There were some documentation locations that irda was mentioned, as well
as an old MAINTAINERS entry and the networking sysctl entries. Clean
these all out as this stuff really is finally gone.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 fixes from Thomas Gleixner:
"A set of fixes and updates for x86:
- Address a swiotlb regression which was caused by the recent DMA
rework and made driver fail because dma_direct_supported() returned
false
- Fix a signedness bug in the APIC ID validation which caused invalid
APIC IDs to be detected as valid thereby bloating the CPU possible
space.
- Fix inconsisten config dependcy/select magic for the MFD_CS5535
driver.
- Fix a corruption of the physical address space bits when encryption
has reduced the address space and late cpuinfo updates overwrite
the reduced bit information with the original value.
- Dominiks syscall rework which consolidates the architecture
specific syscall functions so all syscalls can be wrapped with the
same macros. This allows to switch x86/64 to struct pt_regs based
syscalls. Extend the clearing of user space controlled registers in
the entry patch to the lower registers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix signedness bug in APIC ID validity checks
x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
x86/olpc: Fix inconsistent MFD_CS5535 configuration
swiotlb: Use dma_direct_supported() for swiotlb_ops
syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
syscalls/core, syscalls/x86: Clean up syscall stub naming convention
syscalls/x86: Extend register clearing on syscall entry to lower registers
syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
x86/syscalls: Don't pointlessly reload the system call number
x86/mm: Fix documentation of module mapping range with 4-level paging
x86/cpuid: Switch to 'static const' specifier
Pull scheduler fixes from Thomas Gleixner:
"A few scheduler fixes:
- Prevent a bogus warning vs. runqueue clock update flags in
do_sched_rt_period_timer()
- Simplify the helper functions which handle requests for skipping
the runqueue clock updat.
- Do not unlock the tunables mutex in the error path of the cpu
frequency scheduler utils. Its not held.
- Enforce proper alignement for 'struct util_est' in sched_avg to
prevent a misalignment fault on IA64"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Force proper alignment of 'struct util_est'
sched/core: Simplify helpers for rq clock update skip requests
sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning
sched/cpufreq/schedutil: Fix error path mutex unlock
Pull more perf updates from Thomas Gleixner:
"A rather large set of perf updates:
Kernel:
- Fix various initialization issues
- Prevent creating [ku]probes for not CAP_SYS_ADMIN users
Tooling:
- Show only failing syscalls with 'perf trace --failure' (Arnaldo
Carvalho de Melo)
e.g: See what 'openat' syscalls are failing:
# perf trace --failure -e openat
762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory
<SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? >
790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory
^C#
- Show information about the event (freq, nr_samples, total
period/nr_events) in the annotate --tui and --stdio2 'perf
annotate' output, similar to the first line in the 'perf report
--tui', but just for the samples for a the annotated symbol
(Arnaldo Carvalho de Melo)
- Introduce 'perf version --build-options' to show what features were
linked, aliased as well as a shorter 'perf -vv' (Jin Yao)
- Add a "dso_size" sort order (Kim Phillips)
- Remove redundant ')' in the tracepoint output in 'perf trace'
(Changbin Du)
- Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo
Carvalho de Melo)
- Show group details on the title line in the annotate browser and
'perf annotate --stdio2' output, so that the per-event columns can
have headers (Arnaldo Carvalho de Melo)
- Fixup vertical line separating metrics from instructions and
cleaning unused lines at the bottom, both in the annotate TUI
browser (Arnaldo Carvalho de Melo)
- Remove duplicated 'samples' in lost samples warning in
'perf report' (Arnaldo Carvalho de Melo)
- Synchronize i915_drm.h, silencing the perf build process,
automagically adding support for the new DRM_I915_QUERY ioctl
(Arnaldo Carvalho de Melo)
- Make auxtrace_queues__add_buffer() allocate struct buffer, from a
patchkit already applied (Adrian Hunter)
- Fix the --stdio2/TUI annotate output to include group details, be
it for a recorded '{a,b,f}' explicit event group or when forcing
group display using 'perf report --group' for a set of events not
recorded as a group (Arnaldo Carvalho de Melo)
- Fix display artifacts in the ui browser (base class for the
annotate and main report/top TUI browser) related to the extra
title lines work (Arnaldo Carvalho de Melo)
- perf auxtrace refactorings, leftovers from a previously partially
processed patchset (Adrian Hunter)
- Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de
Melo)
- Synchronize i915_drm.h, silencing a perf build warning and in the
process automagically adding support for a new ioctl command
(Arnaldo Carvalho de Melo)
- Fix a strncpy issue in uprobe tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
tracing/uprobe_event: Fix strncpy corner case
perf/core: Fix perf_uprobe_init()
perf/core: Fix perf_kprobe_init()
perf/core: Fix use-after-free in uprobe_perf_close()
perf tests clang: Fix function name for clang IR test
perf clang: Add support for recent clang versions
perf tools: Fix perf builds with clang support
perf tools: No need to include namespaces.h in util.h
perf hists browser: Remove leftover from row returned from refresh
perf hists browser: Show extra_title_lines in the 'D' debug hotkey
perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering
tools headers uapi: Synchronize i915_drm.h
perf report: Remove duplicated 'samples' in lost samples warning
perf ui browser: Fixup cleaning unused lines at the bottom
perf annotate browser: Fixup vertical line separating metrics from instructions
perf annotate: Show group details on the title line
perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer
perf/x86/intel: Move regs->flags EXACT bit init
perf trace: Remove redundant ')'
...
Pull irq affinity fixes from Thomas Gleixner:
- Fix error path handling in the affinity spreading code
- Make affinity spreading smarter to avoid issues on systems which
claim to have hotpluggable CPUs while in fact they can't hotplug
anything.
So instead of trying to spread the vectors (and thereby the
associated device queues) to all possibe CPUs, spread them on all
present CPUs first. If there are left over vectors after that first
step they are spread among the possible, but not present CPUs which
keeps the code backwards compatible for virtual decives and NVME
which allocate a queue per possible CPU, but makes the spreading
smarter for devices which have less queues than possible or present
CPUs.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Spread irq vectors among present CPUs as far as possible
genirq/affinity: Allow irq spreading from a given starting point
genirq/affinity: Move actual irq vector spreading into a helper function
genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask
genirq/affinity: Don't return with empty affinity masks on error
For s390 new kernels are loaded to fixed addresses in memory before they
are booted. With the current code this is a problem as it assumes the
kernel will be loaded to an 'arbitrary' address. In particular,
kexec_locate_mem_hole searches for a large enough memory region and sets
the load address (kexec_bufer->mem) to it.
Luckily there is a simple workaround for this problem. By returning 1
in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off. This
allows the architecture to set kbuf->mem by hand. While the trick works
fine for the kernel it does not for the purgatory as here the
architectures don't have access to its kexec_buffer.
Give architectures access to the purgatories kexec_buffer by changing
kexec_load_purgatory to take a pointer to it. With this change
architectures have access to the buffer and can edit it as they need.
A nice side effect of this change is that we can get rid of the
purgatory_info->purgatory_load_address field. As now the information
stored there can directly be accessed from kbuf->mem.
Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code uses the sh_offset field in purgatory_info->sechdrs to
store a pointer to the current load address of the section. Depending
whether the section will be loaded or not this is either a pointer into
purgatory_info->purgatory_buf or kexec_purgatory. This is not only a
violation of the ELF standard but also makes the code very hard to
understand as you cannot tell if the memory you are using is read-only
or not.
Remove this misuse and store the offset of the section in
pugaroty_info->purgatory_buf in sh_offset.
Link: http://lkml.kernel.org/r/20180321112751.22196-10-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main loop currently uses quite a lot of variables to update the
section headers. Some of them are unnecessary. So clean them up a
little.
Link: http://lkml.kernel.org/r/20180321112751.22196-9-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To update the entry point there is an extra loop over all section
headers although this can be done in the main loop. So move it there
and eliminate the extra loop and variable to store the 'entry section
index'.
Also, in the main loop, move the usual case, i.e. non-bss section, out
of the extra if-block.
