Commit Graph

340 Commits

Author SHA1 Message Date
Lendacky, Thomas
e2a2729a92 amd-xgbe: Use proper Rx flow control register
Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register.  The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-23 22:17:06 -08:00
Ben Hutchings
5bdc73800d mii: Handle link state changes for forced modes in mii_check_media()
mii_check_media() does not update the link (carrier) state or log link
changes when the link mode is forced.  Drivers using the mii library
must do this themselves, but most of them do not.

Instead of changing them all, provide a sensible default behaviour
similar to mii_check_link() when the mode is forced.

via-rhine depends on it being a no-op in this case, so make its call
to mii_check_media() conditional.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-19 15:43:42 -05:00
Lendacky, Thomas
82a19035d0 amd-xgbe: Add ACPI support
Add support for ACPI to the amd-xgbe and amd-xgbe-phy drivers. This
support converts many of the device tree APIs to the new device_property
APIs.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:20 -05:00
Lendacky, Thomas
c3152d4728 amd-xgbe-phy: Change auto-negotiation logic
The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:20 -05:00
Lendacky, Thomas
a83ef427b7 amd-xgbe: Remove need for Tx path spinlock
Since the Tx ring cleanup can run at the same time that data is being
transmitted, a spin lock was used to protect the ring. This patch
eliminates the need for Tx spinlocks by updating the current ring
position only after all ownership bits for data being transmitted have
been set. This will insure that ring operations in the Tx cleanup path
do not interfere with the ring operations in the Tx transmit path.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:20 -05:00
Lendacky, Thomas
270894e7dc amd-xgbe: Simplify the Rx desciptor ring tracking
Make the Rx descriptor ring processing similar to the Tx descriptor
ring processing.  Remove the realloc_index and realloc_threshold
variables and base everything on the current index counter and the
dirty index counter.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:20 -05:00
Lendacky, Thomas
916102c666 amd-xgbe: Clear all state during a device restart
When performing a device restart, like during an MTU change, sometimes
the device queues still have data and get hung up trying to flush
resulting in the device becoming unresponsive until brought down and
back up. To prevent this, always perform a device reset during a
restart.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:20 -05:00
Lendacky, Thomas
94c043e533 amd-xgbe: Add check to be sure amd-xgbe-phy driver is used
The amd-xgbe driver relies on the amd-xgbe-phy phylib driver. Add a
check to be sure that if any errors occur during probing of the
amd-xgbe-phy driver then the amd-xgbe driver returns an error.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:19 -05:00
Lendacky, Thomas
1d67d7f6e9 amd-xgbe: Checkpatch fixes
This set of patches resolves some checks reported by the checkpatch
tool.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-16 22:24:19 -05:00
Geert Uytterhoeven
8f2bfe5f35 net: atarilance: Remove obsolete IRQ_TYPE_PRIO
IRQ_TYPE_PRIO is no longer used by the Atari platform interrupt code
since commit 734085651c ("[PATCH] m68k: convert atari irq code")
in v2.6.18-rc1, so drop it.

Note that its value has been reused for a different purpose
(IRQ_TYPE_EDGE_FALLING) since commit 6a6de9ef58 ("[PATCH] genirq:
core") in v2.6.18-rc1.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
2015-01-15 13:44:50 +01:00
Jiri Pirko
df8a39defa net: rename vlan_tx_* helpers since "tx" is misleading there
The same macros are used for rx as well. So rename it.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-13 17:51:08 -05:00
Richard Cochran
8b976e9777 net: xgbe: convert to timecounter adjtime.
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.

Compile tested only.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30 18:29:26 -05:00
Richard Cochran
74d23cc704 time: move the timecounter/cyclecounter code into its own file.
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30 18:29:25 -05:00
Linus Torvalds
e6b5be2be4 Driver core patches for 3.19-rc1
Here's the set of driver core patches for 3.19-rc1.
 
 They are dominated by the removal of the .owner field in platform
 drivers.  They touch a lot of files, but they are "simple" changes, just
 removing a line in a structure.
 
 Other than that, a few minor driver core and debugfs changes.  There are
 some ath9k patches coming in through this tree that have been acked by
 the wireless maintainers as they relied on the debugfs changes.
 
 Everything has been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
 53kAoLeteByQ3iVwWurwwseRPiWa8+MI
 =OVRS
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...
2014-12-14 16:10:09 -08:00
David S. Miller
22f10923dd Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/amd/xgbe/xgbe-desc.c
	drivers/net/ethernet/renesas/sh_eth.c

Overlapping changes in both conflict cases.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-10 15:48:20 -05:00
Lendacky, Thomas
f9c5c62db1 amd-xgbe: Use disable_irq_nosync when in IRQ context
The disable_irq_nosync function, not the disable_irq function, must be
used to disable the DMA channel interrupt from within the interrupt
service routine. Change the disable_irq call to disable_irq_nosync.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-09 21:48:01 -05:00
Lendacky, Thomas
244d62be91 amd-xgbe: Prevent Tx cleanup stall
When performing Tx cleanup, the dirty index counter is compared to the
current index counter as one of the tests used to determine when to stop
cleanup. The "less than" test will fail when the current index counter
rolls over to zero causing cleanup to never occur again. Update the test
to a "not equal" to avoid this situation.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-09 14:47:46 -05:00
Lendacky, Thomas
c153031773 amd-xgbe: Associate Tx SKB with proper ring descriptor
The SKB for a Tx packet is associated with an xgbe_ring_data structure
in the xgbe_map_tx_skb function.  However, it is being saved in the
structure after the last structure used when the SKB is mapped.  Use
the last used structure to save the SKB value.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-09 13:15:42 -05:00
Lendacky, Thomas
03ccc4c0a9 amd-xgbe: Do not clear interrupt indicator
The interrupt value within the xgbe_ring_data structure is used as an
indicator of which Rx descriptor should have the INTE bit set to
generate an interrupt when that Rx descriptor is used.  This bit was
mistakenly cleared in the xgbe_unmap_rdata function, effectively
nullifying the ethtool rx-frames support.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-09 13:15:42 -05:00
Lendacky, Thomas
54ceb9ec6f amd-xgbe: IRQ names require allocated memory
When requesting an irq, the name passed in must be (part of) allocated
memory. The irq name was a local variable and resulted in random
characters when listing /proc/interrupts. Add a character field to the
xgbe_channel structure to hold the irq name and use that.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-09 13:13:39 -05:00
Eyal Perry
892311f66f ethtool: Support for configurable RSS hash function
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.

It modifies drivers implementation of set/get_rxfh accordingly.

This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.

User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.

Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.

Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-08 21:07:10 -05:00
Lendacky, Thomas
16958a2b05 amd-xgbe: Add support for the skb->xmit_more flag
Add support to delay telling the hardware about data that is ready to
be transmitted if the skb->xmit_more flag is set.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:11 -05:00
Lendacky, Thomas
eb79e640fa amd-xgbe: Perform Tx coalescing on a packet basis
The current form of Tx coalescing works on a descriptor basis instead
of on a packet basis and doesn't take into account TSO packets. Update
the Tx coalescing support to work on a packet basis, taking into
account the number of packets associated with a TSO transmit. Also,
only activate the Tx timer if a timer value is set.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:11 -05:00
Lendacky, Thomas
16978eb7bc amd-xgbe: Remove unused variable
The tso_header variable in the xgbe_tx_ring_data structure is not used,
remove it.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:11 -05:00
Lendacky, Thomas
5fb4b86a66 amd-xgbe: Add BQL support
Call the appropriate BQL functions to track the number of bytes queued
during Tx processing and to track the number of packets and bytes
that have been transmitted during Tx complete processing.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:11 -05:00
Lendacky, Thomas
c9f140ebb0 amd-xgbe: Separate Tx/Rx ring data fields into new structs
Move the Tx and Rx related fields within the xgbe_ring_data struct into
their own structs in order to more easily see what fields are used for
each operation.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:11 -05:00
Lendacky, Thomas
7bba35bdda amd-xgbe: Incorporate Smatch coding suggestion
The Smatch tool indicated that one of the if statements in xgbe-dev.c
could be rewritten to remove a redundant check for the 'err' variable
in an if statement.

Change the statement as suggested and add a comment to help clarify.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:10 -05:00
Lendacky, Thomas
16edd34e9e amd-xgbe: Tx engine must not be active before stopping it
If the Tx engine is told to stop while it is actively processing Tx
descriptors it is possible that the Tx descriptor(s) will not be closed
out properly. When the Tx engine is restarted this could result in the
driver being stuck on the improperly closed descriptor.

Update the driver to wait for the Tx engine to be in a stopped or
suspended state before issuing the stop command.

This has not been an issue to date, but it's a good safe-guard to have.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:10 -05:00
Lendacky, Thomas
5449e27167 amd-xgbe: Add a read memory barrier to Tx/Rx path
Add a read memory barrier to the Tx and Rx paths where the ownership
bit is checked to be sure that all descriptor fields are read after
having read the ownership bit for the descriptor.

