There's a small delay after setting ASPM in vendor drivers, r8101 and
r8168.
In addition, those drivers enable ASPM before ClkReq, also change that
to align with vendor driver.
I haven't seen anything bad becasue of this, but I think it's better to
keep in sync with vendor driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes kcm users know they need to look for the
strparser offset within their bpf program, which is not documented
anywhere and examples laying around do not do.
The actual recv function does handle the offset well, so we can create a
temporary clone of the skb and pull that one up as required for parsing.
The pull itself has a cost if we are pulling beyond the head data,
measured to 2-3% latency in a noisy VM with a local client stressing
that path. The clone's impact seemed too small to measure.
This bug can be exhibited easily by implementing a "trivial" kcm parser
taking the first bytes as size, and on the client sending at least two
such packets in a single write().
Note that bpf sockmap has the same problem, both for parse and for recv,
so it would pulling twice or a real pull within the strparser logic if
anyone cares about that.
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning:
drivers/net/ethernet/microchip/lan743x_main.c:2964:12: warning: lan743x_pm_suspend defined but not used [-Wunused-function]
static int lan743x_pm_suspend(struct device *dev)
drivers/net/ethernet/microchip/lan743x_main.c:2987:12: warning: lan743x_pm_resume defined but not used [-Wunused-function]
static int lan743x_pm_resume(struct device *dev)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c50 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kTLS MSG_PEEK behavior is currently failing, strace example:
[pid 2430] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 3
[pid 2430] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 4
[pid 2430] bind(4, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("0.0.0.0")}, 16) = 0
[pid 2430] listen(4, 10) = 0
[pid 2430] getsockname(4, {sa_family=AF_INET, sin_port=htons(38855), sin_addr=inet_addr("0.0.0.0")}, [16]) = 0
[pid 2430] connect(3, {sa_family=AF_INET, sin_port=htons(38855), sin_addr=inet_addr("0.0.0.0")}, 16) = 0
[pid 2430] setsockopt(3, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0
[pid 2430] setsockopt(3, 0x11a /* SOL_?? */, 1, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0
[pid 2430] accept(4, {sa_family=AF_INET, sin_port=htons(49636), sin_addr=inet_addr("127.0.0.1")}, [16]) = 5
[pid 2430] setsockopt(5, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0
[pid 2430] setsockopt(5, 0x11a /* SOL_?? */, 2, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0
[pid 2430] close(4) = 0
[pid 2430] sendto(3, "test_read_peek", 14, 0, NULL, 0) = 14
[pid 2430] sendto(3, "_mult_recs\0", 11, 0, NULL, 0) = 11
[pid 2430] recvfrom(5, "test_read_peektest_read_peektest"..., 64, MSG_PEEK, NULL, NULL) = 64
As can be seen from strace, there are two TLS records sent,
i) 'test_read_peek' and ii) '_mult_recs\0' where we end up
peeking 'test_read_peektest_read_peektest'. This is clearly
wrong, and what happens is that given peek cannot call into
tls_sw_advance_skb() to unpause strparser and proceed with
the next skb, we end up looping over the current one, copying
the 'test_read_peek' over and over into the user provided
buffer.
