commit 08c27f3322fec11950b8f1384aa0f3b11d028528 upstream.
KMSAN found uninitialized value at batadv_tt_prepare_tvlv_local_data()
[1], for commit ced72933a5 ("batman-adv: use CRC32C instead of CRC16
in TT code") inserted 'reserved' field into "struct batadv_tvlv_tt_data"
and commit 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN
specific") moved that field to "struct batadv_tvlv_tt_vlan_data" but left
that field uninitialized.
[1] https://syzkaller.appspot.com/bug?id=07f3e6dba96f0eb3cabab986adcd8a58b9bdbe9d
Reported-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com>
Tested-by: syzbot <syzbot+50ee810676e6a089487b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: ced72933a5 ("batman-adv: use CRC32C instead of CRC16 in TT code")
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26c56ae67fa9fbb45a8a232dcd7ebaa7af16086 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d473d32c2fbac2d1d7082c61899cfebd34eb267a upstream.
[<vendor>,]nr-gpios property is used by some GPIO drivers[0] to indicate
the number of GPIOs present on a system, not define a GPIO. nr-gpios is
not configured by #gpio-cells and can't be parsed along with other
"*-gpios" properties.
nr-gpios without the "<vendor>," prefix is not allowed by the DT
spec[1], so only add exception for the ",nr-gpios" suffix and let the
error message continue being printed for non-compliant implementations.
[0] nr-gpios is referenced in Documentation/devicetree/bindings/gpio:
- gpio-adnp.txt
- gpio-xgene-sb.txt
- gpio-xlp.txt
- snps,dw-apb-gpio.yaml
[1] Link: cb53a16a1e/schemas/gpio/gpio-consumer.yaml (L20)
Fixes errors such as:
OF: /palmbus@300000/gpio@600: could not find phandle
Fixes: 7f00be96f1 ("of: property: Add device link support for interrupt-parent, dmas and -gpio(s)")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Saravana Kannan <saravanak@google.com>
Cc: stable@vger.kernel.org # v5.5+
Link: https://lore.kernel.org/r/20210405222540.18145-1-ilya.lipnitskiy@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63cf32389925e234d166fb1a336b46de7f846003 upstream.
The member 'tx_lpi_timer' is defined with __u32 datatype in the ethtool
header file. Hence, we should use ethnl_update_u32() in set_eee ops.
Fixes: fd77be7bd4 ("ethtool: set EEE settings with EEE_SET request")
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df41872b68601059dd4a84858952dcae58acd331 upstream.
I encountered a hung task issue, but not a performance one. I run DIO
on a device (need lba continuous, for example open channel ssd), maybe
hungtask in below case:
DIO: Checkpoint:
get addr A(at boundary), merge into BIO,
no submit because boundary missing
flush dirty data(get addr A+1), wait IO(A+1)
writeback timeout, because DIO(A) didn't submit
get addr A+2 fail, because checkpoint is doing
dio_send_cur_page() may clear sdio->boundary, so prevent it from missing
a boundary.
Link: https://lkml.kernel.org/r/20210322042253.38312-1-jack.qiu@huawei.com
Fixes: b1058b9812 ("direct-io: submit bio after boundary buffer is added to it")
Signed-off-by: Jack Qiu <jack.qiu@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90bd070aae6c4fb5d302f9c4b9c88be60c8197ec upstream.
The following deadlock is detected:
truncate -> setattr path is waiting for pending direct IO to be done (inode->i_dio_count become zero) with inode->i_rwsem held (down_write).
