Turing on the headphone amp interferes with the impedance measurement
used to detect a TRRS style headset microphone. Delay the HP turn on
until 500ms after the jack is detected, allowing the mic detection
state machine to run to completion.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for the independent HP reduced the availability of the
side surround output, because there are only 4 DACs for 7.1 and a HP
outputs. Adjust the badness tables for VIA so that 7.1 outputs are
activated for the cost of missing independent HP.
Once when we implement the dynamic DAC switching to multiple outputs,
this conflicts will be eased in future...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The lack of independent HP mode shouldn't be too bad, but currently
its badness is set a bit too high. Let's lower it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The standard badness values don't seem to fit to all preferences.
Some configuration prefer the side output over the headphone, some
want the speaker over the surround, etc.
This patch moves the badness table pointers into hda_gen_spec, so that
the codec driver can override them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge back for-linus branch for the badness table adjustment for VIA codecs
* for-linus:
ALSA: hda - Fix DAC assignment for independent HP
ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
ALSA: hda - Fix typo in checking IEC958 emphasis bit
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
ALSA: snd-usb: mixer: propagate errors up the call chain
ALSA: usb: Parse UAC2 extension unit like for UAC1
ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
The generic parser should evaluate the availability of the independent
HP when specified. Otherwise a DAC without the direct connection to
the corresponding pin may be assigned for the HP, but the driver
doesn't check it at all. The problem was actually seen on some
machines with VT1708s or equivalent codec, where DAC0 is assigned to
HP although it can be connected only via aamix.
This patch adds the badness evaluation for the independent HP to make
it working properly.
Reported-by: Lydia Wang <LydiaWang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we have a "Headset Mic" name, let's use it for some devices
we know for sure has a headset mic jack.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Headset mic jacks, i e TRRS style jacks with Headphone Left,
Headphone Right, Mic and GND signals, are becoming increasingly
common and are now being shipped by several manufacturers.
Unfortunately, the HDA specification does not give us any hint
of whether a Mic pin belongs to such a jack or not, but it would
still be helpful for the user to know (especially if there is one
TRS Mic jack and one TRRS headset jack).
This new fixup causes the first (non-dock, non-internal) mic to
be a headset mic jack. The algorithm can be later refined if needed.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current DSP loader code abuses snd_hda_lock_devices() for ensuring
the DSP loader not conflicting with the other normal operations. But
this trick obviously doesn't work for the PM resume since the streams
are kept opened there where snd_hda_lock_devices() returns -EBUSY.
That means we need another lock mechanism instead of abuse.
This patch provides the new lock state to azx_dev. Theoretically it's
possible that the DSP loader conflicts with the stream that has been
already assigned for another PCM. If it's running, the DSP loader
should simply fail. If not -- it's the case for PM resume --, we
should assign this stream temporarily to the DSP loader, and take it
back to the PCM after finishing DSP loading. If the PCM is operated
during the DSP loading, it should get an error, too.
Reported-and-tested-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a typo in convert_to_spdif_status() about checking the
emphasis IEC958 status bit. It should check the given value instead
of the resultant value.
Reported-by: Martin Weishart <martin.weishart@telosalliance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Creation of individual mixer controls may fail, but that shouldn't cause
the entire mixer creation to fail. Even worse, if the mixer creation
fails, that will error out the entire device probing.
All the functions called by parse_audio_unit() should return -EINVAL if
they find descriptors that are unsupported or believed to be malformed,
so we can safely handle this error code as a non-fatal condition in
snd_usb_mixer_controls().
That fixes a long standing bug which is commonly worked around by
adding quirks which make the driver ignore entire interfaces. Some of
them might now be unnecessary.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Rodolfo Thomazelli <pe.soberbo@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In check_input_term() and parse_audio_feature_unit(), propagate the
error value that has been returned by a failing function instead of
-EINVAL. That helps cleaning up the error pathes in the mixer.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UAC2_EXTENSION_UNIT_V2 differs from UAC1_EXTENSION_UNIT, but can be handled in
the same way when parsing the unit. Otherwise parse_audio_unit() fails when it
sees an extension unit on a UAC2 device.
UAC2_EXTENSION_UNIT_V2 is outside the range allocated by UAC1.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot to update spec->gpio_data in the automute hook, so it will be
overridden at the init sequence, thus the machine is still silent when
no headphone jack is plugged at boot time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new HP desktop machines have Realtek codecs and their LEDs are
controlled via GPIO as for many laptop models. Add similar hooks as
well as in patch_sigmatel.c for controlling LEDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The verb to set up the digital beep via AC_VERB_SET_DIGI_CONVERT_2
should be executed at resume as well. Use the cached write for it
being performed automatically at resume.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While playing the digital beep tone, the codec shouldn't be turned
off. This patch adds proper snd_hda_power_up()/down() calls at each
time when the beep is played or off.
