due to use-after-free.
Fixes: 15becc2b56 ("PCI: hv: Add hv_pci_remove_slots() when we unload the driver")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Each iteration of for_each_child_of_node() executes of_node_put() on the
previous node, but in some return paths in the middle of the loop
of_node_put() is missing thus causing a reference leak.
Hence stash these mid-loop return values in a variable 'err' and add a
new label err_node_put which executes of_node_put() on the previous node
and returns 'err' on failure.
Change mid-loop return statements to point to jump to this label to
fix the reference leak.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add a function checking whether or not PCIe ASPM has been enabled for
a given device.
It will be used by the NVMe driver to decide how to handle the
device during system suspend.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Add RISC-V as an arch that supports PCI_MSI_IRQ_DOMAIN. The related change
to generate asm/msi.h is 251a448881 ("riscv: include generic support for
MSI irqdomains").
Link: https://lore.kernel.org/r/alpine.DEB.2.21.9999.1907251426450.32766@viisi.sifive.com
Signed-off-by: Wesley Terpstra <wesley@sifive.com>
[paul.walmsley@sifive.com: wrote patch description; split this
patch from the arch/riscv patch]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Mark switch cases where we are expecting to fall through.
This fixes the following warning (Building: allmodconfig i386):
drivers/pci/hotplug/ibmphp_res.c: In function ‘update_bridge_ranges’:
drivers/pci/hotplug/ibmphp_res.c:1943:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
function = 0x8;
~~~~~~~~~^~~~~
drivers/pci/hotplug/ibmphp_res.c:1944:6: note: here
case PCI_HEADER_TYPE_MULTIBRIDGE:
^~~~
Link: https://lore.kernel.org/r/20190802012248.GA22622@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
In a Resizable BAR Control Register, bits 13:8 control the size of the BAR.
The encoded values of these bits are as follows (see PCIe r5.0, sec
7.8.6.3):
Value BAR size
0 1 MB (2^20 bytes)
1 2 MB (2^21 bytes)
2 4 MB (2^22 bytes)
...
43 8 EB (2^63 bytes)
Previously we incorrectly set the BAR size bits for a 1 MB BAR to 0x1f
instead of 0, so devices that support that size, e.g., new megaraid_sas and
mpt3sas adapters, fail to initialize during resume from S3 sleep.
Correctly calculate the BAR size bits for Resizable BAR control registers.
Link: https://lore.kernel.org/r/20190725192552.24295-1-sumit.saxena@broadcom.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203939
Fixes: d3252ace0b ("PCI: Restore resized BAR state on resume")
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org # v4.19+
Writing loop conditions as "i < NUM" is a common C idiom; using "i <= END"
is unusual and thus prone to errors. Change loops to use the former.
Link: https://lore.kernel.org/r/20190806140715.19847-1-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
To allocate its fwnode that is then used to allocate an irqdomain,
the driver uses irq_domain_alloc_fwnode(), passing it a VA as an
identifier. This is a rather bad idea, as this address ends up
published in debugfs (and we want to move away from VAs there
anyway).
Instead, let's allocate a named fwnode by using the device GUID as
an identifier. It is allegedly unique, and can be traced back to
the original device.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
MT7629 is an ARM platform SoC which has the same PCIe IP as MT7622.
The HW default value of its PCI host controller Device ID is invalid,
fix it to match the hardware implementation.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
[lorenzo.pieralisi@arm.com: commit log/minor spelling update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
When building with -Wsometimes-uninitialized, clang warns:
drivers/pci/hotplug/rpaphp_core.c:243:14: warning: variable 'fndit' is
used uninitialized whenever 'for' loop exits because its condition is
false [-Wsometimes-uninitialized]
for (j = 0; j < entries; j++) {
^~~~~~~~~~~
drivers/pci/hotplug/rpaphp_core.c:256:6: note: uninitialized use occurs
here
if (fndit)
^~~~~
drivers/pci/hotplug/rpaphp_core.c:243:14: note: remove the condition if
it is always true
for (j = 0; j < entries; j++) {
^~~~~~~~~~~
drivers/pci/hotplug/rpaphp_core.c:233:14: note: initialize the variable
'fndit' to silence this warning
int j, fndit;
^
= 0
fndit is only used to gate a sprintf call, which can be moved into the
loop to simplify the code and eliminate the local variable, which will
fix this warning.