This has not been an issue to date, but it's a good safe-guard to have.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21 15:19:10 -05:00
Eric Dumazet
b23063034f amd-xgbe: use netdev_rss_key_fill() helper
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lendacky, Thomas <Thomas.Lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-16 15:59:11 -05:00
Dan Carpenter
b6267d3e80 amd-xgbe: fix ->rss_hash_type
There was a missing break statement so we set everything to
PKT_HASH_TYPE_L3 even when we intended to use PKT_HASH_TYPE_L4.

Fixes: 5b9dfe299e ('amd-xgbe: Provide support for receive side scaling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-13 14:39:54 -05:00
Lendacky, Thomas
5226cfc500 amd-xgbe: Fix sparse endian warnings
Change the types of the descriptor entries in the xgbe_ring_desc struct
from u32 to __le32 to fix endian warnings issued by sparse.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-12 15:10:23 -05:00
Lendacky, Thomas
f5eecbbef0 amd-xgbe: Check for complete packet on skb allocation error
If the skb allocation fails during receive processing, the driver would
continue reading descriptors without first determining if there were
any more descriptors for the current packet. Update the code to check
whether more descriptors are associated with the current packet or
whether to move on to the next descriptor as a new packet.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-06 19:00:15 -05:00
Lendacky, Thomas
e98c72c942 amd-xgbe: Free channel/ring structures later
The channel structure is freed before freeing the per channel
interrupts resulting in a kernel oops. Move the call to free
the channel structure to after the freeing of the per channel
interrupts.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-06 19:00:15 -05:00
Lendacky, Thomas
474809b9e1 amd-xgbe: Let AMD_XGBE depend on HAS_IOMEM
The amd-xgbe driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:13 -05:00
Lendacky, Thomas
a7beaf2300 amd-xgbe: Fix a spelling error
This patch fixes the spelling of the word "descriptor" in a couple
of locations.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
f6ac862845 amd-xgbe: Add receive side scaling ethtool support
This patch adds support for ethtool receive side scaling (RSS) commands.
Support is added to get/set the RSS hash key and the RSS lookup table.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
5b9dfe299e amd-xgbe: Provide support for receive side scaling
This patch provides support for receive side scaling (RSS). RSS allows
for spreading incoming network packets across the Rx queues.  When used
in conjunction with the per DMA channel interrupt support, this allows
the receive processing to be spread across multiple processors.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
9227dc5e57 amd-xgbe: Add support for per DMA channel interrupts
This patch provides support for interrupts that are generated by the
Tx/Rx DMA channel pairs of the device.  This allows for Tx and Rx
processing to run across multiple processsors.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
174fd2597b amd-xgbe: Implement split header receive support
Provide support for splitting IP packets so that the header and
payload can be sent to different DMA addresses.  This will allow
the IP header to be put into the linear part of the skb while the
payload can be added as frags.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
08dcc47c06 amd-xgbe: Use page allocations for Rx buffers
Use page allocations for Rx buffers instead of pre-allocating skbs
of a set size.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
aa96bd3c9f amd-xgbe: Use the u32 data type for descriptors
The Tx and Rx descriptors are unsigned 32 bit values.  Use the u32
type, rather than unsigned int, to map these descriptors.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
a9d41981e9 amd-xgbe: Rename pre_xmit function to dev_xmit
The pre_xmit function name implies that it performs operations prior
to transmitting the packet when in fact it is responsible for setting
up the descriptors and initiating the transmit.  Rename this to
function from pre_xmit to dev_xmit, which is consistent with the name
used during receive processing - dev_read.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:12 -05:00
Lendacky, Thomas
4780b7cae6 amd-xgbe: Move ring allocation to device open
Move the channel and ring tracking structures allocation to device
open.  This will allow for future support to vary the number of Tx/Rx
queues without unloading the module.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-05 21:50:11 -05:00
Greg Kroah-Hartman
a8a93c6f99 Merge branch 'platform/remove_owner' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
2014-11-03 19:53:56 -08:00
Lendacky, Thomas
55ca6bcd73 amd-xgbe: Fix napi Rx budget accounting
Currently the amd-xgbe driver increments the packets processed counter
each time a descriptor is processed.  Since a packet can be represented
by more than one descriptor incrementing the counter in this way is not
appropriate.  Also, since multiple descriptors cause the budget check
to be short circuited, sometimes the returned value from the poll
function would be larger than the budget value resulting in a WARN_ONCE
being triggered.

Update the polling logic to properly account for the number of packets
processed and exit when the budget value is reached.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22 17:50:31 -04:00
Lendacky, Thomas
386f1c9650 amd-xgbe: Properly handle feature changes via ethtool
The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support.  Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22 17:50:31 -04:00
Wolfram Sang
884df0a314 net: ethernet: amd: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:21:04 +02:00
Jeff Kirsher
5f5316fcd0 am2150: Update nmclan_cs.c to use update PCMCIA API
Resolves compile warning about use of a deprecated function call:
drivers/net/ethernet/amd/nmclan_cs.c: In function ‘nmclan_config’:
drivers/net/ethernet/amd/nmclan_cs.c:624:3: warning: ‘pcmcia_request_exclusive_irq’ is deprecated (declared at include/pcmcia/ds.h:213) [-Wdeprecated-declarations]
   ret = pcmcia_request_exclusive_irq(link, mace_interrupt);

Updates pcmcia_request_exclusive_irq() to pcmcia_request_irq().

CC: Roger Pao <rpao@paonet.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-22 14:27:44 -04:00
Varka Bhadram
e9c3f99f8b ethernet: amd: use pr_info_once()
It will use pr_info_one() to print the version info of the
driver in probe function only once. No need to use the static
variable here.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12 18:02:41 -04:00
David S. Miller
eb84d6b604 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2014-09-07 21:41:53 -07:00
Lendacky, Thomas
a3ba7c989d amd-xgbe: Enable interrupts for all management counters
As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.

Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-05 22:37:30 -07:00
Lendacky, Thomas
6026510896 amd-xgbe: Treat certain counter registers as 64 bit
Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers.  Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).

Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-05 22:37:30 -07:00
Lendacky, Thomas
a2ea14d772 amd-xgbe: Checkpatch driver fixes
This patch contains fixes identified by checkpatch when run with the
strict option.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-05 15:11:20 -07:00
Lendacky, Thomas
bec6bfb243 amd-xgbe: Fix initialization of the wrong spin lock
During allocation and initialization of the network driver structures,
the wrong pointer is used to initialize a spin lock. Fix the spin lock
initialization by using the proper pointer.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-02 14:03:37 -07:00
Lendacky, Thomas
9fc69affda amd-xgbe: Use the Tx queue count for Tx flow control support
When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Lendacky, Thomas
625c8e4a2f amd-xgbe: Fix the xpcs mmd debugfs support
The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used.  Update the debugfs support to generate the
proper mmd register value.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Lendacky, Thomas
f076f45372 amd-xgbe: Reported fifo size from hardware is not correct
The fifo size reported by the hardware is not correct. Add support
to limit the reported size to what is actually present.  Also, fix
the argument types used in the fifo size calculation function.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Lendacky, Thomas
a9a4a2d9d6 amd-xgbe: Check for Tx hardware queue flushing support
The flushing of the Tx hardware queues is only supported at a certain
level of the hardware.  Retrieve the current version of the hardware
and use that to determine if flushing is supported.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 20:38:14 -07:00
Linus Torvalds
a11c5c9ef6 PCI changes for the v3.17 merge window (part 2):
Miscellaneous
     - Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT7PyAAAoJEFmIoMA60/r8kjQQALr/8oEfZoVcjgCb7waWOr25
 hUTnrI6GBIAh/50hoBiPq0ouPCAKVv66+CUhuhFkLP7oJz+rMU0B9hfUvdLfmCpH
 7ppaallkllT9nPFIr7h5RUWLXsoQyuHmCYmSrUCcnlT2LPgU0dN72YWElLisEM6Z
 Pldg3933xyIQaCWviHjGEjWb7NvC+JY4pTkV5iyqGgU8Ale/eFYtLLSfdBEjIbGv
 VDirYZmKELYeuncZPrTAsp4IENRMZn702wwDakMSODVMEWtJB5h4yrBawqQDlFP5
 9ztIX6n9p9zkdVKbYZlx/Xwv6SYEnYXLxauVQMSO3Nck7Z10R5Ud+5uuCg/6mWH8
 AQI4UV5bbJcg7zHgocTG9XLFLFPoPtD2JT6k6UT1LeUAiAOqcSzhRO+/qJBmJOWZ
 Zv+EHXPlxBrl0zNifut6ZQrY17teuItVtmha70a/9W3PjnIx3KecqLcTwdTvDsOY
 IAyH8WMZrBKpPpsczSmfE93i2Z1QRS91HEAOeSMxl/98dcDTdllYZS7spjoDll2f
 xmpGDbpriLSCu2XsGHfTC9RbqA7CyuFlHggJSQDkT/5Esli0sCs7eweTuK3RVvPu
 t6bUHK3yElb6x9qMZhb5q6l72wSMlGMishTdaxEHmqrEA8PtaIFodmVX2T/Zel5n
 GHN6bysPqDItNR2v/3JX
 =jJGu
 -----END PGP SIGNATURE-----

Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
 "Part two of the PCI changes for v3.17:

    - Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)

  It's a mechanical change that removes uses of the
  DEFINE_PCI_DEVICE_TABLE macro.  I waited until later in the merge
  window to reduce conflicts, but it's possible you'll still see a few"

* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
2014-08-14 18:10:33 -06:00
Linus Torvalds
f0094b28f3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:
 "Several networking final fixes and tidies for the merge window:

   1) Changes during the merge window unintentionally took away the
      ability to build bluetooth modular, fix from Geert Uytterhoeven.