Link: http://lkml.kernel.org/r/20180321112751.22196-8-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When inspecting __kexec_load_purgatory you find that it has two tasks
1) setting up the kexec_buffer for the new kernel and,
2) setting up pi->sechdrs for the final load address.
The two tasks are independent of each other. To improve readability
split up __kexec_load_purgatory into two functions, one for each task,
and call them directly from kexec_load_purgatory.
Link: http://lkml.kernel.org/r/20180321112751.22196-7-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the relocations are applied to the purgatory only the section the
relocations are applied to is writable. The other sections, i.e. the
symtab and .rel/.rela, are in read-only kexec_purgatory. Highlight this
by marking the corresponding variables as 'const'.
While at it also change the signatures of arch_kexec_apply_relocations* to
take section pointers instead of just the index of the relocation section.
This removes the second lookup and sanity check of the sections in arch
code.
Link: http://lkml.kernel.org/r/20180321112751.22196-6-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The stripped purgatory does not contain a symtab. So when looking for
symbols this is done in read-only kexec_purgatory. Highlight this by
marking the corresponding variables as 'const'.
Link: http://lkml.kernel.org/r/20180321112751.22196-5-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kexec_purgatory buffer is read-only. Thus all pointers into
kexec_purgatory are read-only, too. Point this out by explicitly
marking purgatory_info->ehdr as 'const' and update the comments in
purgatory_info.
Link: http://lkml.kernel.org/r/20180321112751.22196-4-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before the purgatory is loaded several checks are done whether the ELF
file in kexec_purgatory is valid or not. These checks are incomplete.
For example they don't check for the total size of the sections defined
in the section header table or if the entry point actually points into
the purgatory.
On the other hand the purgatory, although an ELF file on its own, is
part of the kernel. Thus not trusting the purgatory means not trusting
the kernel build itself.
So remove all validity checks on the purgatory and just trust the kernel
build.
Link: http://lkml.kernel.org/r/20180321112751.22196-3-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the previous patches, commonly-used routines, exclude_mem_range() and
prepare_elf64_headers(), were carved out. Now place them in kexec
common code. A prefix "crash_" is given to each of their names to avoid
possible name collisions.
Link: http://lkml.kernel.org/r/20180306102303.9063-8-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As arch_kexec_kernel_image_{probe,load}(),
arch_kimage_file_post_load_cleanup() and arch_kexec_kernel_verify_sig()
are almost duplicated among architectures, they can be commonalized with
an architecture-defined kexec_file_ops array. So let's factor them out.
Link: http://lkml.kernel.org/r/20180306102303.9063-3-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kexec_file, x86, powerpc: refactoring for other
architecutres", v2.
This is a preparatory patchset for adding kexec_file support on arm64.
It was originally included in a arm64 patch set[1], but Philipp is also
working on their kexec_file support on s390[2] and some changes are now
conflicting.
So these common parts were extracted and put into a separate patch set
for better integration. What's more, my original patch#4 was split into
a few small chunks for easier review after Dave's comment.
As such, the resulting code is basically identical with my original, and
the only *visible* differences are:
- renaming of _kexec_kernel_image_probe() and _kimage_file_post_load_cleanup()
- change one of types of arguments at prepare_elf64_headers()
Those, unfortunately, require a couple of trivial changes on the rest
(#1, #6 to #13) of my arm64 kexec_file patch set[1].
Patch #1 allows making a use of purgatory optional, particularly useful
for arm64.
Patch #2 commonalizes arch_kexec_kernel_{image_probe, image_load,
verify_sig}() and arch_kimage_file_post_load_cleanup() across
architectures.
Patches #3-#7 are also intended to generalize parse_elf64_headers(),
along with exclude_mem_range(), to be made best re-use of.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-February/561182.html
[2] http://lkml.iu.edu//hypermail/linux/kernel/1802.1/02596.html
This patch (of 7):
On arm64, crash dump kernel's usable memory is protected by *unmapping*
it from kernel virtual space unlike other architectures where the region
is just made read-only. It is highly unlikely that the region is
accidentally corrupted and this observation rationalizes that digest
check code can also be dropped from purgatory. The resulting code is so
simple as it doesn't require a bit ugly re-linking/relocation stuff,
i.e. arch_kexec_apply_relocations_add().
Please see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2017-December/545428.html
All that the purgatory does is to shuffle arguments and jump into a new
kernel, while we still need to have some space for a hash value
(purgatory_sha256_digest) which is never checked against.
As such, it doesn't make sense to have trampline code between old kernel
and new kernel on arm64.
This patch introduces a new configuration, ARCH_HAS_KEXEC_PURGATORY, and
allows related code to be compiled in only if necessary.
[takahiro.akashi@linaro.org: fix trivial screwup]
Link: http://lkml.kernel.org/r/20180309093346.GF25863@linaro.org
Link: http://lkml.kernel.org/r/20180306102303.9063-2-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 6326fec112 ("mm: Use owner_priv bit for PageSwapCache,
valid when PageSwapBacked"), PG_swapcache is an alias for
PG_owner_priv_1, which may be also used for other purposes.
To know whether the bit indeed has the PG_swapcache meaning, it is
necessary to check PG_swapbacked, hence this bit must be exported.
Link: http://lkml.kernel.org/r/20180410161345.142e142d@ezekiel.suse.cz
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: "Marc-Andr Lureau" <marcandre.lureau@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've got a bug report indicating a kernel panic at booting on an x86-32
system, and it turned out to be the invalid PCI resource assigned after
reallocation. __find_resource() first aligns the resource start address
and resets the end address with start+size-1 accordingly, then checks
whether it's contained. Here the end address may overflow the integer,
although resource_contains() still returns true because the function
validates only start and end address. So this ends up with returning an
invalid resource (start > end).
There was already an attempt to cover such a problem in the commit
47ea91b405 ("Resource: fix wrong resource window calculation"), but
this case is an overseen one.
This patch adds the validity check of the newly calculated resource for
avoiding the integer overflow problem.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1086739
Link: http://lkml.kernel.org/r/s5hpo37d5l8.wl-tiwai@suse.de
Fixes: 23c570a674 ("resource: ability to resize an allocated resource")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Michael Henders <hendersm@shaw.ca>
Tested-by: Michael Henders <hendersm@shaw.ca>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Replace open coded "ARRAY_SIZE()" with macro
- Updates to uprobes
- Bug fix for perf event filter on error path
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCWs+2YxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qsRUAP9okqGRR/01bBLqNKiJ2j5YeBc9YlWl
R2rC0xbwVBLgJQEAwpE5jxahqKutbgrBDalDeCmXmeTOhSbGRJaBxXqwzwE=
=ZAuQ
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few clean ups and bug fixes:
- replace open coded "ARRAY_SIZE()" with macro
- updates to uprobes
- bug fix for perf event filter on error path"
* tag 'trace-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Enforce passing in filter=NULL to create_filter()
trace_uprobe: Simplify probes_seq_show()
trace_uprobe: Use %lx to display offset
tracing/uprobe: Add support for overlayfs
tracing: Use ARRAY_SIZE() macro instead of open coding it
* minor regression test cleanup
* formatting fixes for end user use of kdb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zz/y
-----END PGP SIGNATURE-----
Merge tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kdb updates from Jason Wessel:
- fix 2032 time access issues and new compiler warnings
- minor regression test cleanup
- formatting fixes for end user use of kdb
* tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: use memmove instead of overlapping memcpy
kdb: use ktime_get_mono_fast_ns() instead of ktime_get_ts()
kdb: bl: don't use tab character in output
kdb: drop newline in unknown command output
kdb: make "mdr" command repeat
kdb: use __ktime_get_real_seconds instead of __current_kernel_time
misc: kgdbts: Display progress of asynchronous tests
Non-root user cannot create kprobe or uprobe through the text-based
interface (kprobe_events, uprobe_events),so they should not be able
to create probes via perf_event_open() either.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Song Liu <songliubraving@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 33ea4b2427 ("perf/core: Implement the 'perf_uprobe' PMU")
Fixes: e12f03d703 ("perf/core: Implement the 'perf_kprobe' PMU")
Link: http://lkml.kernel.org/r/C0B2EFB5-C403-4BDB-9046-C14B3EE66999@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough. That
required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to
the cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation
from drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures
for shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers
a bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Pnk4
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These include one big-ticket item which is the rework of the idle loop
in order to prevent CPUs from spending too much time in shallow idle
states. It reduces idle power on some systems by 10% or more and may
improve performance of workloads in which the idle loop overhead
matters. This has been in the works for several weeks and it has been
tested and reviewed quite thoroughly.
