Uses the drm ELD core framework to apply rate and channel
Also compute the format to be set based on ELD.
Even though the channel constraint is based on ELD, infoframe
is set with stereo only. Multichannel support will be added
later.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses i915 component framework to register for hotplug
notification.
In the hotplug notification, driver reads pin sense and ELD by
sending PIN_SENSE and ELD verbs over HDA bus. Once it identifies
valid pin sense and valid ELD, store the ELD into the
corresponding pin map buffer.
Also read the monitor present sense during resume and ignore the
ELD notify from graphics during PM as is done in legacy hda,
commit 8ae743e82f ("ALSA: hda - Skip ELD notification during
system suspend")
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the FLL is in pseudo-fractional mode there is an additional
limit on fref based on the fratio, to prevent aliasing around the
Nyquist frequency. If fref exceeds this limit the refclk divider
must be increased and the calculation tried again until a suitable
combination of fref and fratio is found or we have to fall back to
integer mode.
This patch also adds some debug log prints around this code.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Forwarding the return value of i2c_master_send, leads to errors
later on, since i2c_master_send returns the number of bytes
transmittet. Check for ret < 0 instead and return 0 otherwise.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some configurations, the dai registers get written before the bias
level is changed in the codec driver. This leads to a situation where
an initial write to the serial port register gets ignored, and future
writes may as well, since regmap thinks that the codec already holds the
value. More specifically, configuring the codec as i2s master would in
fact result in the codec running as slave, a situation where no i2s
clocks are generated and hence no data is transferred.
This change makes sure that regmap only caches writes when the core
clock is disabled, and syncs regmap whenever enabling the core clock
again.
Signed-off-by: Andreas Irestål <andire@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When playback mono wav with record in background, there will be some
nosie in the right dac channel. It seems that the ADC data has been
routed to the dac channel.
The cs42888 have 8 dac channels, it's appropriate to mute the unused
dac channels, and the noise will disappear.
Steps to reproduce this issue:
arecord -D hw:0,0 -f S16_LE -r 48000 -c 1 a.wav &
aplay -Dhw:0,0 audio48k16M.wav
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt5514. The codec includes a low power
DSP for voice wake up. The register address is incremental by 4 in the DSP
memory map. In order to recover the codec settings in the codec mode and
manipulate the DSP mode for voice wake up, we use the multi-level register
map. One is for ALSA API in codec mode that can be recovered by cache
before recording. Another is for DSP related settings that can be accessed
with 32bit address of the DSP in the application of voice wake up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should return a valid sample rate from the pointer callback, this
patch adds this into the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds firmware compressed stream capture support
and DAI hookups for voice control firmware (based on the wm5110
implementation.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm5102 also supports the audio trace firmware, this patch adds support
for this into the wm5102 driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly this adds DAI links for the audio trace, however, it is also
necessary to update the data IRQ handler to check more cores. We have
the handler check every core so it should not be necessary to update
this function if more compressed firmwares are added in the future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reference the TRM, the ALC5616 support one 24bit/8KHz ~ 192KHz
I2S/PCM Interface for stereo DAC and stereo ADC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM179x family supports both SPI and I2C. This patch adds support
for the I2C interface.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pcm179x family supports both SPI and I2C for configuration. This
patch splits the driver into core and SPI parts, in preparation for
I2C support.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADSP code should be agnostic of which CODEC it runs upon, currently
there is only one remaining part of the implementation that doesn't
follow this. When the DSP is booted on ADSP2 we read
ARIZONA_SYSTEM_CLOCK_1 and use that to set the initial speed for the DSP
clock. This patch factors that out into CODEC specific code, leaving the
ADSP code entirely CODEC agnostic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio trace firmware allows the capture of arbitrary streams of
audio from the DSP and commonly used for debugging other firmwares. This
patch adds support for this firwmare into the ADSP driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The region definition will be shared by most firmwares so give this a
more generic name and whilst we are there improve the naming of the
voice control capabilities array as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst there is nothing wrong with the error path here it looks a little
bit odd, this patches makes the code a little more idiomatic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the code to enable the clock to the CODEC driver
if it needs the clock enabled.