Here, we can only peek into the currently held skb (current,
full TLS record) as otherwise we would end up having to hold
all the original skb(s) (depending on the peek depth) in a
separate queue when unpausing strparser to process next
records, minimally intrusive is to return only up to the
current record's size (which likely was what c46234ebb4
("tls: RX path for ktls") originally intended as well). Thus,
after patch we properly peek the first record:
[pid 2046] wait4(2075, <unfinished ...>
[pid 2075] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 3
[pid 2075] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 4
[pid 2075] bind(4, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("0.0.0.0")}, 16) = 0
[pid 2075] listen(4, 10) = 0
[pid 2075] getsockname(4, {sa_family=AF_INET, sin_port=htons(55115), sin_addr=inet_addr("0.0.0.0")}, [16]) = 0
[pid 2075] connect(3, {sa_family=AF_INET, sin_port=htons(55115), sin_addr=inet_addr("0.0.0.0")}, 16) = 0
[pid 2075] setsockopt(3, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0
[pid 2075] setsockopt(3, 0x11a /* SOL_?? */, 1, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0
[pid 2075] accept(4, {sa_family=AF_INET, sin_port=htons(45732), sin_addr=inet_addr("127.0.0.1")}, [16]) = 5
[pid 2075] setsockopt(5, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0
[pid 2075] setsockopt(5, 0x11a /* SOL_?? */, 2, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0
[pid 2075] close(4) = 0
[pid 2075] sendto(3, "test_read_peek", 14, 0, NULL, 0) = 14
[pid 2075] sendto(3, "_mult_recs\0", 11, 0, NULL, 0) = 11
[pid 2075] recvfrom(5, "test_read_peek", 64, MSG_PEEK, NULL, NULL) = 14
Fixes: c46234ebb4 ("tls: RX path for ktls")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
hv_netvsc: associate VF and PV device by serial number
The Hyper-V implementation of PCI controller has concept of 32 bit serial number
(not to be confused with PCI-E serial number). This value is sent in the protocol
from the host to indicate SR-IOV VF device is attached to a synthetic NIC.
Using the serial number (instead of MAC address) to associate the two devices
avoids lots of potential problems when there are duplicate MAC addresses from
tunnels or layered devices.
The patch set is broken into two parts, one is for the PCI controller
and the other is for the netvsc device. Normally, these go through different
trees but sending them together here for better review. The PCI changes
were submitted previously, but the main review comment was "why do you
need this?". This is why.
v2 - slot name can be shorter.
remove locking when creating pci_slots; see comment for explaination
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching network device based on MAC address is problematic
since a non VF network device can be creted with a duplicate MAC
address causing confusion and problems. The VMBus API does provide
a serial number that is a better matching method.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hyper-V host API for PCI provides a unique "serial number" which
can be used as basis for sysfs PCI slot table. This can be useful
for cases where userspace wants to find the PCI device based on
serial number.
When an SR-IOV NIC is added, the host sends an attach message
with serial number. The kernel doesn't use the serial number, but
it is useful when doing the same thing in a userspace driver such
as the DPDK. By having /sys/bus/pci/slots/N it provides a direct
way to find the matching PCI device.
There maybe some cases where serial number is not unique such
as when using GPU's. But the PCI slot infrastructure will handle
that.
This has a side effect which may also be useful. The common udev
network device naming policy uses the slot information (rather
than PCI address).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e9660 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Siwei Liu <loseweigh@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely case ip6_xmit() has to call skb_realloc_headroom(),
we need to call skb_set_owner_w() before consuming original skb,
otherwise we risk a use-after-free.
Bring IPv6 in line with what we do in IPv4 to fix this.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operation ~(p100_inb(VG_LAN_CFG_1) & HP100_LINK_UP) returns a value
that is always non-zero and hence the wait for the link to drop always
terminates prematurely. Fix this by using a logical not operator instead
of a bitwise complement. This issue has been in the driver since
pre-2.6.12-rc2.
Detected by CoverityScan, CID#114157 ("Logical vs. bitwise operator")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers using phylink shouldn't mess with the link carrier
themselves and should let phylink manage it. The mvpp2 driver wasn't
following this best practice as the mac_config() function made calls to
change the link carrier state. This led to wrongly reported carrier link
state which then triggered other issues. This patch fixes this
behaviour.
But the PPv2 driver relied on this misbehaviour in two cases: for fixed
links and when not using phylink (ACPI mode). The later was fixed by
adding an explicit call to link_up(), which when the ACPI mode will use
phylink should be removed.