Also included are changes that finalize the cpufreq cleanup moving
frequency table validation from drivers to the core, a few fixes and
cleanups of cpufreq drivers, a cpuidle documentation update and a PM
QoS core update to mark the expected switch fall-throughs in it.
Specifics:
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough.
That required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to the
cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation from
drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures for
shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers a
bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva)"
* tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
tick-sched: avoid a maybe-uninitialized warning
cpufreq: Drop cpufreq_table_validate_and_show()
cpufreq: SCMI: Don't validate the frequency table twice
cpufreq: CPPC: Initialize shared perf capabilities of CPUs
cpufreq: armada-37xx: Fix clock leak
cpufreq: CPPC: Don't set transition_latency
cpufreq: ti-cpufreq: Use builtin_platform_driver()
cpufreq: intel_pstate: Do not include debugfs.h
PM / QoS: mark expected switch fall-throughs
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
...
This results in no change in structure size on 64-bit machines as it
fits in the padding between the gfp_t and the void *. 32-bit machines
will grow the structure from 8 to 12 bytes. Almost all radix trees are
protected with (at least) a spinlock, so as they are converted from
radix trees to xarrays, the data structures will shrink again.
Initialising the spinlock requires a name for the benefit of lockdep, so
RADIX_TREE_INIT() now needs to know the name of the radix tree it's
initialising, and so do IDR_INIT() and IDA_INIT().
Also add the xa_lock() and xa_unlock() family of wrappers to make it
easier to use the lock. If we could rely on -fplan9-extensions in the
compiler, we could avoid all of this syntactic sugar, but that wasn't
added until gcc 4.6.
Link: http://lkml.kernel.org/r/20180313132639.17387-8-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kdoc comments are added to the do_proc_dointvec_minmax_conv_param and
do_proc_douintvec_minmax_conv_param structures thare are used internally
for range checking.
The error codes returned by proc_dointvec_minmax() and
proc_douintvec_minmax() are also documented.
Link: http://lkml.kernel.org/r/1519926220-7453-3-git-send-email-longman@redhat.com
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As using an unsafe module parameter is, by its very definition, an
expected user action, emitting a warning is overkill. Nothing has yet
gone wrong, and we add a taint flag for any future oops should something
actually go wrong. So instead of having a user controllable pr_warn,
downgrade it to a pr_notice for "a normal, but significant condition".
We make use of unsafe kernel parameters in igt
(https://cgit.freedesktop.org/drm/igt-gpu-tools/) (we have not yet
succeeded in removing all such debugging options), which generates a
warning and taints the kernel. The warning is unhelpful as we then need
to filter it out again as we check that every test themselves do not
provoke any kernel warnings.
Link: http://lkml.kernel.org/r/20180226151919.9674-1-chris@chris-wilson.co.uk
Fixes: 91f9d330cc ("module: make it possible to have unsafe, tainting module params")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Petri Latvala <petri.latvala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix sizeof argument to be the same as the data variable name. Probably
a copy/paste error.
Mostly harmless since both variables are unsigned int.
Fixes kernel bugzilla #197371:
Possible access to unintended variable in "kernel/sysctl.c" line 1339
https://bugzilla.kernel.org/show_bug.cgi?id=197371
Link: http://lkml.kernel.org/r/e0d0531f-361e-ef5f-8499-32743ba907e1@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Petru Mihancea <petrum@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So "struct uts_namespace" can enjoy fine-grained SLAB debugging and
usercopy protection.
I'd prefer shorter name "utsns" but there is "user_namespace" already.
Link: http://lkml.kernel.org/r/20180228215158.GA23146@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the randstruct plugin can intentionally produce extremely unusual
kernel structure layouts (even performance pathological ones), some
maintainers want to be able to trivially determine if an Oops is coming
from a randstruct-built kernel, so as to keep their sanity when
debugging. This adds the new flag and initializes taint_mask
immediately when built with randstruct.
Link: http://lkml.kernel.org/r/1519084390-43867-4-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This consolidates the taint bit documentation into a single place with
both numeric and letter values. Additionally adds the missing TAINT_AUX
documentation.
Link: http://lkml.kernel.org/r/1519084390-43867-3-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This converts to using indexed initializers instead of comments, adds a
comment on why the taint flags can't be an enum, and make sure that no
one forgets to update the taint_flags when adding new bits.
Link: http://lkml.kernel.org/r/1519084390-43867-2-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's some inconsistency with what to set the output parameter filterp
when passing to create_filter(..., struct event_filter **filterp).
Whatever filterp points to, should be NULL when calling this function. The
create_filter() calls create_filter_start() with a pointer to a local
"filter" variable that is set to NULL. The create_filter_start() has a
WARN_ON() if the passed in pointer isn't pointing to a value set to NULL.
Ideally, create_filter() should pass the filterp variable it received to
create_filter_start() and not hide it as with a local variable, this allowed
create_filter() to fail, and not update the passed in filter, and the caller
of create_filter() then tried to free filter, which was never initialized to
anything, causing memory corruption.
Link: http://lkml.kernel.org/r/00000000000032a0c30569916870@google.com
Fixes: 80765597bc ("tracing: Rewrite filter logic to be simpler and faster")
Reported-by: syzbot+dadcc936587643d7f568@syzkaller.appspotmail.com
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Simplify probes_seq_show() function. No change in output
before and after patch.
Link: http://lkml.kernel.org/r/20180315082756.9050-2-ravi.bangoria@linux.vnet.ibm.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
tu->offset is unsigned long, not a pointer, thus %lx should
be used to print it, not the %px.
Link: http://lkml.kernel.org/r/20180315082756.9050-1-ravi.bangoria@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 0e4d819d08 ("trace_uprobe: Display correct offset in uprobe_events")
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
uprobes cannot successfully attach to binaries located in a directory
mounted with overlayfs.
To verify, create directories for mounting overlayfs
(upper,lower,work,merge), move some binary into merge/ and use readelf
to obtain some known instruction of the binary. I used /bin/true and the
entry instruction(0x13b0):
$ mount -t overlay overlay -o lowerdir=lower,upperdir=upper,workdir=work merge
$ cd /sys/kernel/debug/tracing
$ echo 'p:true_entry PATH_TO_MERGE/merge/true:0x13b0' > uprobe_events
$ echo 1 > events/uprobes/true_entry/enable
This returns 'bash: echo: write error: Input/output error' and dmesg
tells us 'event trace: Could not enable event true_entry'
This change makes create_trace_uprobe() look for the real inode of a
dentry. In the case of normal filesystems, this simplifies to just
returning the inode. In the case of overlayfs(and similar fs) we will
obtain the underlying dentry and corresponding inode, upon which uprobes
can successfully register.
Running the example above with the patch applied, we can see that the
uprobe is enabled and will output to trace as expected.
Link: http://lkml.kernel.org/r/20180410231030.2720-1-hmclauchlan@fb.com
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Howard McLauchlan <hmclauchlan@fb.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
It is useless to re-invent the ARRAY_SIZE macro so let's use it instead
of DATA_CNT.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Link: http://lkml.kernel.org/r/20171016012250.26453-1-jeremy.lefaure@lse.epita.fr
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
[ Removed useless include of kernel.h ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
* pm-cpuidle:
tick-sched: avoid a maybe-uninitialized warning
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
sched: idle: Do not stop the tick before cpuidle_idle_call()
sched: idle: Do not stop the tick upfront in the idle loop
time: tick-sched: Reorganize idle tick management code
* pm-qos:
PM / QoS: mark expected switch fall-throughs
syzbot reported a possible deadlock in perf_event_detach_bpf_prog.