In some case, We need to claim the clock which is driving the codec
so that when we enable clock gating, we continue to clock the codec
when needed.
if mclk provided, to enable and disable the clock source.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch try to fix the trivial typo.
Run "scripts/checkpatch.pl -f --subjective xxx"
The enable more subjective tests.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SND_SOC_INNO_RK3036 is enabled but REGMAP_MMIO is not, the MODPOST
step fails with this error:
...
Kernel: arch/x86/boot/bzImage is ready (#3)
Building modules, stage 2.
MODPOST 3203 modules
ERROR: "__devm_regmap_init_mmio_clk" [sound/soc/codecs/snd-soc-inno-rk3036.ko] undefined!
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the ssm4567 is powered up the driver calles regcache_sync() to restore
the register map content. regcache_sync() assumes that the device is in its
power-on reset state. Make sure that this is the case by explicitly
resetting the ssm4567 register map before calling regcache_sync() otherwise
we might end up with a incorrect register map which leads to undefined
behaviour.
One such undefined behaviour was observed when returning from system
suspend while a playback stream is active, in that case the ssm4567 was
kept muted after resume.
Fixes: 1ee44ce030 ("ASoC: ssm4567: Add driver for Analog Devices SSM4567 amplifier")
Reported-by: Harsha Priya <harshapriya.n@intel.com>
Tested-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a set_sysclk() DAI op so the card driver can set the
input clock frequency. If this is done, the pll and mclk divider
are configured to produce the required 256x fs clock when the
sample rate is set by hw_params().
These additions make the codec work with the simple-card driver.
Card drivers calling set_pll() and set_clkdiv() directly are
unaffected.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'break' here is not useful after 'return' or 'goto'.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of WM8960_SYSCLK_AUTO mode, WM8960_SYSCLK_PLL mode was
made unusable. Ensure we're not PLL mode before trying to use MCLK.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
INBMIX1 controls LINPUTs and INBMIX2 controls RINPUTs, so fix the naming
accordingly.
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was not unregistering the compressed platform in
wm5110_remove(). If the codec is built as a module, this would
lead to a NULL pointer deref if the module was unloaded and then
re-probed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added rt5659 codec driver unconditionally defines an
ACPI device match table but then uses ACPI_PTR() to remove the
only reference to it, so we get a harmless build warning:
sound/soc/codecs/rt5659.c:4200:30: warning: 'rt5659_acpi_match' defined but not used [-Wunused-variable]
static struct acpi_device_id rt5659_acpi_match[] = {
This changes both the OF match table and the ACPI match table
to follow the same style, using ACPI_PTR/of_match_ptr to
make the reference conditional, and using an #ifdef to hide
the table. This also adds the missing MODULE_DEVICE_TABLE for
the OF case and adapts the formatting to the same style.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift bit of IN1 boost gain control is 12.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
RT286_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT286_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt286_set_bias_level and
rt298_vref_event to rt286_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module. The rt5659->i2c is no longer used after this conversion, thus
remove it as well.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWee4AAAoJECTWi3JdVIfQwPkH/jMpijne8cfnOm0jQ0WyvXPd
HSig93ZAJ2x/+uR7yrmF2BsxhnT6G1lmDb2zxYhHGEAMyBtdA/xtOjO1wTRjXgIo
9p7ui66uP/sAW+NfHsvXVyf/8vV9nw8t0CsyBf+ijynz6MiDigQR7e8RA7xZR7oQ
oBabHPZb85OJjxmn2XlqaxUoxNhBdAS3gNoctMy9VZDwSLiunOvYTGBoBA43LQk6
6DN5VRu7wg05ruN6t5xZ5bd5WAtvgN+tSsRAabmunWDnILCa8OaOmzWPv3QITIva
PQLauiya4N0/YgyNGYaBY/6pc5u9SHzq0caYUq0I6WY6Phjo7wfU8/+y4NqUPn4=
=d18k
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.5' into asoc-next
ASoC: Updates for v4.5
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
# gpg: Signature made Wed 23 Dec 2015 00:42:40 GMT using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
A recent rework removed the only user of the hdac_hdmi_query_pin_connlist
function, so we now get a warning when building the hdac_hdmi driver:
hdac_hdmi.c:313:12: warning: 'hdac_hdmi_query_pin_connlist' defined but not used [-Wunused-function]
This removes the function, which makes the file build cleanly again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 15b914476b ("ASoC: hdac_hdmi: Use list to add pins and converters")
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm1792a is compatible with pcm1795 and pcm1796 so it's
better to have them under the common name pcm179x
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Future platforms may have a different set of pins/converters.