Fixes: 2fcf3ae508 ("hotplug/drc-info: Add code to search ibm,drc-info property")
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Joel Savitz <jsavitz@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/504
Link: https://lore.kernel.org/r/20190603221157.58502-1-natechancellor@gmail.com
These interfaces:
void pci_set_of_node(struct pci_dev *dev);
void pci_release_of_node(struct pci_dev *dev);
void pci_set_bus_of_node(struct pci_bus *bus);
void pci_release_bus_of_node(struct pci_bus *bus);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-12-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This interface:
int pci_enable_ptm(struct pci_dev *dev, u8 *granularity);
is only used in drivers/pci/ and does not need to be seen by the rest of
the kernel. Move it to drivers/pci/pci.h so it's private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-11-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
void pcie_set_ecrc_checking(struct pci_dev *dev);
void pcie_ecrc_get_policy(char *str);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-10-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This interface:
void pci_ats_init(struct pci_dev *dev);
is only used in drivers/pci/ and does not need to be seen by the rest of
the kernel. Move it to drivers/pci/pci.h so it's private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-9-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This interface:
void pcie_update_link_speed(struct pci_bus *bus, u16 link_status);
is only used in drivers/pci/ and does not need to be seen by the rest of
the kernel. Move it to drivers/pci/pci.h so it's private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-8-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
struct pci_bus *pci_bus_get(struct pci_bus *bus);
void pci_bus_put(struct pci_bus *bus);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-7-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These symbols:
extern unsigned long pci_hotplug_io_size;
extern unsigned long pci_hotplug_mem_size;
extern unsigned long pci_hotplug_bus_size;
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-6-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These Virtual Channel interfaces:
int pci_save_vc_state(struct pci_dev *dev);
void pci_restore_vc_state(struct pci_dev *dev);
void pci_allocate_vc_save_buffers(struct pci_dev *dev);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-5-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
struct device *pci_get_host_bridge_device(struct pci_dev *dev);
void pci_put_host_bridge_device(struct device *dev);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-4-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
bool pci_check_pme_status(struct pci_dev *dev);
void pci_pme_wakeup_bus(struct pci_bus *bus);
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-3-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These delay time definitions:
#define PCI_PM_D2_DELAY 200
#define PCI_PM_D3_WAIT 10
#define PCI_PM_D3COLD_WAIT 100
#define PCI_PM_BUS_WAIT 50
are only used in drivers/pci/ and do not need to be seen by the rest of the
kernel. Move them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Link: https://lore.kernel.org/r/20190724233848.73327-2-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a generic helper to match any/all devices. Using this
introduce new wrappers {bus/driver/class}_find_next_device().
Cc: Elie Morisse <syniurge@gmail.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI
Link: https://lore.kernel.org/r/20190723221838.12024-7-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_add_action_or_reset() is a helper function which internally calls
devm_add_action(). If the devm_add_action() fails, it will execute the
action mentioned and return the error code.
Use devm_add_action_or_reset() to reduce source code size (avoid writing
the action twice) and reduce the likelihood of bugs.
Link: https://lore.kernel.org/r/20190708123354.12127-1-huangfq.daxian@gmail.com
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_bus_sem is not used by a loadable kernel module and does not need to be
exported.
It was exported by ce29ca3ea4 ("PCI: acpiphp: remove all functions in
slot, even without ACPI _EJx"), which added a use of pci_bus_sem in
acpiphp, which could be built as a module at that time. But since
6037a803b0 ("PCI: acpiphp: Convert acpiphp to be builtin only, not
modular"), it can no longer be built as a module.