The error details:
======================================================
WARNING: possible circular locking dependency detected
4.16.0-rc7+ #3 Not tainted
------------------------------------------------------
syz-executor7/24531 is trying to acquire lock:
(bpf_event_mutex){+.+.}, at: [<000000008a849b07>] perf_event_detach_bpf_prog+0x92/0x3d0 kernel/trace/bpf_trace.c:854
but task is already holding lock:
(&mm->mmap_sem){++++}, at: [<0000000038768f87>] vm_mmap_pgoff+0x198/0x280 mm/util.c:353
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&mm->mmap_sem){++++}:
__might_fault+0x13a/0x1d0 mm/memory.c:4571
_copy_to_user+0x2c/0xc0 lib/usercopy.c:25
copy_to_user include/linux/uaccess.h:155 [inline]
bpf_prog_array_copy_info+0xf2/0x1c0 kernel/bpf/core.c:1694
perf_event_query_prog_array+0x1c7/0x2c0 kernel/trace/bpf_trace.c:891
_perf_ioctl kernel/events/core.c:4750 [inline]
perf_ioctl+0x3e1/0x1480 kernel/events/core.c:4770
vfs_ioctl fs/ioctl.c:46 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:686
SYSC_ioctl fs/ioctl.c:701 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:692
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
-> #0 (bpf_event_mutex){+.+.}:
lock_acquire+0x1d5/0x580 kernel/locking/lockdep.c:3920
__mutex_lock_common kernel/locking/mutex.c:756 [inline]
__mutex_lock+0x16f/0x1a80 kernel/locking/mutex.c:893
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:908
perf_event_detach_bpf_prog+0x92/0x3d0 kernel/trace/bpf_trace.c:854
perf_event_free_bpf_prog kernel/events/core.c:8147 [inline]
_free_event+0xbdb/0x10f0 kernel/events/core.c:4116
put_event+0x24/0x30 kernel/events/core.c:4204
perf_mmap_close+0x60d/0x1010 kernel/events/core.c:5172
remove_vma+0xb4/0x1b0 mm/mmap.c:172
remove_vma_list mm/mmap.c:2490 [inline]
do_munmap+0x82a/0xdf0 mm/mmap.c:2731
mmap_region+0x59e/0x15a0 mm/mmap.c:1646
do_mmap+0x6c0/0xe00 mm/mmap.c:1483
do_mmap_pgoff include/linux/mm.h:2223 [inline]
vm_mmap_pgoff+0x1de/0x280 mm/util.c:355
SYSC_mmap_pgoff mm/mmap.c:1533 [inline]
SyS_mmap_pgoff+0x462/0x5f0 mm/mmap.c:1491
SYSC_mmap arch/x86/kernel/sys_x86_64.c:100 [inline]
SyS_mmap+0x16/0x20 arch/x86/kernel/sys_x86_64.c:91
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&mm->mmap_sem);
lock(bpf_event_mutex);
lock(&mm->mmap_sem);
lock(bpf_event_mutex);
*** DEADLOCK ***
======================================================
The bug is introduced by Commit f371b304f1 ("bpf/tracing: allow
user space to query prog array on the same tp") where copy_to_user,
which requires mm->mmap_sem, is called inside bpf_event_mutex lock.
At the same time, during perf_event file descriptor close,
mm->mmap_sem is held first and then subsequent
perf_event_detach_bpf_prog needs bpf_event_mutex lock.
Such a senario caused a deadlock.
As suggested by Daniel, moving copy_to_user out of the
bpf_event_mutex lock should fix the problem.
Fixes: f371b304f1 ("bpf/tracing: allow user space to query prog array on the same tp")
Reported-by: syzbot+dc5ca0e4c9bfafaf2bae@syzkaller.appspotmail.com
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
- Tom Zanussi's extended histogram work
This adds the synthetic events to have histograms from multiple event data
Adds triggers "onmatch" and "onmax" to call the synthetic events
Several updates to the histogram code from this
- Allow way to nest ring buffer calls in the same context
- Allow absolute time stamps in ring buffer
- Rewrite of filter code parsing based on Al Viro's suggestions
- Setting of trace_clock to global if TSC is unstable (on boot)
- Better OOM handling when allocating large ring buffers
- Added initcall tracepoints (consolidated initcall_debug code with them)
And other various fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iQHIBAABCgAyFiEEPm6V/WuN2kyArTUe1a05Y9njSUkFAlrLoCAUHHJvc3RlZHRA
Z29vZG1pcy5vcmcACgkQ1a05Y9njSUks/QwAn/ky8WgfjcRdjKmBYuEwDedvm9iI
V9G5kpv5JMw5dLz4l1pS3tA3M9Lyuc5z3Shw92FTy36vdU1wxEjQgHa7viB1xk9x
KsiTyNjTsgrRd7GVHMy/8Be2RRiTRLaXKAsLCoj/c7QWzagV1P8XWlWK5mojYkh/
DrSXyg9Avkp30+sU1bvcLWnmmZUFqMxs+bWipD9uFc98USMMyeP25nrnhrj0gDTg
Q93cjXUuyVRC4lJ2YTW0GCSKhMKEw5f/ltEOT1hwScqYkCJj1EubKqS53R/9h21z
IPUrYcqLnMRu0j2ejR+UAy5Vsy3gJUrPMQb0F6hlu1DwbMd0d/9SGh1c+Sm+zorh
yftWTdCZsYrXkaOuB6V5M30X+KBwbWO0Xc9VCvgJ/IU5vMlgLSt5itTWbT/Fmfhb
ll5/RXP7zhSXRv5sdl/BP3/4dd6F8jpyKyaR2Rk2+XjBOGIq5mvqNGr4Vj9AzxW8
E0nvq7l7e0dbxZNM42gEm3cht1VUg7Zz0Y0+
=91oN
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"New features:
- Tom Zanussi's extended histogram work.
This adds the synthetic events to have histograms from multiple
event data Adds triggers "onmatch" and "onmax" to call the
synthetic events Several updates to the histogram code from this
- Allow way to nest ring buffer calls in the same context
- Allow absolute time stamps in ring buffer
- Rewrite of filter code parsing based on Al Viro's suggestions
- Setting of trace_clock to global if TSC is unstable (on boot)
- Better OOM handling when allocating large ring buffers
- Added initcall tracepoints (consolidated initcall_debug code with
them)
And other various fixes and clean ups"
* tag 'trace-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (68 commits)
init: Have initcall_debug still work without CONFIG_TRACEPOINTS
init, tracing: Have printk come through the trace events for initcall_debug
init, tracing: instrument security and console initcall trace events
init, tracing: Add initcall trace events
tracing: Add rcu dereference annotation for test func that touches filter->prog
tracing: Add rcu dereference annotation for filter->prog
tracing: Fixup logic inversion on setting trace_global_clock defaults
tracing: Hide global trace clock from lockdep
ring-buffer: Add set/clear_current_oom_origin() during allocations
ring-buffer: Check if memory is available before allocation
lockdep: Add print_irqtrace_events() to __warn
vsprintf: Do not preprocess non-dereferenced pointers for bprintf (%px and %pK)
tracing: Uninitialized variable in create_tracing_map_fields()
tracing: Make sure variable string fields are NULL-terminated
tracing: Add action comparisons when testing matching hist triggers
tracing: Don't add flag strings when displaying variable references
tracing: Fix display of hist trigger expressions containing timestamps
ftrace: Drop a VLA in module_exists()
tracing: Mention trace_clock=global when warning about unstable clocks
tracing: Default to using trace_global_clock if sched_clock is unstable
...
Fix string fetch function to terminate with NUL.
It is OK to drop the rest of string.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org
Cc: 范龙飞 <long7573@126.com>
Fixes: 5baaa59ef0 ("tracing/probes: Implement 'memory' fetch method for uprobes")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The use of bitfields seems to confuse gcc, leading to a false-positive
warning in all compiler versions:
kernel/time/tick-sched.c: In function 'tick_nohz_idle_exit':
kernel/time/tick-sched.c:538:2: error: 'now' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This introduces a temporary variable to track the flags so gcc
doesn't have to evaluate twice, eliminating the code path that
leads to the warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=85301
Fixes: 1cae544d42d2 ("nohz: Gather tick_sched booleans under a common flag field")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Similarly to the uprobe PMU fix in perf_kprobe_init(), fix error
handling in perf_uprobe_init() as well.
