Some Ethernet PHYs/switches such as Broadcom's BCM53125 have a hardware
bug which makes them not release the MDIO line during turn-around time.
This gets flagged by the GENET MDIO controller as a read failure, and we
fail the read transaction.
Check the MDIO bus phy_ignore_ta_mask bitmask for the PHY we are reading
from and if it is listed in this bitmask, ignore the read failure and
proceed with returning the data we read out of the controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY IDs for Davicom DM9161B and DM9161C variants.
Tested with a DM9161C on a custom Atmel-based SAM9X25 board in RMII
mode.
The DM9161B uses the same model id with just the LSB bit of the version
id changing (which is masked out).
For all intents and purposes they're the same as the DM9161A with an
added GPSI mode and better fabrication process.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB device includes the gPTP timer, so we can implement a PTP clock
driver. We're doing that in a separate file, with the main Ethernet driver
calling the PTP driver's [de]initialization and interrupt handler functions.
Unfortunately, the clock seems tightly coupled with the AVB-DMAC, so when that
one leaves the operation mode, we have to unregister the PTP clock... :-(
Based on the original patches by Masaru Nagai.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB includes an Gigabit Ethernet controller (E-MAC) that is basically
compatible with SuperH Gigabit Ethernet E-MAC. Ethernet AVB has a dedicated
direct memory access controller (AVB-DMAC) that is a new design compared to the
SuperH E-DMAC. The AVB-DMAC is compliant with 3 standards formulated for IEEE
802.1BA: IEEE 802.1AS timing and synchronization protocol, IEEE 802.1Qav real-
time transfer, and the IEEE 802.1Qat stream reservation protocol.
The driver only supports device tree probing, so the binding document is
included in this patch.
Based on the original patches by Mitsuhiro Kimura.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIA Delay-Gradient (CDG) is a TCP congestion control that modifies
the TCP sender in order to [1]:
o Use the delay gradient as a congestion signal.
o Back off with an average probability that is independent of the RTT.
o Coexist with flows that use loss-based congestion control, i.e.,
flows that are unresponsive to the delay signal.
o Tolerate packet loss unrelated to congestion. (Disabled by default.)
Its FreeBSD implementation was presented for the ICCRG in July 2012;
slides are available at http://www.ietf.org/proceedings/84/iccrg.html
Running the experiment scenarios in [1] suggests that our implementation
achieves more goodput compared with FreeBSD 10.0 senders, although it also
causes more queueing delay for a given backoff factor.
The loss tolerance heuristic is disabled by default due to safety concerns
for its use in the Internet [2, p. 45-46].
We use a variant of the Hybrid Slow start algorithm in tcp_cubic to reduce
the probability of slow start overshoot.
[1] D.A. Hayes and G. Armitage. "Revisiting TCP congestion control using
delay gradients." In Networking 2011, pages 328-341. Springer, 2011.
[2] K.K. Jonassen. "Implementing CAIA Delay-Gradient in Linux."
MSc thesis. Department of Informatics, University of Oslo, 2015.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming tcp_cdg uses tcp_enter_cwr() to initiate PRR. Export this
function so that CDG can be compiled as a module.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_SWITCHDEV is enabled, but port driver does not implement
support for IPv4 FIB add/del ops, don't fail route add/del offload
operations. Route adds will not be marked as OFFLOAD. Routes will be
installed in the kernel FIB, as usual.
This was report/fixed by Florian when testing DSA driver with net-next on
devices with L2 offload support but no L3 offload support. What he reported
was an initial route installed from DHCP client would fail (route not
installed to kernel FIB). This was triggering the setting of
ipv4.fib_offload_disabled, which would disable route offloading after the
first failure. So subsequent attempts to install the route would succeed.