So use lists to add pins and converters based on enumeration.
Also it may be required to connect any converter to any pin
dynamically as per different use cases (for example DP is
connected to pin 6 on skylake board). So this will help in
dynamically select and route.
Fix the dai map as well to use the pin/cvt from list. Not
enabling all dai maps for now.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/RINPUT1 can line to Left/Right Boost Mixer through boost switch.
If boost switch is open, there will be no voice when using L/RINPUT1.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In normal operation, the left and right channel digital audio data is
converted to analogue in two separate DACs. There is a mono-mix mode
where the two audio channels are mixed together digitally and then
converted to analogue using only one DAC, while the other DAC is
switched off. The mono-mix signal can be selected to appear on both
analogue output channels. The mono mix is automatically attenuated by
6dB to prevent clipping.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible that some pin widget may return with no converter
connected. So don't throw error if none are found to be connected.
Instead print a warning and continue.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Data is read in blocks of up to one fragment is size from the circular
buffer on the DSP and is re-packed to remove the padding byte that
exists in the DSP memory map.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here support is added for responding to DSP IRQs that are used to
indicate data being available on the DSP. The idea is that we check the
amount of data available upon receipt of an IRQ and on subsequent calls
to the pointer callback we recheck once less than one fragment is
available (to avoid excessive SPI traffic), if there is truely less than
one fragment available we ack the last IRQ and wait for a new one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't want to use a bypassed write in wm5110_clear_pga_volume,
we might disable the DRE whilst the CODEC is powered down. A
normal regmap_write will always go to the hardware (when not on
cache_only) even if the written value matches the cache. As using
a normal write will still achieve the desired behaviour of bring
the cache and hardware in sync, this patch updates the function
to use a normal write, which avoids issues when the CODEC is
powered down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
commit 3c83ac2325 ("ASoC: hdac_hdmi: check error return") fixes
the static checker warning reported by Dan Carpenter:
sound/soc/codecs/hdac_hdmi.c:416 hdac_hdmi_parse_and_map_nid()
warn: unsigned 'hdac->num_nodes' is never less than zero.
But it doesn't fix the issue completely.
It's also a failure if no sub nodes found for an afg node. So modify
the return condition appropriately.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the device latches data on the falling edge of the
BCLK in DSP mode, whereas the expectation for normal BCLK is to
latch on the rising edge. This updates the driver to invert the
BCLK configuration for DSP mode, to align with expected behaviour.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the device latches data on the falling edge of the
BCLK in DSP mode, whereas the expectation for normal BCLK is to
latch on the rising edge. This updates the driver to invert the
BCLK configuration for DSP mode, to align with expected behaviour.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BIOS for the HP ElitePad 1000 G2 uses an unexpected HID,
(INTCCFFD), add it to the white list of knowns HIDs.
Signed-off-by: Jorge Fernandez Monteagudo <jorgefm@cirsa.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IRQ reaction time is not immediate when headset putton is pressed.
