Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves. This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios(). So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Only one caller to sdhci_set_clock() needs to check whether the
requested clock frequency was the same as the currently set frequency,
yet we work around this in several other sites via sdhci_update_clock().
Rather than doing this, move those checks out into sdhci_do_set_ios(),
which then allows sdhci_update_clock() to be eliminated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than using the streaming API, use the coherent allocator to
provide this memory, thereby eliminating cache flushing of it each
time we map and unmap it. This results in a 7.5% increase in
transfer speed with a UHS-1 card operating in 3.3v mode at a clock
of 49.5MHz.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
On read, we don't need to sync the whole scatterlist and then check
whether any segments need copying - if we check first, we avoid
potentially expensive cache handling.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When we disable card detection interrupts, we should disable both the
insert and remove interrupts irrespective of the current state - this
avoids races between the hardware card detect changing state before
we've read that updated state and altered the interrupt mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Allow SDIO interrupts to be received while the SDHCI host is runtime
suspended. We do this by leaving the AHB clock enabled while the
host is runtime suspended so we can access the SDHCI registers, and
so read and raise the SDIO card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
There's no requirement to have the card tasklet separate now that we
have a threaded interrupt handler, so kill this and move the called
code into the threaded part of the handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use a generic threaded interrupt handler for SDIO interrupt handling,
rather than allowing the SDIO core code to buggily spawn its own
thread. This results in host drivers to be more in control of how
SDIO interrupts are acknowledged in the hardware, rather than having
the internals of the SDIO core placed upon them, possibly resulting
in sub-standard handling.
At least one SDHCI implementation specifies a very specific sequence
to deal with a card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need to change the SDHCI_SDIO_IRQ_ENABLED flag when we're
merely receiving an interrupt - IRQ handling thread in the MMC core
will either re-enable or disable the interrupt via the enable_sdio_irq
callback, which will update this status appropriately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci interrupt handling is a mess; there is a lot of code doing very
similar things. Let's clean this up a bit:
1. set's clear down cmd, data and bus power interrupts in one go - we're
always going to handle these.
2. use a do { } while () loop for looping while there are pending
interrupts.
3. group clearing of bits in intmask into one place.
This results in the code becoming simpler and easier to read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than the SDIO support spawning it's own thread for handling card
interrupts, use the generic IRQ infrastructure for this, triggering it
from the host interface's interrupt handling directly.
This avoids a race between the parent thread waiting to receive an
interrupt response from the card, and the slow startup from the sdio
irq thread, which can occur as a result of high system load (eg, while
udev is running.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Very minor source and binary size reduction.
Signed-off-by: George Spelvin <linux@horizon.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This eliminates a 1-bit left shift in every single caller,
and makes the inner loop of the CRC computation more efficient.
Renamed crc7 to crc7_be (big-endian) since the interface changed.
Also purged #include <linux/crc7.h> from files that don't use it at all.
Signed-off-by: George Spelvin <linux@horizon.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unneccesary 1ms mdelay in the HS200 tuning
loop, called 40 times per retuning. Currently this causes a latency
of >40ms on any emmc accesses triggering wake from runtime PM,
which can occur for a significant portion of reads on a mostly idle system.
The delay is left in place for SD Cards, which use
MMC_SEND_TUNING_BLOCK rather than MMC_SEND_TUNING_BLOCK_HS200.
I'm not able to find evidence that this is required for SD in the
specs I have access to, however this delay has been present from
initial checkin for SD so I have preserved the original behavior for
compatibility.
This has been verified to fix observed glitching on local audio
playback and recording on apps with inbuilt assumptions on storage
latency.
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Callers of mmc_regulator_get_supply could benefit from knowing if either
of the regulators are present but not yet available. Since callers do
not currently examine the return value, modify this function to return
zero or -EPROBE_DEFER if either regulator get returns the same.
Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal
with absent regulators, switch to devm_regulator_get_optional. This has
the added benefit of allowing this function to behave correctly even in
the !CONFIG_REGULATOR case such that the stub can be removed.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch replaces regulator manipulation with
mmc_regulator_get_supply() function from MMC core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Found using smatch:
drivers/mmc/host/atmel-mci.c:827 atmci_pdc_complete() warn: variable
dereferenced before check 'host->data' (see line 807)
Stop testing host->data as it is not NULL at that point.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
rtsx_usb_sdmmc module uses the LED classdev if available, but the code
failed to consider the situation that it is built-in and the LED classdev is a
module, leading to following linking error:
LD init/built-in.o
drivers/built-in.o: In function `rtsx_usb_sdmmc_drv_remove':
rtsx_usb_sdmmc.c:(.text+0x2a018e): undefined reference to
`led_classdev_unregister'
drivers/built-in.o: In function `rtsx_usb_sdmmc_drv_probe':
rtsx_usb_sdmmc.c:(.text+0x2a197e): undefined reference to
`led_classdev_register'
Fix by excluding such condition when defining macro RTSX_USB_USE_LEDS_CLASS.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Return -ENOSYS in get_cd if broken-cd is specified in the device tree.
Commit a91fe279ae (mmc: mxs: use standard flag for broken card
detection) sets MMC_CAP_NEEDS_POLL when broken-cd is specified. This
driver sets this flag unconditionally as it does not support a card
detect interrupt. Instead, broken-cd means that there is no card detect
signal connected.
The mmc core checks the get_cd function return value to determine if a
card is present. Only for a non-zero return value it will attempt to
initialize the card. So retuning -ENOSYS will allow the card to be
initialized.
For comparison, mmc_gpio_get_cd in slot-gpio.c also returns -ENOSYS if
the card detect GPIO is not valid.
Signed-off-by: Daniel Willmann <daniel@totalueberwachung.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
As of commit bcc3e1726d ("mmc: block: Use R1 responses for stop cmds for
read requests"), stop commands for reads do not have MMC_RSP_BUSY set.
In this case we should not wait for a PRG_DONE IRQ after sending the
stop command: it will not get raised when the busy flag is not set,
causing the request to fail with a timeout.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chris Ball <chris@printf.net>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host,
for those host driver's that can't distinguish this in runtime.
Specially, if host can support HS400, it means that host can also
support HS200.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high
speed DDR interface timing from HS200. Clock frequency is up to 200MHz
and only 8-bit bus width is supported. In addition, tuning process of
HS200 is required to synchronize the command response on the CMD line
because CMD input timing for HS400 mode is the same as HS200 mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Jackey Shen <jackey.shen@amd.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.
The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Power class is changed once only after selection of bus modes
including speed and bus-width finishes finally.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Device types which are supported by both host and device can be
identified when EXT_CSD is read. There is no need to check host's
capability anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
SDIO controllers found on Marvell Kirkwood SoCs seem to cause a late,
spurious irq although all interrupts have been disabled. This irq
doesn't do any harm, neither to HW nor driver. To avoid some
"unexpected irq" warning later, we workaround above issue by bailing
out of irq handler early, if we didn't expect any.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
mvsdio reports method of card detection with dev_notice, while for
removable cards it may be sane, for non-removable cards it is not.
Also, as the user cannot do anything about it, silence the message
by reducing it from dev_notice to dev_dbg.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The eMMC signalling voltage is determined by VCCQ which is provided to
the card by the host. Signalling is not required to begin at 3.3v and,
if the host and card both support a particular VCC/VCCQ combination, it
can be used immediately.
In contrast, SD Cards must begin with 3.3v signalling and may switch to
a lower voltage signalling if instructed to do so in CMD11. A message
is required to coordinate this operation because the card only receives
a 3.3v VDD and must know when to use the 1.8v produced by its internal
regulator.
It makes sense for the core to begin with 3.3v signalling but when that
can't be set, 1.8v and 1.2v signalling also should be attempted. This
is especially important when an external regulator with a limited range
is used to supply VCCQ to an eMMC part.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add SD/MMC driver for MOXA ART SoCs.
The "MOXA ART MMC controller" is likely a faraday "ftsdc010",
a controller with support in U-Boot:
http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/mmc/ftsdc010_mci.c
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Realtek USB SD/MMC host driver provides mmc host support based on the
Realtek USB card reader MFD driver.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
NUM_GPIOS is not used after e19499ae10 ("mmc: sdhci-s3c: let device
core setup the default pin configuration"). Thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Restore the card-present checking point.
(The following part was removed from commit bf626e5 ("mmc: dw_mmc:
use slot-gpio to handle cd pin")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
It's right to check immediately whether host->bus_hz is assigned or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
mmc_of_parse() have been already parsed the general capability.
