This patch changes the way usbhid carries out Clear-Halt and reset.
Currently, after a Clear-Halt on the interrupt-IN endpoint, the driver
immediately restarts the interrupt URB, even if the Clear-Halt failed.
This doesn't work out well when the reason for the failure was that
the device was disconnected (when a low- or full-speed device is
connected through a hub to an EHCI controller, transfer errors caused
by disconnection are reported as stalls by the hub). Instead now the
driver will attempt a reset after a failed Clear-Halt.
The way resets are carried out is also changed. Now the driver will
call usb_queue_reset_device() instead of calling usb_reset_device()
directly. This avoids a deadlock that would arise when a device is
unplugged: The hid_reset() routine runs as a workqueue item, a reset
attempt after the device has been unplugged will fail, failure will
cause usbhid to be unbound, and the disconnect routine will try to do
cancel_work_sync(). The usb_queue_reset_device() implementation is
carefully written to handle scenarios like this one properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bit 3 in byte 31 of the Sixaxis report indicates whether the battery is
charging or not charging as opposed to whether or not the cable is plugged in.
As a result, when connected via USB and fully charged, the power_supply status
is wrongly reported as 'Discharging' instead of 'Full'.
Use the battery level value to set the cable state so that the power status
is reported correctly as that seems to be the only reliable way to determine the
cable status on the Sixaxis.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
picolcd device is not expected to send any report with size larger than
64 bytes.
If this impossible event happens (sic!), print also a report ID to allow
for easier debugging.
Suggested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can do once the test of the validity of the dj_device, which removes
some duplicated code in various functions.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fixes for potential memory corruption problems in magicmouse and
picolcd drivers (the HW would have to be manufactured to be
deliberately evil to trigger those) which were found by Steven
Vittitoe
- fix for false error message appearing in dmesg from logitech-dj
driver, from Benjamin Tissoires
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: picolcd: sanity check report size in raw_event() callback
HID: magicmouse: sanity check report size in raw_event() callback
HID: logitech-dj: prevent false errors to be shown
The report passed to us from transport driver could potentially be
arbitrarily large, therefore we better sanity-check it so that raw_data
that we hold in picolcd_pending structure are always kept within proper
bounds.
Cc: stable@vger.kernel.org
Reported-by: Steven Vittitoe <scvitti@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The report passed to us from transport driver could potentially be
arbitrarily large, therefore we better sanity-check it so that
magicmouse_emit_touch() gets only valid values of raw_id.
Cc: stable@vger.kernel.org
Reported-by: Steven Vittitoe <scvitti@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Atmel 840B digitizer presents a stylus interface which reports twice
the X coordinate and then twice the Y coordinate. In its current
implementation, hid-input assign the first X to X, then the second to Y,
then the first Y to Z, then the second one to RX.
This is wrong, and X should always be mapped to X, no matter what.
A solution consists in forcing X, Y, Z, RX, RY, RZ to be mapped to their
correct user space counter part.
Reported-by: Éric Brunet <Eric.Brunet@lps.ens.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes UHID_START include a "dev_flags" field that describes details
of the hid-device in the kernel. The first flags we introduce describe
whether a given report-type uses numbered reports. This is useful for
transport layers that force report-numbers and therefore might have to
prefix kernel-provided HID-messages with the report-number.
Currently, only HoG needs this and the spec only talks about "global
report numbers". That is, it's a global boolean not a per-type boolean.
However, given the quirks we already have in kernel-space, a per-type
value seems much more appropriate.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We so far lacked support for hid_hw_raw_request(..., HID_REQ_SET_REPORT);
Add support for it and simply forward the request to user-space. Note that
SET_REPORT is synchronous, just like GET_REPORT, even though it does not
provide any data back besides an error code.
If a transport layer does SET_REPORT asynchronously, they can just ACK it
immediately by writing an uhid_set_report_reply to uhid.
This patch re-uses the synchronous uhid-report infrastructure to query
user-space. Note that this means you cannot run SET_REPORT and GET_REPORT
in parallel. However, that has always been a restriction of HID and due to
its blocking nature, this is just fine. Maybe some future transport layer
supports parallel requests (very unlikely), however, until then lets not
over-complicate things and avoid request-lookup-tables.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We use strict prefixed in uhid.c:
uhid_char_*: implement char-dev callbacks
uhid_dev_*: implement uhid device management and runtime
uhid_hid_*: implement hid-dev callbacks
uhid_raw_request is an hid callback, so rename it to uhid_hid_raw_request.
While at it, move it closer to it's extracted helpers and keep the same
order as in "struct hid_driver".
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The old hdev->hid_get_raw_report() was broken by design. It was never
clear what kind of HW request it should trigger. Benjamin fixed that with
the core HID cleanup, though we never really adjusted uhid.
Unfortunately, our old UHID_FEATURE command was modelled around the broken
hid_get_raw_report(). We converted it silently to the new GET_REPORT and
nothing broke. Make this explicit by renaming UHID_FEATURE to
UHID_GET_REPORT and UHID_FEATURE_ANSWER to UHID_GET_REPORT_REPLY.
Note that this is 100% ABI compatible to UHID_FEATURE. This is just a
rename. But we have to keep the old definitions around to not break API.
>From now on, UHID_GET_REPORT must trigger a GET_REPORT request on the
user-space hardware layer. All the ambiguity due to the weird "feature"
name should be gone now.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All accesses to @report_done are protected by qlock (or report-contexts).
No need to use an atomic.
While at it, invert the logic and call it "report_running". This is
similar to the uhid->running field and easier to read.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All accesses to @report_id are protected by @qlock. No need to use an
atomic.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Avoid hard-coding the target buffer sizes and use sizeof() instead. This
also makes us future-proof to buffer-extensions later on.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Avoid keeping uhid->rd_data and uhid->rd_size set in case
uhid_dev_create2() fails. This is non-critical as we never flip
uhid->running and thus never enter uhid_dev_destroy(). However, it's much
nicer for debugging if pointers are only set if they point to valid data.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of hard-coding the uhid_dev_create() function twice, copy any
create_req into a create2_req structure and forward it.
We allocate uhid_create_req on the stack here, but that should be fine.
Unlike uhid_create2_req it is fairly small (<1KB) and it's only used
temporarily to swap entries. uhid_dev_create2() doesn't access it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The report-query is blocking, so when user-space destroys a device we have
to wake up any blocking kernel context that is currently in the report-cb.
We used some broken correlation between @report_done and @running so far.
Replace it by a much more obvious use.
We now wake up the report-cb if either @report_done or @running is set.
wake_up() and wait_event() serve as implicit barriers (as they always do)
so no need to use smp_rmb/wmb directly.