The fixed link case was relying on the mac_config() function to set the
link up, as we found an issue in phylink_start() which assumes the
carrier is off. If not, the link_up() function is never called. To fix
this, a call to netif_carrier_off() is added just before phylink_start()
so that we do not introduce a regression in the driver.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mades TI_DAVINCI_CPDMA select GENERIC_ALLOCATOR.
without that, the following sparc64 build failure happen
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
(.text+0x278): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit':
(.text+0x340): undefined reference to `gen_pool_alloc'
(.text+0x5c4): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x64c): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.6':
davinci_cpdma.c:(.text+0x17ac): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x17b8): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x1824): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x1830): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
(.text+0x19f8): undefined reference to `devm_gen_pool_create'
(.text+0x1a90): undefined reference to `gen_pool_add_virt'
Makefile:1011: recipe for target 'vmlinux' failed
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-09-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix end boundary calculation in BTF for the type section, from Martin.
2) Fix and revert subtraction of pointers that was accidentally allowed
for unprivileged programs, from Alexei.
3) Fix bpf_msg_pull_data() helper by using __GFP_COMP in order to avoid
a warning in linearizing sg pages into a single one for large allocs,
from Tushar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
udp: add missing check on edumx rx path
The early demux RX path for the UDP protocol is currently missing
some checks. Both ipv4 and ipv6 implementations lack checksum conversion
and the ipv6 implementation additionally lack the zero checksum
validation.
The first patch takes care of UDPv4 and the second one of UDPv6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the UDPv6 early demux rx code path lacks some mandatory
checks, already implemented into the normal RX code path - namely
the checksum conversion and no_check6_rx check.
Similar to the previous commit, we move the common processing to
an UDPv6 specific helper and call it from both edemux code path
and normal code path. In respect to the UDPv4, we need to add an
explicit check for non zero csum according to no_check6_rx value.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Xin Long <lucien.xin@gmail.com>
Fixes: c9f2c1ae12 ("udp6: fix socket leak on early demux")
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2abb7cdc0d ("udp: Add support for doing checksum
unnecessary conversion") left out the early demux path for
connected sockets. As a result IP_CMSG_CHECKSUM gives wrong
values for such socket when GRO is not enabled/available.
This change addresses the issue by moving the csum conversion to a
common helper and using such helper in both the default and the
early demux rx path.
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Reobert O'Callahan, since Viro's commit to kill
dev_ifsioc() we attempt to copy too much data in compat mode,
which may lead to EFAULT when the 32-bit version of struct ifreq
sits at/near the end of a page boundary, and the next page isn't
mapped.
Fix this by passing the approprate compat/non-compat size to copy
and using that, as before the dev_ifsioc() removal. This works
because only the embedded "struct ifmap" has different size, and
this is only used in SIOCGIFMAP/SIOCSIFMAP which has a different
handler. All other parts of the union are naturally compatible.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199469.
Fixes: bf4405737f ("kill dev_ifsioc()")
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a GSO segment that consists of encapsulated packets, the
skb->mac_len of the segments can end up being set wrong, causing packet
drops in particular when using act_mirred and ifb interfaces in
combination with a qdisc that splits GSO packets.
This happens because at the time skb_segment() is called, network_header
will point to the inner header, throwing off the calculation in
skb_reset_mac_len(). The network_header is subsequently adjust by the
outer IP gso_segment handlers, but they don't set the mac_len.
Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6
gso_segment handlers, after they modify the network_header.
Many thanks to Eric Dumazet for his help in identifying the cause of
the bug.
Acked-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2018-09-13
A few Bluetooth fixes for the 4.19-rc series:
- Fixed rw_semaphore leak in hci_ldisc
- Fixed local Out-of-Band pairing data handling
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
tls: don't leave keys in kernel memory
There are a few places where the RX/TX key for a TLS socket is copied
to kernel memory. This series clears those memory areas when they're no
longer needed.
v2: add union tls_crypto_context, following Vakul Garg's comment
swap patch 2 and 3, using new union in patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This contains key material in crypto_send_aes_gcm_128 and
crypto_recv_aes_gcm_128.
