This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable common clk framework for DT-based boards and disable code that
depends on the legacy sh clk framework when common clk is enabled.
Once legacy drivers are converted over, the old code can be removed
entirely.
Signed-off-by: Rich Felker <dalias@libc.org>
Support is hooked up via a cpu start method specified in the device
tree, and also depends on DT nodes that describe the interfaces for
performing IPI and identifying which cpu execution is taking place on.
The currently used method is a form of spin table, where secondary
cpus are unblocked by writing to a special address.
Signed-off-by: Rich Felker <dalias@libc.org>
The SH2 version of entry.S uses global variables, which need to be
cpu-local in order to work with SMP. For ease of access from asm,
simply use arrays indexed by cpu number, and require the availability
of an address (mmio register or properly setup per-cpu memory) from
which the current cpu's index can be read.
Signed-off-by: Rich Felker <dalias@libc.org>
The J-Core cpu has, as an ISA extension, an atomic compare-and-swap
instruction cas.l which applications need to use (instead the imask or
gusa atomic models, which are fundamentally limited to UP) for
synchronization in order to be compatible with SMP systems. Provide a
hwcap flag so that it's possible to do runtime selection and support
both.
Signed-off-by: Rich Felker <dalias@libc.org>
At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.
Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.
No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.
Signed-off-by: Rich Felker <dalias@libc.org>
SH3/4 (with MMU) have a virtually indexed cache, requiring explicit
work to avoid consistency problems arising from having the same
physical address range cached in multiple cache lines. This is
unneeded for the NOMMU case, and some of the resulting code paths
(kmap_coherent) don't work. SH2 only avoided this problem by having a
4-way associative cache with way size equal to the page size (4k),
yielding no cache index bits outside of the page offset and thus no
aliases.
Signed-off-by: Rich Felker <dalias@libc.org>
The removal was not complete and left behind one reference to a
removed function in smp-shx3.c. For completeness, also remove
declarations for functions that were removed.
Fixes: 45624ac389 "sh: remove arch-specific localtimer and use generic one"
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rich Felker <dalias@libc.org>
Historically SH-2 Linux (and originally uClinux) used a syscall
calling convention incompatible with the established SH-3/4 Linux ABI.
This choice was made because the trap range used by the existing ABI,
0x10-0x17, overlaps with the hardware exception/interrupt trap range
reserved by SH-2, and in particular, with the SH-2A divide-by-zero and
division-overflow exceptions.
Despite the documented syscall convention using the low bits of the
trap number to signal the number of arguments the kernel should
expect, no version of the kernel has ever used this information, nor
is it useful; all of the registers need to be saved anyway. Therefore,
it is possible to pick a new trap number, 0x1f, that is both supported
by all existing SH-3/4 kernels and unassigned as a hardware trap in
the SH-2 range. This makes it possible to produce SH-2 application
binaries that are forwards-compatible with running on SH-3/4 kernels
and to treat SH as a unified platform with varying ISA support levels
rather than multiple gratuitously-incompatible platforms.
This patch adjusts the range checking SH-2 and SH-2A kernels make for
the syscall trap to accept the range 0x1f-0x2f rather than just
0x20-0x2f. As a result, trap 0x1f now acts as a syscall for all SH
models.
Signed-off-by: Rich Felker <dalias@libc.org>
The SCIF variant in the sh7734 SoC is not the common "SH-4(A)" variant,
but a derivative with added "Baud Rate Generator for External Clock"
(BRG). Correct the regtype value in platform data to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The sh-sci driver falls back to the peripheral clock if the sci_ick
clock doesn't exist. There's thus no need to create an alias for the
peripheral clock named sci_ick.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SCI driver requires a functional clock named "fck" and falls back to
"sci_ick" or "sci_fck" when the "fck" clock doesn't exist. To allow
removal of the fallback code rename the sci_ick and sci_fck clocks to
fck for all SH platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
Its return value is not used by the subsys core and nothing meaningful
can be done with it, even if we want to use it. The subsys device is
anyway getting removed.
Update prototype of ->remove_dev() to make its return type as void. Fix
all usage sites as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bitrot has set in for this driver and the sh-vou clock was never enabled,
since the clock name in clock-sh7724.c was wrong. It should be sh-vou, not
sh-vou.0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We have always had an efficient way of registering a table of clock
lookups - it's called clkdev_add_table(). However, some people seem
to really love writing inefficient and unnecessary code.
Convert SH to use the correct interface.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only place where the time is invalid is when the ACPI_CSTATE_FFH entry
method is not set. Otherwise for all the drivers, the time can be correctly
measured.
Instead of duplicating the CPUIDLE_FLAG_TIME_VALID flag in all the drivers
for all the states, just invert the logic by replacing it by the flag
CPUIDLE_FLAG_TIME_INVALID, hence we can set this flag only for the acpi idle
driver, remove the former flag from all the drivers and invert the logic with
this flag in the different governor.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Resources scif1_resources & scif2_resources overlap. Actual SCIF region
size is 0x10.