Link: https://lore.kernel.org/r/20190718032951.40188-1-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_bus_get() and pci_bus_put() are not used by a loadable kernel module
and do not need to be exported.
These were exported by fe830ef62a ("PCI: Introduce pci_bus_{get|put}() to
manage PCI bus reference count"), but there are no loadable modules in the
tree that use them.
Link: https://lore.kernel.org/r/20190717182353.45557-1-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <skunberg.kelsey@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
to test and use this feature in the NTB transport layer. Also, bug
fixes for the AMD and Switchtec drivers, as well as some general
patches.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoE9b9c3U2JxX98mqbmZLrHqL0iMFAl0w0EwACgkQbmZLrHqL
0iNt4RAAiw2Cb2y5D36jI+lPl8xN2REk4x7b/FKFfLSzM/7Bu1okprrElKO6735r
0wRpyZS5lbYYr0QybzMrNfDMLYywFmA+C7GY7gQpR7GLYLb9chmvOmubfEbakHYI
4qKAWgaZt6PaiLQp76y3bFjUiBrd8KzVi5J891lDKvjzsGUjdNeFSlPlDbzTP8H9
+pBxnYn4G7MxVTebxjpOs6bQPO1sJZl4cyW40avTC1x+6bMlU1B361IhwtuabQH8
6rq6MQbaDzHTpuBZqZR8O+JxFzpffnGRu+smWPNQS2p95AewGIaDUsjZ6ph81rF1
mUxt/UJYP0RlIY+RQQ0Ie3cBUZ/I7wQzpFAXnqb8Nzba4tpc9ITX04hfnWKg6Kr0
sgj2Ro6I4TS3TSw6vquwvR2hn6+RZi06z/D0AXdUl+R3QxJXMyZygDDPDpTImZNy
cnu+1Y7pdgjASXBvHKhM39+ynGLGze7xBIs6GO6TjJoVgZdMaW1/N/wsldYRc3Uf
K0VSHowGHOyIV8d33oYWK2oSgWFrRCCanrCXIltNwl6NM05/b474L/8fiSnJ37PZ
dJspdPdrut9W3018cRVHBhAX9csucbSa46FKz1Z0FEFjDJJzqy0isKDsoExBZqBH
AqCnP548sbJF9+yOC475W36KMHBhyNvLS8XxD2J3DQpPDMRj//Y=
=P1lR
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
new iommu device
vhost guest memory access using vmap (just meta-data for now)
minor fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Note: due to code driver changes the driver-core tree, the following
patch is needed when merging tree with commit 92ce7e83b4
("driver_find_device: Unify the match function with
class_find_device()") in the driver-core tree:
From: Nathan Chancellor <natechancellor@gmail.com>
Subject: [PATCH] iommu/virtio: Constify data parameter in viommu_match_node
After commit 92ce7e83b4 ("driver_find_device: Unify the match
function with class_find_device()") in the driver-core tree.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
---
drivers/iommu/virtio-iommu.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/iommu/virtio-iommu.c b/drivers/iommu/virtio-iommu.c
index 4620dd221ffd..433f4d2ee956 100644
--- a/drivers/iommu/virtio-iommu.c
+++ b/drivers/iommu/virtio-iommu.c
@@ -839,7 +839,7 @@ static void viommu_put_resv_regions(struct device *dev, struct list_head *head)
static struct iommu_ops viommu_ops;
static struct virtio_driver virtio_iommu_drv;
-static int viommu_match_node(struct device *dev, void *data)
+static int viommu_match_node(struct device *dev, const void *data)
{
return dev->parent->fwnode == data;
}
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdJ5qUAAoJECgfDbjSjVRpQs0H/2qWcIG1zjGKyh9KWrfgOusG
/QIqeP50d7SC6oqdyd00tzmExqO1xdGLPFzYixdOsU817te1gHBP4Rfmzo01jZRd
CUzZNnZQ2JRsDshiA6G2ui+wn1/a/cB3RPN4rT1mquDYS53QmsRGDQDnpp84TXMV
aocB8TS6halbRzKMq3VmaWHIvzNXnt4dwQR542+PyeLLn9bUx2QwWj2ON3QwxixK
dVRZow3GwLGBhKTA/Z1Z/Bta4fEfOKjUGP2XWgvL6zOr+nZR4eQ8w5WXVJYzR+d6
1JCfqTxleweT2k6Tu5VwtTNlQkxn/XvQAeisppOiEE6NnPjubyI9wMQIvL7bkpo=
=uJbC
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio, vhost updates from Michael Tsirkin:
"Fixes, features, performance:
- new iommu device
- vhost guest memory access using vmap (just meta-data for now)
- minor fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-mmio: add error check for platform_get_irq
scsi: virtio_scsi: Use struct_size() helper