This patch shortens the reaction time.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Constify the ACPI device ID array, no need to have it writable at
runtime. Also drop the unused RT5645_INIT_REG_LEN define.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_to_hdac_dev() and to_ehdac_device() instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 9b8ef9f6b3 ("ASoC: dapm: Add startup & shutdown for dai_links")
Added support for calling startup on CODEC to CODEC links, however this
is called with a NULL runtime pointer. There isn't really a sensible way
to pass a valid runtime pointer to a CODEC to CODEC link at the moment,
so we need to make the startup function safe for NULL runtimes.
This patch returns from the Arizona startup function early if there is no
runtime, this is perfectly safe as all the startup function does is set
the PCM constraints for user-space which arn't relevant to a CODEC to
CODEC link anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of call sites were missed when the snd_soc_dapm_mutex_lock
function was added this patch fixes those up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add system clock detection to prevent output DC from SPO.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ pin will keep high when the headset button is pressed. And
keep low when the headset button is released. So, we need irq trigger
at both edges. However, some platform can't support it. Therefore,
we polling the register to report the button release event once a
button presse event is received.
To support the headset button detection function for those can't
support both edges trigger platforms, we also need to invert the
polarity of jack detection irq since we need to keep the IRQ pin
low in normal case.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial silicon did not have master bias enabled by default, unlike
later HW, so use regmap patch to align with newer defaults.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as
we test for a multiple of 8kHz. This patch fixes this issue by testing
for multiples of 4kHz instead.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add required tables and the binding document for ACPI and OF matching.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a status bit on RT5677_PLL1_CTRL2 and RT5677_PLL2_CTRL2.
That's why those registers are set volatile. However, the status
bit is currently not used by codec driver. So, it should be no
problem if we set them non-volatile.
The purpose of setting them non-volatile is to restore the setting
after a syspend/resume cycle.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream is created whilst the compressed stream is opened and a
buffer is created when the DSP powers up. It is necessary at a point
once both the DSP has powered up and the the stream has been opened to
connect a stream to a buffer on the DSP. This is done in the trigger
callback as this is after the DSP has been powered and obviously the
stream must be open. Note that whilst the connect is currently trivial
it is expected that this will get more complex when support for multiple
buffers/streams per DSP is added.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code that locates and initialises the buffer of compressed data on
the DSP if the firmware supported compressed data capture. The buffer
struct (wm_adsp_compr_buf) is kept separate from the stream struct
(wm_adsp_compr) this will allow much easier support of multiple
streams of data from the one DSP in the future, although support for
this will not be added in this patch chain.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow user-space to open a compressed stream, although no data will be
passed yet, as part of this adding the ability to define supported
capabilities per firmware and check these match the stream being opened.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register a platform driver for the CODEC and add DAIs that will be used
to connect a compressed record path for the voice control functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL mode based on 32KHz master clock not supported in
AB silicon so remove support from the driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW can provide 1.6V micbias level as well the existing levels
already provided in the driver. This patch adds support for 1.6V
to the DT binding.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AB silicon, the internal LDO is not supported so remove
DT and driver references to this (digital voltage direct from
'VDD' supply)
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current AB silicon, BIAS_EN field is enabled by default in the
REFERENCES register, so the regmap default value should reflect
this.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If codec probe() function fails after supplies have been enabled
it should really tidy up and disable them again. This patch updates
the probe function to do just that.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously Sidetone would operate only when capture to DAI was in
progress, due to DAPM path configuration. There is no reason why
this should not operate without DAI capture, so this patch updates
the DAPM path accordingly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return type "unsigned int" was used by the ssm2518_lookup_mcs()
function even though it will eventually return a negative error code.
Improve this implementation detail by deletion of the type modifier then.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to the codec driver to handle mic level
detect related IRQs, and report these to user-space using a uevent
variable.
The uevent variable string "EVENT=MIC_LEVEL_DETECT" is sent to
user-space, if the mic level detect feature is enabled, and the
audio captured at the chosen mic(s) is above a certain threshold.
User-space can then handle the event accordingly (e.g. process
audio capture stream).