There is follow-on work/discussion to address the handling of route install
failures, but for now, let's differentiate between no support and failed
support.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: broadcom: define pseudo-PHY address
This patch series converts existing in-tree users of the Broadcom pseudo-PHY
address (30) used to configure MDIO-connected switches to share a constant in a
shared header files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the newly introduced BRCM_PSEUDO_PHY_ADDR constant from
brcmphy.h instead of open-coding the Broadcom Ethernet switches
pseudo-PHY address (30).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What BGMAC defines as BGMAC_PHY_NOREGS is in fact the Broadcom Ethernet
switches' pseudo-PHY address (30), utilize the newly introduced constant
from brcmphy.h
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What B44 has been locally using as B44_PHY_ADDR_NO_LOCAL_PHY is in fact
the Broadcom Ethernet switches pseudo-PHY address (30). Update the
header to use the newly introduced constant and update comments so they
are within 80 columns and consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the pseudo-PHY address (30) which is used by all Broadcom
Ethernet switches in a shared header file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We utilize inline functions from the PHY library, make sure that we do
include phy.h in brcmphy.h in order for the code including brcmphy.h not
to have to resolve this inclusion dependency.
Fixes: 705314797b ("net: phy: broadcom: move shadow 0x1C register accessors to brcmphy.h")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dctcp_alpha can be read by from dctcp_get_info() without
synchro, so use WRITE_ONCE() to prevent compiler from using
dctcp_alpha as a temporary variable.
Also, playing with small dctcp_shift_g (like 1), can expose
an overflow with 32bit values shifted 9 times before divide.
Use an u64 field to avoid this problem, and perform the divide
only if acked_bytes_ecn is not zero.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
-----BEGIN PGP SIGNATURE-----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=2wTw
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For this round we mostly have fixes:
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SCM_SECURITY was originally only implemented for datagram sockets,
not for stream sockets. However, SCM_CREDENTIALS is supported on
Unix stream sockets. For consistency, implement Unix stream support
for SCM_SECURITY as well. Also clean up the existing code and get
rid of the superfluous UNIXSID macro.
Motivated by https://bugzilla.redhat.com/show_bug.cgi?id=1224211,
where systemd was using SCM_CREDENTIALS and assumed wrongly that
SCM_SECURITY was also supported on Unix stream sockets.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, a;
@@
-init_timer(&e1);
+setup_timer(&e1, a, 0UL);
... when != a = e2
-e1.function = a;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch V8 adds support for Cavium Liquidio pci express
based 10Gig ethernet adapters.
1) Consolidated all debug macros to either call dev_* or
netdev_* macros directly, feedback from previous patch.
2) Changed soft commands to avoid crash when running
in interrupt context.
3) Fixed link status not reflecting correct status when NetworkManager
is running. Added MODULE_FIRMWARE declarations.
Following were the previous patches.
Patch V7:
1) Minor comments from v6 release regarding debug statements.
2) Fix for large multicast lists.
3) Fixed lockup issue if port initialization fails.
4) Enabled MSI by default.
https://patchwork.ozlabs.org/patch/464441/
Patch V6:
1) Addressed the uint64 vs u64 issue, feedback from previous patch.
2) Consolidated some receive processing routines.
3) Removed link status polling method.
https://patchwork.ozlabs.org/patch/459514/
Patch V5:
Based on the feedback from earlier patches with regards to
consolidation of common functions like device init, register
programming for cn66xx and cn68xx devices.
https://patchwork.ozlabs.org/patch/438979/
Patch V4:
Following were the changes based on the feedback from earlier patch:
1) Added mmiowb while synchronizing queue updates and other hw
interactions.
2) Statistics will now be incremented non-atomically per each ring.
liquidio_get_stats will add stats of each ring while reporting the
total statistics counts.
3) Modified liquidio_ioctl to return proper return codes.
4) Modified device naming to use standard Ethernet naming.
5) Global function names in the driver will have lio_/liquidio_/octeon_
prefix.
6) Ethtool related changes for:
Removed redundant stats and jiffies.
Use default ethtool handler of link status.
Speed setting will make use of ethtool_cmd_speed_set.
7) Added checks for pci_map_* return codes.