iommu/virtio: Add event queue
iommu/virtio: Add probe request
iommu: Add virtio-iommu driver
PCI: OF: Initialize dev->fwnode appropriately
of: Allow the iommu-map property to omit untranslated devices
dt-bindings: virtio: Add virtio-pci-iommu node
dt-bindings: virtio-mmio: Add IOMMU description
vhost: fix clang build warning
vhost: access vq metadata through kernel virtual address
vhost: factor out setting vring addr and num
vhost: introduce helpers to get the size of metadata area
vhost: rename vq_iotlb_prefetch() to vq_meta_prefetch()
vhost: fine grain userspace memory accessors
vhost: generalize adding used elem
-----BEGIN PGP SIGNATURE-----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=smxY
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull rst conversion of docs from Mauro Carvalho Chehab:
"As agreed with Jon, I'm sending this big series directly to you, c/c
him, as this series required a special care, in order to avoid
conflicts with other trees"
* tag 'docs/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (77 commits)
docs: kbuild: fix build with pdf and fix some minor issues
docs: block: fix pdf output
docs: arm: fix a breakage with pdf output
docs: don't use nested tables
docs: gpio: add sysfs interface to the admin-guide
docs: locking: add it to the main index
docs: add some directories to the main documentation index
docs: add SPDX tags to new index files
docs: add a memory-devices subdir to driver-api
docs: phy: place documentation under driver-api
docs: serial: move it to the driver-api
docs: driver-api: add remaining converted dirs to it
docs: driver-api: add xilinx driver API documentation
docs: driver-api: add a series of orphaned documents
docs: admin-guide: add a series of orphaned documents
docs: cgroup-v1: add it to the admin-guide book
docs: aoe: add it to the driver-api book
docs: add some documentation dirs to the driver-api book
docs: driver-model: move it to the driver-api book
docs: lp855x-driver.rst: add it to the driver-api book
...
There are lots of documents under Documentation/*.txt and a few other
orphan documents elsehwere that belong to the driver-API book.
Move them to their right place.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> # vfio-related parts
Acked-by: Logan Gunthorpe <logang@deltatee.com> # switchtec
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Improvements and bug fixes for the hmm interface in the kernel:
- Improve clarity, locking and APIs related to the 'hmm mirror' feature
merged last cycle. In linux-next we now see AMDGPU and nouveau to be
using this API.
- Remove old or transitional hmm APIs. These are hold overs from the past
with no users, or APIs that existed only to manage cross tree conflicts.
There are still a few more of these cleanups that didn't make the merge
window cut off.
- Improve some core mm APIs:
* export alloc_pages_vma() for driver use
* refactor into devm_request_free_mem_region() to manage
DEVICE_PRIVATE resource reservations
* refactor duplicative driver code into the core dev_pagemap
struct
- Remove hmm wrappers of improved core mm APIs, instead have drivers use
the simplified API directly
- Remove DEVICE_PUBLIC
- Simplify the kconfig flow for the hmm users and core code
-----BEGIN PGP SIGNATURE-----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=wKvp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull HMM updates from Jason Gunthorpe:
"Improvements and bug fixes for the hmm interface in the kernel:
- Improve clarity, locking and APIs related to the 'hmm mirror'
feature merged last cycle. In linux-next we now see AMDGPU and
nouveau to be using this API.