This method was chosen over ALSA control notification for a couple
of reasons:
1) There's no requirement here for a control to read state from.
The event is the only thing that's required and of interest.
2) tinyalsa support for control notifications does not exist so on
platforms using this over alsa-lib there is a need to add code
to support this event handling.
Another possible option would be to use the standard Jack reporting
framework but this really does not fit for this kind of event.
Finally, use of the input device framework is not being encouraged,
due to difficulties in enabling apps to access input devices, so
this has also been avoided.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds devicetree support to the wm8974 codec driver.
With a DT-based kernel, there is no board-specific setting
to select the driver so allow it to be manually chosen.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding ACPI ID "MX98357A" for the MAXIM 98357A amp.
Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When power up, a "pop" is heard on line-in and mic-in.
An analysis of the PCM shows it lasts ~400ms
and looks like a filter response.
VAG power up should be delayed by 400ms as VAG power down is.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Older firmwares don't specify access flags for the controls,
unfortunately the usage of some of these firmware relies on being able
to read back values from the DSP. The current control code will only do
this for volatile controls. This patch will read the control from the
hardware if no flags are specified and the control is currently
enabled, which should cover these legacy use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes PLL1 stops working if the codec loses power
during suspend (when pow-ldo2 or reset gpio is used).
MX-7Bh(RT5677_PLL1_CTRL2) is cleared and won't be restored
by regcache since it's volatile. MX-7Bh has one status bit
and M code for PLL1. rt5677_set_dai_pll doesn't reconfigure
PLL1 after resume because it thinks the PLL params are not
changed.
This patch clears the cached PLL params at resume so that
rt5677_set_dai_pll can reconfigure the PLL after resume.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch rearranges the switch statement in arizona_calc_fratio so
that older codecs are the special cases, with the default case
applying to newer codecs (WM8998 and later). This is preferable
because it avoids having to patch new cases in every time a new
codec is added.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Locking is currently missing from the DSP firmware controls, which can
lead to some race conditions if the controls are accessed as the DSP
powers up or down. This patch adds them to the new power lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should hold the DSP power lock whilst changing the firmware since we
need to check if it is running first.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most events around the DSP just need to be locked to ensure that the DSP
can't change power state whilst they are happening. This includes the
debugfs entries and this will make sorting the rest of the locking
simpler.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Attempting to use this codec driver triggers a BUG() in regcache_sync()
since no cache type is set. The register map of this device is fairly
small and has few holes so a flat cache is suitable.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
These are all off by one; the playback and bypass switches are the top
two bits of the registers, which are at shifts 7 and 6 not 8 and 7.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is using completely the wrong mask and value when updating the
register. Since the correct values are already defined in the header,
switch to using a table with explicit constants rather than shifting the
array index.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When building the da7218 driver on a 64-bit architecture, we get
a harmless warning:
sound/soc/codecs/da7218.c: In function 'da7218_of_get_id':
sound/soc/codecs/da7218.c:2261:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
This changes the code to use uintptr_t to ensure we have an integer
type of the same size as a pointer and won't get a warning on any
architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4d50934abd ("ASoC: da7218: Add da7218 codec driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Both the sysclk and asyncclk members of arizona_priv are signed by we
refer to them through an unsigned pointer. This patch fixes this small
harmless error.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, various places in Arizona use "const char *" and "int".
This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/da7218.c:3214:9-10: WARNING: return of 0/1 in function 'da7218_volatile_register' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As hdac->num_nodes is unsigned we can not check if
snd_hdac_get_sub_nodes() has returned error or success. Lets have a
temporary int to check the error value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching between two clock sources using the FLL freerun to smooth
the transition we should wait 32uS after putting the FLL into freerun
before we proceed. In practice we appear to be getting enough delay from
the surrounding code, but better to make it explicit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are more and more google projects need to use DMI to get the
platform data configuration. And those projects use the same
configuration. To clean those redundant code, we define a general
DMI for those projects with the same platform data configuration.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for DA7217 and DA7218 audio codecs.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expand the list of available firmware names to include a good selection
of generic uses for the DSP cores.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add platform specific data for Terra project.
