We need to check netif_running() state in most ethtool operations
and properly handle the !netif_running() state where the chip is
in an uninitailzed state or low power state that may not accept
any MMIO.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This logic is used in bnx2_close() and bnx2_suspend() and
so should be separated out into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/jme.c:1598: warning: ‘jme_set_100m_half’ defined but not used
drivers/net/jme.c:1618: warning: ‘jme_wait_link’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
Advances the driver version after modification.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix IRQ handle bug when interrupt mode.
The driver was incorrectly handled and returned IRQ_HANDLED
while the device is not generating the interrupt.
It happened due to faulty determination of interrupt status register.
Found by: "Ethan" <ethanhsiao@jmicron.com>
Fixed by: "akeemting" <akeem@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Set bit 5 of GPREG1 to 1 to enable hardware workaround for half-duplex
mode. Which the MAC processor generates CRS/COL by itself instead of
receive it from PHY processor.
2. Set bit 6 of GPREG1 to 1 to enable hardware workaround that masks the
MAC processor working right while calculating IPv6 RSS in 10/100
mode.
3. Group the workaround codes all together.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SR PHY.
Auto-detect phy module type, and report type changes.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic code to manage interrupt driven PHYs.
Do not reset the phy after link parameters update,
the new values might get lost.
Return early from link change notification
when the link parameters remain unchanged.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not require PHY interrupts to be connected to GPIs in ascending order.
Base interrupt availability both on PHYs supporting them and on GPIs being
hooked up. Allows boards to specify interrupt GPIs though the PHYs don't
use them.
Remove spurious PHY interrupts due to clearing T3DBG interrupts before
setting their polarity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second step in overall phy layer reorganization.
Clean up the port_type_info structure.
Support coextistence of clause 22 and clause 45 MDIO devices.
Select the type of MDIO transaction on a per transaction basis.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step towards overall PHY layering re-organization.
Allow a status return when a PHY is reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a queue set per core, up to the maximum of available qsets.
Share the queue sets on multi port adapters.
Rename MSI-X interrupt vectors ethX-N, N being the queue set number.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when a fatal error occurs, bring ports down, reset the chip,
and bring ports back up.
Factorize code used for both EEH and fatal error recovery.
Fix timer usage when bringing up/resetting sge queue sets.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The write barrier should be used before starting a DMA transfer. This fixes
a problem, where almost all packets received on another machine had garbled
content. Tested with an RTL8100C on a MIPS machine.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
there's several drivers that have use "tx_timeout" for the .. tx
timeout function. All fine with that, they're static, however for
doing stats on how often which driver hits the timeout it's a tad
unfortunate. The patch below gives the ones I found in the
kerneloops.org database unique names.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with CONFIG_USB_DEBUG, don't create logspam from
the USB networking drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since recent kernel (2.6.26 or 2.6.27) the PCI wakeup functions are
influenced by generic device ability and configuration when enabling
PCI-device triggered wake-up.
This patch causes WoL setting to enable/disable device's wish to
be permitted to wake-up the host when changing WoL options and
also during device probing.
Without this patch one has write 'enabled' to
/sys/bus/pci/devices/0000:02:08.0/power/wakeup
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the chip and handling it's power management settings
also remember wether WoL feature is enabled.
Without this patch one has to call ethtool to change WoL settings
for this flag to be set and any WoL being enabled on suspend to
RAM.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device's carrier status is controlled via the functions
netif_carrier_on() and netif_carrier_off(). These set or clear a bit
indicating the carrier (aka lower level link) is down, and if the state
changed, they fire off a routing netlink event.
Add a call to netif_carrier_off() before register_netdev() so that the
newly created device will be set to carrier down. Then when the carrier
comes up for the first time, a netlink event will be generated, as the
carrier changed from down to up. Otherwise the initial carrier up will
appear to be changing the status from up to up, and so no event is
generated since that's not a change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv643xx_eth uses ip_hdr() (defined in linux/ip.h), but relied on
another header file to include the needed header file indirectly.
In latest net-next this indirect include chain is gone, so the
driver fails to build. Include linux/ip.h explicitly to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lockdep warning:
=================================
[ INFO: inconsistent lock state ]
2.6.27-rc7 #3
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
syslogd/2474 [HC0[0]:SC0[0]:HE1:SE1] takes:
(_xmit_ETHER#2){-+..}, at: [<c0265562>] netpoll_send_skb+0x132/0x190
...
is caused by unconditional local_irq_disable()/local_irq_enable() in
disable_irq_lockdep()/enable_irq_lockdep() used by __ei_poll(). Since
netconsole/netpoll always calls dev->poll_controller() with local irqs
disabled, disable_irq()/enable_irq() instead is safe and enough (like
e.g. in 3c509 or 8139xx drivers).
