Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.
Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch removes a set but unused variable in hcd.c.
Fixes gcc warning:
variable ‘data_fifo’ set but not used [-Wunused-but-set-variable]
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----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=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b135055 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)"). That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off. Hopefully
it's because someone copied it from other parameters and didn't think
to try it?
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Amlogic since commit f94310ac07
("usb: dwc2: add support for Meson8b and GXBB SoCs"). While this was
after most of the recent improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on HiSilicon since commit
37dd9d65cc ("usb: dwc2: add support of hi6220"). Since then there
have been many many improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Broadcom since commit
58b179dcf2 ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b048 ("usb: dwc2: host: Totally redo the microframe
scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To start ISOC transfers in handlers dwc2_gadget_handle_nak() and
dwc2_gadget_handle_out_token_ep_disabled() driver reads current frame
number, based on which, set target frame number to start first ISOC
transfer.
In case if system's high IRQ latency and multiple EP's asserted
interrupt in same frame, there are high probability that when reading
current frame number in EP's handlers, actual frame number can be
increased. As result for bInterval > 1, starting target frame
will be set wrongly and all ISOC packets will be dropped.
In patch "usb: dwc2: Change reading of current frame number flow"
reading of current frame number done ASAP in common interrupt handler.
This frame number stored in frame_number variable which used as
starting frame number for ISOC EP's in above mentioned handlers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.
Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dwc2_readl/writel functions after hsotg declaration for
adding hsotg structure to dwc2_readl/writel function prototypes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Taken directly from commit 0efd937e27 ("USB: ehci-tegra: fix inefficient
copy of unaligned buffers")
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM)
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For unidirectional endpoints, the endpoint pointer will be NULL for the
unused direction. Check that the endpoint is active before
dereferencing this pointer.
Fixes: 1b4977c793 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_in() function")
Fixes: 689efb2619 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_out() function")
Fixes: d84845522d ("usb: dwc2: Update GINTSTS_GOUTNAKEFF interrupt handling")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling split transactions we will try to delay retry after
getting a NAK from the device. This works well for BULK transfers that
can be polled for essentially forever. Unfortunately, on slower systems
at boot time, when the kernel is busy enumerating all the devices (USB
or not), we issue a bunch of control requests (reading device
descriptors, etc). If we get a NAK for the IN part of the control
request and delay retry for too long (because the system is busy), we
may confuse the device when we finally get to reissue SSPLIT/CSPLIT IN
and the device will respond with STALL. As a result we end up with
failure to get device descriptor and will fail to enumerate the device:
[ 3.428801] usb 2-1.2.1: new full-speed USB device number 9 using dwc2
[ 3.508576] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.699150] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.891653] usb 2-1.2.1: new full-speed USB device number 10 using dwc2
[ 3.968859] usb 2-1.2.1: device descriptor read/8, error -32
...
Let's not delay retries of split CONTROL IN transfers, as this allows us
to reliably enumerate devices at boot time.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Freed allocated request for ep0 to prevent memory leak in case when
dwc2_driver_probe() failed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048 ("usb: dwc2: host: Totally redo the microframe scheduler")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC OUT transfer, when the OUT token received while EP disabled,
we shouldn't complete a usb request. The current flow completed one
usb request, this will lead to a packet drop to function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC transfer, when the NAK interrupt happens, we shouldn't complete
a usb request, the current flow will complete one usb request with no
hardware transfer, this will lead to a packet drop on the usb bus.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of requests queue is empty reset EP target_frame to
initial value.
This allow restarting ISOC traffic in case when function
driver queued requests with interruptions.
Tested-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.
Converting ._param to int to avoid this warning.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 4.17-rc, commit 03ea6d6e9e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.
Unplugging the OTG port would result in:
[ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers
And the USB-host ports would not function.
And plugging in the OTG port, we would see:
[ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[ 46.055767] Hardware name: HiKey Development Board (DT)
[ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...
Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.
Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current frame_number is read from core for both
device and host modes. Reading of the current frame
number needs to be performed ASAP due to IRQ latency's.
This is why, it is moved to common interrupt handler.
Accordingly updated dwc2_gadget_target_frame_elapsed()
function which uses stored frame_number instead of
reading frame number.
In cases when target frame value is incremented
the frame_number is required to read again.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Dumping the registers via debugfs makes USB on Raspberry Pi completely
unusable. The read of register GRXSTSP ("Receive Status Read and Pop
Register") is responsible for this behaviour, because it pops the RX FIFO.
So avoid this by omitting the relevant register.
CC: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Fixes: 563cf017c4 ("usb: dwc2: debugfs: add support for complete register dump")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Crash caused by going out of "eps_out" array range.
Iteration on "eps_out" changed to less than "num_of_eps".
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.
Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode required to enable BNA interrupt for
both directions.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed existing two descriptor-chain flow to one chain.
In two-chain implementation BNA interrupt used for switching between
two chains. BNA interrupt asserted because of returning to
beginning of the chain based on L-bit of last descriptor.
Because of that we lose packets. This issue resolved by using one
desc-chain.
Removed all staff related to two desc-chain flow from
DDMA ISOC related functions.
Removed request length checking from dwc2_gadget_fill_isoc_desc()
function. Request length checking added to dwc2_hsotg_ep_queue()
function. If request length greater than descriptor limits then
request not added to queue. Additional checking done for High
Bandwidth ISOC OUT's which not supported by driver. In
dwc2_gadget_fill_isoc_desc() function also checked desc-chain
status (full or not) to avoid of reusing not yet processed
descriptors.
In dwc2_gadget_start_isoc_ddma() function creation of desc-chain
always started from descriptor 0. Before filling descriptors, they
were initialized by HOST BUSY status.
In dwc2_gadget_complete_isoc_request_ddma() added checking for
desc-chain rollover. Also added checking completion status.
Request completed successfully if DEV_DMA_STS is DEV_DMA_STS_SUCC,
otherwise complete with actual=0. For systems with high IRQ latency
added pointer compl_desc to next descriptor to be completed by
XferCompl interrupt. This pointer replace descriptor index calculation
based on DxEPDMA register. On descriptor completion interrupt
processing all descriptors starting from compl_desc till descriptor
which Buffer Status field not equal DMA_DONE status.
Actually removed dwc2_gadget_start_next_isoc_ddma() function because
now driver use only one desc-chain and instead that function added
dwc2_gadget_handle_isoc_bna() function for handling BNA interrupts.
Handling BNA interrupt done by flushing TxFIFOs for OUT EPs,
completing request with actual=0 and resetting desc-chain number and
target frame to initial values for restarting transfers.
On handling NAK request completed with actual=0. Incremented target
frame to allow fill desc chain and start transfers.
In DDMA mode avoided of frame number incrementing, because tracking
of frame number performed in dwc2_gadget_fill_isoc_desc() function.
When core assert XferCompl along with BNA, we should ignore XferCompl
in dwc2_hsotg_epint() function.
On BNA interrupt replaced dwc2_gadget_start_next_isoc_ddma() by above
mentioned BNA handler.
In dwc2_hsotg_ep_enable() function added sanity check of bInterval
for ISOC IN in DDMA mode, because HW doesn't supported EP's with
bInterval more than 10 and check for mc for ISOC OUT transfers,
because core doesn't support high bandwidth transfers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
-----BEGIN PGP SIGNATURE-----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=F6OC
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.17 merge window
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
Trivial fix to spelling mistake in dev_warn warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