- Remove old or transitional hmm APIs. These are hold overs from the
past with no users, or APIs that existed only to manage cross tree
conflicts. There are still a few more of these cleanups that didn't
make the merge window cut off.
- Improve some core mm APIs:
- export alloc_pages_vma() for driver use
- refactor into devm_request_free_mem_region() to manage
DEVICE_PRIVATE resource reservations
- refactor duplicative driver code into the core dev_pagemap
struct
- Remove hmm wrappers of improved core mm APIs, instead have drivers
use the simplified API directly
- Remove DEVICE_PUBLIC
- Simplify the kconfig flow for the hmm users and core code"
* tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (42 commits)
mm: don't select MIGRATE_VMA_HELPER from HMM_MIRROR
mm: remove the HMM config option
mm: sort out the DEVICE_PRIVATE Kconfig mess
mm: simplify ZONE_DEVICE page private data
mm: remove hmm_devmem_add
mm: remove hmm_vma_alloc_locked_page
nouveau: use devm_memremap_pages directly
nouveau: use alloc_page_vma directly
PCI/P2PDMA: use the dev_pagemap internal refcount
device-dax: use the dev_pagemap internal refcount
memremap: provide an optional internal refcount in struct dev_pagemap
memremap: replace the altmap_valid field with a PGMAP_ALTMAP_VALID flag
memremap: remove the data field in struct dev_pagemap
memremap: add a migrate_to_ram method to struct dev_pagemap_ops
memremap: lift the devmap_enable manipulation into devm_memremap_pages
memremap: pass a struct dev_pagemap to ->kill and ->cleanup
memremap: move dev_pagemap callbacks into a separate structure
memremap: validate the pagemap type passed to devm_memremap_pages
mm: factor out a devm_request_free_mem_region helper
mm: export alloc_pages_vma
...
- Complete PCI endpoint removal so a subsequent add doesn't fail with
-EBUSY (Alan Mikhak)
- Pay attention to PCI endpoint fixed-size BARs (Alan Mikhak)
- Fix PCI endpoint handling of 64bit BARs (Alan Mikhak)
- Clear PCI endpoint BARs before freeing space (Alan Mikhak)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Clear BAR before freeing its space
PCI: endpoint: Skip odd BAR when skipping 64bit BAR
PCI: endpoint: Allocate enough space for fixed size BAR
PCI: endpoint: Set endpoint controller pointer to NULL
- Reorganize Tegra AFI/PHY/REFCLK/etc functions (Manikanta Maddireddy)
- Mask Tegra AFI_INTR in runtime suspend (Manikanta Maddireddy)
- Fix Tegra AFI/PCIe powerup sequence (Manikanta Maddireddy)
- Add Tegra124, Tegra132, Tegra210, and Tegra186 support for Gen2 link
speed (Manikanta Maddireddy)
- Advertise Tegra AER support (Manikanta Maddireddy)
- Program Tegra210 UPHY settings (Manikanta Maddireddy)
- Enable Tegra opportunistic UpdateFC and ACK (Manikanta Maddireddy)
- Disable Tegra AFI dynamic clock gating (Manikanta Maddireddy)
- Process Tegra pending DLL transactions before entering L1 or L2 to
prevent receiver errors (Manikanta Maddireddy)
- Enable Tegra xclk clock clamping in L1 (Manikanta Maddireddy)
- Increase Tegra deskew retry time (Manikanta Maddireddy)
- Work around Tegra hardware RAW erratum (Manikanta Maddireddy)
- Update Tegra210 flow control timer frequency (Manikanta Maddireddy)
- Work around Tegra Gen1/Gen2 link number negotiation issue (Manikanta
Maddireddy)
- Work around Tegra PLLE power down issue (Manikanta Maddireddy)
