The Timer Pulse Unit has registers that lie outside the declared
register block. Enlarge the register block size to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6050000.pfc and pfc@e6050000 to
e6050000.pin-controller and pin-controller@e6050000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /cache-controller has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Fixed rate and fixed factor clocks do not require an
clock-output-names property.
* Since 07705583e9 ("clk: shmobile: div6: Make clock-output-names
optional") Renesas div6 clocks do not require a clock-output-names
property.
In the above cases there is only one clock output and its name is taken
from that of the clock node. Accordingly, remove the unnecessary
clock-output-names properties and as necessary update the node names.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in r8a7740 device tree.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a crisp
overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWnr6fAAoJEIwa5zzehBx3p+gP+wYLUqXjCYgyu6oJPxJbWghj
gPc4QJmhVlAWTqvE7Ut7RumWzGa7nUEH2QF9tiCLbDAw8727HJXhRHknFwaCsX45
BsvFQaKY99ClfUhoSI9GRa8e2jEArjzEPqkynHW/8FM20qWaj/Z8DDfixG75gR8u
onrMw6kprNGwmyQwqu5zLDXhUBCQIs1xRRSabUjV1P5420dbBaGgtmQrdj7k+JDt
wo9SKiG6d9CSYil3r7BC+0JwzbKNBxRGs2vv1BJOfbZ3Lj+uC0vj1AxoF/p7dOHy
ohuvt7UwwtoUzzFMcMUo7E8qxl9u6bbnPDlUoRF7DVVi5SQoeZd8BOZXOdLRN2OQ
qtgsmziDxtvh7Ydj6i89D69x7+GurAFcP8Aturprc5Zd5lO70PAYBD379IhIZ8y1
MVJltIEeuUZo7BaVBCHWQY9jJRtI3bAU6JdFPrFROsuo810IYd72Wbb1ZCfF7SV7
nBRvV7e71VQxb48c3p8Et5FntHuXfUlhkMrQ7Cb+2ugB/diGgZB9NfrZbP3Azv7f
A5Ey9tNHaOCUxzYDCw80jTa7OwVWNJf2kOT1yikASk3vODKLv4E5YQ2DULnObWG7
iRmLYuuGka4sMs0ZjpV3kaqs+8rWu08x2rEr5X0wfU+DalIzUWA2oDKSgPLJoacV
gXKP039CIxQAiottcppA
=XDLa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing L2 cache-controller node, and link the CPU node to it.
This will allow migration to the generic l2c OF initialization.
The L2 cache is an ARM L2C-310 (r3p1-150rel0), of size 256 KiB (32 KiB x
8 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If a GPIO driver uses gpiochip_add_pin_range() (which is usually the
case for GPIO/PFC combos), the GPIO hogging mechanism configured from DT
doesn't work:
requesting hog GPIO lcd0 (chip r8a7740_pfc, offset 176) failed
The actual error code is -517 == -EPROBE_DEFER.
The problem is that PFC+GPIO registration is handled in multiple steps:
1. pinctrl_register(),
2. gpiochip_add(),
3. gpiochip_add_pin_range().
Configuration of the hogs is handled in gpiochip_add():
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_hogs
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
pinctrl_request_gpio
pinctrl_get_device_gpio_range
However, at this point the GPIO controller hasn't been added to
pinctrldev_list yet, so the range can't be found, and the operation fails
with -EPROBE_DEFER.
To fix this, add a "gpio-ranges" property to the gpio device node, so
the range is added by of_gpiochip_add_pin_range(), which is called by
of_gpiochip_add() before the call to of_gpiochip_scan_hogs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The single SCIFB on R-Mobile A1 is called "scifb", not "scifb8".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the remaining DIV6 clocks and all possible parents for the SUB
clock.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the DDR3 Bus State Controller (DBSC3).
The DBSC3 is located in the A4S PM domain, which must not be powered
down, else the system will crash.
This has no visible effect for now, as A4S was never turned off anyway
because its child PM domain A3SM contains the CPU core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and hook
it up to the D4 PM domain, so the R-Mobile System Controller driver can
keep the domain powered, until the new Coresight code handles runtime
PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With the addition of clock-indices in commit 8e33f91a0b ("clk:
shmobile: clk-mstp: change to using clock-indices"), we can change the
DTSes to use the generic property instead of the deprecated
vendor-specific property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clocks property for the scifa2 device node referred to the scifa0
clock index instead of the scifa2 clock index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the INTCA irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r8a7740 48-bit CMT
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the CMT1 counters to the r8a7740 device tree and make it
disabled by default.
Based on work by Magnus Damm.
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declares the r8a7740 clocks supported by the legacy clock framework,
excluding those requiring extensions to the DIV6 driver.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This describes all of the SCIF hardware of the r8a7740.