Note that @report_done is never reset by anyone but the report-cb, thus
it cannot flip twice while we wait for it. And whenever we set @running,
we afterwards synchronously remove the HID device. Therefore, we wait for
all report-cbs to finish before we return. This way, @running can never
flip to true while we wait for it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit "HID: logitech: perform bounds checking on device_id early
enough" unfortunately leaks some errors to dmesg which are not real
ones:
- if the report is not a DJ one, then there is not point in checking
the device_id
- the receiver (index 0) can also receive some notifications which
can be safely ignored given the current implementation
Move out the test regarding the report_id and also discards
printing errors when the receiver got notified.
Fixes: ad3e14d7c5
Cc: stable@vger.kernel.org
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input layer fixes from Dmitry Torokhov:
"Second round of updates for the input subsystem. Mostly small fixups
to the code merged in the first round (atmel_mxt_ts, wacom) but also a
smallish patch to xbox driver to support Xbox One controllers and a
patch to better handle Synaptics profile sensors found in Cr-48
Chromebooks that should not affect any other devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: edt-ft5x06 - remove superfluous assignment
Input: xpad - add support for Xbox One controllers
Input: atmel_mxt_ts - fix a few issues reported by Coverity
Input: atmel_mxt_ts - split config update a bit
Input: atmel_mxt_ts - simplify mxt_initialize a bit
Input: joystick - use get_cycles on ARMv8
Input: wacom - fix compiler warning if !CONFIG_PM
Input: cap1106 - allow changing key mapping from userspace
Input: synaptics - use firmware data for Cr-48
Input: synaptics - properly initialize slots for semi-MT
Input: MT - make slot cleanup callable outside mt_sync_frame()
Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AA
If the device data is not accessible for some reason, returning 0 will cause the call to be
continuously called again as none of the string has been 'consumed'.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently rmi_probe will return -EIO if the device doesn't report that it has F11.
This would indicate that something happened and the device is in the bootloader.
We can recover the device using a userspace firmware update tool, but it needs
access to the device through the hidraw device file. If the probe returns -EIO
the hidraw device won't be created. So instead of failing the probe, just print
an error message, but leave the device accessible from userspace.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If CONFIG_PM is not set:
drivers/hid/wacom_sys.c:1436: warning: ‘wacom_reset_resume’ defined but
not used
Protect the unused functions by #ifdef CONFIG_PM to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_kzalloc for all calls to kzalloc and not just the first. Use
devm functions for other allocations as well. The calls to free the
allocated memory in the probe and remove functions are done away with
and a label is removed in the probe function.
The semantic match that finds the inconsistency is as follows:
// <smpl>
@@
@@
*devm_kzalloc(...)
...
*kzalloc(...)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allocate a buffer with kmalloc for receiving the parameters string
descriptor with usb_control_msg, instead of using a buffer on the stack,
as the latter is unsafe. Use an enum for indices into the buffer to
ensure the buffer size if sufficient.
This fixes the static checker error "doing dma on the stack (buf)".
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fail Huion tablet interface enabling and probing, if parameter retrieval
fails. Move the main code path out of the else block accordingly.
This should prevent devices appearing in a half-working state due to
original report descriptor being used, simplifying diagnostics. This
also makes it easier to add cleanup in later commits, as error handling
is simplified.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
Pull HID updates from Jiri Kosina:
"Some highlights:
- hid-sony improvements of Sixaxis device support by Antonio Ospite
- hid-hyperv driven devices can now be used as wakeup source, by
Dexuan Cui
- hid-lenovo driver is now more generic and supports more devices, by
Jamie Lentin
- hid-huion now supports wider range of tablets, by Nikolai
Kondrashov
- other various unsorted fixes and device ID additions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
HID: hyperv: register as a wakeup source
HID: sony: Default initialize all elements of the LED max_brightness array to 1
HID: huion: Fix sparse warnings
HID: usbhid: Use flag HID_DISCONNECTED when a usb device is removed
HID: ignore jabra gn9350e
HID: cp2112: add I2C mode
HID: use multi input quirk for 22b9:2968
HID: rmi: only bind the hid-rmi driver to the mouse interface of composite USB devices
HID: rmi: check that report ids exist in the report_id_hash before accessing their size
HID: lenovo: Add support for Compact (BT|USB) keyboard
HID: lenovo: Don't call function in condition, show error codes
HID: lenovo: Prepare support for adding other devices
HID: lenovo: Rename hid-lenovo-tpkbd to hid-lenovo
HID: huion: Handle tablets with UC-Logic vendor ID
HID: huion: Switch to generating report descriptor
HID: huion: Don't ignore other interfaces
HID: huion: Use "tablet" instead of specific model
HID: add quirk for 0x04d9:0xa096 device
HID: i2c-hid: call the hid driver's suspend and resume callbacks
HID: rmi: change logging level of log messages related to unexpected reports
...
Putting the various MODULE_* makes them appear several times in modinfo
because wacom.h is used both in wacom_sys.c and wacom_wac.h.
Having the macros near the module declaration makes them appear only once.
Add also MODULE_VERSION(DRIVER_VERSION) to export the current version
number.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bluetooth Wacom tablets are now handled by the regular wacom.ko driver.
Remove the now useless hid-wacom driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Every call of wacom_set_report was passing "id" as a separate parameter
and buffer also passed the same information. We can use first u8 of the
buffer instead of "id"
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bluetooth Intuos 4 use 1-bit definition while the USB ones use a 4-bits
definition. This changes the size of the raw image we receive, and thus
the kernel will only accept 1-bit images for Bluetooth and 4-bits for
USB.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A good point of this change is that now, the Intuos4 bluetooth can handle
the different tools (artpen, airbrush, mice), and we get a common interface
between USB and BT for accessing the LEDs/OLEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that wacom is a hid driver, there is no point in having a separate
driver for bluetooth devices. This patch prepares the common paths of
Bluetooth devices in the common wacom driver. It also adds the sysfs file
"speed" used by Bluetooth devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With this patch, we can move the mouse to wake up the VM after the VM executes
"echo freeze > /sys/power/state".
This addresses part of https://bugzilla.redhat.com/show_bug.cgi?id=1086100
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously only the first element of the array was initialized to 1
leading to potential incorrect max brightness values for the LEDs
on the Dualshock 3 and buzzer controllers.
Use a designated initializer to initialize the whole array to the
correct value.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix sparse warnings in hid-huion.c by using correct buffer type for
retrieved string descriptor.
The warnings in question were:
drivers/hid/hid-huion.c:144:44: sparse: cast to restricted __le16
drivers/hid/hid-huion.c:145:44: sparse: cast to restricted __le16
drivers/hid/hid-huion.c:146:51: sparse: cast to restricted __le16
drivers/hid/hid-huion.c:147:30: sparse: cast to restricted __le16
Reported-by: fengguang.wu@intel.com
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ignore Jabra GN9350E HID interface. USB audio is working nicely, but
registering as HID blocks USB mouse buttons. Since special userspace programs
are needed we will avoid attaching usbhid drivers in general.