Reported-and-tested-by: Bernard Pidoux F6BVP <f6bvp@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out by Breno Leitao <leitao@linux.vnet.ibm.com> that
ixgb would crash on PPC when an IOMMU was in use, if change_mtu was
called.
It appears to be a pretty simple issue in the driver that wasn't discovered
because most systems don't run with an IOMMU. The driver needs to only unmap
buffers that are mapped (duh).
CC: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since e1000e has been existance in linux-2.6, we've
never released the hardware semaphore after a successful
write to the SPI EEPROM. I guess we don't write to
SPI EEPROM much -- but those few of us that do appreciate
it when we can later read from the EEPROM without having
to reboot.
Found-by: Nick Van Fossen <Nick.VanFossen@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Reviewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN9500 USB2.0 10/100 ethernet
adapter.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
Add multiqueue TX support to myri10ge.
[ Removed reference to deprecated CONFIG_NETDEVICES_MULTIQUEUE and
NETIF_F_MULTI_QUEUE ]
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the EXPERIMENTAL label from the atl1 driver and change the vendor
name to include Attansic's successor, Atheros. We'll leave Attansic in
the name since Attansic's PCI ID (1969) is encoded in the PCI config and
is what users encounter on their systems.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver
and remove the NETIF_F_LLTX feature flag.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
See http://marc.info/?l=linux-netdev&m=121931988219314&w=2
Stop the queue and turn off carrier to prevent transmit timeouts
when the cable is unplugged/replugged.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return is useful to caller, driver shouldn't miss it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pauseparam is set
On Wednesday 24 September 2008 07:47, Stephen Hemminger wrote:
> On Mon, 22 Sep 2008 14:52:17 -0700
>
> akpm@linux-foundation.org wrote:
> > From: "Xiaoming.Zhang" <Xiaoming.Zhang@resilience.com>
> >
> > We have an issue of the skge driver: The card won't work when it's
> > options are changed. Here's the hardware info:
> >
> > # lspci -v
> > 05:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
> > Gigabit Ethernet Controller (rev 13) Subsystem: Marvell Technology Group
> > Ltd. Marvell RDK-8001 Flags: bus master, 66MHz, medium devsel, latency
> > 32, IRQ 16 Memory at d042c000 (32-bit, non-prefetchable) [size=16K] I/O
> > ports at d000 [size=256]
> > [virtual] Expansion ROM at 20400000 [disabled] [size=128K]
> > Capabilities: [48] Power Management version 2
> > Capabilities: [50] Vital Product Data
> >
> > The happens in both Linux-2.6.26(skge version 1.23) and RHEL5.2(skge
> > version 1.6).
> >
> > For example, at first it is set to "speed 1000 duplex full auto-neg on"
> > and it works, then run
> >
> > ethtool -s <ethx> autoneg off
> > or ethtool -s <ethx> speed 100 duplex full autoneg off
> >
> > Then it will stop working. After that if we restart the interface:
> >
> > ifconifg <ethx> down
> > ifconfig <ethx> up
> >
> > It will work again. And `ethtool -A' has the same issue.
> >
> > So we think after setting the options, the interface should be restarted.
> >
> > Signed-off-by: Zhang Xiaoming <xiaoming.zhang@resilience.com>
> > Cc: Stephen Hemminger <shemminger@vyatta.com>
> > Cc: Jeff Garzik <jeff@garzik.org>
> > Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
> > ---
> >
> > drivers/net/skge.c | 12 ++++++++----
> > 1 file changed, 8 insertions(+), 4 deletions(-)
> >
> > diff -puN
> > drivers/net/skge.c~driver-net-skgec-restart-the-interface-when-its-option
> >s-or-pauseparam-is-set drivers/net/skge.c ---
> > a/drivers/net/skge.c~driver-net-skgec-restart-the-interface-when-its-opti
> >ons-or-pauseparam-is-set +++ a/drivers/net/skge.c
> > @@ -353,8 +353,10 @@ static int skge_set_settings(struct net_
> > skge->autoneg = ecmd->autoneg;
> > skge->advertising = ecmd->advertising;
> >
> > - if (netif_running(dev))
> > - skge_phy_reset(skge);
> > + if (netif_running(dev)) {
> > + skge_down(dev);
> > + skge_up(dev);
> > + }
> >
> > return (0);
> > }
> > @@ -595,8 +597,10 @@ static int skge_set_pauseparam(struct ne
> > skge->flow_control = FLOW_MODE_NONE;
> > }
> >
> > - if (netif_running(dev))
> > - skge_phy_reset(skge);
> > + if (netif_running(dev)) {
> > + skge_down(dev);
> > + skge_up(dev);
> > + }
> >
> > return 0;
> > }
>
> Since skge_up can fail because of out of memory, this code needs to
> check the return value. And then if it fails the "limbo state" needs
> to be handled in skge_down.