Each node is disabled and may be enabled as necessary
by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As with previous release, this continues to be among the largest branches
we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OvOG
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
r8a7791 (R-Car H2) SoC and its Koelsch board and,
r8a7740 (R-Mobile A1) SoC and its Armadillo800eva board
* Set CPU clock frequency from OF nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pLjF
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-cleanup-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC soc-cleanup Updates for v3.16" from Simon Horman:
r8a7791 (R-Car H2) SoC and its Koelsch board and,
r8a7740 (R-Mobile A1) SoC and its Armadillo800eva board
* Set CPU clock frequency from OF nodes
* tag 'renesas-soc-cleanup-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Set clock frequency in HZ from OF nodes
ARM: shmobile: Use shmobile_init_late() on r8a7740
ARM: shmobile: Remove unused r8a7791_init_early()
ARM: shmobile: Use r8a7791 DT CPU Frequency for Koelsch
ARM: shmobile: Use r8a7791 DT CPU Frequency in common case
ARM: shmobile: Remove unused r8a7740_init_delay()
ARM: shmobile: Use r8a7740 DT CPU Frequency for Armadillo DT Ref
ARM: shmobile: Use r8a7740 DT CPU Frequency in common case
ARM: shmobile: Add r8a7740 Maximum CPU Frequency to DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
There's no need to duplicate the interrupt-parent property in all DT
nodes as the kernel automatically walks parent nodes to find the
property. Specify it once in the root node only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add 800 MHz to the r8a7740 DTS to describe the maximum CPU frequency.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,*-r8a7740" to the compatible strings for consistency with other
devices.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,intc-irqpin-r8a7740" to the compatible string for the
IRQ pins in case of r8a7740 INTC. This makes the INTC irqpin follow
the same style as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
This patch also adds missing SDHI2 entry
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI0 and MMCIF interfaces to armadillo800eva-reference with
regulators and pin configurations. SDHI1 is not added yet, because the
switch, that connects the interface either to an SD slot or to a WiFi
SDIO card cannot be described in DT yet.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently all I2C interfaces in all *.dtsi files for various Renesas SoCs
are enabled by default. Switch them all off and only enable populated I2C
interfaces in board-specific *.dts files.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization
Conflicts: Too many. Most of these are because Simon chose to send
some board updates through the V4L tree that ends up colliding with
the main platform changes. We'll work with him on sorting out his
workflow:
- arch/arm/boot/dts/r8a7740.dtsi:
- Add/add conflict in a devicetree file (keep both)
- arch/arm/mach-shmobile/Makefile:
- Splitting out of clock files collides with intc move to DT.
Keep HEAD version but remove intc-* files for R8A7740 and R8A7779.
- arch/arm/mach-shmobile/board-bockw.c:
- Keep HEAD but remove i2c, hspi and mmc device init calls
- arch/arm/mach-shmobile/board-marzen.c
- Remove mach/hardware.h include and r8a7779_add_usb_phy_device() call,
everything else stays.
- arch/arm/mach-shmobile/include/mach/r8a7778.h:
- From HEAD, Keep camera-rcar.h include and r8a7778_add_vin_device()
- From branch, keep everything
- arch/arm/mach-shmobile/include/mach/r8a7779.h:
- From HEAD, Keep only camera-rcar.h include and r8a7779_add_vin_device()
- arch/arm/mach-shmobile/setup-r8a7778.c
- Keep HEAD, but drop the MMC section (struct resource + add_mmc_device())
- take the new function name from our side (r8a7778_add_dt_devices())
- arch/arm/mach-shmobile/setup-r8a7779.c
- Keep HEAD, but drop r8a7779_add_usb_phy_device()
I've also pushed a test-merge2 branch where you can see how I resolved
them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fagt
-----END PGP SIGNATURE-----
Merge tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Renesas SoC cleanup, refactoring and more SMP support from Kevin Hilman:
"Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization"
* tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
ARM: shmobile: Per-CPU SMP boot / sleep code for SCU SoCs
ARM: shmobile: Introduce per-CPU SMP boot / sleep code
ARM: shmobile: Use shared SCU CPU Hotplug code on r8a7779
ARM: shmobile: Use shared SCU CPU Hotplug code on sh73a0
ARM: shmobile: Add shared SCU CPU Hotplug code
ARM: shmobile: Use shared SCU SMP boot code on emev2
ARM: shmobile: Use shared SCU SMP boot code on r8a7779
ARM: shmobile: Use shared SCU SMP boot code on sh73a0
ARM: shmobile: Introduce shared SCU SMP boot code
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
...
Add PMU information to r8a7740.dtsi. With this
included Armadillo800eva DT reference may use the PMU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>