Signed-off-by: Patrick Plattes <patrick@erdbeere.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
cp2112 supports single I2C read/write transactions. It can't combine I2C
transactions.
Add master_xfer, using similar code flow as for smbus_xfer.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On composite HID devices there may be multiple HID devices on separate interfaces, but hid-rmi
should only bind to the mouse interface. One example is the Dell Venue 11 Pro's keyboard dock
which contains a composite USB device with a HID touchpad and HID keyboard on separate intefaces.
Since the USB Vendor ID is Synaptic's, hid-core is currently trying to bind hid-rmi to all\of
the HID devices. This patch ensures that hid-rmi only binds to the mouse interface.
related bug:
https://bugzilla.kernel.org/show_bug.cgi?id=80091
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is possible that the hid-rmi driver could get loaded onto a device which does not have the
expected report ids. This should not happen because it would indicate that the hid-rmi driver is
not compatible with that device. However, if it does happen it should return an error from probe
instead of dereferencing a null pointer.
related bug:
https://bugzilla.kernel.org/show_bug.cgi?id=80091
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for both ThinkPad Compact Bluetooth Keyboard with
TrackPoint and ThinkPad Compact USB Keyboard with TrackPoint.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ensure all tpkbd specifics are within a postfixed function, the
main functions for the driver should just switch to the appropriate
function depending on product ID. Given this, we can add extra devices
by including extra postfixed functions.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename module and all functions within so we can add support for other
keyboards in the same file. Rename the _tp postfix to _tpkbd, to
signify functions relevant to the TP USB keyboard.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add handling of Huion tablets with UC-Logic vendor ID, but the same
product ID to hid-huion driver. A Huion H580 was seen using it.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to generating tablet pen report descriptor from a template and
parameters retrieved from string descriptor 0x64.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't ignore non pen-reporting interfaces as they may be used by some
models reusing the same product ID.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use word "tablet" in identifiers and comments instead of referring to specific
Huion tablet model name, as the product ID is used by at least several tablet
models.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error
when I plugin it. and I need to wait for 10s for this device to be ready.
By adding this quirks, the usb keyborad is usable right after plugin
Signed-off-by: Wangzhao Cai <microcaicai@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, the i2c-hid driver does not call the suspend, resume, and
reset_resume callbacks in the hid_driver struct when those events occur.
This means that HID drivers for i2c-hid devices will not be able to execute
commands which may be needed during suspend or resume. One example is when a
touchpad using the hid-multitouch driver gets reset by i2c-hid coming out of
resume. Since the reset_resume callback never gets called the device is never
put back into the correct input mode. This patch calls the suspend and resume
callbacks and tries to duplicate the functionality of the usb-hid driver.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Userspace tools may use hidraw to perform operations on the device from userspace while
hid-rmi is bound to the device. This can cause hid-rmi to print error messages when its
->raw_event() callback gets called as the reports pass through the HID stack. In this case
receiving responses which were not initiated by hid-rmi is not actually an error so the resulting
error messages are incorrect and misleading. This patch changes the log messages to debug so
that the messages can be turned on in the event that there is a problem and there is not
a userspace tool running.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are additional queries which are optional and may not be present
depending on the configuration of the firmware. Knowing which queries are
present is needed to properly compute the address of Query 12 and all
subsequent queries. Additional bits in Query 1 are used to indicate the
presence of these optional queries.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is used by HID Bluetooth devices but also add some more information
to the USB Wireless Receiver.
We are just porting the bits from hid-wacom.c to the common driver here.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current implementation uses "wacom_battery" as a generic name for
batteries. This prevents us to have two Wacom devices with a battery
attached as the power system will complain about the name which is already
registered.
Use an incremental name for each battery attached.
Related bug:
https://sourceforge.net/p/linuxwacom/bugs/248/
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Reports the current status of the battery (discharging, charging, full).
- Also notify the upower daemon when there is a change in the battery
value.
- keep the battery value as a percentage, not the raw value
- add WACOM_QUIRK_BATTERY to easily add a battery to a device (required
for Bluetooth devices)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This solves a bug with the wireless receiver:
- at plug, the wireless receiver does not know which Wacom device it is
connected to, so it does not actually creates all the LEDs
- when the tablet connects, wacom->wacom_wac.features.type is set to the
proper device so that wacom_wac can understand the packets
- when the receiver is unplugged, it detects that a LED should have been
created (based on wacom->wacom_wac.features.type) and tries to remove
it: crash when removing the sysfs group.
Side effect, we can now safely call several times wacom_destroy_leds().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom.ko is now a full HID driver, we have to move it into the proper
subdirectory: drivers/hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All USB Wacom tablets are actually HID devices.
For historical reasons, they are handled as plain USB devices.
The current code makes more and more reference to the HID subsystem
like implementing its own HID report descriptor parser to handle new
devices.
From the user point of view, we can transparently switch from this state
to a driver handled in the HID subsystem and clean up a lot of USB specific
code in the wacom.ko driver.
The other benefit once the USB dependecies have been removed is that we can
use a tool like uhid to make regression tests and allow further cleanup or
new implementations without risking breaking current behaviors.
To match the current handling of devices in wacom_wac.c, we rely on the
hid_type set by usbhid. usbhid sets the hid_type to HID_TYPE_USBMOUSE when
it sees a USB boot mouse protocol declared and HID_TYPE_USBNONE when the
device is plain HID. There is thus a one to one matching between the list
of supported devices before and after the switch from USB to HID.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull HID fixes from Jiri Kosina:
"A few tiny HID subsystem fixes for 3.16"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: use multi input quirk for 22b9:2968
HID: sensor-hub: fix potential memory leak
HID: usbhid: quirk for PM1610 and PM1640 Touchscreen.
HID: rmi: Protect PM-only functions by #ifdef CONFIG_PM
HID: sensor-hub: introduce Kconfig dependency on IOMEM
HID: sensor-hub: make dyn_callback_lock IRQ-safe
CP2112 does not offer an atomic method to set both gpio
direction and value.
Also it does not permit to set gpio value before putting
gpio in output. In fact, accordingly to Silicon Labs
AN495, Rev. 0.2, cpt. 4.4, the HID report to set gpio
values "does not affect any pins that are not configured
as outputs".
This is confirmed on evaluation board CP2112-EK.
With current driver, after execute:
echo in > /sys/class/gpio/gpio248/direction
echo low > /sys/class/gpio/gpio248/direction
gpio output is still high. Only after a following
echo low > /sys/class/gpio/gpio248/direction
gpio output gets low.
Fix driver by changing order of operations; first set
direction then set value.
The drawback of this new sequence is that we can have
a pulse on gpio pin when direction is changed from
input to output-low, but this cannot be avoided on
current CP2112.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move led_mode attribute from HID device to led-class devices and
rename it mode. This will also fix race condition by using
attribute-groups.