How about like this? It is tested.
Thank you.
Signed-off-by: Zhang Xiaoming <xiaoming.zhang@resilience.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SGE queue set timer might access registers while in EEH recovery,
triggering an EEH error loop. Stop all timers early in EEH process.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NETIF_F_LLTX is set, the atlx driver will use a private lock.
But in recent kernels this implementation seems redundant and
can cause problems where AF_PACKET sees things twice. Since
NETIF_F_LLTX is marked as deprecated and shouldn't be used in
new driver, this patch removes NETIF_F_LLTX and adds a mmiowb
before sending packet. I have tested this driver on a Eee PC.
It works well.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's aneg is configured and restarted whenever the link is brought up,
e.g. when DHCP is started after the kernel has booted. This can take the
link down for several seconds while auto-negotiation is redone.
If the advertised features haven't changed, then it shouldn't be necessary
to bring down the link and start auto-negotiation over again.
genphy_config_advert() is enhanced to return 0 when the advertised features
haven't been changed and >0 when they have been.
genphy_config_aneg() then uses this information to not call
genphy_restart_aneg() if there has been no change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netconsole support for Atheros L2 10/100 network device.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes EMAC soft reset on 460EX/GT when no external clock is
available.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. DRCMRxx is no longer recommended, use DRCMR(xx) instead, and
pass DRCMR index by "struct resource" if possible
2. DCSRxx, DDADRxx, DSADRxx, DTADRxx, DCMDxx is never used, use
DCSR(), DDADR(), DSADR(), DTADR(), DCMD() instead
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes STATUS_CONF_PENDING usage that called from
iwl4965_mac_config internally after scan completed.
It's called anyway from the mac80211 ieee80211_scan_completed():
if (local->hw_scanning) {
local->hw_scanning = false;
if (ieee80211_hw_config(local))
...
}
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves comment to proper line, it has moved during
code shuffling.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets rx_chain bitmap correctly according hw configuration.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the tx status reporting, fix retry counters (short retries are
virtual collisions, not actual retries). Implement multi-rate retry
support.
This also fixes strong throughput fluctuations with rc80211_pid
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The state field of the rfkill structure was incorrectly initialized to -1, which results in rfkill
issueing a WARN_ON. Fix this by initializing the state field to the proper value as indicated by
the driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the a few lines that went missing in
"p54: 802.11a 5GHz phy support"
Essentially: the rx-code wasn't updated and therefore reported the wrong band,
but more importantly the rate index was off as well, since 802.11a doesn't
allow the "four" 802.11b rates...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables Adaptive Noise Immunity (ANI) on ath9k.
ANI is as algorithm designed to minimize the detrimental
effects of time-varying interferences. This should
help with throughput in noisy environments. To use
ANI we re-enable the MIB interrupt. Since ANI works
on a timer and updates the noise floor we take
advantage of this and also report a non-static noise
floor now to mac80211.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were trying to hold the wrong spinlock due to a typo
on IEEE80211_BAR_CTL_TID_S's definition. We use this to
compute the tid number and then hold this this tid number's
spinlock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of the cleanup on ath9k -- this was also causing some
annoying compile time warnings.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Found during the (partial) unregister_netdevice audit that we didn't
have to have :)
It looks like a couple of Sun NIC drivers had unregister_netdevice
when they really meant unregister_netdev.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing 'WARN_ON(preempt_count())' was horribly horribly wrong, and would
cause tons of warnings at bootup if PREEMPT was enabled because the
initcalls currently run with the kernel lock, which increments the
preempt count.