PID: 14827 TASK: ffff881686a9af80 CPU: 20 COMMAND: "ora_p005_hrltd9"
#0 __schedule at ffffffff818667cc
#1 schedule at ffffffff81866de6
#2 inode_dio_wait at ffffffff812a2d04
#3 ocfs2_setattr at ffffffffc05f322e [ocfs2]
#4 notify_change at ffffffff812a5a09
#5 do_truncate at ffffffff812808f5
#6 do_sys_ftruncate.constprop.18 at ffffffff81280cf2
#7 sys_ftruncate at ffffffff81280d8e
#8 do_syscall_64 at ffffffff81003949
#9 entry_SYSCALL_64_after_hwframe at ffffffff81a001ad
dio completion path is going to complete one direct IO (decrement
inode->i_dio_count), but before that it hung at locking inode->i_rwsem:
#0 __schedule+700 at ffffffff818667cc
#1 schedule+54 at ffffffff81866de6
#2 rwsem_down_write_failed+536 at ffffffff8186aa28
#3 call_rwsem_down_write_failed+23 at ffffffff8185a1b7
#4 down_write+45 at ffffffff81869c9d
#5 ocfs2_dio_end_io_write+180 at ffffffffc05d5444 [ocfs2]
#6 ocfs2_dio_end_io+85 at ffffffffc05d5a85 [ocfs2]
#7 dio_complete+140 at ffffffff812c873c
#8 dio_aio_complete_work+25 at ffffffff812c89f9
#9 process_one_work+361 at ffffffff810b1889
#10 worker_thread+77 at ffffffff810b233d
#11 kthread+261 at ffffffff810b7fd5
#12 ret_from_fork+62 at ffffffff81a0035e
Thus above forms ABBA deadlock. The same deadlock was mentioned in
upstream commit 28f5a8a7c0 ("ocfs2: should wait dio before inode lock
in ocfs2_setattr()"). It seems that that commit only removed the
cluster lock (the victim of above dead lock) from the ABBA deadlock
party.
End-user visible effects: Process hang in truncate -> ocfs2_setattr path
and other processes hang at ocfs2_dio_end_io_write path.
This is to fix the deadlock itself. It removes inode_lock() call from
dio completion path to remove the deadlock and add ip_alloc_sem lock in
setattr path to synchronize the inode modifications.
[wen.gang.wang@oracle.com: remove the "had_alloc_lock" as suggested]
Link: https://lkml.kernel.org/r/20210402171344.1605-1-wen.gang.wang@oracle.com
Link: https://lkml.kernel.org/r/20210331203654.3911-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3a8833dffb7e7329c2586b8bfc531adb503f123 upstream.
Commit cb9f753a37 ("mm: fix races between swapoff and flush dcache")
updated flush_dcache_page implementations on several architectures to
use page_mapping_file() in order to avoid races between page_mapping()
and swapoff().
This update missed arch/nds32 and there is a possibility of a race
there.
Replace page_mapping() with page_mapping_file() in nds32 implementation
of flush_dcache_page().
Link: https://lkml.kernel.org/r/20210330175126.26500-1-rppt@kernel.org
Fixes: cb9f753a37 ("mm: fix races between swapoff and flush dcache")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Greentime Hu <green.hu@gmail.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad1e366167837daeb93d0bacb57dee820b0b898 upstream.
ia64 has two stacks:
- memory stack (or stack), pointed at by by r12
- register backing store (register stack), pointed at by
ar.bsp/ar.bspstore with complications around dirty
register frame on CPU.
In [1] Dmitry noticed that PTRACE_GET_SYSCALL_INFO returns the register
stack instead memory stack.
The bug comes from the fact that user_stack_pointer() and
current_user_stack_pointer() don't return the same register:
ulong user_stack_pointer(struct pt_regs *regs) { return regs->ar_bspstore; }
#define current_user_stack_pointer() (current_pt_regs()->r12)
The change gets both back in sync.
I think ptrace(PTRACE_GET_SYSCALL_INFO) is the only affected user by
this bug on ia64.
The change fixes 'rt_sigreturn.gen.test' strace test where it was
observed initially.
Link: https://bugs.gentoo.org/769614 [1]
Link: https://lkml.kernel.org/r/20210331084447.2561532-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9562fd132985ea9185388a112e50f2a51557827d upstream.
LLVM changed the expected function signature for llvm_gcda_emit_function()
in the clang-11 release. Users of clang-11 or newer may have noticed
their kernels producing invalid coverage information:
$ llvm-cov gcov -a -c -u -f -b <input>.gcda -- gcno=<input>.gcno
1 <func>: checksum mismatch, \
(<lineno chksum A>, <cfg chksum B>) != (<lineno chksum A>, <cfg chksum C>)
2 Invalid .gcda File!
...
Fix up the function signatures so calling this function interprets its
parameters correctly and computes the correct cfg checksum. In
particular, in clang-11, the additional checksum is no longer optional.
Link: https://reviews.llvm.org/rG25544ce2df0daa4304c07e64b9c8b0f7df60c11d
Link: https://lkml.kernel.org/r/20210408184631.1156669-1-ndesaulniers@google.com
Reported-by: Prasad Sodagudi <psodagud@quicinc.com>
Tested-by: Prasad Sodagudi <psodagud@quicinc.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 4f0ed93fb92d3528c73c80317509df3f800a222b upstream.