This is regression from commit d850acf975 ("sh: Declare SCIF register
base and IRQ as resources")
Signed-off-by: Andriy Skulysh <askulysh@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Fix the device name for the CMT.
Add clocks called usb0 and usb1 so that r8a66597_hcd works again on the
ecovec24 board
Signed-off-by: Daniel Palmer <danieruru@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MTU2 (Multi-Function Timer Pulse Unit 2) driver implements a new
style of platform data that handles the timer as a single device with
multiple channel. Switch from the old-style platform data to the
new-style platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The TMU (Timer Unit) driver implements a new style of platform data that
handles the timer as a single device with multiple channel. Switch from
the old-style platform data to the new-style platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CMT (Compare Match Timer) driver implements a new style of platform
data that handles the timer as a single device with multiple channel.
Switch from the old-style platform data to the new-style platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Switch the RSPI MSTP clock on SH7757 from a con ID match to a dev ID
match, so we can start looking it up using clk_get() with a NULL ID.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bcf24e1daa ("mmc: omap_hsmmc: use the generic config for
omap2plus devices"), enabled the build for other platforms for compile
testing.
sh-allmodconfig now fails with:
include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1
This happens because SuperH #defines "CCR", which is one of the enum
values in include/linux/omap-dma.h. There's a similar issue with "CCR2"
on sh2a.
As "CCR" and "CCR2" are too generic names for global #defines, prefix
them with "SH_" to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SCIFA ports on sh7723 and sh7724 seem to use a sampling rate of half the
value specified in the datasheet. This is currently handled by a custom
baud rate calculation algorithm. The algorithm ID will be removed from
platform data, set the sampling rate directly instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only a couple of arches (sh/x86) use fpu_counter in task_struct so it can
be moved out into ARCH specific thread_struct, reducing the size of
task_struct for other arches.
Compile tested sh defconfig + sh4-linux-gcc (4.6.3)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Paul Mundt <paul.mundt@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Commit 06a64f91da (SH7619: fix Ether support) has
a typo in the 'phy_interface' field name of the platform data which causes build
error -- fix it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'sh_eth' driver's probe will crash as the platform code is hopelessly behind
the platform data -- it passes PHY ID instead of 'struct sh_eth_plat_data *'.
Strangely, both commit d88a3ea6fa (SH7619 add ethernet controler support) that
added the platform code and commit 71557a37ad ([netdrvr] sh_eth: Add SH7619
support) were done in about the same time, yet the latter one added 'struct
sh_eth_plat_data' and the platform code didn't ever get updated...
Add the proper platform data and fix off-by-one memory resource end error, while
at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/sh/kernel/cpu/shmobile/cpuidle.c: In function 'sh_mobile_setup_cpuidle':
arch/sh/kernel/cpu/shmobile/cpuidle.c:102:2: error: too few arguments to function 'cpuidle_register'
include/linux/cpuidle.h:129:12: note: declared here
arch/sh/kernel/cpu/shmobile/cpuidle.c:94:6: warning: unused variable 'ret' [-Wunused-variable]
Add the missing parameter, and remove the unused variable.
Both introduced by commit b181a3b03f ("SH:
cpuidle: use init/exit common routine").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/sh uses of the __cpuinit macros from
all C files. Currently sh does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Get the SH7724 code/data in the driver out of #ifdef by adding "r8a7724-ether"
to the platform driver's ID table. Change the Ether platform device's name in
the SH platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH77{34|63} specific code/data in the driver out of #ifdef by adding
"sh7734-gether" and "sh7763-gether" to the platform driver's ID table. Note
that we have to split the 'struct sh_eth_cpu_data' instance into two due to
#ifdef inside it; note that we can kill the duplicate sh_eth_set_rate_gether().