Signed-off-by: Luke_Yin@asus.com <Luke_Yin@asus.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kzalloc() can return NULL if it fails, and then we will be dereferencing
a NULL pointer.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/inno_rk3036.c:480:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK3036 SoC integrated with an Inno audio codec.
This driver implements the functions of it.
There is not need a special machine driver, since the
simple-card machine driver works perfect in this case.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since driver use infoframe symbols from video/hdmi.c we should select this
symbol for this driver
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the component framework to keep the display on till the
playback in progress.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses hdmi framework in video to fill audio infoframe.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ops are used for triggering HDMI streams and configuring
the parameters
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power up/down the AFG node during runtime resume/suspend.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds HDA based HDMI driver to be used in platforms like SKL
and onwards
Register the hdmi driver with hda bus and register dais.
Also parse the widget and initialize identified pin and converter
widgets.
For simplification, currently only one pin and one converter
widget are enabled on board, as well as limit the rates supported
to simples ones and not based on ELD. This things will come
eventually once basic support for this is merged
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
a3af0c65("ASoC: ak4613: add single-end optional property for IN/OUT pins")
added IN/OUT pin single-end optional property, but it used "ak4613" as
vendor prefix. This patch fixup to asahi-kasei.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These are all off by one; the playback and bypass switches are the top
two bits of the registers, which are at shifts 7 and 6 not 8 and 7.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5110 device contains a hardware ANC block, this patch connects up
controls and routing for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bit allocation for PLL source is 0x80 [13:11] instead of [12:11]
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code set DFS settings on CTRL2 register, but it overwrite
default settings. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake platform also uses combo jack configuration, so add
Skylake to existing DMI match for combo jack
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pm function and fixes following issues
1.i2c timeout after resume, after resume we saw interrupt handler
is called prior to i2c controller is resumed.This causes i2c timeout
2.no audio after resume
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645.c support both rt5645 and rt5650 codec. And the default
value of registers are not identical. So we use different regmap
for the two codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTRL1 selection method didn't care about simultaneous
playback / capture. This patch tidyup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4613 IN/OUT pin can be selected as differential/single-end.
Default is differential, because it is register default settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unmuting headphone has pop noise in particular hardware design. So we extend
the delay time in headphone unmuting sequence to avoid pop.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum DMIC clock rate is 3.072 MHz for most DMIC. And it will get better
performance in higher clock rate. If we set maximum to 3 MHz in driver, we will
get a clock rate which is not even close to 3 MHz.
For example, if DMIC clock source is 24.576 MHz, the DMIC clock will be about
1.5 MHz in current code. But it will be 3.072 MHz with this patch.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert wm9713 to use the more modern registers manipulation functions,
such as snd_soc_read(), snd_soc_write() and snd_soc_update_bits().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Wolfson WM9713 to regmap API. This will leverage all the
regmap functions (debug, registers update, etc ...).
As a bonus, this will pave the path to gpio chip introduction, and
devicetree support. This was tested on the mioa701 board, pxa27x based,
in PCM playback, and through suspend/resume.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet RESET is active low pin, i.e. system goes to
reset state when pin signal is low.