(cooloney@gmai.com: fix a typo in commit message)
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This will fix race condition noticed by Oliver Neukum. Sysfs files are
created before mutex and work are initialized.
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This driver adds support for USB controlled led panels that exists in
MSI GT683R laptop
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
hsdev is not freed in sensor_hub_probe when kasprintf inside the for
loop fails. This is because hsdev is not set to platform_data yet (to
be freed by the code in the err_no_mem label). So free the memory
explicitly in the 'if' branch, as this is the only place where this is
(and will) be needed.
Reported-by: coverity
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix checkpatch warning:
WARNING: debugfs_remove(NULL) is safe this check is probably not required
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These device needs to be added to the quirks list with HID_QUIRK_NOGET,
otherwise they will reset upon receiving the get input report requests.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch removes the cast on data of type void* as it is not needed.
The following Coccinelle semantic patch was used for making the change:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T *)x)->f
|
- (T *)
e
)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove an old redundant comment before sony_report_fixup(), it must have
been a leftover from the first version of the driver:
sony_report_fixup() now handles all the supported devices, not only the
Sony Vaio VGX.
The comment is also redundant as the same information provided by it is
also present in the body of the function.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reformat sixaxis_rdesc to reflect its HID structure, and comment each
field. This will make it easier to validate changes to the descriptor in
the future.
No functional changes are introduced, the descriptor is exactly the same
as before byte by byte.
The heavy lifting has been done with the help of hidrd-convert:
https://github.com/DIGImend/hidrd
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplify the logic of overriding the Sixaxis HID descriptor, this will
make it easier to amend the descriptor in future commits.
The current code does this:
if (original sixaxis via USB or BT)
fixup only a part of the descriptor
else if (sixaxis compatible controller)
override the _whole_ descriptor
but the end result is exactly the same, except for the trailing zero in
the case of original BT controllers.
So let's just regularize the process, and always override the HID
descriptor.
Always overriding the descriptor changes the current semantic a little
bit, before this change the BT descriptor still had the trailing zero
byte, while now it is exactly the same as the descriptor of the
controller via USB, but that does not affect proper operation of the
device.
Note that overriding the whole descriptor for original devices is not
strictly necessary for now, but it simplifies the code and in the future
the report descriptor will be patched further and keys will be remapped,
so it's handy to have only one place to patch.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of checking for SIXAXIS_CONTROLLER_USB and SIXAXIS_CONTROLLER_BT
separately, a check on SIXAXIS_CONTROLLER can be used when setting
connect_mask.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If CONFIG_PM=n:
drivers/hid/hid-rmi.c:432: warning: ‘rmi_post_reset’ defined but not used
drivers/hid/hid-rmi.c:437: warning: ‘rmi_post_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
re-add the perm check (we unified the module param and sysfs checks, but
the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args().
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxSN
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
When NO_IOMEM is enabled (e.g. score architecture), some drivers which
need HAS_IOMEM need notice about it, or it will report related warning:
warning: (GPIO_SCH && GPIO_ICH && GPIO_VX855 && GPIO_RDC321X && IE6XX_WDT && RADIO_WL1273 && HID_SENSOR_HUB && MFD_NVEC) selects MFD_CORE which has unmet direct dependencies (HAS_IOMEM)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a UTF-8 non-breaking space character (0xc2 0xa0) after the "Y"
in "Say Y here". This is probably not intentional. Replace it with a
standard ASCII space (0x20).
If you can't see a difference here, I don't blame you :)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The quirks_param array is located in the BSS, no need to explicitly
initialize it with NULL.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
dyn_callback_lock is being taken from IRQ context through hid_irq_in() ->
hid_input_report() -> sensor_hub_raw_event() -> sensor_hub_get_callback(),
therefore anyone else acquiring it needs to disable IRQs to disable deadlocks.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Reported-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Feb 17, 2014, two new usages are approved to HID usage Table 18 -
Digitizer Page:
5A Secondary Barrel Switch MC 16.4
5B Transducer Serial Number SV 16.3.1
This patch adds relevant definitions to hid/input. It also removes
outdated comments in hid.h.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added STM sensor hub new device id. Also added this new device
in HID_SENSOR_HUB_ENUM_QUIRK to fix report descriptors.
These devices uses old FW which uses logical 0 as minimum.
In these, HID reports are not using proper collection classes.
So we need to fix report descriptors,for such devices. This
will not have any impact, if the FW uses logical 1 as minimum.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID
1a2c:0023 does not seem to be handling the reports initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel
when connected, and a delay before its initialization. This patch adds the
quirk for this device, which causes the delay to disappear.
[jkosina@suse.cz: remove superfluous comment and fix ordering]
Signed-off-by: Daniel Kamil Kozar <dkk089@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the Microsoft Surface Pro 2 Type/Touch and default device hardware ID's
Set report quirk for the device in hid-sensor-hub
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, hid-rmi drives every Synaptics product, but the touchscreens
on the Windows tablets should be handled through hid-multitouch.
Instead of providing a long list of PIDs, rely on the scan_report
capability to detect which should go to hid-multitouch, and which
should not go to hid-rmi.
related bug:
https://bugzilla.kernel.org/show_bug.cgi?id=74241https://bugzilla.redhat.com/show_bug.cgi?id=1089583
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some saitek mice implement a tristate button (for switching button mappings in
the original driver) by keeping one of three (non-physical)
buttons constantly pressed.
This breaks X and probably other userspace software.
This patch implements a quirk for the R.A.T.7 and M.M.O.7, tracking the mode
and generating presses of a single button if it changes. Also the missing
release event is generated instantly.
Signed-off-by: Harald Brinkmann <hbrinkmann@braincalibration.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers use the first HID report in the list instead of using an
index. In these cases, validation uses ID 0, which was supposed to mean
"first known report". This fixes the problem, which was causing at least
the lgff family of devices to stop working since hid_validate_values
was being called with ID 0, but the devices used single numbered IDs
for their reports:
0x05, 0x01, /* Usage Page (Desktop), */
0x09, 0x05, /* Usage (Gamepad), */
0xA1, 0x01, /* Collection (Application), */
0xA1, 0x02, /* Collection (Logical), */
0x85, 0x01, /* Report ID (1), */
...
Cc: stable@vger.kernel.org
Reported-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The F11 data in the HID report contains four bits of data for w_x and the least significant bits
of x. Currently only the first three bits are being used which is resulting in small jumps in
the position data on the x axis and in the w_x data.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In line with practice for module parameters, we're adding a build-time
check that sysfs files aren't world-writable.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
In line with practice for module parameters, we're adding a build-time
check that sysfs files aren't world-writable.
Cc: Simon Wood <simon@mungewell.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
x_size_mm should be y_size_mm, otherwise neither the duplicated
condition nor the assignment make any sense whatsoever.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A firmware bug is present on the XPS Haswell edition which silently
split the request in two responses when the caller ask for a read of
more than 16 bytes.