   2) Several phy_node reference count bug fixes from Uwe Kleine-König.

   3) Fix ucc_geth build failures, also from Uwe Kleine-König.

   4) Fix klog false positivies when netlink messages go to network
      taps, by properly resetting the network header.  Fix from Daniel
      Borkmann.

   5) Sizing estimate of VF netlink messages is too small, from Jiri
      Benc.

   6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.

   7) VLAN untagging is erroneously dependent upon whether the VLAN
      module is loaded or not, but there are generic dependencies that
      matter wrt what can be expected as the SKB enters the stack.
      Make the basic untagging generic code, and do it unconditionally.
      From Vlad Yasevich.

   8) xen-netfront only has so many slots in it's transmit queue so
      linearize packets that have too many frags.  From Zoltan Kiss.

   9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
      Fainelli"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
  net: bcmgenet: correctly resume adapter from Wake-on-LAN
  net: bcmgenet: update UMAC_CMD only when link is detected
  net: bcmgenet: correctly suspend and resume PHY device
  net: bcmgenet: request and enable main clock earlier
  net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
  xen-netfront: Fix handling packets on compound pages with skb_linearize
  net: fec: Support phys probed from devicetree and fixed-link
  smsc: replace WARN_ON() with WARN_ON_SMP()
  xen-netback: Don't deschedule NAPI when carrier off
  net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
  wan: wanxl: Remove typedefs from struct names
  m68k/atari: EtherNEC - ethernet support (ne)
  net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
  hdlc: Remove typedefs from struct names
  airo_cs: Remove typedef local_info_t
  atmel: Remove typedef atmel_priv_ioctl
  com20020_cs: Remove typedef com20020_dev_t
  ethernet: amd: Remove typedef local_info_t
  net: Always untag vlan-tagged traffic on input.
  drivers: net: Add APM X-Gene SoC ethernet driver support.
  ...
2014-08-13 18:27:40 -06:00
Benoit Taine
9baa3c34ac PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-08-12 12:15:14 -06:00
Joe Perches
e03aec1686 drivers/net/ethernet/amd/pcnet32.c: neaten and remove unnecessary OOM messages
Make the code flow a little better for 80 columns.

Use a consistent style for the RX and TX rings allocation.
Use BIT macro.
Use a temporary unsiged int entries for (1<<size).
Remove the OOM messages as they duplicate the generic
OOM and dump_stack() provided by the memory subsystem.
Reflow allocs to 80 columns.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Don Fry <pcnet32@frontier.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-08 15:57:30 -07:00
Joe Perches
8c6a5dca88 amd: use pci_zalloc_consistent
Remove the now unnecessary memset too.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Don Fry <pcnet32@frontier.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-08 15:57:29 -07:00
Jean Sacren
67f2527a68 amd: xgbe: fix duplicate #include of linux/phy.h
The header linux/phy.h was included twice, so delete one of them.

Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-07 16:02:57 -07:00
Linus Torvalds
e669830526 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for 3.17.  It contains:

   - misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy  updates
   - MIPS ptrace updates and cleanups
   - various fixes that will also go to -stable
   - a number of cleanups and small non-critical fixes.
   - NUMA support for the Loongson 3.
   - more support for MSA
   - support for MAAR
   - various FP enhancements and fixes"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
  MIPS: jz4740: remove unnecessary null test before debugfs_remove
  MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
  MIPS: ZBOOT: implement stack protector in compressed boot phase
  MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
  MIPS: Bonito64: remove a duplicate define
  MIPS: Malta: initialise MAARs
  MIPS: Initialise MAARs
  MIPS: detect presence of MAARs
  MIPS: define MAAR register accessors & bits
  MIPS: mark MSA experimental
  MIPS: Don't build MSA support unless it can be used
  MIPS: consistently clear MSA flags when starting & copying threads
  MIPS: 16 byte align MSA vector context
  MIPS: disable preemption whilst initialising MSA
  MIPS: ensure MSA gets disabled during boot
  MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
  MIPS: fix MSA context for tasks which don't use FP first
  MIPS: init upper 64b of vector registers when MSA is first used
  MIPS: save/disable MSA in lose_fpu
  MIPS: preserve scalar FP CSR when switching vector context
  ...
2014-08-07 08:47:00 -07:00
Lendacky, Thomas
88131a812b amd-xgbe: Perform phy connect/disconnect at dev open/stop
A change added to the mdiobus/phy api added a module_get/module_put
during phy connect/disconnect processing. Currently, the driver
performs a phy connect during module probe and a phy disconnect during
module remove. With the addition of the module_get during phy connect
the amd-xgbe module use count is incremented and can no longer be
unloaded.

Move the phy connect/disconnect from the driver probe/remove functions
to the net_device_ops ndo_open/ndo_stop functions.  This allows the
module use count to be decremented when the device(s) are brought down
and allows the module to be unloaded.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-05 16:47:02 -07:00
Lendacky, Thomas
f3d0e78d2e amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
Use the dma_set_mask_and_coherent function to set the DMA mask rather
than setting the DMA mask fields directly.  This was originally done
to work around a bug in the arm64 DMA support when RAM started above
the 4GB boundary which has since been fixed.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-05 16:47:02 -07:00
Lendacky, Thomas
8c43a2cc75 amd-xgbe: Remove unnecessary spinlocks
Remove the spinlocks around the ethtool get and set settings
functions and within the link adjustment callback routine.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-02 19:29:53 -07:00
Lendacky, Thomas
fca2d99428 amd-xgbe: Add traffic class support
This patch adds support for traffic classes as well as support
for Data Center Bridging interfaces related to traffic classes
and priority flow control.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 18:46:53 -07:00
Lendacky, Thomas
853eb16b8b amd-xgbe: Base queue fifo size and enablement on ring count
When setting the fifo sizes for the queues and enabling the queues
use the number of active Tx and Rx queues that have been enabled
not the maximum number available.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 18:46:52 -07:00
Lendacky, Thomas
f047604a3f amd-xgbe: Update/fix 2.5GbE support
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 18:46:52 -07:00
Lendacky, Thomas
23e4eef7cf amd-xgbe: Add hardware timestamp support
This patch adds support for Tx and Rx hardware timestamping.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 18:46:52 -07:00
David S. Miller
f139c74a8d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-30 13:25:49 -07:00
Manuel Lauss
2f73bfbe08 MIPS: Alchemy: remove au_read/write/sync
replace au_read/write/sync with __raw_read/write and wmb.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7465/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-07-30 13:56:34 +02:00
Manuel Lauss
fb1a7602dd MIPS: Alchemy: move ethernet registers to ethernet driver
Move the register offsets and bit descriptions from the au1000.h header
to their only user, the au1000_eth.c driver.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-07-30 13:50:19 +02:00
Wei Yongjun
332cfc823d amd-xgbe: Fix error return code in xgbe_probe()
Fix to return a negative error code from the setting real tx queue
count error handling case instead of 0.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-23 14:54:12 -07:00
Lendacky, Thomas
6964e97051 amd-xgbe: Remove the adjustments needed for fixed speed
With the addition of entries in the phy speed/duplex settings
array to support KR and KX mode, the work-around to add/remove
baseT settings to run at a fixed speed is no longer needed.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-15 16:30:04 -07:00
Varka Bhadram
46c73ecc61 ethernet: amd: fix 'foo* bar'
This patch fix the 'foo*' bar with 'foo *bar' and (foo*) with (foo *).

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram
ba69a3d78e ethernet: amd: fix pci device ids
Normally any device ids will be above the corresponding device driver
structure. This patch moves the pci device ids and MODULE_DEVICE_TABLE()
above the pci driver structure.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram
13a4fa43bf ethernet: amd: fix comment styles
This patch fixes the comment style issues

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram
f7afbaa557 ethernet: amd: dynamic debug fixes
This patch convert printk() to netdev_dbg/info/err or dev_info/err/dbg

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram
711fec5d22 ethernet: amd: use devm_ioremap()
This patch replace ioremap() with the devm_ioremap() so that
the resource will be freed automatically with the probe failed.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Varka Bhadram
43519e60ef ethernet: amd: move amd111e_remove_one after probe
This patch moves the remove functionalities after the probe
so that we can see the registered and released resources properly.
Every driver follows the same concept.