That (and traversals in case of umount .) should be done before
complete_walk(). Either a braino or mismerge damage on queue
reorders - either way, I should've spotted that much earlier.
Fucked-up-by: Al Viro <viro@zeniv.linux.org.uk>
X-Paperbag: Brown
Fixes: 161aff1d93 "LOOKUP_MOUNTPOINT: fold path_mountpointat() into path_lookupat()"
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa26d0c778b432d3d9814ea82552e813b33eeb5c upstream.
Commit 8cdddd182bd7 ("ACPI: processor: Fix CPU0 wakeup in
acpi_idle_play_dead()") tried to fix CPU0 hotplug breakage by copying
wakeup_cpu0() + start_cpu0() logic from hlt_play_dead()//mwait_play_dead()
into acpi_idle_play_dead(). The problem is that these functions are not
exported to modules so when CONFIG_ACPI_PROCESSOR=m build fails.
The issue could've been fixed by exporting both wakeup_cpu0()/start_cpu0()
(the later from assembly) but it seems putting the whole pattern into a
new function and exporting it instead is better.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8cdddd182bd7 ("CPI: processor: Fix CPU0 wakeup in acpi_idle_play_dead()")
Cc: <stable@vger.kernel.org> # 5.10+
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6a37a93c9ac3900987c79b726d0bb3699d8db4e upstream.
intel_dsm_platform_mux_info() tries to parse the ACPI package data
from _DSM for the debug information, but it assumes the fixed format
without checking what values are stored in the elements actually.
When an unexpected value is returned from BIOS, it may lead to GPF or
NULL dereference, as reported recently.
Add the checks of the contents in the returned values and skip the
values for invalid cases.
v1->v2: Check the info contents before dereferencing, too
BugLink: http://bugzilla.opensuse.org/show_bug.cgi?id=1184074
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210402082317.871-1-tiwai@suse.de
(cherry picked from commit 337d7a1621c7f02af867229990ac67c97da1b53a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5923249b8fa427943b50b8f35265176472be38 upstream.
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e9005be87777afc902b9f5497495898202d335d upstream.
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6fdeb28f4c331acbd27bdb0effc4befd4ef8e8 upstream.
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 864db232dc7036aa2de19749c3d5be0143b24f8f upstream.
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d120198bd5ff1d41808b6914e1eb89aff937415c upstream.
Unmask operation must be called with interrupt disabled,
on preempt_rt spin_lock_irqsave/spin_unlock_irqrestore
don't disable/enable interrupts, so use raw_* implementation
and change lock variable in struct irq_info from spinlock_t
to raw_spinlock_t
Cc: stable@vger.kernel.org
Fixes: 25da4618af24 ("xen/events: don't unmask an event channel when an eoi is pending")
Signed-off-by: Luca Fancellu <luca.fancellu@arm.com>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20210406105105.10141-1-luca.fancellu@arm.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ad6e9cb39c66366bf7b9aece114aca277981a1f upstream.
Since commit 1b8b31a2e6 ("selinux: convert policy read-write lock to
RCU"), there is a small window during policy load where the new policy
pointer has already been installed, but some threads may still be
holding the old policy pointer in their read-side RCU critical sections.
This means that there may be conflicting attempts to add a new SID entry
to both tables via sidtab_context_to_sid().
See also (and the rest of the thread):
https://lore.kernel.org/selinux/CAFqZXNvfux46_f8gnvVvRYMKoes24nwm2n3sPbMjrB8vKTW00g@mail.gmail.com/
Fix this by installing the new policy pointer under the old sidtab's
spinlock along with marking the old sidtab as "frozen". Then, if an
attempt to add new entry to a "frozen" sidtab is detected, make
sidtab_context_to_sid() return -ESTALE to indicate that a new policy
has been installed and that the caller will have to abort the policy
transaction and try again after re-taking the policy pointer (which is
guaranteed to be a newer policy). This requires adding a retry-on-ESTALE
logic to all callers of sidtab_context_to_sid(), but fortunately these
are easy to determine and aren't that many.
This seems to be the simplest solution for this problem, even if it
looks somewhat ugly. Note that other places in the kernel (e.g.
do_mknodat() in fs/namei.c) use similar stale-retry patterns, so I think
it's reasonable.
Cc: stable@vger.kernel.org
Fixes: 1b8b31a2e6 ("selinux: convert policy read-write lock to RCU")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f5f0ea5b86300390b026b6c6e7836b7150814a upstream.