The FW sends the first 16 then the 4 next, but it says that it answered
the 20 bytes in the first report.
This occurs only on the retrieving of the min/max of X and Y of the F11
function.
We only use the first 10 bytes of the Ctrl register, so we can get only
those 10 bytes to prevent the bug from happening.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1090161
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The rmi4 spec defines some optional query registers in F11 which appear before
query 12. This patch checks for the existence of some of the lesser used queries to
compute the location of query12 and all subsequent query registers.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading the partial HID Descriptor is causing a firmware lockup in some
sensor hubs. Instead of a partial read, this patch implements the
i2c hid fetch using a fixed descriptor size (30 bytes) followed by a
verification of the BCDVersion (V01.00), and value stored in
wHIDDescLength (30 Bytes) for V1.00 descriptors.
As per i2c hid spec, this is the preferred model.
From hid-over-i2c-protocol-spec-v1-0:
There are a variety of ways a HOST may choose to retrieve
the HID Descriptor from the DEVICE. The following is a preferred
implementation but should not be considered the only implementation.
A HOST may read the entire HID Descriptor in a single read by
issuing a read for 30 Bytes to get the entire HID Descriptor
from the DEVICE.However, the HOST is responsible for validating that
1. The BCDVersion is V01.00 (later revisions may have different
descriptor lengths), and
2. The value stored in wHIDDescLength is 30 (Bytes) for V1.00
descriptors.
Reported-by: Joe Tijerina <joe.tijerina@st.com>
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix a small bug in computation of report size, which might cause some
devices (Atmel touchpad found on the Samsung Ativ 9) to reject
reports with otherwise valid contents
- a few device-ID specific quirks/additions piggy-backing on top of it
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: sensor-hub: Add in quirk for sensor hub in Lenovo Ideapad Yogas
HID: add NO_INIT_REPORTS quirk for Synaptics Touch Pad V 103S
HID: core: fix computation of the report size
HID: multitouch: add support of EliteGroup 05D8 panels
The sensor hub in Lenovo Yogas needs the enumeration quirk. I've been running
the patch for over a month with no problems, whereas the unpatched drivers
reliably mis-initialized the sensors.
Signed-off-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vincent Fortier <th0ma7@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The extra seven bits are only required when allocating the report buffer.
We can not use those extra bytes for the length of the report in the
generic implementation of .request because the device might (will) refuse
the set_report command.
This has been verified on the Atmel touchpad found on the Samsung Ativ 9
plus, which uses hid-multitouch and HID over I2C. Without this fix, the
device refuses to switch to the multitouch mode, and it becomes unresponsive
from the user point of view.
Actually, this has been discussed during the initial submission of the
commit 4fa5a7f76c, see
https://patchwork.kernel.org/patch/3621751/
Unfortunately, I completely forgot about it later.
Reported-by: Matthias Bayer <thematthiasbayer@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without this patch the 3rd party INTEC (PS3) controller will blink all
leds when user turns them off, it appears to require an extra flag set.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for setting the blink rate of the LEDs. The Sixaxis allows control
over each individual LED, but the Dualshock 4 only has one global control for
controlling the hardware blink rate so individual colors will fall back to
software timers.
Setting the brightness cancels the blinking as per the LED class specifications.
The Sixaxis and Dualshock 4 controllers accept delays in decisecond increments
from 0 to 255 (2550 milliseconds).
The value at index 1 of the DualShock 4 USB output report must be 0xFF or the
light bar won't blink.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add an IDA id allocator to assign unique, sequential device ids to Sixaxis and
DualShock 4 controllers.
Use the device ID to initialize the Sixaxis and DualShock 4 controller LEDs to
default values. The number or color of the controller is set relative to other
connected Sony controllers.
Set the LED class brightness values to the initial values and add the new led to
the array before calling led_classdev_register so that the correct brightness
value shows up in the LED sysfs entry.
Use explicit module init and exit functions since the IDA allocator must be
manually destroyed when the module is unloaded.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the controller Bluetooth MAC address as the unique identifier in the
battery name string instead of the atomic integer that was used before.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert all of the local initialization and shutdown functions to take a
parameter type of struct sony_sc* instead of using a mix of struct sony_sc* and
struct hid_device*.
Allows for the removal of some calls to hid_get_drvdata().
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use a struct for the Sixaxis output report that uses named members to set the
report fields.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use inliners to make sure that the work queue initialization flag is always
checked and set correctly when initializing or cancelling the work queue.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
They need to have the class SERIAL.
Note: it is a Win 7 panel, not Win 8 certified.
Signed-off-by: Tomas Sokorai <tsokorai@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for merge window mismerge in hid-sony, from Frank Praznik
- fix for Surface Type/Touch Cover 2 device, from Benjamin Tissoires
- quirk for ThinkPad Helix sensor hub from Stephen Chandler Paul
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: do not scan constant input report
Revert "HID: microsoft: Add ID's for Surface Type/Touch Cover 2"
HID: sensor-hub: add sensor hub quirk for ThinkPad Helix
HID: sony: Fix cancel_work_sync mismerge
The blink(1) mk2 is a new version of the blink(1) USB RGB LED. The new
generation has 2 individually-controllable RGB chips.
This patch adds support for this device to the thingm driver, which
registers 3 new standard LED class instances for the second RGB chip.
Note that the 'n' (set) command does not support setting a color for a
single RGB chip, so it was changed to 'c' (fade) with a timeout of 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch refactors the way the thingm driver registers a blink(1) LED.
In order to make the driver simpler and more standard, drop the "rgb"
sysfs attribute and create one instance of LED class per RGB channel.
Actually, the name of the LED class instance registered for a blink(1)
device is "blink1::ABCD", where ABCD is the last 4 chars of the serial
number. The driver now registers 3 instances per RGB chip, named
"thingmX:{red,green,blue}:ledY" where X is the hidraw minor number and Y
is the RGB chip number (as seen by the firmware).
This patch also uses work queues to defer calls with the device, which
now allows triggers to work as expected with this LED device.
Also remove the brightness structure field and the brightness_get
backend, as it is already handled by the LED class, and changes the
prefix of functions and structures to thingm_ to match the driver name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As for the "play" sysfs attribute, remove this other non-standard
attribute, so the driver only implements what is required to switch the
LED on and off. Thus, a fade time won't be ideal for some fast-changing
triggers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When the thingm driver registers an instance of LED class, it creates a
"play" sysfs attribute for this blink(1) specific feature.
Since this feature is not specific to the RGB chip but to the HID device
itself, let's remove this attribute from the LED instance and only
implement what is useful to switch on and off the LED.
This feature is still easily accessible through hidraw.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Well, this is embarrassing, if the device is stopped at the end of probe,
we get into big trouble.
This was a leftover of an attempt to be smart when sending the patch,
I deeply apologies.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver add support for RMI4 over USB or I2C.