At the same time, the warning was also insufficient, since it didn't
check that interrupts were enabled.
The proper debug function to use for something that can sleep and wants
a warning if it's called in the wrong context is 'might_sleep()'.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a mutex to the e1000e driver that would help
catch any collisions of two e1000e threads accessing hardware
at the same time.
description and patch updated by Jesse
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the stats lock is left over from e1000, e1000e no longer
has the adjust tbi stats function that required the addition
of the stats lock to begin with.
adding a mutex to acquire_swflag helped catch this one too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
thanks to tglx, we're finding some interesting reentrancy issues.
this patch removes the phy read from inside a spinlock, paving
the way for removing the spinlock completely. The phy read was
only feeding a statistic that wasn't used.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e1000e was apparently calling two functions that attempted to reserve
the SWFLAG bit for exclusive (to hardware and firmware) access to
the PHY and NVM (aka eeprom). These accesses could possibly call
msleep to wait for the resource which is not allowed from interrupt
context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the process of debugging things, noticed that the swflag is not reset
by the driver after reset, and the swflag is probably not reset unless
management firmware clears it after 100ms.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM. This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for i.MX31ADS board to the cs89x0 ethernet driver.
Rework Kconfig options for the cs89x0 driver to reduce the #ifdef
clutter.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This gives a nice increase in the maximum loss-free packet forwarding
rate in routing workloads.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add support for AR2417 (include pci id) since my previous patch doesn't sit on top of base.c/ath5k.h anymore.
* Update module version to 0.6.0
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix srev reporting during attach
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use QUIET mechanism to drain tx buffer on PCU for newer chips
* Make sure that INTPEND is really 1 and not 0xffffffff while checking for pending interrupts
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use new SREV values and PHY srevs to identify radio type durring attach
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the spin-on-condition loops in routine do_dummy_tx always exits before
the condition is satisfied. The hardware might be left in an inconsistent
state that might be the cause of the PHY transmission errors seen by some
users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update registers
* Update SREV values and add some PHY srevs
* Prepare ath5k.h for newer radios etc
Thanks to Atheros 's HAL source we now know for sure how many parts we have
and what their SREV values are. We also have some updates on registers. Prepare
ath5k for some major updates ;-)
My previous mail had 2 more patches following (git log misusage), sorry for double
posting ;-(
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the newly-released Atheros HAL code, asserting the
TSF reset bit will toggle a hardware internal state, resulting in a
spurious reset on the next chip reset. Whenever we force a TSF bit,
write the bit twice to clear the internal signal.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix by disabling rt2x00 rfkill support when rt2x00 is built-in and rfkill has been modularized, and
a similar scheme for the relationship between leds_class and rt2x00..
Also, give a warning to the end-user when rfkill-/leds-support is disabled this way, so that the
end-user has at least some clues on what is going on.
Proper fixing required some general updates of the Kconfig-structure for the rt2x00 driver, whereby
internal configuration symbols had to be moved to after the user-visible configuration symbols.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses comments from Dan Williams about the patch
committed as "libertas: Improvements on automatic tx power control via
SIOCSIWTXPOW."
Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yet another BCM4306 card with the Bluetooth Coexistence SPROM programming
error has been found.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use correct DMA_MASK: 4964 and 5000 support 36 bit addresses for
pci express memory access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables power save setting from config (iwconfig power)
The sysfs power_level interface is still preserved as it has
mac80211 power implementation is not yet rich enough.
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds HW bug W/A FH_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY so that we
can enable again interrupt coalescing. It also uses named constants for
open code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command
make C=2 CF="-D__CHECK_ENDIAN__" drivers/net/wireless/p54/
generates the following warnings:
.../p54common.c:152:38: warning: incorrect type in argument 1 (different base types)
.../p54common.c:152:38: expected restricted __be32 const [usertype] *p
.../p54common.c:152:38: got unsigned int *<noident>
.../p54common.c:184:15: warning: restricted __le32 degrades to integer
.../p54common.c:185:29: warning: cast to restricted __le16
.../p54common.c:309:11: warning: symbol 'p54_rf_chips' was not declared.
Should it be static?
.../p54common.c:313:5: warning: symbol 'p54_parse_eeprom' was not declared.
Should it be static?