Also, this fixes automatically an unnecessary codec power-up at
detaching the beep device when the beep isn't being played.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling snd_hda_attach_beep_device() and
snd_hda_detach_beep_device() in each codec driver, move them to the
generic parser. The codec driver just needs to set spec->beep_nid for
activating the digital beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The argument passed to snd_hda_attach_beep_device() is a widget NID
while spec->beep_amp holds the composed value for amp controls.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"Playback Design" products need a 50ms delay after setting the USB
interface.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UAC2 compliant audio devices may announce the capability to transport
raw audio data on their endpoints. Catch this and handle it as
'special' stream on the ALSA side.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This field may use up to 32 bits, so it should be handled as unsigned
int.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The maxpacksize field is given in some quirks, but it gets ignored (in
favour of wMaxPacketSize from the first endpoint.) This patch favours
the one in the quirk.
Digidesign Mbox and Mbox 2 are the only affected quirks and the devices
are assumed to be working without this patch. So for safety against the
values in the quirk being incorrect, remove them.
The datainterval is also ignored but there are not currently any quirks
which choose to override this.
Cc: Damien Zammit <damien@zamaudio.com>
Cc: Chris J Arges <christopherarges@gmail.com>
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware also has a PCM capture device which is not implemented in
this patch.
It may be possible to generalise this to Saffire 6 USB support and some
of the other Focusrite interfaces, but as I don't have access to these
devices we should wait until capture support is working first.
Capture support is not implemented because the code assumes the endpoint
to have its own interface (instead, it shares the interface with playback)
and some thought will be needed to lift this limitation.
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the transition to the generic parser, the hook to the codec
specific automute function was forgotten. This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.
If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it. Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec. The dspload_is_loaded() function returns
true if the DSP transfer was never started. This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called. dsp_loaded should never be set to true in this case,
skip it. The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there are no internal speakers, we should not turn the eapd switch
off, because it might be necessary to keep high for Headphone.
BugLink: https://bugs.launchpad.net/bugs/1155016
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the driver doesn't power down the widget at going down to D3
when the widget node has an EAPD capability and EAPD is actually set
on all codecs unless codec->power_filter is set explicitly.
This caused a problem on some Conexant codecs, leading to click
noises, and we set it as NULL there. But it is very unlikely that the
problem hits only these codecs.
Looking back at the development history, this workaround for EAPD was
introduced just for some laptops with STAC9200 codec, then we applied
it blindly for all. Now, since it's revealed to have an ill effect,
we should disable this workaround per default and apply only for the
known requiring systems.
The EAPD workaround is implemented now as snd_hda_codec_eapd_power_filter(),
and this has to be set explicitly by the codec driver when needed.
As of now, only patch_stac9200() sets this one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the dynamic array allocations for pins, converters and PCM arrays
instead of the fixed size arrays. The modern HDMI codecs get more and
more pins, and we don't know the sensitive limit.
Most of the patch are spent for the straight conversions from the
fixed array access to snd_array helpers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the connection list expansion in hda_codec.c and hda_proc.c, the
value returned from snd_hda_get_num_raw_conns() is used as the array
size to store the connection list. However, the function returns
simply a raw value of the AC_PAR_CONNLIST_LEN parameter, and the
widget list with ranges isn't considered there. Thus it may return a
smaller size than the actual list, which results in -ENOSPC in
snd_hda_get_raw_conections().
This patch fixes the bug by parsing the connection list correctly also
for snd_hda_get_num_raw_conns().
Reported-and-tested-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The NuForce UDH-100 numbers its interfaces incorrectly, which makes the
interface associations come out wrong, which results in the driver
erroring out with the message "Audio class v2 interfaces need an
interface association".
Work around this by searching for the interface association descriptor
also in some other place where it might have ended up.
Reported-and-tested-by: Dave Helstroom <helstroom@google.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dereference should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
script/kernel-doc reports the following type of warnings (when run in verbose
mode):
Warning(sound/core/init.c:152): No description found for return value of
'snd_card_create'
To fix that:
- add missing descriptions of function return values
- use "Return:" sections to describe those return values
Along the way:
- complete some descriptions
- fix some typos
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Expose the newly added TCO LTC and sync check functions to userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds new ALSA controls to query the LTC state from userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch prepares snd_hdspm_get_sync_check() to also check the TCO
sync state. The added feature will be exposed to the user in a later
commit.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Considerably shorten the code by using a macro. Though this won't lower
the binary size, it makes the source more readable.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For 96kHz, MADI allows to multiplex the samples (SMUX) or to use a
dedicated 96K mode. The RME cards default to 96K mode, but since not all
external MADI equipment supports this, provide a switch to users that
changes the on-wire protocol to SMUX.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When using the additional Time Code Option module in slave mode or the
SYNC-In wordclock connector, the sample rate needs to be returned by
hdspm_external_sample_rate().
Since this sample rate may contain any value with 1Hz granularity, we
need to round it to a common rate as done by the OSX driver.
[Fixed missing function declarations by tiwai]
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