The current state is that it uses its own RMI4 implementation, but once
RMI4 is merged upstream, the driver will be a transport driver for the
RMI4 library.
Part of this driver should be considered as temporary. Most of the RMI4
processing and input handling will be deleted at some point.
I based my work on Andrew's regarding its port of RMI4 over HID (see
https://github.com/mightybigcar/synaptics-rmi4/tree/rmihid )
This repo presents how the driver may looks like at the end:
https://github.com/mightybigcar/synaptics-rmi4/blob/rmihid/drivers/input/rmi4/rmi_hid.c
Without this temporary solution, the workaround we gave to users
is to disable i2c-hid, which leads to disabling the touchscreen on the
XPS 11 and 12 (Haswell generation).
Related bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=1048314https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1218973
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microsoft Surface Type/Touch Cover 2 is a fancy device which advertised
itself as a multitouch device but with constant input reports.
This way, hid_scan_report() gives the group MULTITOUCH to it, but
hid-multitouch can not handle it due to the constant collection ignored
by hid-input.
To prevent such crap in the future, and while we do not fix this particular
device, make the scan_report coherent with hid-input.c, and ignore constant
input reports.
CC: stable@vger.kernel.org # 3.12+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 117309c51d.
The MS Surface Pro 2 has an USB composite device with 3 interfaces
- interface 0 - sensor hub
- interface 1 - wacom digitizer
- interface 2 - the keyboard cover, if one is attached
This USB composite device changes it product id dependent on if and which
keyboard cover is attached. Adding the covers to hid_have_special_driver
prevents loading the right hid drivers for the other two interfaces, all 3
get loaded with hid-microsoft. We don't even need hid-microsoft for the
keyboards. We have to revert this to load the right hid modules for each
interface.
CC: stable@vger.kernel.org # kernel 3.14 only
Signed-off-by: Derya <derya.kiran@yahoo.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Just like some of the other laptops/tablets on the market with ultrabook
sensors, the ThinkPad Helix's sensor hub requires a special quirk in
order for it to power on properly. Without it the sensors are detected
by the kernel and set up as usual, but they won't output any data. This
will also fix the sensors on any other laptops with the same model of
sensor hub.
Signed-off-by: Stephen Chandler Paul <thatslyude@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- substantial cleanup of the generic and transport layers, in the
direction of an ultimate goal of making struct hid_device completely
transport independent, by Benjamin Tissoires
- cp2112 driver from David Barksdale
- a lot of fixes and new hardware support (Dualshock 4) to hid-sony
driver, by Frank Praznik
- support for Win 8.1 multitouch protocol by Andrew Duggan
- other smaller fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (75 commits)
HID: sony: fix force feedback mismerge
HID: sony: Set the quriks flag for Bluetooth controllers
HID: sony: Fix Sixaxis cable state detection
HID: uhid: Add UHID_CREATE2 + UHID_INPUT2
HID: hyperv: fix _raw_request() prototype
HID: hyperv: Implement a stub raw_request() entry point
HID: hid-sensor-hub: fix sleeping function called from invalid context
HID: multitouch: add support for Win 8.1 multitouch touchpads
HID: remove hid_output_raw_report transport implementations
HID: sony: do not rely on hid_output_raw_report
HID: cp2112: remove the last hid_output_raw_report() call
HID: cp2112: remove various hid_out_raw_report calls
HID: multitouch: add support of other generic collections in hid-mt
HID: multitouch: remove pen special handling
HID: multitouch: remove registered devices with default behavior
HID: hidp: Add a comment that some devices depend on the current behavior of uniq
HID: sony: Prevent duplicate controller connections.
HID: sony: Perform a boundry check on the sixaxis battery level index.
HID: sony: Fix work queue issues
HID: sony: Fix multi-line comment styling
...
Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7AbcACgkQMUfUDdst+ymbZACgncdbZyPsVZ7ZUpBFNbO/vBVT
T9UAmwciojEzjh7b+x4ylsWH+O3LWVN3
=RpAF
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
Fix unfortunate mismerge between the fixes and sony branch causing
code duplication and unterminated basic block.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Sixaxis and DualShock 4 want HID output reports sent on the control
endpoint when connected via Bluetooth. Set the
HID_QUIRK_NO_OUTPUT_REPORTS_ON_INTR_EP flag for these devices so hidraw write()
works properly.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Byte 31 of the Sixaxis report can change depending on whether or not the
controller is rumbling. Using bit 3 is the only reliable way to detect the
state of the cable regardless of rumble activity.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
UHID_CREATE2:
HID report descriptor data (rd_data) is an array in struct uhid_create2_req,
instead of a pointer. Enables use from languages that don't support pointers,
e.g. Python.
UHID_INPUT2:
Data array is the last field of struct uhid_input2_req. Enables userspace to
write only the required bytes to kernel (ev.type + ev.u.input2.size + the part
of the data array that matters), instead of the entire struct uhid_input2_req.
Note:
UHID_CREATE2 increases the total size of struct uhid_event slightly, thus
increasing the size of messages that are queued for userspace. However, this
won't affect the userspace processing of these events.
[Jiri Kosina <jkosina@suse.cz>: adjust to hid_get_raw_report() and
hid_output_raw_report() API changes]
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A few more updates from last week - use of the tdm_slot mapping from
Xiubo plus a few smaller fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2++i
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Final updates for v3.15 merge window
A few more updates from last week - use of the tdm_slot mapping from
Xiubo plus a few smaller fixes and cleanups.
The 3rd argument is pointer to the buffer, not a single __u8.
This has no bad sideeffect, as the stub is not using any of its
argument, but better have it correct.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 3c86726cfe ("HID: make .raw_request mandatory") made .raw_request
mandatory and broke the Hyper-V mouse driver. This patch fixes the problem.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix issue with the sleeping calling hid_hw_request under spinlock.
When i2c is used as HID transport, this is calling kmalloc, which
can sleep. So remove call to this function while under spinlock.
[ 1067.021961] Call Trace:
[ 1067.021970] [<ffffffff8192f5f2>] dump_stack+0x4d/0x6f
[ 1067.021976] [<ffffffff811109f2>] __might_sleep+0xd2/0xf0
[ 1067.021981] [<ffffffff811ea15b>] __kmalloc+0xeb/0x200
[ 1067.021989] [<ffffffff816e0cb3>] ? hid_alloc_report_buf+0x23/0x30
[ 1067.021993] [<ffffffff816e0cb3>] hid_alloc_report_buf+0x23/0x30
[ 1067.021997] [<ffffffff816f4cb7>] i2c_hid_request+0x57/0x110
[ 1067.022006] [<ffffffffa02bc61c>] sensor_hub_input_attr_get_raw_value+0xbc/0x100 [hid_sensor_hub]
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Multitouch touchpads built for Win 8.1 need to be sent an input mode feature report
in order to start reporting multitouch events. This is the same process sent
to Win 7 multitouch touchscreens except the value of the feature report is 3 for
touchpads.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for ordering of device removal actions in hidraw, by Fernando
Luis Vázquez Cao
- fix for uninitialized workqueue usage in hid-sony, by Frank Praznik
- device ID addition for new variant of Logitech G27, from Simon Wood
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-lg4ff: Support new version of G27
HID: hidraw: fix warning destroying hidraw device files after parent
HID: sony: Fix work queue issues.