.../p54common.c:620:43: warning: incorrect type in argument 3 (different base types)
.../p54common.c:620:43: expected unsigned long [unsigned] [usertype] len
.../p54common.c:620:43: got restricted __le16 [usertype] len
.../p54common.c:780:41: warning: restricted __le16 degrades to integer
.../p54common.c:781:32: warning: restricted __le16 degrades to integer
.../p54common.c:1250:28: warning: incorrect type in argument 2 (different base types)
.../p54common.c:1250:28: expected unsigned short [unsigned] [usertype] filter_type
.../p54common.c:1250:28: got restricted __le16 [usertype] filter_type
.../p54common.c:1252:28: warning: incorrect type in argument 2 (different base types)
.../p54common.c:1252:28: expected unsigned short [unsigned] [usertype] filter_type
.../p54common.c:1252:28: got restricted __le16 [usertype] filter_type
.../p54common.c:1257:42: warning: incorrect type in argument 2 (different base types)
.../p54common.c:1257:42: expected unsigned short [unsigned] [usertype] filter_type
.../p54common.c:1257:42: got restricted __le16
.../p54common.c:1260:42: warning: incorrect type in argument 2 (different base types)
.../p54common.c:1260:42: expected unsigned short [unsigned] [usertype] filter_type
.../p54common.c:1260:42: got restricted __le16
.../p54usb.c:228:10: warning: restricted __le32 degrades to integer
.../p54usb.c:228:23: warning: restricted __le32 degrades to integer
.../p54usb.c:228:7: warning: incorrect type in assignment (different base types)
.../p54usb.c:228:7: expected restricted __le32 [assigned] [usertype] chk
.../p54usb.c:228:7: got unsigned int
.../p54usb.c:221:8: warning: symbol 'p54u_lm87_chksum' was not declared.
Should it be static?
All of the above have been fixed. One question, however, remains: In struct
bootrec, the array "data" is treated in many places as native CPU order, but
it may be little-endian everywhere. As far as I can tell, this driver has only
been used with little-endian hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An additional BCM4306 has been found with the Bluetooth coexistence
SPROM coding error.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the e1000/e1000e split, no hardware supported by e1000
supports packet split, just remove the Kconfig option and associated
code from the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following sparse warnings are being generated
because bonding.h is missing definitons for items
declared in bond_main.c but also used in bond_sysfs.h
Also export bond_dev_list as this is also declared
in bond_main but used elsewhere in drivers/net/bonding.
bond_main.c:105:20: warning: symbol 'bonding_defaults' was not declared. Should it be static?
bond_main.c:148:1: warning: symbol 'bond_dev_list' was not declared. Should it be static?
bond_main.c:162:22: warning: symbol 'bond_lacp_tbl' was not declared. Should it be static?
bond_main.c:168:22: warning: symbol 'bond_mode_tbl' was not declared. Should it be static?
bond_main.c:179:22: warning: symbol 'xmit_hashtype_tbl' was not declared. Should it be static?
bond_main.c:186:22: warning: symbol 'arp_validate_tbl' was not declared. Should it be static?
bond_main.c:194:22: warning: symbol 'fail_over_mac_tbl' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Netpoll will call the interrupt handler with interrupts
disabled when using kgdboe, so spin_lock_irqsave() should
be used instead of spin_lock_irq() to prevent interrupts
from being incorrectly enabled.
Signed-off-by: Weiwei Wang <weiwei.wang@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove
the dead code associated with !CONFIG_PPC_MERGE.
With this change the pre_request_irq() and post_free_irq() calls became
nops so they have been removed. Also removed fs_request_irq() and
fs_free_irq() and just called request_irq() and free_irq().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms so we don't need to depend on it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch will add the phy reset bit into the power up mask which is
used during power up. Certain BIOSes will place the phy in reset and
therefore the driver must take the phy out of reset when it loads.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With 2.6.27-rc3 I noticed the following messages in my boot log:
0000:01:00.0: 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09
The second seems correct, but the first has a silly repetition of the
PCI device before the actual message. The message originates from
e1000_eeprom_checks in e1000e/netdev.c.
With this patch below the first message becomes
e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
which makes it similar to directly preceding messages.
Use dev_warn instead of e_warn in e1000_eeprom_checks() as the interface
name has not yet been assigned at that point.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unneeded (struct atl1e_adapter *) casts, for hw->adapter
already has type atl1e_adapter *.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Recent changes to MII bus initialization code added exit points which
didn't free or iounmap the bus before returning.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11372.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reported-by: Daniel Marjamki <danielm77@spray.se>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