Introduce union tls_crypto_context, and replace the two identical
unions directly embedded in struct tls_context with it. We can then
use this union to clean up the memory in the new tls_ctx_free()
function.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to copy the key to an on-stack buffer before calling
crypto_aead_setkey().
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update 'confirmed' timestamp when ARP packet is received. It shouldn't
affect locktime logic and anyway entry can be confirmed by any higher-layer
protocol. Thus it makes sense to confirm it when ARP packet is received.
Fixes: 77d7123342 ("neighbour: update neigh timestamps iff update is effective")
Signed-off-by: Vasily Khoruzhick <vasilykh@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix addresses https://bugzilla.kernel.org/show_bug.cgi?id=201071
Commit 5025f7f7d5 wrongly relied on __dev_change_flags to notify users of
dev flag changes in the case when dev->rtnl_link_state = RTNL_LINK_INITIALIZED.
Fix it by indicating flag changes explicitly to __dev_notify_flags.
Fixes: 5025f7f7d5 ("rtnetlink: add rtnl_link_state check in rtnl_configure_link")
Reported-By: Liam mcbirnie <liam.mcbirnie@boeing.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fields ->dev and ->next of struct ipddp_route may be copied to
userspace on the SIOCFINDIPDDPRT ioctl. This is only accessible
to CAP_NET_ADMIN though. Let's manually copy the relevant fields
instead of using memcpy().
BugLink: http://blog.infosectcbr.com.au/2018/09/linux-kernel-infoleaks.html
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we delete a chain of filters, we need to notify
user-space we are deleting each filters in this chain
too.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 57f230ab04 ("xen/netfront: raise max number of slots in
xennet_get_responses()") raised the max number of allowed slots by one.
This seems to be problematic in some configurations with netback using
a larger MAX_SKB_FRAGS value (e.g. old Linux kernel with MAX_SKB_FRAGS
defined as 18 instead of nowadays 17).
Instead of BUG_ON() in this case just fall back to retransmission.
Fixes: 57f230ab04 ("xen/netfront: raise max number of slots in xennet_get_responses()")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In inet6_rtm_getroute, since Commit 93531c6743 ("net/ipv6: separate
handling of FIB entries from dst based routes"), it has used rt->from
to dump route info instead of rt.
However for some route like cache, some of its information like flags
or gateway is not the same as that of the 'from' one. It caused 'ip
route get' to dump the wrong route information.
In Jianlin's testing, the output information even lost the expiration
time for a pmtu route cache due to the wrong fib6_flags.
So change to use rt6_info members for dst addr, src addr, flags and
gateway when it tries to dump a route entry without fibmatch set.
v1->v2:
- not use rt6i_prefsrc.
- also fix the gw dump issue.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbmLg2AAoJEAx081l5xIa+794QAJeBd7XnrQtMS+BWMet0G4Dh
yY1t3LAsP75GiyI73Zbf1mWIdNk1hxli9+9+XVSrK9Yt2oh/AD+Q8BBGW7V3b17S
BvpAhKdQNJut8NskfTKvFE5lz/oMrJCKYFYh/vwigfOXo9ELg9imUcKMQJqHLzPP
SEiS4EgQ00h97FSodqYLj8E8sSIGx61xKkCBgczcpXq6SrxQAIZGW0Ut7cKUebl+
VON1sccI6xKCqVHqv/mqkm/Cugc5c6bj+AUII9NvXljAKptNjb8c813XbjwCCfzC
5OMX084ZXl94jAbqZjJXDYu640tkUpx1+o3eJZOfWz4dM7oTWU59+AHxytQWmF8P
T73o9+r93cQSP0YUb070LkSPr/YSBldb3PFk22mzRX1kHeHPuLzMGGr37Xj/3RI9
Uilddus6n2S7JzLdPl3RNLnDfVwRopc/E7VUbUCMDKrbHjV2tvsyZvBDDgPXCU68
cxG/VXKQsa4yicMbXUCjl+vGwaXZLve1wGGx/ee9Ooaqa7b7L297NWpxqhl3PjhL
G2gySbwa7gItRPw34fhNlzmEoNFk+JyAp3EOYOZQM78+IBKRSwhDVJOrbAjY+H1F
c+sUOdBk+yLQ15MVbhFeq+1puJETnV3ZmJgHjNDUUhRcJamilqfLBNiNUfGm4Pqp
9E8QZTq8BgZqWJE9ep0m
=GbIW
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2018-09-12' of git://anongit.freedesktop.org/drm/drm
Pull drm nouveau fixes from Dave Airlie:
"I'm sending this separately as it's a bit larger than I generally like
for one driver, but it does contain a bunch of make my nvidia laptop
not die (runpm) and a bunch to make my docking station and monitor
display stuff (mst) fixes.