Reported-by: 范龙飞 <long7573@126.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: e12f03d703 ("perf/core: Implement the 'perf_kprobe' PMU")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
1) The sockmap code has to free socket memory on close if there is
corked data, from John Fastabend.
2) Tunnel names coming from userspace need to be length validated. From
Eric Dumazet.
3) arp_filter() has to take VRFs properly into account, from Miguel
Fadon Perlines.
4) Fix oops in error path of tcf_bpf_init(), from Davide Caratti.
5) Missing idr_remove() in u32_delete_key(), from Cong Wang.
6) More syzbot stuff. Several use of uninitialized value fixes all
over, from Eric Dumazet.
7) Do not leak kernel memory to userspace in sctp, also from Eric
Dumazet.
8) Discard frames from unused ports in DSA, from Andrew Lunn.
9) Fix DMA mapping and reset/failover problems in ibmvnic, from Thomas
Falcon.
10) Do not access dp83640 PHY registers prematurely after reset, from
Esben Haabendal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vhost-net: set packet weight of tx polling to 2 * vq size
net: thunderx: rework mac addresses list to u64 array
inetpeer: fix uninit-value in inet_getpeer
dp83640: Ensure against premature access to PHY registers after reset
devlink: convert occ_get op to separate registration
ARM: dts: ls1021a: Specify TBIPA register address
net/fsl_pq_mdio: Allow explicit speficition of TBIPA address
ibmvnic: Do not reset CRQ for Mobility driver resets
ibmvnic: Fix failover case for non-redundant configuration
ibmvnic: Fix reset scheduler error handling
ibmvnic: Zero used TX descriptor counter on reset
ibmvnic: Fix DMA mapping mistakes
tipc: use the right skb in tipc_sk_fill_sock_diag()
sctp: sctp_sockaddr_af must check minimal addr length for AF_INET6
net: dsa: Discard frames from unused ports
sctp: do not leak kernel memory to user space
soreuseport: initialise timewait reuseport field
ipv4: fix uninit-value in ip_route_output_key_hash_rcu()
dccp: initialize ireq->ir_mark
net: fix uninit-value in __hw_addr_add_ex()
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use timerqueue_iterate_next() to get to the next timer in
__hrtimer_next_event_base() without browsing the timerqueue
details diredctly.
No intentional changes in functionality.
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move the code setting ts->got_idle_tick into tick_sched_do_timer() to
avoid code duplication.
No intentional changes in functionality.
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Optimize the space and leave plenty of room for further flags.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
[ rjw: Do not use __this_cpu_read() to access tick_stopped and add
got_idle_tick to avoid overloading inidle ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the tick isn't stopped, the target residency of the state selected
by the menu governor may be greater than the actual time to the next
tick and that means lost energy.
To avoid that, make tick_nohz_get_sleep_length() return the current
time to the next event (before stopping the tick) in addition to the
estimated one via an extra pointer argument and make menu_select()
use that value to refine the state selection when necessary.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
In order to address the issue with short idle duration predictions
by the idle governor after the scheduler tick has been stopped,
reorder the code in cpuidle_idle_call() so that the governor idle
state selection runs before tick_nohz_idle_go_idle() and use the
"nohz" hint returned by cpuidle_select() to decide whether or not
to stop the tick.
This isn't straightforward, because menu_select() invokes
tick_nohz_get_sleep_length() to get the time to the next timer
event and the number returned by the latter comes from
__tick_nohz_idle_stop_tick(). Fortunately, however, it is possible
to compute that number without actually stopping the tick and with
the help of the existing code.
Namely, tick_nohz_get_sleep_length() can be made call
tick_nohz_next_event(), introduced earlier, to get the time to the
next non-highres timer event. If that happens, tick_nohz_next_event()
need not be called by __tick_nohz_idle_stop_tick() again.
If it turns out that the scheduler tick cannot be stopped going
forward or the next timer event is too close for the tick to be
stopped, tick_nohz_get_sleep_length() can simply return the time to
the next event currently programmed into the corresponding clock
event device.
In addition to knowing the return value of tick_nohz_next_event(),
however, tick_nohz_get_sleep_length() needs to know the time to the
next highres timer event, but with the scheduler tick timer excluded,
which can be computed with the help of hrtimer_get_next_event().
That minimum of that number and the tick_nohz_next_event() return
value is the total time to the next timer event with the assumption
that the tick will be stopped. It can be returned to the idle
governor which can use it for predicting idle duration (under the
assumption that the tick will be stopped) and deciding whether or
not it makes sense to stop the tick before putting the CPU into the
selected idle state.
With the above, the sleep_length field in struct tick_sched is not
necessary any more, so drop it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199227
Reported-by: Doug Smythies <dsmythies@telus.net>
Reported-by: Thomas Ilsche <thomas.ilsche@tu-dresden.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-04-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two sockmap fixes: i) fix a potential warning when a socket with
pending cork data is closed by freeing the memory right when the
socket is closed instead of seeing still outstanding memory at
garbage collector time, ii) fix a NULL pointer deref in case of
duplicates release calls, so make sure to only reset the sk_prot
pointer when it's in a valid state to do so, both from John.
2) Fix a compilation warning in bpf_prog_attach_check_attach_type()
by moving the function under CONFIG_CGROUP_BPF ifdef since only
used there, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull general security layer updates from James Morris:
- Convert security hooks from list to hlist, a nice cleanup, saving
about 50% of space, from Sargun Dhillon.
- Only pass the cred, not the secid, to kill_pid_info_as_cred and
security_task_kill (as the secid can be determined from the cred),
from Stephen Smalley.
- Close a potential race in kernel_read_file(), by making the file
unwritable before calling the LSM check (vs after), from Kees Cook.
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: convert security hooks to use hlist
exec: Set file unwritable before LSM check
usb, signal, security: only pass the cred, not the secid, to kill_pid_info_as_cred and security_task_kill
The next set of changes will need to compute the time to the next
hrtimer event over all hrtimers except for the scheduler tick one.
To that end introduce a new helper function,
hrtimer_next_event_without(), for computing the time until the next
hrtimer event over all timers except for one and modify the underlying
code in __hrtimer_next_event_base() to prepare it for being called by
that new function.
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
In order to address the issue with short idle duration predictions
by the idle governor after the scheduler tick has been stopped, split
tick_nohz_stop_sched_tick() into two separate routines, one computing
the time to the next timer event and the other simply stopping the
tick when the time to the next timer event is known.
Prepare these two routines to be called separately, as one of them
will be called by the idle governor in the cpuidle_select() code
path after subsequent changes.
Update the former callers of tick_nohz_stop_sched_tick() to use
the new routines, tick_nohz_next_event() and tick_nohz_stop_tick(),
instead of it and move the updates of the sleep_length field in
struct tick_sched into __tick_nohz_idle_stop_tick() as it doesn't
need to be updated anywhere else.
There should be no intentional visible changes in functionality
resulting from this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
This cleans up the qemu fw cfg device driver.
On top of this, vmcore is dumped there on crash to
help debugging witH kASLR enabled.
Also included are some fixes in vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaxYDNAAoJECgfDbjSjVRpHA8IAKrzyI2rB5KCn5Obo/SwgO9k
7z6FBw+QMWXUwnJGBjt7OFber3LIah0oLh39puohrKFo/OkjSZWSqBWZp5I43lHb
sijflF2QuZxWJvCg9GQswhVSmpouwKgFI3mQYqrX+T/MQxeozT0eAdc0TIX4OOYq
3gUtpgw9VZ1FEKKHgHv2ZWsiiN3QwVqSrR2QzS3hE+FZl8I1ElTRxq0evsb+d80U
Ybqbq3QcmAQms6isQyqqmAphOvi7JlHDQAWfsXQByY48cPc+oXkG6iS+jbSFJ2Fg
/YStUDmyMRxvAxdEVH8ZytigbdzAl8kAOhWKhhH/j4/nlHpT/udLm+MqIEAacYQ=
=PGTs
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull fw_cfg, vhost updates from Michael Tsirkin:
"This cleans up the qemu fw cfg device driver.
On top of this, vmcore is dumped there on crash to help debugging
with kASLR enabled.