Didn't need to use the local parser.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Remove the option to provide the flags for mmc capabilities as platform
data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the option to provide signal direction configuration and
feeback clock as platform data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is pure software configuration, which mmci has been supporting for
a while. Let's enable it as default so we can take benefit from it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let mmci DT parser only handle the specific bindings related to mmci
and extend the DT support by converting to the common mmc DT parser.
While both DT and platform data exist, DT takes precedence. If there
are supplied DT data, the card detect and write protect GPIOS are
enforced to be provided through it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ST Micro variant supports the option of using a feedback clock signal in
favor of the clockout pin when latching incoming signals on the data bus.
Since this is matter of how pins are being routed we need to provide a new DT
binding to be able to configure this through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Some variants have support for indicating the bus signal directions,
which currently are configured through platform data.
Add corresponding DT bindings to enable us to move away from using the
platform data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
To avoid duplication of code while handling card detect and write
protect GPIO pins/irqs, let's convert to use the mmc gpio API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For CONFIG_PM_SLEEP, the device were always left in full power state
after system suspend.
We solely relied on a power domain to put it into low power state,
which is an unreasonable requirement to put on SOCs to implement.
Especially for those SOCs not supporting power domains at all.
Use pm_runtime_force_suspend|resume() as the system suspend callbacks,
to resolve the issue.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In runtime suspended state, we are not expecting IRQs and thus we can
safely mask them, not only for pwrreg_nopower variants but for all.
Obviously we then also need to make sure we restore the IRQ mask while
becoming runtime resumed.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c42deffd5b.
commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.
The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Realtek USB SD/MMC host driver provides mmc host support based on the Realtek
USB card reader MFD driver.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
a27fbf2f06 ("mmc: add ignorance case for CMD13 CRC error") produced
a cmd.flags unhandled in realtek pci host driver. This will make MMC
card fail to initialize, this patch is used to handle the new cmd.flags
condition and MMC card can be used.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The sdio func device is added to the driver model after the card
device.
This means the sdio func device will be suspend before the card device
and thus resumed after. The consequence are the mmc core don't
explicity need to protect itself from receiving sdio requests in
suspended state. Instead that can be handled from the sdio bus, which
is thus invokes the PM callbacks instead of old dummy function.
In the case were the sdio func driver don't implement the PM callbacks
the mmc core will in the early phase of system suspend, remove the
card from the driver model and thus power off it.
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: xiaoming wang <xiaoming.wang@intel.com>
Tested-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
When plugging a specific micro SD card at MMC socket of a custom i.MX28 board,
we get the following kernel warning:
WARNING: CPU: 0 PID: 30 at drivers/mmc/host/mxs-mmc.c:342 mxs_mmc_start_cmd+0x34c/0x378()
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:1 Not tainted 3.14.0-rc5 #8
Workqueue: kmmcd mmc_rescan
[<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
[<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
[<c001daf8>] (warn_slowpath_common) from [<c001db34>] (warn_slowpath_null+0x1c/0x24)
[<c001db34>] (warn_slowpath_null) from [<c0349478>] (mxs_mmc_start_cmd+0x34c/0x378)
[<c0349478>] (mxs_mmc_start_cmd) from [<c0338fa0>] (mmc_start_request+0xc4/0xf4)
[<c0338fa0>] (mmc_start_request) from [<c03390b4>] (mmc_wait_for_req+0x50/0x164)
[<c03390b4>] (mmc_wait_for_req) from [<c03405b8>] (mmc_app_send_scr+0x158/0x1c8)
[<c03405b8>] (mmc_app_send_scr) from [<c033ee1c>] (mmc_sd_setup_card+0x80/0x3c8)
[<c033ee1c>] (mmc_sd_setup_card) from [<c033f788>] (mmc_sd_init_card+0x124/0x66c)
[<c033f788>] (mmc_sd_init_card) from [<c033fd7c>] (mmc_attach_sd+0xac/0x174)
[<c033fd7c>] (mmc_attach_sd) from [<c033a658>] (mmc_rescan+0x25c/0x2d8)
[<c033a658>] (mmc_rescan) from [<c003597c>] (process_one_work+0x1b4/0x4ec)
[<c003597c>] (process_one_work) from [<c0035de4>] (worker_thread+0x130/0x464)
[<c0035de4>] (worker_thread) from [<c003c824>] (kthread+0xb4/0xd0)
[<c003c824>] (kthread) from [<c000f420>] (ret_from_fork+0x14/0x34)
The error is due to an invalid value in CSD register of a specific 2GB
micro SD card. The CSD version of this card is 1.0 but the TACC field
has the invalid value 0.