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-14 19:14:15 -07:00
Maciej W. Rozycki
3d5baba0ec declance: Fix 64-bit compilation warnings
This fixes compiler warnings:

drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size

in 64-bit compilation.  Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p.  Also the
remaining `0x' prefix is dropped for consistency across these messages.

Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-08 14:04:30 -07:00
Lendacky, Thomas
cfa50c7811 amd-xgbe: Base AXI DMA cache settings on device tree
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required.  If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.

Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node.  If present, use settings that work with the caches.  If not
present, use settings that do not look at the caches.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07 21:38:06 -07:00
Lendacky, Thomas
9867e8fb2c amd-xgbe: Performance enhancements
This patch provides some general performance enhancements for the
driver:
  - Modify the default coalescing settings (reduce usec, increase frames)
  - Change the AXI burst length to 256 bytes (default was 16 bytes which
    was smaller than a cache line)
  - Change the AXI cache settings to write-back/write-allocate which
    allocate cache entries for received packets during the DMA since the
    packet will be processed soon afterwards
  - Combine ioread/iowrite when disabling both the Tx and Rx interrupts
  - Change to processing the Tx/Rx channels in pairs
  - Only recycle the Rx descriptors when a threshold of dirty descriptors
    is reached

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07 21:38:06 -07:00
Lendacky, Thomas
ff42606eed amd-xgbe: Call netif_napi_del on ndo_stop operation
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called.  However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload.  Add a call to netif_napi_del during
the ndo_stop operation.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07 21:38:06 -07:00
Lendacky, Thomas
91f873453b amd-xgbe: Clear the proper MTL interrupt register
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07 21:38:06 -07:00
Lendacky, Thomas
f3f128d40c amd-xgbe: Fix debugfs compatibility change with kstrtouint
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal.  Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.

Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07 21:38:06 -07:00
Lendacky, Thomas
66f95c35c4 amd-xgbe: Resolve checkpatch warning about sscanf usage
Checkpatch issued a warning preferring to use kstrto<type> when
using a single variable sscanf.  Change the sscanf invocation to
a kstrtouint call.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26 17:14:04 -07:00
Lendacky, Thomas
b85e4d8960 amd-xgbe: Change destination address filtering support
Currently the driver makes use of the additional mac address
registers in the hardware to provide perfect filtering.  The
hardware can also have a set of hash table registers that can
be used for imperfect filtering.  By using imperfect filtering
the additional mac address registers can be used for layer 2
filtering support.  Use the hash table registers if the device
has them.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26 17:14:04 -07:00
Lendacky, Thomas
801c62d945 amd-xgbe: Add support for VLAN filtering
This patch adds support for (imperfect) filtering of
VLAN tag ids using a 16-bit filter hash table.  When
VLANs are added, a 4-bit hash is calculated with the
result indicating the bit in the hash table to set.
This table is used by the hardware to drop packets with
a VLAN id that does not hash to a set bit in the table.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26 17:14:04 -07:00
Lendacky, Thomas
c52e9c6385 amd-xgbe: VLAN Rx tag stripping fix
When receiving a VLAN packet check to be sure that VLAN
RX CTAG stripping is enabled before indicating that the
tag has been stripped in the packet information data
structure.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26 17:14:04 -07:00
Lendacky, Thomas
6e5eed042f amd-xgbe: VLAN Tx tag insertion fix
The MAC_VLAN_Incl register (0x0060) must be set to indicate
that the VLAN tag to be inserted comes from a Tx context
descriptor and not the MAC_VLAN_Incl register.  Also, even
though it is the default, explicitly set the type of tag to
be inserted as a CTAG.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26 17:14:03 -07:00
Lendacky, Thomas
d0a8ba6cba amd-xgbe: Make defines in xgbe.h unique
In order to avoid conflicts with other include files, add
a prefix to the defines in xgbe.h.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26 17:14:03 -07:00
Dan Carpenter
8fc908c3c3 amd-xgbe: unwind on error in xgbe_mdio_register()
There is a typo here so we return directly instead of unwinding.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-11 15:39:19 -07:00
Lendacky, Thomas
d5c4858237 amd-xgbe: Rename MAX_DMA_CHANNELS to avoid powerpc conflict
MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc
architecture.  Rename this #define in xgbe.h to avoid the
redefined warning issued during compilation.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-11 00:56:41 -07:00
Tom Lendacky
1caaab63d3 amd-xgbe: Remove unnecessary include
The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-06 13:09:50 -07:00
David S. Miller
f666f87b94 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/xen-netback/netback.c
	net/core/filter.c

A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.

A xen-netback bug fix overlapped the addition of multi-queue
support.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 16:22:02 -07:00
Lendacky, Thomas
1ebe98dcd8 amd-xgbe: Configuration and build support
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:26:51 -07:00
Lendacky, Thomas
c5aa9e3b81 amd-xgbe: Initial AMD 10GbE platform driver
This patch provides the initial platform driver for the AMD
10GbE device.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:26:51 -07:00
Amos Kong
78c8dbb652 hplance: fix ram size in comment
drivers/net/ethernet/amd/hplance.h:
 #define HPLANCE_MEMOFF 0x8000   /* struct lance_init_block */
 #define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */

The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.

Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:14:21 -07:00
Amos Kong
1cff389ddb mvme147: fix ram size in comment
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.

Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:14:21 -07:00
Julia Lawall
688c3b0033 net/ariadne: delete unneeded call to netdev_priv
Netdev_priv is an accessor function, and has no purpose if its result is
not used.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@ local idexpression x; @@
-x = netdev_priv(...);
... when != x
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 16:57:47 -04:00
Wilfried Klaebe
7ad24ea4bf net: get rid of SET_ETHTOOL_OPS
net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.

Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13 17:43:20 -04:00
Eric W. Biederman
af9ba92cb2 pcnet32: Call dev_kfree_skb_any instead of dev_kfree_skb.
Replace dev_kfree_skb with dev_kfree_skb_any in pcnet32_start_xmit
that can be called in hard irq and other contexts.

dev_kfree_skb_any is used as pcnet32_start_xmit only frees an
skb when it drops a packet during transmit.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2014-03-24 21:18:53 -07:00
Eric W. Biederman
37392c7b84 lance: Call dev_consume_skb_any instead of dev_kfree_skb.
Replace dev_kfree_skb with dev_consume_skb_any in lance_start_xmit
that can be called in hard irq and other contexts.

dev_consume_skb_any is used as lance_start_xmit always immediately
consumes the skb.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2014-03-24 21:18:53 -07:00
Eric W. Biederman
e21106b412 am79c961a: Call dev_consume_skb_any instead of dev_kfree_skb.
Replace dev_kfree_skb with dev_consume_skb_any in am79c961 that can
be called in hard irq and other contexts.

dev_consume_skb_any is used as am79c961_sendpacket always
immediately consumes the skb.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2014-03-24 21:18:40 -07:00
Eric W. Biederman
278d5385b1 amd8111e: Don't receive packets when the napi budget == 0
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-14 22:52:47 -04:00
Don Fry
4cc5c47579 pcnet32: add missing check for pci_dma_mapping_error
The pci_map_single calls never checked for error. Add error checking
as requested by someone last year.  Tested on 79c972.

Signed-off-by: Don Fry <pcnet32@frontier.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-19 14:58:27 -05:00
Don Fry
60e2e8b399 pcnet32: fix reallocation error
pcnet32_realloc_rx_ring() only worked on the first log2 number of
entries in the receive ring instead of the all the entries.
Replaced "1 << size" with more descriptive variable.
This is my original bug from 2006.  Found while testing another problem.
Tested on 79C972 and 79C976.

Signed-off-by: Don Fry <pcnet32@frontier.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-19 14:58:26 -05:00
Linus Torvalds
4ba9920e5e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) BPF debugger and asm tool by Daniel Borkmann.

 2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.

 3) Correct reciprocal_divide and update users, from Hannes Frederic
    Sowa and Daniel Borkmann.

 4) Currently we only have a "set" operation for the hw timestamp socket
    ioctl, add a "get" operation to match.  From Ben Hutchings.

 5) Add better trace events for debugging driver datapath problems, also
    from Ben Hutchings.

 6) Implement auto corking in TCP, from Eric Dumazet.  Basically, if we
    have a small send and a previous packet is already in the qdisc or
    device queue, defer until TX completion or we get more data.

 7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.

 8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
    Borkmann.

 9) Share IP header compression code between Bluetooth and IEEE802154
    layers, from Jukka Rissanen.

10) Fix ipv6 router reachability probing, from Jiri Benc.

11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.

12) Support tunneling in GRO layer, from Jerry Chu.

13) Allow bonding to be configured fully using netlink, from Scott
    Feldman.