Currently, duplicate_policydb_cond_list() first copies the whole
conditional avtab and then tries to link to the correct entries in
cond_dup_av_list() using avtab_search(). However, since the conditional
avtab may contain multiple entries with the same key, this approach
often fails to find the right entry, potentially leading to wrong rules
being activated/deactivated when booleans are changed.
To fix this, instead start with an empty conditional avtab and add the
individual entries one-by-one while building the new av_lists. This
approach leads to the correct result, since each entry is present in the
av_lists exactly once.
The issue can be reproduced with Fedora policy as follows:
# sesearch -s ftpd_t -t public_content_rw_t -c dir -p create -A
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t public_content_rw_t:dir { add_name create link remove_name rename reparent rmdir setattr unlink watch watch_reads write }; [ ftpd_anon_write ]:True
# setsebool ftpd_anon_write=off ftpd_connect_all_unreserved=off ftpd_connect_db=off ftpd_full_access=off
On fixed kernels, the sesearch output is the same after the setsebool
command:
# sesearch -s ftpd_t -t public_content_rw_t -c dir -p create -A
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t public_content_rw_t:dir { add_name create link remove_name rename reparent rmdir setattr unlink watch watch_reads write }; [ ftpd_anon_write ]:True
While on the broken kernels, it will be different:
# sesearch -s ftpd_t -t public_content_rw_t -c dir -p create -A
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
While there, also simplify the computation of nslots. This changes the
nslots values for nrules 2 or 3 to just two slots instead of 4, which
makes the sequence more consistent.
Cc: stable@vger.kernel.org
Fixes: c7c556f1e8 ("selinux: refactor changing booleans")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 442dc00f82a9727dc0c48c44f792c168f593c6df upstream.
1. Make sure all fileds are initialized in avtab_init().
2. Slightly refactor avtab_alloc() to use the above fact.
3. Use h->nslot == 0 as a sentinel in the access functions to prevent
dereferencing h->htable when it's not allocated.
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5db93e7f2afbdfe3b78e37879a85290187e6f1 upstream.
When sock_wait_state() returns -EINPROGRESS, "sk->sk_state" is
LLCP_CONNECTING. In this case, llcp_sock_connect() is repeatedly invoked,
nfc_llcp_sock_link() will add sk to local->connecting_sockets twice.
sk->sk_node->next will point to itself, that will make an endless loop
and hang-up the system.
To fix it, check whether sk->sk_state is LLCP_CONNECTING in
llcp_sock_connect() to avoid repeated invoking.
Fixes: b4011239a0 ("NFC: llcp: Fix non blocking sockets connections")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.11
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7574fcdbdcb335763b6b322f6928dc0fd5730451 upstream.
In llcp_sock_connect(), use kmemdup to allocate memory for
"llcp_sock->service_name". The memory is not released in the sock_unlink
label of the subsequent failure branch.
As a result, memory leakage occurs.
fix CVE-2020-25672
Fixes: d646960f79 ("NFC: Initial LLCP support")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.3
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a4cd82d62b5ec7e5482333a72b58a4eea4979f0 upstream.
nfc_llcp_local_get() is invoked in llcp_sock_connect(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().
fix CVE-2020-25671
Fixes: c7aa12252f ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.6
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c33b1cc62ac05c1dbb1cdafe2eb66da01c76ca8d upstream.
nfc_llcp_local_get() is invoked in llcp_sock_bind(),
but nfc_llcp_local_put() is not invoked in subsequent failure branches.
As a result, refcount leakage occurs.
To fix it, add calling nfc_llcp_local_put().
fix CVE-2020-25670
Fixes: c7aa12252f ("NFC: Take a reference on the LLCP local pointer when creating a socket")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.6
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa65bacdb70e549a81de03ec72338e1047842883 upstream.
The SST firmware's media and deep-buffer inputs are hardcoded to
S16LE, the corresponding DAIs don't have a hw_params callback and
their prepare callback also does not take the format into account.
So far the advertising of non working S24LE support has not caused
issues because pulseaudio defaults to S16LE, but changing pulse-audio's
config to use S24LE will result in broken sound.
Pipewire is replacing pulse now and pipewire prefers S24LE over S16LE
when available, causing the problem of the broken S24LE support to
come to the surface now.
Cc: stable@vger.kernel.org
BugLink: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/866
Fixes: 098c2cd281 ("ASoC: Intel: Atom: add 24-bit support for media playback and capture")
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210324132711.216152-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6423ed2da6214a68527446b5f8e09cf7162b2ce upstream.