cid:0000005553442020000000000000583f
csd:00000032535a83bfedb7ffbf1680003f
date:08/2005
erase_size:512
fwrev:0x0
hwrev:0x0
manfid:0x000000
name:USD
oemid:0x0000
preferred_erase_size:4194304
scr:0225000000000000
serial:0x00000000
type:SD
Since the kernel is making use of this TACC field to calculate the SD
card timeout, an invalid value 0 leads to a warning at
mxs_ns_to_ssp_ticks() and later the following misleading error message
appears in a loop:
mxs-mmc 80010000.ssp: card claims to support voltages below defined range
mxs-mmc 80010000.ssp: no support for card's volts
mmc0: error -22 whilst initialising MMC card
This error is only found on this 2GB SD card on mxs platform.
On x86 this card works without any problems.
The following patch based on the work of Peter Chan and Otavio Salvador.
It catches the case that the determined timeout is still 0 and sets it
to a valid value.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This change removes the callback from atomic context which it doesn't
need to be in, and puts it in line with the debounced rescan.
This code is based on these e-mail threads with Christian Daudt:
https://lkml.org/lkml/2013/8/19/539https://lkml.org/lkml/2014/3/19/79
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Replaced UHS_DDR50 with MMC_DDR52. And MMC_CAP_UHS_DDR50
is removed because of non-implementation of UHS signaling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Added MMC_DDR52 as eMMC's DDR mode is distinguished from SD-UHS.
CC: Wei WANG <wei_wang@realsil.com.cn>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Added MMC_DDR52 as eMMC's DDR mode distinguished from SD-UHS.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
Intel SDIO has broken card detect so add a quirk to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Pull ARM changes from Russell King:
- Perf updates from Will Deacon:
- Support for Qualcomm Krait processors (run perf on your phone!)
- Support for Cortex-A12 (run perf stat on your FPGA!)
- Support for perf_sample_event_took, allowing us to automatically decrease
the sample rate if we can't handle the PMU interrupts quickly enough
(run perf record on your FPGA!).
- Basic uprobes support from David Long:
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
- ARMv7M (microcontroller) updates from Uwe Kleine-König
- OMAP DMA updates (recently added Vinod's Ack even though they've been
sitting in linux-next for a few months) to reduce the reliance of
omap-dma on the code in arch/arm.
- SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan
- Support for Cortex-A12 CPU
- Align support for ARMv6 with ARMv7 so they can cooperate better in a
single zImage.
- Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.
- Removal of IRQ_DISABLED from various ARM files
- Improved efficiency of virt_to_page() for single zImage
- Patch from Ulf Hansson to permit runtime PM callbacks to be available for
AMBA devices for suspend/resume as well.
- Finally kill asm/system.h on ARM.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
dmaengine: omap-dma: more consolidation of CCR register setup
dmaengine: omap-dma: move IRQ handling to omap-dma
dmaengine: omap-dma: move register read/writes into omap-dma.c
ARM: omap: dma: get rid of 'p' allocation and clean up
ARM: omap: move dma channel allocation into plat-omap code
ARM: omap: dma: get rid of errata global
ARM: omap: clean up DMA register accesses
ARM: omap: remove almost-const variables
ARM: omap: remove references to disable_irq_lch
dmaengine: omap-dma: cleanup errata 3.3 handling
dmaengine: omap-dma: provide register read/write functions
dmaengine: omap-dma: use cached CCR value when enabling DMA
dmaengine: omap-dma: move barrier to omap_dma_start_desc()
dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
dmaengine: omap-dma: consolidate clearing channel status register
dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
dmaengine: omap-dma: provide register definitions
dmaengine: omap-dma: consolidate setup of CCR
dmaengine: omap-dma: consolidate setup of CSDP
...