14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
    already get the TCI.  From Atzm Watanabe.

15) New "Heavy Hitter" qdisc, from Terry Lam.

16) Significantly improve the IPSEC support in pktgen, from Fan Du.

17) Allow ipv4 tunnels to cache routes, just like sockets.  From Tom
    Herbert.

18) Add Proportional Integral Enhanced packet scheduler, from Vijay
    Subramanian.

19) Allow openvswitch to mmap'd netlink, from Thomas Graf.

20) Key TCP metrics blobs also by source address, not just destination
    address.  From Christoph Paasch.

21) Support 10G in generic phylib.  From Andy Fleming.

22) Try to short-circuit GRO flow compares using device provided RX
    hash, if provided.  From Tom Herbert.

The wireless and netfilter folks have been busy little bees too.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
  net/cxgb4: Fix referencing freed adapter
  ipv6: reallocate addrconf router for ipv6 address when lo device up
  fib_frontend: fix possible NULL pointer dereference
  rtnetlink: remove IFLA_BOND_SLAVE definition
  rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
  qlcnic: update version to 5.3.55
  qlcnic: Enhance logic to calculate msix vectors.
  qlcnic: Refactor interrupt coalescing code for all adapters.
  qlcnic: Update poll controller code path
  qlcnic: Interrupt code cleanup
  qlcnic: Enhance Tx timeout debugging.
  qlcnic: Use bool for rx_mac_learn.
  bonding: fix u64 division
  rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
  sfc: Use the correct maximum TX DMA ring size for SFC9100
  Add Shradha Shah as the sfc driver maintainer.
  net/vxlan: Share RX skb de-marking and checksum checks with ovs
  tulip: cleanup by using ARRAY_SIZE()
  ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
  net/cxgb4: Don't retrieve stats during recovery
  ...
2014-01-25 11:17:34 -08:00
Paul Gortmaker
a81ab36bf5 drivers/net: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.   Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

This covers everything under drivers/net except for wireless, which
has been submitted separately.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-16 11:53:26 -08:00
Geert Uytterhoeven
f187055964 net: amd8111e: Spelling s/recive/receive/
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-14 17:11:25 -08:00
Geert Uytterhoeven
4ffa8fcd17 net/7990: Make lance_private.name const
This allows to drop a few casts.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-29 00:46:38 -05:00
Geert Uytterhoeven
a8ab77a83a net/7990: Fix whitespace errors
Most of them reported by checkpatch.pl

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-29 00:46:38 -05:00
dingtianhong
ebff7b41b6 net: pcnet: slight optimization of addr compare
Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Don Fry <pcnet32@frontier.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-26 13:31:33 -05:00
Jeff Kirsher
0ab75ae81d ethernet: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment.  Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.

CC: Santosh Raspatur <santosh@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Olof Johansson <olof@lixom.net>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Nicolas Pitre <nico@fluxnic.net>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-06 12:37:55 -05:00
Geert Uytterhoeven
bd9ba8f40e zorro/UAPI: Use proper types (endianness/size) in <linux/zorro.h>
Fix member definitions for non-native userspace handling:
  - All multi-byte values are big-endian, hence use __be*,
  - All pointers are 32-bit pointers under AmigaOS, but unused (except for
    cd_BoardAddr) under Linux, hence use __be32.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-11-26 11:09:09 +01:00
Geert Uytterhoeven
6112ea0862 zorro: ZTWO_VADDR() should return "void __iomem *"
ZTWO_VADDR() converts from physical to virtual I/O addresses, so it should
return "void __iomem *" instead of "unsigned long".

This allows to drop several casts, but requires adding a few casts to
accomodate legacy driver frameworks that store "unsigned long" I/O
addresses.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-11-26 11:09:07 +01:00
Linus Torvalds
42a2d923cc Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) The addition of nftables.  No longer will we need protocol aware
    firewall filtering modules, it can all live in userspace.

    At the core of nftables is a, for lack of a better term, virtual
    machine that executes byte codes to inspect packet or metadata
    (arriving interface index, etc.) and make verdict decisions.

    Besides support for loading packet contents and comparing them, the
    interpreter supports lookups in various datastructures as
    fundamental operations.  For example sets are supports, and
    therefore one could create a set of whitelist IP address entries
    which have ACCEPT verdicts attached to them, and use the appropriate
    byte codes to do such lookups.

    Since the interpreted code is composed in userspace, userspace can
    do things like optimize things before giving it to the kernel.

    Another major improvement is the capability of atomically updating
    portions of the ruleset.  In the existing netfilter implementation,
    one has to update the entire rule set in order to make a change and
    this is very expensive.

    Userspace tools exist to create nftables rules using existing
    netfilter rule sets, but both kernel implementations will need to
    co-exist for quite some time as we transition from the old to the
    new stuff.

    Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
    worked so hard on this.

 2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
    to our pseudo-random number generator, mostly used for things like
    UDP port randomization and netfitler, amongst other things.

    In particular the taus88 generater is updated to taus113, and test
    cases are added.

 3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
    and Yang Yingliang.

 4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
    Sujir.

 5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
    Neal Cardwell, and Yuchung Cheng.

 6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
    control message data, much like other socket option attributes.
    From Francesco Fusco.

 7) Allow applications to specify a cap on the rate computed
    automatically by the kernel for pacing flows, via a new
    SO_MAX_PACING_RATE socket option.  From Eric Dumazet.

 8) Make the initial autotuned send buffer sizing in TCP more closely
    reflect actual needs, from Eric Dumazet.

 9) Currently early socket demux only happens for TCP sockets, but we
    can do it for connected UDP sockets too.  Implementation from Shawn
    Bohrer.

10) Refactor inet socket demux with the goal of improving hash demux
    performance for listening sockets.  With the main goals being able
    to use RCU lookups on even request sockets, and eliminating the
    listening lock contention.  From Eric Dumazet.

11) The bonding layer has many demuxes in it's fast path, and an RCU
    conversion was started back in 3.11, several changes here extend the
    RCU usage to even more locations.  From Ding Tianhong and Wang
    Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
    Falico.

12) Allow stackability of segmentation offloads to, in particular, allow
    segmentation offloading over tunnels.  From Eric Dumazet.

13) Significantly improve the handling of secret keys we input into the
    various hash functions in the inet hashtables, TCP fast open, as
    well as syncookies.  From Hannes Frederic Sowa.  The key fundamental
    operation is "net_get_random_once()" which uses static keys.

    Hannes even extended this to ipv4/ipv6 fragmentation handling and
    our generic flow dissector.

14) The generic driver layer takes care now to set the driver data to
    NULL on device removal, so it's no longer necessary for drivers to
    explicitly set it to NULL any more.  Many drivers have been cleaned
    up in this way, from Jingoo Han.

15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.

16) Improve CRC32 interfaces and generic SKB checksum iterators so that
    SCTP's checksumming can more cleanly be handled.  Also from Daniel
    Borkmann.

17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
    using the interface MTU value.  This helps avoid PMTU attacks,
    particularly on DNS servers.  From Hannes Frederic Sowa.

18) Use generic XPS for transmit queue steering rather than internal
    (re-)implementation in virtio-net.  From Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
  random32: add test cases for taus113 implementation
  random32: upgrade taus88 generator to taus113 from errata paper
  random32: move rnd_state to linux/random.h
  random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
  random32: add periodic reseeding
  random32: fix off-by-one in seeding requirement
  PHY: Add RTL8201CP phy_driver to realtek
  xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
  macmace: add missing platform_set_drvdata() in mace_probe()
  ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
  ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
  vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
  ixgbe: add warning when max_vfs is out of range.
  igb: Update link modes display in ethtool
  netfilter: push reasm skb through instead of original frag skbs
  ip6_output: fragment outgoing reassembled skb properly
  MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
  net_sched: tbf: support of 64bit rates
  ixgbe: deleting dfwd stations out of order can cause null ptr deref
  ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
  ...
2013-11-13 17:40:34 +09:00
Maciej W. Rozycki
0fabe1021f MIPS: DECstation I/O ASIC DMA interrupt classes
This change complements commits d0da7c002f7b2a93582187a9e3f73891a01d8ee4
[MIPS: DEC: Convert to new irq_chip functions] and
5359b938c0 [MIPS: DECstation I/O ASIC DMA
interrupt handling fix] and implements automatic handling of the two
classes of DMA interrupts the I/O ASIC implements, informational and
errors.

Informational DMA interrupts do not stop the transfer and use the
`handle_edge_irq' handler that clears the request right away so that
another request may be recorded while the previous is being handled.

DMA error interrupts stop the transfer and require a corrective action
before DMA can be reenabled.  Therefore they use the `handle_fasteoi_irq'
handler that only clears the request on the way out.  Because MIPS
processor interrupt inputs, one of which the I/O ASIC's interrupt
controller is cascaded to, are level-triggered it is recommended that
error DMA interrupt action handlers are registered with the IRQF_ONESHOT
flag set so that they are run with the interrupt line masked.