Change the GEther platform device's name in the SH platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the SH7619 data in the driver out of #ifdef by adding "sh7619-ether" to the
platform driver's ID table. Change the Ether platform device's name in the SH
platform code accordingly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUYghoGCrR//JCVInAQIS0hAAoTaH/IgTmKMsKuP1fS/zhsXNSioO77GR
5KnEigaprC7JJK4k+Ahl6xVY/6/RmjWA3aLJ6eqBHHsupE1c5AOgDxIB78PtY8gn
vS+oKPqUlYi9bMJRp6LDsr23filt1Ri6woVYnW7htFsfXZIqxf+x6OlMKGULC4Zv
469rx/mgUB7IH/uwp8Jasr7xtE4hnjtgoUIqAKRmE10dLUTAuCN5+SABhlKMZIbl
W5VimdiDK6pNm2ENPcJQhTCMK1pFuChgrzpqOGSxsAiYIQgshuAuJJLb0RvEMppu
zuDQIxjfmJrwzytyGpxC4c9YVhNajppnWuenpAyaqaPuAi5sGkNFzdJ5NNWokZZ7
g6PfKLr9SAnuvfpTTX/JVuVYHysj18wEGVlLklLFDX8l9Bt6RZ17DARZ+4P8RLgN
0NI5j/IWwCesrsbS000NT7vi+mK/cWW22Z7oXa8aIQYPDod2aV5SxImmfXWx0xvf
vDOkzeNxJb5Tpp6WN1A715ZYdWfEuCJT3D6jX5Gsv6Ggri0+zwbsm/NglCCcqe0X
slO/74Kn9nknK85p5rm51KIaHvP4POPR/pZP9mQvDDKIqs3qQSjhBgozk0gWbara
Wg6k2yeRPxmdj+tsGQMxmT2iLWCWx/uhAilW83oOUiFtTPnC6HkBF5AdXXI08Yt8
/d19O715i/g=
=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
This is yet another driver change, which is split out just because
of its size. As already in 3.9, a lot of changes are going on here,
as the shmobile platform gets converted from its own pin control
API to the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRhKXTAAoJEIwa5zzehBx3Y0wQAKr5Bq6j3tcOF+1X59xXYdXC
mR8rDM2O5kyGtLwIVj1IpAKcg2vqduszvA4+S9RS50n7R8FYsYB6Mpl+gi8zCWDR
ZeWgvJZNkr9AXsiE4BGsOPKDPwPmPG+PeAsKYuxHw1xXRLTY3xxoUkxhmBoOUHxp
C7kP20K86QJMAx4D8oddL62j+bMBiQyS5jl7oZeNLm9dptdSh3mbH0XY7iDEJOA9
ReokPLEK6/lCIV/IVwHHESIltQ68ZhT1WTFjqcX4kP5v+xnbZwUmSE1cNgGb3+96
1Ufnn6seymsz3HzJbmDfMl3WPBQz//QLZN88bZECD+p1AIPWAvnzFY3UAXZiWKi9
SiFJgABPcsbHFvWLbP0mA9eTXctg6VG3JiaPcx74yihnih489cUT4eqYK8Nn4EZz
Mvp/QLSzhnlghZfOmIY3yyjx2I+uvGU+NBgU+tO2lubcg0xJHPCxXgdDE85dMhIi
MCMTSJRtTbY2vuow5u5KGAi+2wpQXm7p7X3w0pxKnd0tRpTfpSiWwkSSedl8r7kZ
OaUttt4XPVNZ/NpVAg9yb+45opmHS45ge5DcxG5YYktCWQr9Xy8A3ueMmv2EnPtP
8gvSis4AP47ugQATzjNxaRN2HhuW3dsn/+WBUOlOoVwdI/mU0cGiOmY0n90PVZs7
QH9tasnWBX9m98Qj05LG
=9DPk
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC pinctrl changes for Renesas from Olof Johansson:
"This is yet another driver change, which is split out just because of
its size. As already in 3.9, a lot of changes are going on here, as
the shmobile platform gets converted from its own pin control API to
the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well"
* tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (142 commits)
ARM: shmobile: r8a7779: Remove INTC function GPIOs
ARM: shmobile: r8a7779: Remove LBSC function GPIOs
ARM: shmobile: r8a7779: Remove USB function GPIOs
ARM: shmobile: r8a7779: Remove HSPI function GPIOs
ARM: shmobile: r8a7779: Remove SCIF function GPIOs
ARM: shmobile: r8a7779: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7779: Remove DU function GPIOs
ARM: shmobile: r8a7779: Remove DU1_DOTCLKOUT1 GPIO
ARM: shmobile: r8a7740: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7740: Remove LCD0 and LCD1 function GPIOs
ARM: shmobile: sh73a0: Remove IrDA function GPIOs
ARM: shmobile: sh73a0: Remove USB function GPIOs
ARM: shmobile: sh73a0: Remove BSC function GPIOs
ARM: shmobile: sh73a0: Remove KEYSC function GPIOs
ARM: shmobile: sh73a0: Remove pull-up function GPIOS
ARM: shmobile: sh73a0: Remove FSI function GPIOs
ARM: shmobile: sh73a0: Remove I2C function GPIOs
ARM: shmobile: sh73a0: Remove SCIFA and SCIFB function GPIOs
ARM: shmobile: sh73a0: Remove LCDC and LCDC2 function GPIOs
ARM: shmobile: sh7372: Remove SDHI and MMCIF function GPIOs
...
Remove the duplicated code and use the cpuidle common code for initialization.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The en_core_tk_irqen flag is set in all the cpuidle driver which
means it is not necessary to specify this flag.
Remove the flag and the code related to it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org> # for mach-omap2/*
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Registering the driver, or the device, can fail, let's check the return code
and return the error code to the PM layer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Like all the other drivers, let's initialize the structure a compile time
instead of init time.
The states #1 and #2 are not enabled by default. The init function will
check the features of the board in order to enable the state.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CPUIDLE_DRIVER_STATE_START constant is only set when the kernel compilation
option CONFIG_ARCH_HAS_CPU_RELAX is set, but this is only relatated to x86, so
it is always zero.
Remove the reference to this constant in the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