There is another HP ZBook G5 model with the PCI SSID 103c:844f that
requires the same quirk for controlling the mute LED. Add the
corresponding entry to the quirk table.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212407
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210401171314.667-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8426b2700b57d2760ff335840a02f66a64b6044 upstream.
We've got a report about Acer Aspire E1 (PCI SSID 1025:0840) that
loses the speaker output after resume. With the comparison of COEF
dumps, it was identified that the COEF 0x0d bits 0x6000 corresponds to
the speaker amp.
This patch adds the specific quirk for the device to restore the COEF
bits at the codec (re-)initialization.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1183869
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210407095730.12560-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 168632a495f49f33a18c2d502fc249d7610375e9 upstream.
Add a control to the card before copying the id so that the numid field
is initialized in the copy. Otherwise the numid field of active_id,
format_id, rate_id and channels_id will be the same (0) and
snd_ctl_notify() will not queue the events properly.
Signed-off-by: Jonas Holmberg <jonashg@axis.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210407075428.2666787-1-jonashg@axis.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef19e111337f6c3dca7019a8bad5fbc6fb18d635 upstream.
Replace WARN_ONCE() that can be triggered from userspace with
pr_warn_once(). Those still give user a hint what's the issue.
I've left WARN()s that are not possible to trigger with current
code-base and that would mean that the code has issues:
- relying on current compat_msg_min[type] <= xfrm_msg_min[type]
- expected 4-byte padding size difference between
compat_msg_min[type] and xfrm_msg_min[type]
- compat_policy[type].len <= xfrma_policy[type].len
(for every type)
Reported-by: syzbot+834ffd1afc7212eb8147@syzkaller.appspotmail.com
Fixes: 5f3eea6b7e ("xfrm/compat: Attach xfrm dumps to 64=>32 bit translator")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea29b20a828511de3348334e529a3d046a180416 upstream.
I read the commit log of the following two:
- bc083a64b6 ("init/Kconfig: make COMPILE_TEST depend on !UML")
- 334ef6ed06fa ("init/Kconfig: make COMPILE_TEST depend on !S390")
Both are talking about HAS_IOMEM dependency missing in many drivers.
So, 'depends on HAS_IOMEM' seems the direct, sensible solution to me.
This does not change the behavior of UML. UML still cannot enable
COMPILE_TEST because it does not provide HAS_IOMEM.
The current dependency for S390 is too strong. Under the condition of
CONFIG_PCI=y, S390 provides HAS_IOMEM, hence can enable COMPILE_TEST.
I also removed the meaningless 'default n'.
Link: https://lkml.kernel.org/r/20210224140809.1067582-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KP Singh <kpsingh@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Cc: Quentin Perret <qperret@google.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: "Enrico Weigelt, metux IT consult" <lkml@metux.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 334ef6ed06fa1a54e35296b77b693bcf6d63ee9e upstream.
While allmodconfig and allyesconfig build for s390 there are also
various bots running compile tests with randconfig, where PCI is
disabled. This reveals that a lot of drivers should actually depend on
HAS_IOMEM.
Adding this to each device driver would be a never ending story,
therefore just disable COMPILE_TEST for s390.
The reasoning is more or less the same as described in
commit bc083a64b6 ("init/Kconfig: make COMPILE_TEST depend on !UML").
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26f55a59dc65ff77cd1c4b37991e26497fc68049 upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d4d456436bfb2fe412ee2cd489f7658449b098 upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90a82b1fa40d0cee33d1c9306dc54412442d1e57 ]
This is what I see after compiling the kernel:
# bpf-next...bpf-next/master
?? tools/bpf/resolve_btfids/libbpf/
Fixes: fc6b48f692f8 ("tools/resolve_btfids: Build libbpf and libsubcmd in separate directories")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210212010053.668700-1-sdf@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e1aa629f1ce9e8cb89e0cefb9e3bfb3dfa94821 ]
Nathan reported issue with cleaning empty build directory:
$ make -s O=build distclean
../../scripts/Makefile.include:4: *** \
O=/ho...build/tools/bpf/resolve_btfids does not exist. Stop.
The problem that tools scripts require existing output
directory, otherwise it fails.
Adding check around the resolve_btfids clean target to
ensure the output directory is in place.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/bpf/20210211124004.1144344-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50d3a3f81689586697a38cd60070181ebe626ad9 ]
The resolve_btfids tool is used during the kernel build,
so we should clean it on kernel's make clean.