Also included are some fixes in vhost"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: add vsock compat ioctl
vhost: fix vhost ioctl signature to build with clang
fw_cfg: write vmcoreinfo details
crash: export paddr_vmcoreinfo_note()
fw_cfg: add DMA register
fw_cfg: add a public uapi header
fw_cfg: handle fw_cfg_read_blob() error
fw_cfg: remove inline from fw_cfg_read_blob()
fw_cfg: fix sparse warnings around FW_CFG_FILE_DIR read
fw_cfg: fix sparse warning reading FW_CFG_ID
fw_cfg: fix sparse warnings with fw_cfg_file
fw_cfg: fix sparse warnings in fw_cfg_sel_endianness()
ptr_ring: fix build
-----BEGIN PGP SIGNATURE-----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=n1dk
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"We didn't have anything to send for v4.16, but we're back with a
little more than usual for v4.17.
Eleven patches in total, most fall into the small fix category, but
there are three non-trivial changes worth calling out:
- the audit entry filter is being removed after deprecating it for
quite a while (years of no one really using it because it turns out
to be not very practical)
- created our own version of "__mutex_owner()" because the locking
folks were upset we were using theirs
- improved our handling of kernel command line parameters to make
them more forgiving
- we fixed auditing of symlink operations
Everything passes the audit-testsuite and as of a few minutes ago it
merges well with your tree"
* tag 'audit-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: add refused symlink to audit_names
audit: remove path param from link denied function
audit: link denied should not directly generate PATH record
audit: make ANOM_LINK obey audit_enabled and audit_dummy_context
audit: do not panic on invalid boot parameter
audit: track the owner of the command mutex ourselves
audit: return on memory error to avoid null pointer dereference
audit: bail before bug check if audit disabled
audit: deprecate the AUDIT_FILTER_ENTRY filter
audit: session ID should not set arch quick field pointer
audit: update bugtracker and source URIs
Merge updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- the v9fs maintainers have been missing for a long time. I've taken
over v9fs patch slinging.
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (116 commits)
mm,oom_reaper: check for MMF_OOM_SKIP before complaining
mm/ksm: fix interaction with THP
mm/memblock.c: cast constant ULLONG_MAX to phys_addr_t
headers: untangle kmemleak.h from mm.h
include/linux/mmdebug.h: make VM_WARN* non-rvals
mm/page_isolation.c: make start_isolate_page_range() fail if already isolated
mm: change return type to vm_fault_t
mm, oom: remove 3% bonus for CAP_SYS_ADMIN processes
mm, page_alloc: wakeup kcompactd even if kswapd cannot free more memory
kernel/fork.c: detect early free of a live mm
mm: make counting of list_lru_one::nr_items lockless
mm/swap_state.c: make bool enable_vma_readahead and swap_vma_readahead() static
block_invalidatepage(): only release page if the full page was invalidated
mm: kernel-doc: add missing parameter descriptions
mm/swap.c: remove @cold parameter description for release_pages()
mm/nommu: remove description of alloc_vm_area
zram: drop max_zpage_size and use zs_huge_class_size()
zsmalloc: introduce zs_huge_class_size()
mm: fix races between swapoff and flush dcache
fs/direct-io.c: minor cleanups in do_blockdev_direct_IO
...
Trace events have been added around the initcall functions defined in
init/main.c. But console and security have their own initcalls. This adds
the trace events associated for those initcall functions.
Link: http://lkml.kernel.org/r/1521765208.19745.2.camel@polymtl.ca
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Abderrahmane Benbachir <abderrahmane.benbachir@polymtl.ca>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
A boot up test function update_pred_fn() dereferences filter->prog without
the proper rcu annotation.
To do this, we must also take the event_mutex first. Normally, this isn't
needed because this test function can not race with other use cases that
touch the event filters (it is disabled if any events are enabled).
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 80765597bc ("tracing: Rewrite filter logic to be simpler and faster")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
ftrace_function_set_filter() referenences filter->prog without annotation
and sparse complains about it. It needs a rcu_dereference_protected()
wrapper.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 80765597bc ("tracing: Rewrite filter logic to be simpler and faster")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In commit 932066a15335 ("tracing: Default to using trace_global_clock if
sched_clock is unstable"), the logic for deciding to override the
default clock if unstable was reversed from the earlier posting. I was
trying to reduce the width of the message by using an early return
rather than a if-block, but reverted back to using the if-block and
accidentally left the predicate inverted.
Link: http://lkml.kernel.org/r/20180404212450.26646-1-chris@chris-wilson.co.uk
Fixes: 932066a15335 ("tracing: Default to using trace_global_clock if sched_clock is unstable")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Function tracing can trace in NMIs and such. If the TSC is determined
to be unstable, the tracing clock will switch to the global clock on
boot up, unless "trace_clock" is specified on the kernel command line.
The global clock disables interrupts to access sched_clock_cpu(), and in
doing so can be done within lockdep internals (because of function
tracing and NMIs). This can trigger false lockdep splats.
The trace_clock_global() is special, best not to trace the irq logic
within it.
Link: http://lkml.kernel.org/r/20180404145015.77bde42d@gandalf.local.home
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As si_mem_available() can say there is enough memory even though the memory
available is not useable by the ring buffer, it is best to not kill innocent
applications because the ring buffer is taking up all the memory while it is
trying to allocate a great deal of memory.
If the allocator is user space (because kernel threads can also increase the
size of the kernel ring buffer on boot up), then after si_mem_available()
says there is enough memory, set the OOM killer to kill the current task if
an OOM triggers during the allocation.
Link: http://lkml.kernel.org/r/20180404062340.GD6312@dhcp22.suse.cz
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The ring buffer is made up of a link list of pages. When making the ring
buffer bigger, it will allocate all the pages it needs before adding to the
ring buffer, and if it fails, it frees them and returns an error. This makes
increasing the ring buffer size an all or nothing action. When this was
first created, the pages were allocated with "NORETRY". This was to not
cause any Out-Of-Memory (OOM) actions from allocating the ring buffer. But
NORETRY was too strict, as the ring buffer would fail to expand even when
there's memory available, but was taken up in the page cache.
Commit 848618857d ("tracing/ring_buffer: Try harder to allocate") changed
the allocating from NORETRY to RETRY_MAYFAIL. The RETRY_MAYFAIL would
allocate from the page cache, but if there was no memory available, it would
simple fail the allocation and not trigger an OOM.
This worked fine, but had one problem. As the ring buffer would allocate one
page at a time, it could take up all memory in the system before it failed
to allocate and free that memory. If the allocation is happening and the
ring buffer allocates all memory and then tries to take more than available,
its allocation will not trigger an OOM, but if there's any allocation that
happens someplace else, that could trigger an OOM, even though once the ring
buffer's allocation fails, it would free up all the previous memory it tried
to allocate, and allow other memory allocations to succeed.
Commit d02bd27bd3 ("mm/page_alloc.c: calculate 'available' memory in a
separate function") separated out si_mem_availble() as a separate function
that could be used to see how much memory is available in the system. Using
this function to make sure that the ring buffer could be allocated before it
tries to allocate pages we can avoid allocating all memory in the system and
making it vulnerable to OOMs if other allocations are taking place.
Link: http://lkml.kernel.org/r/1522320104-6573-1-git-send-email-zhaoyang.huang@spreadtrum.com
CC: stable@vger.kernel.org
Cc: linux-mm@kvack.org
Fixes: 848618857d ("tracing/ring_buffer: Try harder to allocate")
Requires: d02bd27bd3 ("mm/page_alloc.c: calculate 'available' memory in a separate function")
Reported-by: Zhaoyang Huang <huangzhaoyang@gmail.com>
Tested-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Running a test on a x86_32 kernel I triggered a bug that an interrupt
disable/enable isn't being catched by lockdep. At least knowing where the
last one was found would be helpful, but the warnings that are produced do
not show this information. Even without debugging lockdep, having the WARN()
display the last place hard and soft irqs were enabled or disabled is
valuable.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Smatch complains that idx can be used uninitialized when we check if
(idx < 0). It has to be the first iteration through the loop and the
HIST_FIELD_FL_STACKTRACE bit has to be clear and the HIST_FIELD_FL_VAR
bit has to be set to reach the bug.