It has been reported that there is a new hardware version of the G27
in the 'wild'. This patch add's this new revision so that it can be
sent the command to switch to native mode.
Reported-by: "Ivan Baldo" <ibaldo@adinet.com.uy>
Tested-by: "evilcow" <evilcow93@yahoo.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nobody calls hid_output_raw_report anymore, and nobody should.
We can now remove the various implementation in the different
transport drivers and the declarations.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_out_raw_report is going to be obsoleted as it is not part of the
unified HID low level transport documentation
(Documentation/hid/hid-transport.txt)
To do so, we need to introduce two new quirks:
* HID_QUIRK_NO_OUTPUT_REPORTS_ON_INTR_EP: this quirks prevents the
transport driver to use the interrupt channel to send output report
(and thus force to use HID_REQ_SET_REPORT command)
* HID_QUIRK_SKIP_OUTPUT_REPORT_ID: this one forces usbhid to not
include the report ID in the buffer it sends to the device through
HID_REQ_SET_REPORT in case of an output report
This also fixes a regression introduced in commit 3a75b24949
(HID: hidraw: replace hid_output_raw_report() calls by appropriates ones).
The hidraw API was not able to communicate with the PS3 SixAxis
controllers in USB mode.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
tests have shown that output reports use hid_hw_output_report().
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_out_raw_report is going to be obsoleted as it is not part of the
unified HID low level transport documentation
(Documentation/hid/hid-transport.txt)
hid_output_raw_report(hdev, buf, sizeof(buf), HID_FEATURE_REPORT);
is strictly equivalent to:
hid_hw_raw_request(hdev, buf[0], buf, sizeof(buf),
HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
Then replace buf[0] by the appropriate define.
So use the new api.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C5oo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ANTON Touch Pad is a device which can switch from a multitouch
touchpad to a mouse. It thus presents several generic collections which
are currently ignored by hid-multitouch. Enable them by not ignoring
them in mt_input_mapping.
Adding also a suffix for them depending on their application.
Reported-by: Edel Maks <edelmaks@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pens have a special handling in hid-mt as hybrid pen/touch devices
are quite common now. However, some fancy devices presents also
useful collections like mouse or keyboard.
The special case for the pen may not be a special case, and treat it as
a generic case.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The default multitouch protocol class in use since the kernel v3.9 is
working quite well. Since its inclusion, the only devices we had to tweak
were those who really need quirks (GeneralTouch, FocalTech and Wistron,
the 3 of them are Win 7 certified ones).
The flow of new unhandled devices has stopped, which is great and I think
it's time to reduce the list of registered device.
This commit removes only the registration in the kernel of devices that
use the class MT_CLS_DEFAULT, or that can use it. By that, I mean that I
checked all the recordings I have, and the produced input device and
events are the same before and after applying the patch.
This gives two benefits:
- remove a bunch of lines of codes
- prevent bad handling of existing registered devices which are using a
different protocol while using the same VID/PID (I got the case of a
Quanta 3008 recently).
I also removed the associated classes (MT_CLS*). I kept their #define in
case people use the new_id sysfs node with a non standard class (their
should be really few people now, but we never now). This is why there
are /* reserved .... */.
Last, I add a comment on top of mt_devices[] definition to remember people
(and myself) not to include devices for the beauty of it.
To people still trying to add devices with the default class:
"""
Guys, try out your device under a kernel greater or equal to v3.9. If it
works, you are all set. Adding your VID/PID to the kernel only brings us
overload and you won't get anything from it _because_ even a backport of
this shiny patch will _not_ make the device work under 3.0, 3.2, 3.4 or
even 3.8.
So if it works, it works.
If it does not work, then yes, submit a patch or call for help.
In any cases, if you want me to do regression tests, I'd be happy to
get some traces of your device. But I won't patch the kernel if it works.
"""
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I noticed that after hot unplugging a Logitech unifying receiver
(drivers/hid/hid-logitech-dj.c) the kernel would occasionally spew a
stack trace similar to this:
usb 1-1.1.2: USB disconnect, device number 7
WARNING: CPU: 0 PID: 2865 at fs/sysfs/group.c:216 device_del+0x40/0x1b0()
sysfs group ffffffff8187fa20 not found for kobject 'hidraw0'
[...]
CPU: 0 PID: 2865 Comm: upowerd Tainted: G W 3.14.0-rc4 #7
Hardware name: LENOVO 7783PN4/ , BIOS 9HKT43AUS 07/11/2011
0000000000000009 ffffffff814cd684 ffff880427ccfdf8 ffffffff810616e7
ffff88041ec61800 ffff880427ccfe48 ffff88041e444d80 ffff880426fab8e8
ffff880429359960 ffffffff8106174c ffffffff81714b98 0000000000000028
Call Trace:
[<ffffffff814cd684>] ? dump_stack+0x41/0x51
[<ffffffff810616e7>] ? warn_slowpath_common+0x77/0x90
[<ffffffff8106174c>] ? warn_slowpath_fmt+0x4c/0x50
[<ffffffff81374fd0>] ? device_del+0x40/0x1b0
[<ffffffff8137516f>] ? device_unregister+0x2f/0x50
[<ffffffff813751fa>] ? device_destroy+0x3a/0x40
[<ffffffffa03ca245>] ? drop_ref+0x55/0x120 [hid]
[<ffffffffa03ca3e6>] ? hidraw_release+0x96/0xb0 [hid]
[<ffffffff811929da>] ? __fput+0xca/0x210
[<ffffffff8107fe17>] ? task_work_run+0x97/0xd0
[<ffffffff810139a9>] ? do_notify_resume+0x69/0xa0
[<ffffffff814dbd22>] ? int_signal+0x12/0x17
---[ end trace 63f4a46f6566d737 ]---
During device removal hid_disconnect() is called via hid_hw_stop() to
stop the device and free all its resources, including the sysfs
files. The problem is that if a user space process, such as upowerd,
holds a reference to a hidraw file the corresponding sysfs files will
be kept around (drop_ref() does not call device_destroy() if the open
counter is not 0) and it will be usb_disconnect() who, by calling
device_del() for the USB device, will indirectly remove the sysfs
files of the hidraw device (sysfs_remove_dir() is recursive these
days). Because of this, by the time user space releases the last
reference to the hidraw file and drop_ref() tries to destroy the
device the sysfs files are already gone and the kernel will print
the warning above.