8) Check for signals while waiting in interruptible mode
https://patchwork.ozlabs.org/patch/435073/
Patch v3:
Implemented feedback from previous patch like:
Removed NAPI Config and DEBUG config options, added BQL and xmit_more
support.
https://patchwork.ozlabs.org/patch/422749/
Patch V2:
Implemented feedback from previous patch.
https://patchwork.ozlabs.org/patch/413539/
First Patch:
https://patchwork.ozlabs.org/patch/412946/
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Robert Richter <Robert.Richter@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <Aleksey.Makarov@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-09
This series contains updates to ixgbe only.
The series adds additional support for x550 support, such as WoL and
auto-negotiation of flow control. Adds new PHY support (external PHY)
for x550, as well as the new methods/functions needed to support the new
PHY's. Fixed a bug found in code inspection, where a check was missed
when clearing counters for x550. Also fixed the init code flow for copper
x550 devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
Add cim_ma_la, cim_pif_la and tx_rate debugfs entry
This patch series adds the following.
Add debugfs entry to dump CIM MA logic analyzer and CIM PIF logic analyzer logs.
Also adds support to dump tx rate of the channels in the adapter
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
EXTRA_CFLAGS should be used on the command line only.
Since EXTRA_CFLAGS here add only a non-existant path to compiler
include paths (by -I), remove EXTRA_CFLAGS completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the user-specified bridge port was ignored when
deleting an fdb entry and thus one could delete an entry that belonged
to any port.
Example (eth0 and eth1 are br0 ports):
bridge fdb add 00:11:22:33:44:55 dev eth0 master
bridge fdb del 00:11:22:33:44:55 dev eth1 master
(succeeds)
after the patch:
bridge fdb add 00:11:22:33:44:55 dev eth0 master
bridge fdb del 00:11:22:33:44:55 dev eth1 master
RTNETLINK answers: No such file or directory
Based on a patch by Wilson Kok.
Reported-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVdphLAAoJEP5prqPJtc/HZR0H/j7+UFxotHs+ummTanP3Rbqi
lLBgjzXQDvQeEYhCHzUM4s0dKOQp3arHnO538hB5bONijxoNJkHBkz0urbspLR/f
i9BZRdLd8eiCrXYo4zXM1dZ4xA/xLKX/4sZU/r44wZlcQeLR0VwerZWWd3Zl9hi5
0RGWvENz2FajCxBHaf+TFbr6AVPg7ikWXRpk3s5//adfGYzZMLTpIecrOI3OdtB2
JYrX1FZW2NudtzNfC5vR7g8x4esGzTL7TupdNP0SpxYUTfAkEbLrG+VCbswkYVCs
TL7BElbz5JrfUweWjj/6LJKPFUlCHW3TygBbmHiIl7htyJPllCIpF2gDI+uhSYw=
=JtLU
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.2-20150609' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-05-06
this is a pull request of a two patches for net-next.
The first patch is by Tomas Krcka, he fixes the (currently unused)
register address for acceptance filters. Oliver Hartkopp contributes a
patch for the cangw, where an optional UID is added to reference
routing jobs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes a bug in hwmp_preq_frame_process where the wrong metric
can be used when forwarding a PREQ. This happens because the code uses
the same metric variable to record the value of the metric to the source
of the PREQ and the value of the metric to the target of the PREQ.
This comes into play when both reply and forward are set which happens
when IEEE80211_PREQ_PROACTIVE_PREP_FLAG is set and when MP_F_DO | MP_F_RF
is set. The original code had a special case to handle the first case
but not the second.
The patch uses distinct variables for the two metrics which makes the
code flow much clearer and removes the need to restore the original
value of metric when forwarding.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- use common Jenkins hash instead of private implementation
- extend internal routing API
- properly re-arrange header files inclusion
- clarify precedence between '&' and '?'