Link: http://lkml.kernel.org/r/20180328114815.GC29050@mwanda
Fixes: 30350d65ac ("tracing: Add variable support to hist triggers")
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The strncpy() currently being used for variable string fields can
result in a lack of termination if the string length is equal to the
field size. Use the safer strscpy() instead, which will guarantee
termination.
Link: http://lkml.kernel.org/r/fb97c1e518fb358c12a4057d7445ba2c46956cd7.1522256721.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Actions also need to be considered when checking for matching triggers
- triggers differing only by action should be allowed, but currently
aren't because the matching check ignores the action and erroneously
returns -EEXIST.
Add and call an actions_match() function to address that.
Here's an example using onmatch() actions. The first -EEXIST shouldn't
occur because the onmatch() is different in the second wakeup_latency()
param. The second -EEXIST shouldn't occur because it's a different
action (in this case, it doesn't have an action, so shouldn't be seen
as being the same and therefore rejected).
In the after case, both are correctly accepted (and trying to add one of
them again returns -EEXIST as it should).
before:
# echo 'wakeup_latency u64 lat; pid_t pid' >> /sys/kernel/debug/tracing/synthetic_events
# echo 'hist:keys=pid:ts0=common_timestamp.usecs if comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
# echo 'hist:keys=next_pid:wakeup_lat=common_timestamp.usecs-$ts0 if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
# echo 'hist:keys=next_pid:onmatch(sched.sched_wakeup).wakeup_latency(sched.sched_switch.$wakeup_lat,next_pid) if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
# echo 'hist:keys=next_pid:onmatch(sched.sched_wakeup).wakeup_latency(sched.sched_switch.$wakeup_lat,prev_pid) if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
-su: echo: write error: File exists
# echo 'hist:keys=next_pid if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
-su: echo: write error: File exists
after:
# echo 'wakeup_latency u64 lat; pid_t pid' >> /sys/kernel/debug/tracing/synthetic_events
# echo 'hist:keys=pid:ts0=common_timestamp.usecs if comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
# echo 'hist:keys=next_pid:wakeup_lat=common_timestamp.usecs-$ts0 if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
# echo 'hist:keys=next_pid:onmatch(sched.sched_wakeup).wakeup_latency(sched.sched_switch.$wakeup_lat,next_pid) if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
# echo 'hist:keys=next_pid:onmatch(sched.sched_wakeup).wakeup_latency(sched.sched_switch.$wakeup_lat,prev_pid) if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
# echo 'hist:keys=next_pid if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
Link: http://lkml.kernel.org/r/a7fd668b87ec10736c8f016ac4279c8480d50c2b.1522256721.git.tom.zanussi@linux.intel.com
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Variable references should never have flags appended when displayed -
prevent that from happening.
Before:
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
hist:keys=next_pid:vals=hitcount:wakeup_lat=common_timestamp.usecs-$ts0.usecs:...
After:
hist:keys=next_pid:vals=hitcount:wakeup_lat=common_timestamp.usecs-$ts0:...
Link: http://lkml.kernel.org/r/913318a5610ef6b24af2522575f671fa6ee19b6b.1522256721.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When displaying hist triggers, variable references that have the
timestamp field flag set are erroneously displayed as common_timestamp
rather than the variable reference. Additionally, timestamp
expressions are displayed in the same way. Fix this by forcing the
timestamp flag handling to follow variable reference and expression
handling.
Before:
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
hist:keys=next_pid:vals=hitcount:wakeup_lat=common_timestamp.usecs:...
After:
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
hist:keys=next_pid:vals=hitcount:wakeup_lat=common_timestamp.usecs-$ts0.usecs:...
Link: http://lkml.kernel.org/r/92746b06be67499c2a6217bd55395b350ad18fad.1522256721.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Mention the alternative of adding trace_clock=global to the kernel
command line when we detect that we've used an unstable clock across a
suspend/resume cycle.
Link: http://lkml.kernel.org/r/20180330150132.16903-2-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Across suspend, we may see a very large drift in timestamps if the sched
clock is unstable, prompting the global trace's ringbuffer code to warn
and suggest switching to the global clock. Preempt this request by
detecting when the sched clock is unstable (determined during
late_initcall) and automatically switching the default clock over to
trace_global_clock.
This should prevent requiring user interaction to resolve warnings such
as:
Delta way too big! 18446743856563626466 ts=18446744054496180323 write stamp = 197932553857
If you just came from a suspend/resume,
please switch to the trace global clock:
echo global > /sys/kernel/debug/tracing/trace_clock
Link: http://lkml.kernel.org/r/20180330150132.16903-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Commit 84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
tried to spread the interrupts accross all possible CPUs to make sure that
in case of phsyical hotplug (e.g. virtualization) the CPUs which get
plugged in after the device was initialized are targeted by a hardware
queue and the corresponding interrupt.
This has a downside in cases where the ACPI tables claim that there are
more possible CPUs than present CPUs and the number of interrupts to spread
out is smaller than the number of possible CPUs. These bogus ACPI tables
are unfortunately not uncommon.
In such a case the vector spreading algorithm assigns interrupts to CPUs
which can never be utilized and as a consequence these interrupts are
unused instead of being mapped to present CPUs. As a result the performance
of the device is suboptimal.
To fix this spread the interrupt vectors in two stages:
1) Spread as many interrupts as possible among the present CPUs
2) Spread the remaining vectors among non present CPUs
On a 8 core system, where CPU 0-3 are present and CPU 4-7 are not present,
for a device with 4 queues the resulting interrupt affinity is:
1) Before 84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
irq 39, cpu list 0
irq 40, cpu list 1
irq 41, cpu list 2
irq 42, cpu list 3
2) With 84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
irq 39, cpu list 0-2
irq 40, cpu list 3-4,6
irq 41, cpu list 5
irq 42, cpu list 7
3) With the refined vector spread applied:
irq 39, cpu list 0,4
irq 40, cpu list 1,6
irq 41, cpu list 2,5
irq 42, cpu list 3,7
On a 8 core system, where all CPUs are present the resulting interrupt
affinity for the 4 queues is:
irq 39, cpu list 0,1
irq 40, cpu list 2,3
irq 41, cpu list 4,5
irq 42, cpu list 6,7
This is independent of the number of CPUs which are online at the point of
initialization because in such a system the offline CPUs can be easily
onlined afterwards, while in non-present CPUs need to be plugged physically
or virtually which requires external interaction.
The downside of this approach is that in case of physical hotplug the
interrupt vector spreading might be suboptimal when CPUs 4-7 are physically
plugged. Suboptimal from a NUMA point of view and due to the single target
nature of interrupt affinities the later plugged CPUs might not be targeted
by interrupts at all.
Though, physical hotplug systems are not the common case while the broken
ACPI table disease is wide spread. So it's preferred to have as many
interrupts as possible utilized at the point where the device is
initialized.
Block multi-queue devices like NVME create a hardware queue per possible
CPU, so the goal of commit 84676c1f21 to assign one interrupt vector per
possible CPU is still achieved even with physical/virtual hotplug.
[ tglx: Changed from online to present CPUs for the first spreading stage,
renamed variables for readability sake, added comments and massaged
changelog ]
Reported-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Link: https://lkml.kernel.org/r/20180308105358.1506-5-ming.lei@redhat.com
To support two stage irq vector spreading, it's required to add a starting
point to the spreading function. No functional change, just preparatory
work for the actual two stage change.
[ tglx: Renamed variables, tidied up the code and massaged changelog ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Link: https://lkml.kernel.org/r/20180308105358.1506-4-ming.lei@redhat.com
No functional change, just prepare for converting to 2-stage irq vector
spreading.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Link: https://lkml.kernel.org/r/20180308105358.1506-3-ming.lei@redhat.com
The following patches will introduce two stage irq spreading for improving
irq spread on all possible CPUs.
No functional change.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Link: https://lkml.kernel.org/r/20180308105358.1506-2-ming.lei@redhat.com
When the allocation of node_to_possible_cpumask fails, then
irq_create_affinity_masks() returns with a pointer to the empty affinity
masks array, which will cause malfunction.
Reorder the allocations so the masks array allocation comes last and every
failure path returns NULL.