- Program Tegra20 to support cacheable upstream transactions (Manikanta
Maddireddy)
- Log Tegra PRSNT_SENSE_IRQ as debug, not err (Manikanta Maddireddy)
- Add register offset for third Root Port on Tegra186 and Tegra30
(Manikanta Maddireddy)
- Document Tegra PCIe DPD pinctrl property (Manikanta Maddireddy)
- Put Tegra PEX CLK & BIAS pads in DPD mode to reduce power usage when
powergated (Manikanta Maddireddy)
- Add generic DT binding for "reset-gpios" property (Manikanta
Maddireddy)
- Add Tegra support for GPIO-based PERST# (Manikanta Maddireddy)
- Enable Relaxed Ordering only for Tegra20 & Tegra30 (Vidya Sagar)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Enable Relaxed Ordering only for Tegra20 & Tegra30
PCI: tegra: Change link retry log level to debug
PCI: tegra: Add support for GPIO based PERST#
PCI: Add DT binding for "reset-gpios" property
PCI: tegra: Put PEX CLK & BIAS pads in DPD mode
dt-bindings: pci: tegra: Document PCIe DPD pinctrl optional prop
PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct
PCI: tegra: Change PRSNT_SENSE IRQ log to debug
PCI: tegra: Program AFI_CACHE_BAR_{0,1}_{ST,SZ} registers only for Tegra20
PCI: tegra: Fix PLLE power down issue due to CLKREQ# signal
PCI: tegra: Set target speed as Gen1 before starting LTSSM
PCI: tegra: Update flow control timer frequency in Tegra210
PCI: tegra: Add SW fixup for RAW violations
PCI: tegra: Increase the deskew retry time
PCI: tegra: Enable PCIe xclk clock clamping
PCI: tegra: Process pending DLL transactions before entering L1 or L2
PCI: tegra: Disable AFI dynamic clock gating
PCI: tegra: Enable opportunistic UpdateFC and ACK
PCI: tegra: Program UPHY electrical settings for Tegra210
PCI: tegra: Advertise PCIe Advanced Error Reporting (AER) capability
PCI: tegra: Add PCIe Gen2 link speed support
PCI: tegra: Fix PCIe host power up sequence
PCI: tegra: Mask AFI_INTR in runtime suspend
PCI: tegra: Rearrange Tegra PCIe driver functions
PCI: tegra: Handle failure cases in tegra_pcie_power_on()
soc/tegra: pmc: Export tegra_powergate_power_on()
- Move qcom driver to bulk clock API (Bjorn Andersson)
- Add Qualcomm QCS404 PCIe controller support (Bjorn Andersson)
- Ensure Qualcomm PERST is asserted for at least 100ms (Niklas Cassel)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Ensure that PERST is asserted for at least 100 ms
PCI: qcom: Add QCS404 PCIe controller support
dt-bindings: PCI: qcom: Add QCS404 to the binding
PCI: qcom: Use clk bulk API for 2.4.0 controllers
- Unify mobiveil register accessors (Hou Zhiqiang)
- Remove MSI_FLAG_MULTI_PCI_MSI since mobiveil hardware doesn't support
Multiple MSI (Hou Zhiqiang)
- Program outbound windows with base address from DT instead of assuming
zero (Hou Zhiqiang)
- Skip "safe" list traversal when it's unnecessary (Hou Zhiqiang)
- Initialize WIN_NUM_0 explicitly for CFG outbound transactions (Hou
Zhiqiang)
- Use WIN_NUM_0 for MEM inbound transactions (Hou Zhiqiang)
- Fix up mobiveil Class Code to PCI_CLASS_BRIDGE_PCI (Hou Zhiqiang)
- Wait for link-up before enumerating devices, not while initializing
host (Hou Zhiqiang)
- Move IRQ chained handler setup out of DT code (Hou Zhiqiang)
- Set primary/secondary/subordinate bus numbers (Hou Zhiqiang)
- Fix "valid device" check to allow root bus device 0 to be
multi-function (Hou Zhiqiang)
- Make DT "gpio_slave" and "apb_csr" properties optional (Hou Zhiqiang)