- remove unused ethhdr variable in batadv_gw_dhcp_recipient_get()
- ensure per-VLAN structs are updated upon MAC change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVdaxwAAoJEOb/4TMchkvffJsQAK33RTmcnFYVpS09AywTbxfC
kNo5SAbQJ1MsNui8TmyHsnLBW/l59WnP8CITVYDlwLyW4cEKWVooGsFPv+MCityM
3vOqghdi7jC1b0LT6kTcoSr7P04q+bBV9atj5Z5nnXUpvjmW0b/a6qCIZmqGKTtQ
WIIayEs0bVPJ6y1Z6CDpFQY6k9j938BaH3VgP7NL4zXRA3OJGGQKaZTRwVuYnVu4
Swt/zj+B7lutBSP2d4ngjU2CXS35OzDWl4GybQuIiNzdSXsZwm4inTyuNjA4Eqdg
vE87ZqbFqD4T2PqR1wcTPKMJegd+nPQrYDdeNfz91KdjVKBN+LrdSCX3IozEynpY
7584+eROCyCKlQGi7OcRze5THbZ+BNKxUd3Ds4ek2NTU7vG2rMWADFj3wZ0yzX6F
e/JunQ39BHXPSc6UlaTgdYiVpTNME9+A2I0AXMOpU6urpc4fAyFVGUORJqjM8BBm
jLZ8QakmXdfgBYi7zqefeCW9de9L1ekGQs/XB1AmKmx5xY7IKzKEZbkUV3nAxtqI
YKP2yQUhqjoke6bzllz72CPChO4O11fYPCDPL0sarn/UxY8SzwmHeKi8UeGaN6gt
FZhR17kQGm4c2WF7082HEIrOW137YogEOFWMixqpqix5ICBmmRMPqo8wqQBxllk3
mC+4jiwdn4kT1EVAqHba
=u+G3
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- use common Jenkins hash instead of private implementation
- extend internal routing API
- properly re-arrange header files inclusion
- clarify precedence between '&' and '?'
- remove unused ethhdr variable in batadv_gw_dhcp_recipient_get()
- ensure per-VLAN structs are updated upon MAC change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug in ixgbe_setup_ixfi_x550em where we were
reading and modifying IXGBE_KRM_LINK_CTRL_1 but forgot to write the
results back.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though X550 may later clear this value for certain devices
set it initially to support copper.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to call the set_lan_id before accessing I2C and this wasn't
being done so this patch corrects that. Likewise we do the same for
QSFP just to be consistent.
In the X550 case this is even more important as with out it the mux
is not controlled properly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds ixgbe_check_link_t_X550em for checking copper PHY
link. We check that both the MAC and external PHY have link. This
is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for another 10baseT X550 device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A subset of the X550 function pointers didn't have default methods. This
didn't cause any issue with previous X550 devices as they were all
redefined. However future devices will need these default values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewing the X550 copper init flow with the Si team resulted in a
new simplified flow. We no longer wait for the PHY FW initialization
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be un-stalled
low-power mode or enabled the transceiver
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This check was missed in when this new MAC type was added. Since
these counts can be incremented for X550 we need to clear them.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices. This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for receiving interrupts from a external copper
PHY for the X550 part. This includes enabling, detection as well as
re-enablement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases. This patch pulls the text from the
same location. I noticed this as I am about to add another case.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a PHY reset function ixgbe_reset_phy_t_X550em. Which
allows devices that have LASI support in enable their interrupt.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds x550 external PHY interrupt and forced 1G/10G support.
This included enabling and handling LSC and thermal sensor interrupt.
ixgbe_handle_lasi() has been added for handling the interrupts received
over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em
and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable
mask and check interrupt flags for the external PHY.
Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em.
ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY
to either iXFI (10G) or KX (1G) based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. Combine
all this functionality in to a support function.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This new method will control the PHY power state. You pass in the
state you wish to change to (ether on or off). For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a define for the new PHY identification as well as it's mapping
to the correct PHY type. Also allow ethtool to identify this type
as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom. This patch enables
these devices this support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values. These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In mesh mode there is a race between establishing links and processing
rates and capabilities in beacons. This is very noticeable with slow
beacons (e.g. beacon intervals of 1s) and manifested for us as stations
using minstrel when minstrel_ht should be used. Fixed by changing
mesh_sta_info_init so that it always checks rates and such if it has not
already done so.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa counter has moved from sdata to beacon/presp but
it is not updated accordingly for mesh and ibss. Fix this.
Fixes: af296bdb8d ("mac80211: move csa counters from sdata to beacon/presp")
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