The SDHCI unit used on the Armada 380 and 385 Marvell SoC is similar
to the PXAv3 unit. The only difference is that on Armada 38x, the
PXAv3 unit accesses memory through MBus windows which must be
configured prior to using the device. Without this, DMA would not
work.
In order to achieve this, the sdhci-pxav3 driver is extended with an
additional compatible string "marvell,armada-380-sdhci". When this
compatible string is used, the MBus windows are initialized in a way
that is identical to what all other DMA-capable drivers for Marvell
EBU platforms do.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chris Ball <chris@printf.net>
Tejun Heo has made WQ_NON_REENTRANT useless in the dbf2576e37
("workqueue: make all workqueues non-reentrant"). So remove its
usages and definition.
This patch doesn't introduce any behavior changes.
tj: minor description updates.
Signed-off-by: ZhangZhen <zhenzhang.zhang@huawei.com>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Acked-by: James Chapman <jchapman@katalix.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds implementation for platform specific tuning in order
to support HS200 bus speed mode on Qualcomm SDHCI controller.
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This platform driver adds the initial support of Secure Digital Host
Controller Interface compliant controller found in Qualcomm chipsets.
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When the host->tuning_count is zero it means that the retuning is
disabled. This is checked on the first run of sdhci_execute_tuning()
by the if statement below:
if (!(host->flags & SDHCI_NEEDS_RETUNING) && host->tuning_count &&
(host->tuning_mode == SDHCI_TUNING_MODE_1)) {
So only when tuning_count is non-zero it will set the host flag
SDHCI_USING_RETUNING_TIMER. The else statement is only for re-programming
the timer, which means that flag must be set. Because that is not checked
the else statement is executed in the first run when tuning_count is zero.
This was seen on a host controller which indicated SDHCI_TUNING_MODE_1 (0)
and tuning_count being zero. Suspect that (one of) these registers is not
properly set.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Currently ARCH_BCM has been used for Broadcom Mobile V7 based SoCs.
In order to allow other Broadcom SoCs to also use mach-bcm directory and
files, this patch renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <chris@printf.net>
If the SDHCI irq is shared with another device then the interrupt
handler can get called while SDHCI is runtime suspended. That is
harmless but the warning message is not useful so remove it. Also
returning IRQ_NONE is more appropriate.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Add ACPI HID 80860F16 as a host controller for a SD card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Some 80860F14 devices do not support card detect and must rely
completely on GPIO. Presently the card detect GPIO is used
only to wake-up from runtime suspend. Change to using
mmc_gpioid_request_cd() which will cause the SDHCI driver to
prefer the GPIO to the host controller's native card detect.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Add functions to request a CD GPIO using the GPIO descriptor API.
Note that the new request function is paired with mmc_gpiod_free_cd()
not mmc_gpio_free_cd(). Note also that it must be called prior to
mmc_add_host() otherwise the caller must also call
mmc_gpiod_request_cd_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
In preparation for adding a descriptor-based CD GPIO API, split out
CD IRQ request into a separate function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
In preparation for adding a descriptor-based CD GPIO API, switch from
recording GPIO numbers to recording GPIO descriptors.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci has support for using GPIOs for card detection. If we have a
GPIO specified, we can use that directly, without needing our own
interrupt handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <chris@printf.net>
None of this code is currently used: there are no definitions of
struct sdhci_plat_data in arch/arm, neither are there any DT properties
which use card_power_gpio/power_active_high/power_always_enb. In any
case, slot power control should be rigged up via vmmc and the regulator
subsystem in the DT case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <chris@printf.net>
Use devm_ioremap_resource() to simplify iomem resource handling in the
probe path.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci-spear is unsafe should a probe fail or defer, since it overwrites
the platform_data with its own driver-private data. It's trivial to
fix as SDHCI allows for driver-private data to be appended to its own
structure - we just need to arrange the code to allow this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <chris@printf.net>
Fix the error handling paths for DT and simplify using the devm_* API
for clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <chris@printf.net>
`sdhci_bcm_kona_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Fixes: 058feb5366 ("mmc: sdhci-bcm-kona: make linker-section warning go away")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Mayer <markus.mayer@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add set block count command support for close ended multiblock read/write.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
split start dma function into setup and start dma to keep track of
host_cookie when cmd23 support is enabled along with async request.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