The previous implementeation was assuming the pin is configured as
'active high' in DTS. Changle the gpio handling code and DTS configuration
to 'active low'.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic CS47L24 and WM1831 codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOC_xxx_DECL() macros already include 'const' so there's
no need to put a const in the source where they are used.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch changes the type of DACs mixer to AUTODISABLE and add the delay
time after power up to avoid the pop sound that comes from the filter
power.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Few codecs will meet no DMIC clock output issue when select a divided
number which is divisible by 3. To prevent this issue, the patch ignore
the numbers when calculating the DMIC clock divider.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlight is below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=l9SO
-----END PGP SIGNATURE-----
Merge tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlights are below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards"
* tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (330 commits)
ALSA: hda - Add Intel Lewisburg device IDs Audio
ALSA: hda - Apply pin fixup for HP ProBook 6550b
ALSA: hda - Fix lost 4k BDL boundary workaround
ALSA: maestro3: Fix Allegro mute until master volume/mute is touched
ALSA: maestro3: Enable docking support for Dell Latitude C810
ALSA: firewire-digi00x: add another rawmidi character device for MIDI control ports
ALSA: firewire-digi00x: add MIDI operations for MIDI control port
ALSA: firewire-digi00x: rename identifiers of MIDI operation for physical ports
ALSA: cs46xx: Fix suspend for all channels
ALSA: cs46xx: Fix Duplicate front for CS4294 and CS4298 codecs
ALSA: DocBook: Add soc-ops.c and soc-compress.c
ALSA: hda - Add / fix kernel doc comments
ALSA: Constify ratden/ratnum constraints
ALSA: hda - Disable 64bit address for Creative HDA controllers
ALSA: hda/realtek - Dell XPS one ALC3260 speaker no sound after resume back
ALSA: hda/ca0132 - Convert leftover pr_info() and pr_err()
ASoC: fsl: Use #ifdef instead of #if for CONFIG_PM_SLEEP
ASoC: rt5645: Sort the order for register bit defines
ASoC: dwc: add check for master/slave format
ASoC: rt5645: Add the HWEQ for the speaker output
...
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
Change the xinvert value from 0 to 1 on the "Capture Switch" control
WM8960 datasheet is shown as follows:
Bit 7 at 00h and 01h register address
1 : Enable Mute, 0 : Disable Mute
Signed-off-by: JongHo Kim <furmuwon@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code was able to generate illegal OPCLK_REF values because the
reference frequency tables listed all values of SYSCLK instead of
valid values for OPCLK_REF clock. The maximum OPCLK_REF clock is
49.152MHz or 45.1584MHz.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously ALC2 register is set as a volatile register, declare
it as one of ALC Coefficients register together with other non-volatile
registers will cause issue, in case wm8962 has enter suspend mode,
and cache_only flag is set, any attempt to read from ALC2 will fail.
Because the 5 status bits in ALC2 aren't used anywhere nor are useful
to end user, so this patch removes ALC2 register from volatile
register list to make ALC2 be possible to be accessed when cache_only
flag is set.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWLbbGAAoJECTWi3JdVIfQH7oH/1VdN2ozP9A03p24aC5qso1F
VWOBnG4pkw1G6J5qK2lemMDeJdRdTfreICUAa9Tw9kOSfTIb6F3X8kCw8tbwlw0I
4phgmyo23P53OfLZFMkQi/RCfwItnE0sszqhvoumUg0ryjYxg2JT+gTMgwvVo7Pq
hf6m6a3we5pxLIIYP4wlQgOKwUJe4B4nC37ExySf24Dlo/DzmWDtfQbGvmyluFzb
MB1qzEvAc/KC3LZFkIFmhfg2/caNRhcQrzkUCYrLR3t+oz9P1zCpYTII7VDdMg7L
SM2VoL+ynEAdBqa38Ozwxvd/mpHwinlAeiikuwz1PyxVOqZvZqqiWzD8eUJkhZk=
=/F/Q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
- A new driver for the Atmel Class D speaker drivers
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBF7yAAoJECTWi3JdVIfQ1MEH/jnzSyEVIuG+l8UkMaz6gf4w
zGsM1KCn//mfPl7yAoOdsnElOLR+Fmf+0jx4pCPQKrjvBGwjwH/IwBR1rwuEeUPY
7d66efpWOKlTf3qpsF1S7ZIlAZOs0NFvo0jwA1ZY/pc3YEBekyWxbABk/uWAVrM5
HJJKafI7WeiYrF0l0z2sG7BpsFtr8JKqrOVM+SGaPTNn2k+/lQ1bwTk1liOEUbsv
oq8NFNrUWPBCwbUNJQxBOvmoXC6Oa6+JBVO3+SsoS0q2FweNpqtZopjmoqHM8CiN
SkBeFT+wYlSGSnnFgAXXA2+kq74TeP2CvToo6tw+gf4LZXydKIaAdeuT6M9weZA=
=8h3u
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc2' into asoc-next
ASoC: Updates for v4.4
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
# gpg: Signature made Fri 25 Sep 2015 05:37:06 KST using RSA key ID 5D5487D0
# gpg: key CD7BEEBC: no public key for trusted key - skipped
# gpg: key CD7BEEBC marked as ultimately trusted
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: key 5C6153AD: no public key for trusted key - skipped
# gpg: key 5C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The patch adds the HWEQ function for the speaker output. User can set the
HWEQ parameters using the ALSA binary control byte-by-byte. We use the
following struct array to store the HWEQ parameters for implementing as
simple as possible.