Invoking the the resolve_btfids clean as part of root
'make clean'.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210205124020.683286-5-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7962cb9b640af98ccb577f46c8b894319e6c5c20 ]
We want this clean to be called from tree's root Makefile,
which defines same srctree variable and that will screw
the make setup.
We actually do not use srctree being passed from outside,
so we can solve this by setting current srctree value
directly.
Also changing the way how srctree is initialized as suggested
by Andrri.
Also root Makefile does not define the implicit RM variable,
so adding RM initialization.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210205124020.683286-4-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f23130979c2f15ea29a431cd9e1ea7916337bbd4 ]
We want this clean to be called from tree's root clean
and that one is silent if there's nothing to clean.
Adding check for all object to clean and display CLEAN
messages only if there are objects to remove.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210205124020.683286-3-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc6b48f692f89cc48bfb7fd1aa65454dfe9b2d77 ]
Setting up separate build directories for libbpf and libpsubcmd,
so it's separated from other objects and we don't get them mixed
in the future.
It also simplifies cleaning, which is now simple rm -rf.
Also there's no need for FEATURE-DUMP.libbpf and bpf_helper_defs.h
files in .gitignore anymore.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210205124020.683286-2-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee4160c73b2102a52bc97a4128a89c34821414f ]
When we cancel a timeout we should emit a sensible return code, like
-ECANCELED but not 0, otherwise it may trick users.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/7b0ad1065e3bd1994722702bd0ba9e7bc9b0683b.1616696997.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 219481a8f90ec3a5eed9638fb35609e4b1aeece7 ]
Make SMB2 not print out an error when an oplock break is received for an
unknown handle, similar to SMB1. The debug message which is printed for
these unknown handles may also be misleading, so fix that too.
The SMB2 lease break path is not affected by this patch.
Without this, a program which writes to a file from one thread, and
opens, reads, and writes the same file from another thread triggers the
below errors several times a minute when run against a Samba server
configured with "smb2 leases = no".
CIFS: VFS: \\192.168.0.1 No task to wake, unknown frame received! NumMids 2
00000000: 424d53fe 00000040 00000000 00000012 .SMB@...........
00000010: 00000001 00000000 ffffffff ffffffff ................
00000020: 00000000 00000000 00000000 00000000 ................
00000030: 00000000 00000000 00000000 00000000 ................
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee8f4f6fcabfdf229542926128e9874d19016d5 ]
RHBZ: 1933527
Under SMB1 + POSIX, if an inode is reused on a server after we have read and
cached a part of a file, when we then open the new file with the
re-cycled inode there is a chance that we may serve the old data out of cache
to the application.
This only happens for SMB1 (deprecated) and when posix are used.
The simplest solution to avoid this race is to force a revalidate
on smb1-posix open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a419cf495f95cac49ea289318b833477e1a0e2 ]
The sleep warning happens at early boot right at secondary CPU
activation bootup:
smp: Bringing up secondary CPUs ...
BUG: sleeping function called from invalid context at mm/page_alloc.c:4942
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.12.0-rc2-00007-g79e228d0b611-dirty #99
..
Call Trace:
show_stack+0x90/0xc0
dump_stack+0x150/0x1c0
___might_sleep+0x1c0/0x2a0
__might_sleep+0xa0/0x160
__alloc_pages_nodemask+0x1a0/0x600
alloc_page_interleave+0x30/0x1c0
alloc_pages_current+0x2c0/0x340
__get_free_pages+0x30/0xa0
ia64_mca_cpu_init+0x2d0/0x3a0
cpu_init+0x8b0/0x1440
start_secondary+0x60/0x700
start_ap+0x750/0x780
Fixed BSP b0 value from CPU 1
As I understand interrupts are not enabled yet and system has a lot of
memory. There is little chance to sleep and switch to GFP_ATOMIC should
be a no-op.
Link: https://lkml.kernel.org/r/20210315085045.204414-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19ec368cbc7ee1915e78c120b7a49c7f14734192 ]
When building out-of-tree, attempting to make target from $(OUTPUT) directory:
make[1]: *** No rule to make target '$(OUTPUT)/protection_keys.c', needed by '$(OUTPUT)/protection_keys_32'.
Link: https://lkml.kernel.org/r/20210315094700.522753-1-rong.a.chen@intel.com
Signed-off-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