Fix this by calling device_destroy() at USB disconnect time.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: stable@vger.kernel.org # 3.13
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a Sixaxis or Dualshock 4 controller is connected via USB while already
connected via Bluetooth it will cause duplicate devices to be added to the
input device list.
To prevent this a global list of controllers and their MAC addresses is
maintained and new controllers are checked against this list. If a duplicate
is found, the probe function will exit with -EEXIST.
On USB the MAC is retrieved via a feature report. On Bluetooth neither
controller reports the MAC address in a feature report so the MAC is parsed from
the uniq string. As uniq cannot be guaranteed to be a MAC address in every case
(uHID or the behavior of HIDP changing) a parsing failure will not prevent the
connection.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure that an out-of-bounds read doesn't occur in the Sixaxis battery level
lookup table in the event that the controller sends an invalid battery status
value in the report.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only initialize force feedback for devices that actually support it (Sixaxis and
Dualshock 4) to prevent calls to schedule_work() with an uninitialized work
queue.
Move the cancel_work_sync() call out of sony_destroy_ff() since the state worker
is used for the LEDs even when force-feedback is disabled.
Remove the sony_destroy_ff() function since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert multi-line comments to comply with the kernel coding style.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove hid_output_raw_report() call as it is not a ll_driver callbacj,
and switch to the hid_hw_* implementation. USB-HID used to fallback
into SET_REPORT when there were no output interrupt endpoint,
so emulating this if hid_hw_output_report() returns -ENOSYS.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
SET_REPORT and GET_REPORT are mandatory in the HID specification.
Make the corresponding API in hid-core mandatory too, which removes the
need to test against it in some various places.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_output_raw_report() is not a ll_driver callback and should not be used.
To keep the same code path than before, we are forced to play with the
different hid_hw_* calls: if the usb or i2c device does not support
direct output reports, then we will rely on the SET_REPORT HID call.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't initialize force-feedback for devices that don't support it to avoid calls
to schedule_work() with an uninitialized work_struct.
Move the cancel_work_sync() call out of sony_destroy_ff() since the state worker
is used for the LEDs even when force-feedback is disabled.
Remove sony_destroy_ff() to avoid a compiler warning since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a SIXAXIS_CONTROLLER macro to simplify conditionals where the
connection type is irrelevant.
Enable the LED and force feedback controls for Sixaxis controllers connected via
Bluetooth.
Send Sixaxis Bluetooth output reports on the control channel.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
Both cp2112_read_req() and cp2112_write_req() are returning negative
value in cases of error, but cp2112_xfer() is storing the return
value into unsigned size_t-typed 'count'.
Fix this by making 'count' signed type.
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit cafebc0 ("HID: remove hid_get_raw_report in struct hid_device")
obsoletes the use of hdev->hid_get_raw_report(), as calling
hid_hw_raw_request() is functionally equivalent.
Convert cp2112 to use this notation.
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the Silicon Labs CP2112 "Single-Chip HID USB to
SMBus Master Bridge."
This is a HID device driver which registers as an i2c adapter and gpiochip to
expose these functions of the CP2112. The customizable USB descriptor fields
are exposed as sysfs attributes. The SMBus byte-read, byte-data-read/write,
and word-data-read transfer modes have been tested by talking to an i2c
sensor. The GPIO functions and USB descriptor field programming have also
been tested.
Signed-off-by: David Barksdale <dbarksdale@uplogix.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The battery_charging and cable_state flags were backwards on the Sixaxis.
The low bit of report byte 30 is 0 when charging and 1 when not.
Bit 5 of byte 31 is 0 when a USB cable is connected and 1 when not.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need at least HID_MAX_BUFFER_SIZE (4096) bytes as input buffer. HID
core depends on this as it requires every input report to be at least as
big as advertised.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In HID sensor hub, HID physical ids are used to represent different sensors.
For example physical id of 0x73 in usage page = 0x20, represents an
accelerometer. The HID sensor hub driver uses this physical ids to create
platform devices using MFD. There is 1:1 correspondence between an phy id and a
client driver.
But in some cases these physical ids are reused. There is a phy id 0xe1, which
specifies a custom sensor, which can exist multiple times to represent various
custom sensors. In this case there can be multiple instances of client MFD
drivers, processing specific custom sensor. In this case when client driver
looks for report id or a field index, it should still get the report id
specific to its own type. This is also true for reports, they should be
directed towards correct instance. This change introduce a way to parse and
tie physical devices to their correct instance.
Summary of changes:
- To get physical ids, use collections. If a collection of type=physical
exist then use usage id as in the name of platform device name
- As part of the platform data, we assign a hdsev instance, which has
start and end of collection indexes. Using these indexes attributes
can be tied to correct MFD client instances
- When a report is received, call callback with correct hsdev instance.
In this way using its private data stored as part of its registry, it
can distinguish different sensors even when they have same physical and
logical ids.
This patch is co-authored with Archana Patni <archna.patni@intel.com>.
Reported-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In some report descriptors, they leave holes in the selectors. In
this case if we use hardcoded selector values, this will result
in invalid values. For example, if there is selectors defined for
Power State from OFF to D0 to D3. We can't use indexes of these states
if some states are not implemented or not present in the report decriptors.
In this case, we need to get the indexes from report descriptors.
One API is added to get the index of a selector. This API will
search for usage id in the field usage list and return the index.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added STM sensor hub vendor id in HID_SENSOR_HUB_ENUM_QUIRK to
fix report descriptors. These devices uses old FW which uses
logical 0 as minimum. In these, HID reports are not using proper
collection classes. So we need to fix report descriptors,for
such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
We look for usage id for "power and report state", and modify
logical minimum value to 1.
This is a follow-up patch to commit id 875e36f8.
Signed-off-by: Archana Patni <archana.patni@linux.intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is better to check them soon enough before triggering any kernel panic.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For BT transport layer,
ret = hid_output_raw_report(A, B, C, HID_OUTPUT_REPORT);
is equivalent to
ret = hid_hw_output_report(A, B, C);
So use the new API where available
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ret = hid_output_raw_report(A, B, C, HID_FEATURE_REPORT);
is equivalent to
ret = hid_hw_raw_request(A, B[0], B, C, HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
whatever the transport layer is.
So use the new API where available
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-input do not use anymore hid_output_raw_report() to set the LEDs.
Use the correct implementation now and make them working again.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If there is no urbout when sending a output report, ENOSYS (Function
not implemented) is a better error than EIO (I/O error).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Having our own .request() implementation does not give anything,
so use the generic binding.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add output_report and raw_request to i2c-hid.
The current implementation of i2c_hid_output_raw_report decides
by itself if it should use a direct send of the output report
or use the data register (SET_REPORT). Split that by reimplement
the logic in __i2c_hid_output_raw_report() which will be dropped
soon.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
.request() can be emulated through .raw_request()
we can implement this emulation in hid-core, and make .request
not mandatory for transport layer drivers.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>