struct rt5645_eq_param_s {
unsigned short reg;
unsigned short val;
};
It supports the variant length of the HWEQ parameters that are required.
We add the validating function in the function "rt5645_hweq_put" of the
ALSA binary control to avoid the user that puts the invalid parameters.
In the HWEQ enable function of speaker event, we also add the validating
function to prevent that the invalid parameters are applied to codec.
The HWEQ parameters should be controlled by DAPM for a specific sequence,
so the parameters will be applied to the codec in the speaker power up
event of DAPM, and will be disabled in the speaker power down event of
DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_codec_driver.set_pll is implemented to configure the FLL.
The codec internal SYSCLK can be from either the MCLK pin directly,
or the FLL. This is configured by snd_soc_codec_driver.set_pll.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want these to be zero or one, but by mistake we also accept negative
values. It's harmless but we should still clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Valid values for "deemph" are zero and one but we accidentally allow
negative values as well. It's harmless but it causes static checker
warnings and we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Valid values for "deemph" are zero and one, but we mistakenly allow
negative values as well. It's harmless but we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Valid values for "deemph" are zero and one, but we accidentally allow
negative values as well. It's harmless, but static checkers complain
and we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only accept "deemph" values of zero and one, but by mistake we
accept negatives as well. It's harmless but let's clean it up anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code tries to verify that "deemph" is zero or one, but it fails to
account for that it can be negative. It's harmless because negatives
are treated the same as one, but we should fix it just to silence the
static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We try to check that "deemph" is zero or one, but because of an
underflow bug, it can also be negative. It's fine, negative values are
handled as non-zero. But it's messy and static checkers complain so
let's fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By doing software reset of wm8962 in pm_resume, all registers which
have already been set will be reset to default value without regmap
interface be involved, thus driver need to mark cache_dirty flag,
to let regcache can be updated by regcache_sync().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The register value to enable gpio2 was incorrect. So fix it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The implementation of ssm2518_register_volatile always returns false,
this behavior is the same as no .volatile_reg callback implementation
when cache_type != REGCACHE_NONE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
adau193x_reg_volatile() always return false.
This seems pointless because current code uses REGCACHE_NONE cache_type
which is supposed to be volatile.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver also supports adau1328, thus add adau1328 to ad193x_spi_id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch rechecks the jack detect status after resuming from S3.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The index_cache is per instance run time state but rt298_index_def is not.
Make rt298_index_def const and make a copy of memory for index_cache rather
than directly use the rt298_index_def.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the default value on rt298_index_def are incorrect. Change
them to the correct value.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not necessary to set registers volatile. So, return false
for default case of rt298_volatile_register.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were getting build warning about "Section mismatch".
dmi_platform_intel_broadwell is being referenced from the probe function
rt5645_i2c_probe(), but dmi_platform_intel_broadwell was marked with
__initdata.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver now can make use of mclk data, if provided, to set, enable
and disable the clock source. As part of this, the choice to
enable clock squaring is dealt with as part of dai_sysclk() call
rather than as platform data.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