Lyude has spent a lot of time on these, and we are putting the fixes
into distro kernels as well asap, as it helps a bunch of standard
Lenovo laptops, so I'm fairly happy things are better than they were
before these patches, but I decided to split them out just for
clarification"
* tag 'drm-fixes-2018-09-12' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/disp/gm200-: enforce identity-mapped SOR assignment for LVDS/eDP panels
drm/nouveau/disp: fix DP disable race
drm/nouveau/disp: move eDP panel power handling
drm/nouveau/disp: remove unused struct member
drm/nouveau/TBDdevinit: don't fail when PMU/PRE_OS is missing from VBIOS
drm/nouveau/mmu: don't attempt to dereference vmm without valid instance pointer
drm/nouveau: fix oops in client init failure path
drm/nouveau: Fix nouveau_connector_ddc_detect()
drm/nouveau/drm/nouveau: Don't forget to cancel hpd_work on suspend/unload
drm/nouveau/drm/nouveau: Prevent handling ACPI HPD events too early
drm/nouveau: Reset MST branching unit before enabling
drm/nouveau: Only write DP_MSTM_CTRL when needed
drm/nouveau: Remove useless poll_enable() call in drm_load()
drm/nouveau: Remove useless poll_disable() call in switcheroo_set_state()
drm/nouveau: Remove useless poll_enable() call in switcheroo_set_state()
drm/nouveau: Fix deadlocks in nouveau_connector_detect()
drm/nouveau/drm/nouveau: Use pm_runtime_get_noresume() in connector_detect()
drm/nouveau/drm/nouveau: Fix deadlock with fb_helper with async RPM requests
drm/nouveau: Remove duplicate poll_enable() in pmops_runtime_suspend()
drm/nouveau/drm/nouveau: Fix bogus drm_kms_helper_poll_enable() placement
Pull networking fixes from David Miller:
1) Fix up several Kconfig dependencies in netfilter, from Martin Willi
and Florian Westphal.
2) Memory leak in be2net driver, from Petr Oros.
3) Memory leak in E-Switch handling of mlx5 driver, from Raed Salem.
4) mlx5_attach_interface needs to check for errors, from Huy Nguyen.
5) tipc_release() needs to orphan the sock, from Cong Wang.
6) Need to program TxConfig register after TX/RX is enabled in r8169
driver, not beforehand, from Maciej S. Szmigiero.
7) Handle 64K PAGE_SIZE properly in ena driver, from Netanel Belgazal.
8) Fix crash regression in ip_do_fragment(), from Taehee Yoo.
9) syzbot can create conditions where kernel log is flooded with
synflood warnings due to creation of many listening sockets, fix
that. From Willem de Bruijn.
10) Fix RCU issues in rds socket layer, from Cong Wang.
