Fixes: a0ee354148 ("sfc: process RX event inner checksum flags")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and
GENEVE UDP ports. Also reset the port list to empty on driver load and
on driver unload, with appropriate flag set on the unload case.
These port numbers are used for RX inner checksum offload, and in future
will also be used for TX inner checksum offload and encapsulated TSO.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function wasn't being called in this particular case when the MC
reboots. This caused resource reallocations to not be handled properly
and often ended up disabling the interface.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mainly to prepare for a future overlay networking patch that
could cause an MC reset at probe time if the UDP tunnel port list is
set immediately upon driver load.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the csum_level for encapsulated packets where the encapsulation
type, l3 class and l4 class are sets that need it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload of encapsulated packets. This
essentially just means paying attention to the inner checksum flags
in the RX event, and if *either* checksum flag indicates a fail then
don't tell the kernel that checksum offload was successful.
Also, count these checksum errors and export the counts to ethtool -S.
Test the most common "good" case of RX events with a single bitmask
instead of a series of ifs. Move the more specific error checking
in to a separate function for clarity, and don't use unlikely() there
since we know at least one of the bits is bad.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is harmless because it's just a sanity check and we always
pass valid values for "encap_type" but the test is off by one.
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 364b605573 ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of tricky code, we also remove
one lock operation in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of tricky code, we also remove
one lock operation in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
encap_type should be checked to see if it is greater or equal to
the size of array map to fix an off-by-one array size check. This
fixes an array overrun read as detected by static analysis by
CoverityScan, CID#1398883 ("Out-of-bounds-read")
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
based on inner fields, and when the NIC recognises such traffic, it
does not match unencapsulated traffic filters any more. So add catch-
all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
will not occur until the driver (on the primary PF) notifies the
firmware of UDP ports to use, NVGRE will always be recognised, hence
without this patch 8000 series adapters will drop all NVGRE traffic.
Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationalise several debug-or-warnings printks using netif_cond_dbg
to make output more consistent.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NIC is switched from full-featured to low-latency, encapsulated
filters are no longer available, and this causes errors. This patch
removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
insert when restoring filters, were UC, MC or broadcast default
filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensures that we report the key and indirection table the NIC is using,
rather than (if setting them failed earlier) what we wanted it to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8000 series SFC NICs have 4K PIO buffers, rather than the 2K of
the 7000 series. Rather than having a hard-coded PIO buffer size
(ER_DZ_TX_PIOBUF_SIZE), read it from the GET_CAPABILITIES_V2 MCDI
response.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an option descriptor has been sent on a queue but not followed by a
packet, there will have been no completion event, so the read and write
counts won't match and we'll think we can't do PIO. This combines with
the fact that we have two TX queues (for en/disable checksum offload),
and that both must be empty for PIO to happen.
This patch adds a separate "packet_write_count" that tracks the most
recent write_count we expect to see a completion event for; this excludes
option descriptors but _includes_ PIO descriptors (even though they look
like option descriptors). This is then used, rather than write_count,
in efx_nic_tx_is_empty().
We only bother to maintain packet_write_count on EF10, since on Siena
(a) there are no option descriptors and it always equals write_count, and
(b) there's no PIO, so we don't need it anyway.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero which makes the code clearer and also add header
file linux/etherdevice.h
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/sfc/efx.c:2337:5: warning:
symbol 'efx_get_phys_port_id' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev_port changes the device names allocated by systemd. Any devices
with a dev_port >0 will (in default distro configurations) have a suffix of
"d<port-number>" appended.
This is not something done by other drivers, and causes confusion for users.
Fixes: 8be41320f3 ("sfc: Add code to export port_num in netdev->dev_port")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output is of the form p<port-number>.
Note that the port numbers don't necessarily map one-to-one to physical
cages, partly because of 4x10G port modes on QSFP+ and partly because
of hw/fw implementation details.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no good reason why this should be an SRIOV-only thing.
Thus, also move it out of SRIOV-specific files.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to set up RSS on EF10 (e.g. because firmware declared
RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
no fields, rather than confusingly reporting what fields we _would_ be
hashing on if RSS was working.
Fixes: dcb4123cbe ("sfc: disable RSS when unsupported")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
there are two drivers for Solarflare devices, but both still show up
directly beneath "Ethernet driver support" in the Kconfig. Follow the
pattern of other vendors and group them beneath an own vendor Kconfig
entry for Solarflare.
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should
only be used if it is not possible to continue without potential harm;
and since the non-DEBUG driver will continue regardless (as the BUG_ON is
compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver.
So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID
or the newly defined EFX_WARN_ON_ONCE_PARANOID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's no longer used now that Falcon is gone.
Also remove a reference in a comment to an ioctl that doesn't exist.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Easy enough for Falcon users to enable it when making oldconfig.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defalconisation removed one of the string arguments, but missed the
corresponding %s.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use ->heap_buf after commit 46d1efd852 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It gives no advantage over GSO now that xmit_more exists. If we find
ourselves unable to handle a TSO skb (because our TXQ doesn't have a
TSOv2 context and the NIC doesn't support TSOv1), hand it back to GSO.
Also do that if the TSO handler fails with EINVAL for any other reason.
As Falcon-architecture NICs don't support any firmware-assisted TSO,
they no longer advertise TSO feature flags at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to init the TXQ because of insufficient TSOv2 contexts,
try again with TSOv2 disabled.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for FATSOv2 to the driver. FATSOv2 offloads far more of the task
of TCP segmentation to the firmware, such that we now just pass a single
super-packet to the NIC. This means TSO has a great deal in common with a
normal DMA transmit, apart from adding a couple of option descriptors.
NIC-specific checks have been moved off the fast path and in to
initialisation where possible.
This also moves FATSOv1/SWTSO to a new file (tx_tso.c). The end of transmit
and some error handling is now outside TSO, since it is common with other
code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to break the hard dependency between the PTP clock subsystem and
ethernet drivers capable of being clock providers, this patch provides
simple PTP stub functions to allow linkage of those drivers into the
kernel even when the PTP subsystem is configured out. Drivers must be
ready to accept NULL from ptp_clock_register() in that case.
And to make it possible for PTP to be configured out, the select statement
in those driver's Kconfig menu entries is converted to the new "imply"
statement. This way the PTP subsystem may have Kconfig dependencies of
its own, such as POSIX_TIMERS, without having to make those ethernet
drivers unavailable if POSIX timers are cconfigured out. And when support
for POSIX timers is selected again then the default config option for PTP
clock support will automatically be adjusted accordingly.
The pch_gbe driver is a bit special as it relies on extra code in
drivers/ptp/ptp_pch.c. Therefore we let the make process descend into
drivers/ptp/ even if PTP_1588_CLOCK is unselected.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Link: http://lkml.kernel.org/r/1478841010-28605-4-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