- Refactor MEM/IO outbound window initialization (Hou Zhiqiang)
- Fix validity check for inbound/outbound window programming (Hou
Zhiqiang)
- Initialize and preserve window control bits (Hou Zhiqiang)
- Fix 64-bit outbound window setup (both CPU and PCI addresses) (Hou
Zhiqiang)
- Move IO port setup to host init (Hou Zhiqiang)
- Fix infinite loop in INTx ISR (Hou Zhiqiang)
- Fix INTx interrupt clearing to avoid missed interrupts (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr()
PCI: mobiveil: Fix infinite-loop in the INTx handling function
PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine
PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window
PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window
PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup
PCI: mobiveil: Clear the control fields before updating it
PCI: mobiveil: Add configured inbound windows counter
PCI: mobiveil: Fix the valid check for inbound and outbound windows
PCI: mobiveil: Clean-up program_{ib/ob}_windows()
PCI: mobiveil: Remove an unnecessary return value check
PCI: mobiveil: Fix error return values
PCI: mobiveil: Refactor the MEM/IO outbound window initialization
PCI: mobiveil: Make some register updates more readable
PCI: mobiveil: Reformat the code for readability
dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional
PCI: mobiveil: Fix devfn check in mobiveil_pcie_valid_device()
PCI: mobiveil: Initialize Primary/Secondary/Subordinate bus numbers
PCI: mobiveil: Move IRQ chained handler setup out of DT parse
PCI: mobiveil: Move the link up waiting out of mobiveil_host_init()
PCI: mobiveil: Fix the Class Code field
PCI: mobiveil: Use the 1st inbound window for MEM inbound transactions
PCI: mobiveil: Use WIN_NUM_0 explicitly for CFG outbound window
PCI: mobiveil: Update the resource list traversal function
PCI: mobiveil: Fix PCI base address in MEM/IO outbound windows
PCI: mobiveil: Remove the flag MSI_FLAG_MULTI_PCI_MSI
PCI: mobiveil: Unify register accessors
- Add dwc API support to de-initialize host (Vidya Sagar)
- Clean up dwc DBI,ATU read and write APIs (Vidya Sagar)
- Export dwc APIs to support .remove() so drivers can be modular (Vidya
Sagar)
- Simplify imx6 Kconfig dependencies (Leonard Crestez)
- Fix dra7xx build error when !CONFIG_GPIOLIB (YueHaibing)
* remotes/lorenzo/pci/dwc:
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: imx6: Simplify Kconfig depends on
PCI: dwc: Export APIs to support .remove() implementation
PCI: dwc: Cleanup DBI,ATU read and write APIs
PCI: dwc: Add API support to de-initialize host
- Allow building Altera host bridge driver as a module (Ley Foon Tan)
- Fix Altera Stratix 10 Type 1 to Type 0 config access conversion (Ley
Foon Tan)
* remotes/lorenzo/pci/altera:
PCI: altera: Fix configuration type based on secondary number
PCI: altera-msi: Allow building as module
PCI: altera: Allow building as module
- Fix problem with caching VF config space size (Alex Williamson)
* pci/virtualization:
PCI/IOV: Assume SR-IOV VFs support extended config space.
Revert "PCI/IOV: Use VF0 cached config space size for other VFs"
- Prevent drivers that use dma_virt_ops from using peer-to-peer DMA
(Logan Gunthorpe)
* pci/peer-to-peer:
PCI/P2PDMA: Fix missing check for dma_virt_ops
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