11) Fix vlan matching in nfp driver, from Pieter Jansen van Vuuren.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
nfp: flower: reject tunnel encap with ipv6 outer headers for offloading
nfp: flower: fix vlan match by checking both vlan id and vlan pcp
tipc: check return value of __tipc_dump_start()
s390/qeth: don't dump past end of unknown HW header
s390/qeth: use vzalloc for QUERY OAT buffer
s390/qeth: switch on SG by default for IQD devices
s390/qeth: indicate error when netdev allocation fails
rds: fix two RCU related problems
r8169: Clear RTL_FLAG_TASK_*_PENDING when clearing RTL_FLAG_TASK_ENABLED
erspan: fix error handling for erspan tunnel
erspan: return PACKET_REJECT when the appropriate tunnel is not found
tcp: rate limit synflood warnings further
MIPS: lantiq: dma: add dev pointer
netfilter: xt_hashlimit: use s->file instead of s->private
netfilter: nfnetlink_queue: Solve the NFQUEUE/conntrack clash for NF_REPEAT
netfilter: cttimeout: ctnl_timeout_find_get() returns incorrect pointer to type
netfilter: conntrack: timeout interface depend on CONFIG_NF_CONNTRACK_TIMEOUT
netfilter: conntrack: reset tcp maxwin on re-register
qmi_wwan: Support dynamic config on Quectel EP06
ethernet: renesas: convert to SPDX identifiers
...
Helper bpg_msg_pull_data() can allocate multiple pages while
linearizing multiple scatterlist elements into one shared page.
However, if the shared page has size > PAGE_SIZE, using
copy_page_to_iter() causes below warning.
e.g.
[ 6367.019832] WARNING: CPU: 2 PID: 7410 at lib/iov_iter.c:825
page_copy_sane.part.8+0x0/0x8
To avoid above warning, use __GFP_COMP while allocating multiple
contiguous pages.
Fixes: 015632bb30 ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Subtraction of pointers was accidentally allowed for unpriv programs
by commit 82abbf8d2f. Revert that part of commit.
Fixes: 82abbf8d2f ("bpf: do not allow root to mangle valid pointers")
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski says:
====================
nfp: flower: fixes for flower offload
Two fixes for flower matching and tunnel encap. Pieter fixes
VLAN matching if the entire VLAN id is masked out and match
is only performed on the PCP field. Louis adds validation of
tunnel flags for encap, most importantly we should not offload
actions on IPv6 tunnels if it's not supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug where ipv6 tunnels would report that it is
getting offloaded to hardware but would actually be rejected
by hardware.
Fixes: b27d6a95a7 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the vlan id field is present when trying
to match a vlan tag. The vlan id and vlan pcp field should be treated
independently.
Fixes: 5571e8c9f2 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __tipc_dump_start() fails with running out of memory,
we have no reason to continue, especially we should avoid
calling tipc_dump_done().
Fixes: 8f5c5fcf35 ("tipc: call start and done ops directly in __tipc_nl_compat_dumpit()")
Reported-and-tested-by: syzbot+3f8324abccfbf8c74a9f@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-09-12
please apply the following qeth fixes for -net.
Patch 1 resolves a regression in an error path, while patch 2 enables
the SG support by default that was newly introduced with 4.19.
Patch 3 takes care of a longstanding problem with large-order
allocations, and patch 4 fixes a potential out-of-bounds access.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For inbound data with an unsupported HW header format, only dump the
actual HW header. We have no idea how much payload follows it, and what
it contains. Worst case, we dump past the end of the Inbound Buffer and
access whatever is located next in memory.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_query_oat_command() currently allocates the kernel buffer for
the SIOC_QETH_QUERY_OAT ioctl with kzalloc. So on systems with
fragmented memory, large allocations may fail (eg. the qethqoat tool by
default uses 132KB).
Solve this issue by using vzalloc, backing the allocation with
non-contiguous memory.
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scatter-gather transmit brings a nice performance boost. Considering the
rather large MTU sizes at play, it's also totally the Right Thing To Do.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