This change removes the export of clear_ioasic_dma_irq that now does not
have to be called by device drivers to clear interrupts explicitly
anymore.  Originally these interrupts were cleared in the .end handler of
the `irq_chip' structure, before it was removed.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-10-29 21:24:42 +01:00
Jingoo Han
94ee39fe77 net: amd8111e: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18 00:03:29 -04:00
Jingoo Han
3638d30a0b net: pcnet32: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Don Fry <pcnet32@frontier.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-18 00:03:29 -04:00
Joe Perches
d458cdf712 net:drivers/net: Miscellaneous conversions to ETH_ALEN
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.

Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02 17:04:45 -04:00
Nate Levesque
f0e28d48c8 lance: Fix hardcoded interrupt name lp->name to use system device value
The lance interrupt handler was using the hard-coded name which would make it difficult to tell where the interrupt came from. Changed to use the device name that made the interrupt.

Signed-off-by: Nate Levesque <thenaterhood@gmail.com>
Reviewed-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:38:32 -04:00
Joe Perches
44da5c2f52 amd/7990: Remove extern from function prototypes
There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.

Signed-off-by: Joe Perches <joe@perches.com>
2013-09-24 10:10:31 -04:00
Maciej W. Rozycki
19717d0584 declance: Remove `incompatible pointer type' warnings
Revert damage caused by 43d620c829:

.../declance.c: In function 'cp_to_buf':
.../declance.c:347: warning: assignment from incompatible pointer type
.../declance.c:348: warning: assignment from incompatible pointer type
.../declance.c: In function 'cp_from_buf':
.../declance.c:406: warning: assignment from incompatible pointer type
.../declance.c:407: warning: assignment from incompatible pointer type

Also add a `const' qualifier where applicable and adjust formatting.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-20 14:41:03 -04:00
Linus Torvalds
b75ff5e84b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) If the local_df boolean is set on an SKB we have to allocate a
    unique ID even if IP_DF is set in the ipv4 headers, from Ansis
    Atteka.

 2) Some fixups for the new chipset support that went into the sfc
    driver, from Ben Hutchings.

 3) Because SCTP bypasses a good chunk of, and actually duplicates, the
    logic of the ipv6 output path, some IPSEC things don't get done
    properly.  Integrate SCTP better into the ipv6 output path so that
    these problems are fixed and such issues don't get missed in the
    future either.  From Daniel Borkmann.

 4) Fix skge regressions added by the DMA mapping error return checking
    added in v3.10, from Mikulas Patocka.

 5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.

 6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.

 7) Fix error handling in tun_set_iff(), in particular don't leak
    resources.  From Jason Wang.

 8) Prevent format-string injection into xen-netback driver, from Kees
    Cook.

 9) Fix regression added to netpoll ARP packet handling, in particular
    check for the right ETH_P_ARP protocol code.  From Sonic Zhang.

10) Try to deal with AMD IOMMU errors when using r8169 chips, from
    Francois Romieu.

11) Cure freezes due to recent changes in the rt2x00 wireless driver,
    from Stanislaw Gruszka.

12) Don't do SPI transfers (which can sleep) in interrupt context in
    cw1200 driver, from Solomon Peachy.

13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
    From Nithin Sujir.

14) Make xen_netbk_count_skb_slots() count the actual number of slots
    that will be used, taking into consideration packing and other
    issues that the transmit path will run into.  From David Vrabel.

15) Use the correct maximum age when calculating the bridge
    message_age_timer, from Chris Healy.

16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
    Khoroshilov.

17) Netfilter conntrack extensions were converted to RCU but are not
    always freed properly using kfree_rcu().  Fix from Michal Kubecek.

18) VF reset recovery not being done correctly in qlcnic driver, from
    Manish Chopra.

19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.

20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.

21) Internal switch not initialized properly in bgmac driver, from Rafał
    Miłecki.

22) Netlink messages report wrong local and remote addresses in IPv6
    tunneling, from Ding Zhi.

23) ICMP redirects should not generate socket errors in DCCP and SCTP.
    We're still working out how this should be handled for RAW and UDP
    sockets.  From Daniel Borkmann and Duan Jiong.

24) We've had several bugs wherein the network namespace's loopback
    device gets accessed after it is free'd, NULL it out so that we can
    catch these problems more readily.  From Eric W Biederman.

25) Fix regression in TCP RTO calculations, from Neal Cardwell.

26) Fix too early free of xen-netback network device when VIFs still
    exist.  From Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
  netconsole: fix a deadlock with rtnl and netconsole's mutex
  netpoll: fix NULL pointer dereference in netpoll_cleanup
  skge: fix broken driver
  ip: generate unique IP identificator if local fragmentation is allowed
  ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
  xen-netback: Don't destroy the netdev until the vif is shut down
  net:dccp: do not report ICMP redirects to user space
  cnic: Fix crash in cnic_bnx2x_service_kcq()
  bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
  vxlan: Avoid creating fdb entry with NULL destination
  tcp: fix RTO calculated from cached RTT
  drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
  net loopback: Set loopback_dev to NULL when freed
  batman-adv: set the TAG flag for the vid passed to BLA
  netfilter: nfnetlink_queue: use network skb for sequence adjustment
  net: sctp: rfc4443: do not report ICMP redirects to user space
  net: usb: cdc_ether: use usb.h macros whenever possible
  net: usb: cdc_ether: fix checkpatch errors and warnings
  net: usb: cdc_ether: Use wwan interface for Telit modules
  ip6_tunnels: raddr and laddr are inverted in nl msg
  ...
2013-09-19 13:57:28 -05:00
Maciej W. Rozycki
5359b938c0 MIPS: DECstation I/O ASIC DMA interrupt handling fix
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-09-13 11:57:40 +02:00
Michael Opdenacker
7bebd005af ethernet: amd: remove deprecated IRQF_DISABLED
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/amd/sun3lance.c

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-12 23:27:09 -04:00
Linus Torvalds
cc998ff881 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking changes from David Miller:
 "Noteworthy changes this time around:

   1) Multicast rejoin support for team driver, from Jiri Pirko.

   2) Centralize and simplify TCP RTT measurement handling in order to
      reduce the impact of bad RTO seeding from SYN/ACKs.  Also, when
      both timestamps and local RTT measurements are available prefer
      the later because there are broken middleware devices which
      scramble the timestamp.

      From Yuchung Cheng.

   3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
      memory consumed to queue up unsend user data.  From Eric Dumazet.

   4) Add a "physical port ID" abstraction for network devices, from
      Jiri Pirko.

   5) Add a "suppress" operation to influence fib_rules lookups, from
      Stefan Tomanek.

   6) Add a networking development FAQ, from Paul Gortmaker.

   7) Extend the information provided by tcp_probe and add ipv6 support,
      from Daniel Borkmann.

   8) Use RCU locking more extensively in openvswitch data paths, from
      Pravin B Shelar.

   9) Add SCTP support to openvswitch, from Joe Stringer.

  10) Add EF10 chip support to SFC driver, from Ben Hutchings.

  11) Add new SYNPROXY netfilter target, from Patrick McHardy.

  12) Compute a rate approximation for sending in TCP sockets, and use
      this to more intelligently coalesce TSO frames.  Furthermore, add
      a new packet scheduler which takes advantage of this estimate when
      available.  From Eric Dumazet.

  13) Allow AF_PACKET fanouts with random selection, from Daniel
      Borkmann.

  14) Add ipv6 support to vxlan driver, from Cong Wang"

Resolved conflicts as per discussion.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
  openvswitch: Fix alignment of struct sw_flow_key.
  netfilter: Fix build errors with xt_socket.c
  tcp: Add missing braces to do_tcp_setsockopt
  caif: Add missing braces to multiline if in cfctrl_linkup_request
  bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
  vxlan: Fix kernel panic on device delete.
  net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
  net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
  icplus: Use netif_running to determine device state
  ethernet/arc/arc_emac: Fix huge delays in large file copies
  tuntap: orphan frags before trying to set tx timestamp
  tuntap: purge socket error queue on detach
  qlcnic: use standard NAPI weights
  ipv6:introduce function to find route for redirect
  bnx2x: VF RSS support - VF side
  bnx2x: VF RSS support - PF side
  vxlan: Notify drivers for listening UDP port changes
  net: usbnet: update addr_assign_type if appropriate
  driver/net: enic: update enic maintainers and driver
  driver/net: enic: Exposing symbols for Cisco's low latency driver
  ...
2013-09-05 14:54:29 -07:00
Jingoo Han
1fc2c469ae net: au1000_eth: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-30 17:43:35 -04:00
Joe Perches
1409a93274 ethernet: Convert mac address uses of 6 to ETH_ALEN
Use the normal #define to help grep find mac addresses
and ensure that addresses are aligned.

pasemi.h has an unaligned access to mac_addr, unchanged
for now.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Olof Johansson <olof@lixom.net> # pasemi_mac pieces
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-02 12:33:54 -07:00
Rusty Russell
8c6ffba0ed PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
Sweep of the simple cases.

Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-07-15 11:25:01 +09:30
Yijing Wang
f9c7da5eaf amd8111e: use pdev->pm_cap instead of pci_find_capability(.., PCI_CAP_ID_PM)
Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: netdev@vger.kernel.org (open list:NETWORKING DRIVERS)
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-19 22:22:56 -07:00
Ben Hutchings
a1606c7dc6 net: Move MII out from under NET_CORE and hide it
All drivers that select MII also need to select NET_CORE because MII
depends on it.  This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.

There is also no need for it to be a visible option, since its users
all select it.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-19 22:22:56 -07:00
Jingoo Han
dfd93c977d net: ethernet: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-27 22:34:51 -07:00
Jingoo Han
8513fbd880 net: ethernet: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-25 21:27:58 -07:00
Peter Hüwe
a46e6ccdd1 net/ethernet/amd/amd8111e: Use module_pci_driver to register driver
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-22 14:35:05 -07:00
Linus Torvalds
73287a43cc Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights (1721 non-merge commits, this has to be a record of some
  sort):

   1) Add 'random' mode to team driver, from Jiri Pirko and Eric
      Dumazet.

   2) Make it so that any driver that supports configuration of multiple
      MAC addresses can provide the forwarding database add and del
      calls by providing a default implementation and hooking that up if
      the driver doesn't have an explicit set of handlers.  From Vlad
      Yasevich.

   3) Support GSO segmentation over tunnels and other encapsulating
      devices such as VXLAN, from Pravin B Shelar.

   4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.

   5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
      Dukkipati.

   6) In the PHY layer, allow supporting wake-on-lan in situations where
      the PHY registers have to be written for it to be configured.

      Use it to support wake-on-lan in mv643xx_eth.

      From Michael Stapelberg.

   7) Significantly improve firewire IPV6 support, from YOSHIFUJI
      Hideaki.

   8) Allow multiple packets to be sent in a single transmission using
      network coding in batman-adv, from Martin Hundebøll.

   9) Add support for T5 cxgb4 chips, from Santosh Rastapur.

  10) Generalize the VXLAN forwarding tables so that there is more
      flexibility in configurating various aspects of the endpoints.
      From David Stevens.

  11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
      from Dmitry Kravkov.

  12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
      Neira Ayuso.

  13) Start adding networking selftests.

  14) In situations of overload on the same AF_PACKET fanout socket, or
      per-cpu packet receive queue, minimize drop by distributing the
      load to other cpus/fanouts.  From Willem de Bruijn and Eric
      Dumazet.

  15) Add support for new payload offset BPF instruction, from Daniel
      Borkmann.

  16) Convert several drivers over to mdoule_platform_driver(), from
      Sachin Kamat.

  17) Provide a minimal BPF JIT image disassembler userspace tool, from
      Daniel Borkmann.

  18) Rewrite F-RTO implementation in TCP to match the final
      specification of it in RFC4138 and RFC5682.  From Yuchung Cheng.

  19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
      you like netlink, so I implemented netlink dumping of netlink
      sockets.") From Andrey Vagin.

  20) Remove ugly passing of rtnetlink attributes into rtnl_doit
      functions, from Thomas Graf.

  21) Allow userspace to be able to see if a configuration change occurs
      in the middle of an address or device list dump, from Nicolas
      Dichtel.

  22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
      Frederic Sowa.

  23) Increase accuracy of packet length used by packet scheduler, from
      Jason Wang.

  24) Beginning set of changes to make ipv4/ipv6 fragment handling more
      scalable and less susceptible to overload and locking contention,
      from Jesper Dangaard Brouer.

  25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
      instead.  From Hong Zhiguo.

  26) Optimize route usage in IPVS by avoiding reference counting where
      possible, from Julian Anastasov.

  27) Convert IPVS schedulers to RCU, also from Julian Anastasov.

  28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
      Eitzenberger.

  29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
      nfnetlink_log, and nfnetlink_queue.  From Gao feng.

  30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.

  31) Support several new r8169 chips, from Hayes Wang.

  32) Support tokenized interface identifiers in ipv6, from Daniel
      Borkmann.

  33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.

  34) Add 802.1ad vlan offload support, from Patrick McHardy.

  35) Support mmap() based netlink communication, also from Patrick
      McHardy.

  36) Support HW timestamping in mlx4 driver, from Amir Vadai.

  37) Rationalize AF_PACKET packet timestamping when transmitting, from
      Willem de Bruijn and Daniel Borkmann.

  38) Bring parity to what's provided by /proc/net/packet socket dumping
      and the info provided by netlink socket dumping of AF_PACKET
      sockets.  From Nicolas Dichtel.

  39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
      Poirier"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
  filter: fix va_list build error
  af_unix: fix a fatal race with bit fields
  bnx2x: Prevent memory leak when cnic is absent
  bnx2x: correct reading of speed capabilities
  net: sctp: attribute printl with __printf for gcc fmt checks
  netlink: kconfig: move mmap i/o into netlink kconfig
  netpoll: convert mutex into a semaphore
  netlink: Fix skb ref counting.
  net_sched: act_ipt forward compat with xtables
  mlx4_en: fix a build error on 32bit arches
  Revert "bnx2x: allow nvram test to run when device is down"
  bridge: avoid OOPS if root port not found
  drivers: net: cpsw: fix kernel warn on cpsw irq enable
  sh_eth: use random MAC address if no valid one supplied
  3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
  tg3: fix to append hardware time stamping flags
  unix/stream: fix peeking with an offset larger than data in queue
  unix/dgram: fix peeking with an offset larger than data in queue
  unix/dgram: peek beyond 0-sized skbs
  openvswitch: Remove unneeded ovs_netdev_get_ifindex()
  ...
2013-05-01 14:08:52 -07:00
Patrick McHardy
86a9bad3ab net: vlan: add protocol argument to packet tagging functions
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:46:06 -04:00
Patrick McHardy
f646968f8f net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:26 -04:00
H Hartley Sweeten
fdd3f29edd drivers/net: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:27:33 -07:00
Joe Perches
d0320f7500 drivers:net: Remove dma_alloc_coherent OOM messages
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-15 08:56:58 -04:00
Silviu-Mihai Popescu
3ffd880d3c ethernet: amd: use PTR_RET instead of IS_ERR + PTR_ERR
This uses PTR_RET instead of IS_ERR and PTR_ERR in order to increase
readability.

Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: <Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-12 06:57:22 -04:00
Joe Perches
720a43efd3 drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.

Other trivial changes around these removals:

Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-09 16:09:19 -05:00
Joe Perches
14f8dc4953 drivers: net: Remove remaining alloc/OOM messages
alloc failures already get standardized OOM
messages and a dump_stack.

For the affected mallocs around these OOM messages:

Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08 17:44:39 -05:00
Paul Gortmaker
1f1c7a5c1d drivers/net: delete old DEC depca ISA drivers support.
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them.  Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2013-01-22 10:39:55 -05:00
Florian Fainelli
f9a8f83b04 net: phy: remove flags argument from phy_{attach, connect, connect_direct}
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.

Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 15:11:50 -05:00
Jiri Pirko
aaeb6cdfa5 remove init of dev->perm_addr in drivers
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-08 18:00:48 -08:00
Paul Gortmaker
483f777266 drivers/net: remove orphaned references to micro channel
We threw away the microchannel support, but the removal wasn't
completely trivial since there was namespace overlap with the
machine check support, and hence some orphaned dependencies
survived the deletion.  This attempts to sweep those up and
send them to the bit-bucket.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-06 21:13:33 -08:00
Jiri Pirko
7826d43f2d ethtool: fix drvinfo strings set in drivers
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-06 21:06:31 -08:00
Greg Kroah-Hartman
1dd06ae8db drivers/net: fix up function prototypes after __dev* removals
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-07 14:22:22 -05:00
Bill Pemberton
0cb0568dfe net/amd: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-12-03 11:16:54 -08:00
Bill Pemberton
a9590879e1 pcnet32: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-12-03 11:16:41 -08:00
Bill Pemberton
92a66593e5 drivers/net/ethernet/amd/am79c961a.c: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-12-03 11:16:12 -08:00
Peter Senna Tschudin
691299201b drivers/net/ethernet/amd/au1000_eth.c: fix error return code
The function au1000_probe() return 0 for success and negative value
for most of its internal tests failures. There are exceptions
that are error cases going to err_out:. For this cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-07 14:37:11 -04:00
Peter Senna Tschudin
86e506e399 drivers/net/ethernet/amd/amd8111e.c: fix error return code
The function amd8111e_probe_one() return 0 for success and negative
value for most of its internal tests failures. There are two exceptions
that are error cases going to err_free_reg:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.

This patch fixes the error cases that do not return negative values.

This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.

A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-07 14:37:11 -04:00
Jon Mason
5c8b73ca43 lance: remove unnecessary setting of skb->dev
skb->dev is being unnecessarily set during ring init.  It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-10 23:24:56 -07:00
Joe Perches
6469933605 ethernet: Remove casts to same type
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.

For example, this cast:

        int y;
        int *p = (int *)&y;

I used the coccinelle script below to find and remove these
unnecessary casts.  I manually removed the conversions this
script produces of casts with __force, __iomem and __user.

@@
type T;
T *p;
@@

-       (T *)p
+       p

A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.

Change the argument to a non-const pointer.

A function in stmmac needed a __force to avoid a sparse
warning.  Added it.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-06 09:31:33 -07:00
Linus Torvalds
881bcabbde Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Setup CROSS_COMPILE at the top
  m68k: Correct the Atari ALLOWINT definition
  m68k/video: Create <asm/vga.h>
  m68k: Make sure {read,write}s[bwl]() are always defined
  m68k/mm: Port OOM changes to do_page_fault()
  scsi/atari: Make more functions static
  scsi/atari: Revive "atascsi=" setup option
  net/ariadne: Improve debug prints
  m68k/atari: Change VME irq numbers from unsigned long to unsigned int
  m68k/amiga: Use arch_initcall() for registering platform devices
  m68k/amiga: Add error checks when registering platform devices
  m68k/amiga: Mark z_dev_present() __init
  m68k: Remove unused MAX_NOINT_IPL definition
2012-05-21 12:43:54 -07:00
Paul Gortmaker
a5e371f61a drivers/net: delete all code/drivers depending on CONFIG_MCA
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.

This commit removes any MCA specific net drivers, and removes
any MCA specific probe/support code from drivers that were
doing a dual ISA/MCA role.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-05-17 16:37:41 -04:00
Joe Perches
2e42e4747e drivers/net: Convert compare_ether_addr to ether_addr_equal
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-10 23:33:01 -04:00
Geert Uytterhoeven
0eb8694b18 net/ariadne: Improve debug prints
Remove casts and use proper printf()-style format specifiers instead.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
2012-04-22 20:16:49 +02:00
Geert Uytterhoeven
44883eb023 m68k/atari: Change VME irq numbers from unsigned long to unsigned int
Device interrupts numbers were changed to unsigned int in 1997, the year
IRQ_MACHSPEC was killed as well.

Also kill a related cast while we're at it.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: netdev@vger.kernel.org
2012-04-22 20:16:49 +02:00
David Howells
9ffc93f203 Remove all #inclusions of asm/system.h
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`

Signed-off-by: David Howells <dhowells@redhat.com>
2012-03-28 18:30:03 +01:00
Danny Kukawka
f27fd49962 amd/hplance.c: print MAC via printk format specifier
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.

Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-24 15:40:59 -05:00
Danny Kukawka
7718f2c27d au1000_eth: use eth_hw_addr_random() instead of random_ether_addr()
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

v2: adapt to eth_hw_addr_random()

Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-17 15:52:30 -05:00
Pradeep A Dalvi
1d26643054 netdev: ethernet dev_alloc_skb to netdev_alloc_skb
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
  - Removed extra skb->dev = dev after netdev_alloc_skb

Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-06 11:41:20 -05:00
Joe Perches
41de8d4cff drivers/net: Remove alloc_etherdev error messages
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31 16:20:48 -05:00
Joe Perches
e404decb0f drivers/net: Remove unnecessary k.alloc/v.alloc OOM messages
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.

Remove the allocation failure messages.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31 16:20:21 -05:00
Paul Gortmaker
3396c7823e drivers/net: fix up stale paths from driver reorg
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text.  Bring them up to date.  No actual change to
any code takes place here.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-30 12:54:40 -05:00
Florian Fainelli
f74299b6c1 au1000-eth: use an unique MDIO bus name.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-10 16:35:00 -08:00
Rusty Russell
eb93992207 module_param: make bool parameters really bool (net & drivers/net)
module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.

(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-19 22:27:29 -05:00
Axel Lin
db62f684de net/ethernet: convert drivers/net/ethernet/* to use module_platform_driver()
This patch converts the drivers in drivers/net/ethernet/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-29 00:25:05 -05:00
Joe Perches
c857ff6ece amd8111e: Convert ETH_ADDR_LEN uses to ETH_ALEN
Reduce the number of #defines, use the normal #define from if_ether.h

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16 20:23:18 -05:00
Joe Perches
104bf3fb96 ethernet: Convert ETHER_ADDR_LEN uses to ETH_ALEN
Reduce the number of #defines, use the normal #define from if_ether.h

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16 20:23:17 -05:00
Rick Jones
33a5ba144e net: sweep-up some straglers in strlcpy conversion of .get_drvinfo routines
Convert some remaining straglers' .get_drvinfo routines to use strlcpy
rather than strcpy/strncpy.

Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16 17:38:55 -05:00
Rick Jones
23020ab353 Sweep additional floors of strcpy in .get_drvinfo routines
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.

Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-14 00:35:46 -05:00
Linus Torvalds
d6748066ad Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits)
  MIPS: O32: Provide definition of registers ta0 .. ta3.
  MIPS: perf: Add Octeon support for hardware perf.
  MIPS: perf: Add support for 64-bit perf counters.
  MIPS: perf: Reorganize contents of perf support files.
  MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c
  MIPS: Add accessor macros for 64-bit performance counter registers.
  MIPS: Add probes for more Octeon II CPUs.
  MIPS: Add more CPU identifiers for Octeon II CPUs.
  MIPS: XLR, XLS: Add comment for smp setup
  MIPS: JZ4740: GPIO: Check correct IRQ in demux handler
  MIPS: JZ4740: GPIO: Simplify IRQ demuxer
  MIPS: JZ4740: Use generic irq chip
  MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
  MIPS: Alchemy: kill au1xxx.h header
  MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines
  MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep
  MIPS: Alchemy: Redo PCI as platform driver
  MIPS: Alchemy: more base address cleanup
  MIPS: Alchemy: rewrite USB platform setup.
  MIPS: Alchemy: abstract USB block control register access
  ...

Fix up trivial conflicts in:
	arch/mips/alchemy/devboards/db1x00/platform.c
	drivers/ide/Kconfig
	drivers/mmc/host/au1xmmc.c
	drivers/video/Kconfig
	sound/mips/Kconfig
2011-11-03 13:28:14 -07:00
françois romieu
5d472b7377 drivers/net/ethernet: remove unused #define.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-03 14:09:10 -04:00
David S. Miller
8decf86879 Merge branch 'master' of github.com:davem330/net
Conflicts:
	MAINTAINERS
	drivers/net/Kconfig
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
	drivers/net/ethernet/broadcom/tg3.c
	drivers/net/wireless/iwlwifi/iwl-pci.c
	drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c
	drivers/net/wireless/rt2x00/rt2800usb.c
	drivers/net/wireless/wl12xx/main.c
2011-09-22 03:23:13 -04:00
stephen hemminger
1d70cb06db pcnet32: constify function table
Function tables need to be const to prevent malicious use.

This is compile tested only.
Gleaned from PAX.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16 19:20:20 -04:00
Jeff Kirsher
aaba215ca0 MII: fix Kconfig dependencies for MII
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well.  It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled.  This caused a dependency error.

Resolved the dependency by selecting NET_CORE when MII is
selected.

Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15 15:49:08 -04:00
Jeff Kirsher
88f07484cc drivers/net/ethernet/*: Enabled vendor Kconfig options
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.

This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers.  In
addition, by enabling all the new Kconfig options does not add
any un-expected options.

CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-27 00:58:56 -07:00
David S. Miller
823dcd2506 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net 2011-08-20 10:39:12 -07:00
Jiri Pirko
afc4b13df1 net: remove use of ndo_set_multicast_list in drivers
replace it by ndo_set_rx_mode

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17 20:22:03 -07:00
Jeff Kirsher
b955f6ca77 amd: Move AMD (Lance) chipset drivers
Moves the drivers for the AMD chipsets into drivers/net/ethernet/amd/
and the necessary Kconfig and Makfile changes.

The au1000 (Alchemy) driver was also moved into the same directory
even though it is not a "Lance" driver.

CC: Peter Maydell <pmaydell@chiark.greenend.org.uk>
CC: Roman Hodek <Roman.Hodek@informatik.uni-erlangen.de>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
CC: Donald Becker <becker@scyld.com>
CC: Sam Creasey <sammy@users.qual.net>
CC: Miguel de Icaza <miguel@nuclecu.unam.mx>
CC: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CC: Don Fry <pcnet32@frontier.com>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: David Davies <davies@maniac.ultranet.com>
CC: "M.Hipp" <hippm@informatik.uni-tuebingen.de>
CC: Pete Popov <ppopov@embeddedalley.com>
CC: David Hinds <dahinds@users.sourceforge.net>
CC: "Roger C. Pao" <rpao@paonet.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-10 19:54:11 -07:00