Fixes: 9a0ef98e18 ("genirq/affinity: Assign vectors to all present CPUs")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Add a new pointer argument to cpuidle_select() and to the ->select
cpuidle governor callback to allow a boolean value indicating
whether or not the tick should be stopped before entering the
selected state to be returned from there.
Make the ladder governor ignore that pointer (to preserve its
current behavior) and make the menu governor return 'false" through
it if:
(1) the idle exit latency is constrained at 0, or
(2) the selected state is a polling one, or
(3) the expected idle period duration is within the tick period
range.
In addition to that, the correction factor computations in the menu
governor need to take the possibility that the tick may not be
stopped into account to avoid artificially small correction factor
values. To that end, add a mechanism to record tick wakeups, as
suggested by Peter Zijlstra, and use it to modify the menu_update()
behavior when tick wakeup occurs. Namely, if the CPU is woken up by
the tick and the return value of tick_nohz_get_sleep_length() is not
within the tick boundary, the predicted idle duration is likely too
short, so make menu_update() try to compensate for that by updating
the governor statistics as though the CPU was idle for a long time.
Since the value returned through the new argument pointer of
cpuidle_select() is not used by its caller yet, this change by
itself is not expected to alter the functionality of the code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Since the subsequent changes will need a TICK_USEC definition
analogous to TICK_NSEC, rename the existing TICK_USEC as
USER_TICK_USEC, update its users and redefine TICK_USEC
accordingly.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Currently <linux/slab.h> #includes <linux/kmemleak.h> for no obvious
reason. It looks like it's only a convenience, so remove kmemleak.h
from slab.h and add <linux/kmemleak.h> to any users of kmemleak_* that
don't already #include it. Also remove <linux/kmemleak.h> from source
files that do not use it.
This is tested on i386 allmodconfig and x86_64 allmodconfig. It would
be good to run it through the 0day bot for other $ARCHes. I have
neither the horsepower nor the storage space for the other $ARCHes.
Update: This patch has been extensively build-tested by both the 0day
bot & kisskb/ozlabs build farms. Both of them reported 2 build failures
for which patches are included here (in v2).
[ slab.h is the second most used header file after module.h; kernel.h is
right there with slab.h. There could be some minor error in the
counting due to some #includes having comments after them and I didn't
combine all of those. ]
[akpm@linux-foundation.org: security/keys/big_key.c needs vmalloc.h, per sfr]
Link: http://lkml.kernel.org/r/e4309f98-3749-93e1-4bb7-d9501a39d015@infradead.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au> [2 build failures]
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [2 build failures]
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KASAN splats indicate that in some cases we free a live mm, then
continue to access it, with potentially disastrous results. This is
likely due to a mismatched mmdrop() somewhere in the kernel, but so far
the culprit remains elusive.
Let's have __mmdrop() verify that the mm isn't live for the current
task, similar to the existing check for init_mm. This way, we can catch
this class of issue earlier, and without requiring KASAN.
Currently, idle_task_exit() leaves active_mm stale after it switches to
init_mm. This isn't harmful, but will trigger the new assertions, so we
must adjust idle_task_exit() to update active_mm.
Link: http://lkml.kernel.org/r/20180312140103.19235-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull printk updates from Petr Mladek:
- Add info about loaded kdump kernel into the dump stack header
- Move dump-stack related code from printk.c to lib/dump_stack.c
- Write message about suspending consoles in KERN_INFO log level
* 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: change message to pr_info
printk: move dump stack related code to lib/dump_stack.c
print kdump kernel loaded status in stack dump
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
Make cpuidle_idle_call() decide whether or not to stop the tick.
First, the cpuidle_enter_s2idle() path deals with the tick (and with
the entire timekeeping for that matter) by itself and it doesn't need
the tick to be stopped beforehand.
Second, to address the issue with short idle duration predictions
by the idle governor after the tick has been stopped, it will be
necessary to change the ordering of cpuidle_select() with respect
to tick_nohz_idle_stop_tick(). To prepare for that, put a
tick_nohz_idle_stop_tick() call in the same branch in which
cpuidle_select() is called.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Push the decision whether or not to stop the tick somewhat deeper
into the idle loop.
Stopping the tick upfront leads to unpleasant outcomes in case the
idle governor doesn't agree with the nohz code on the duration of the
upcoming idle period. Specifically, if the tick has been stopped and
the idle governor predicts short idle, the situation is bad regardless
of whether or not the prediction is accurate. If it is accurate, the
tick has been stopped unnecessarily which means excessive overhead.
If it is not accurate, the CPU is likely to spend too much time in
the (shallow, because short idle has been predicted) idle state
selected by the governor [1].
As the first step towards addressing this problem, change the code
to make the tick stopping decision inside of the loop in do_idle().
In particular, do not stop the tick in the cpu_idle_poll() code path.
Also don't do that in tick_nohz_irq_exit() which doesn't really have
enough information on whether or not to stop the tick.
Link: https://marc.info/?l=linux-pm&m=150116085925208&w=2 # [1]
Link: https://tu-dresden.de/zih/forschung/ressourcen/dateien/projekte/haec/powernightmares.pdf
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Prepare the scheduler tick code for reworking the idle loop to
avoid stopping the tick in some cases.
The idea is to split the nohz idle entry call to decouple the idle
time stats accounting and preparatory work from the actual tick stop
code, in order to later be able to delay the tick stop once we reach
more power-knowledgeable callers.
Move away the tick_nohz_start_idle() invocation from
__tick_nohz_idle_enter(), rename the latter to
__tick_nohz_idle_stop_tick() and define tick_nohz_idle_stop_tick()
as a wrapper around it for calling it from the outside.
Make tick_nohz_idle_enter() only call tick_nohz_start_idle() instead
of calling the entire __tick_nohz_idle_enter(), add another wrapper
disabling and enabling interrupts around tick_nohz_idle_stop_tick()
and make the current callers of tick_nohz_idle_enter() call it too
to retain their current functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
It may be useful for an architecture to override the definitions of the
COMPAT_SYSCALL_DEFINE0() and __COMPAT_SYSCALL_DEFINEx() macros in
<linux/compat.h>, in particular to use a different calling convention
for syscalls. This patch provides a mechanism to do so, based on the
previously introduced CONFIG_ARCH_HAS_SYSCALL_WRAPPER. If it is enabled,
<asm/sycall_wrapper.h> is included in <linux/compat.h> and may be used
to define the macros mentioned above. Moreover, as the syscall calling
convention may be different if CONFIG_ARCH_HAS_SYSCALL_WRAPPER is set,
the compat syscall function prototypes in <linux/compat.h> are #ifndef'd
out in that case.
As some of the syscalls and/or compat syscalls may not be present,
the COND_SYSCALL() and COND_SYSCALL_COMPAT() macros in kernel/sys_ni.c
as well as the SYS_NI() and COMPAT_SYS_NI() macros in
kernel/time/posix-stubs.c can be re-defined in <asm/syscall_wrapper.h> iff
CONFIG_ARCH_HAS_SYSCALL_WRAPPER is enabled.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180405095307.3730-5-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
By renaming the functions we can get rid of the skip parameter
and have better code redability. It makes zero sense to have
things such as:
rq_clock_skip_update(rq, false)
When the skip request is in fact not going to happen. Ever. Rename
things such that we end up with:
rq_clock_skip_update(rq)
rq_clock_cancel_skipupdate(rq)
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: matt@codeblueprint.co.uk
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/20180404161539.nhadkff2aats74jh@linux-n805
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While running rt-tests' pi_stress program I got the following splat:
rq->clock_update_flags < RQCF_ACT_SKIP
WARNING: CPU: 27 PID: 0 at kernel/sched/sched.h:960 assert_clock_updated.isra.38.part.39+0x13/0x20
[...]
<IRQ>
enqueue_top_rt_rq+0xf4/0x150
? cpufreq_dbs_governor_start+0x170/0x170
sched_rt_rq_enqueue+0x65/0x80
sched_rt_period_timer+0x156/0x360
? sched_rt_rq_enqueue+0x80/0x80
__hrtimer_run_queues+0xfa/0x260
hrtimer_interrupt+0xcb/0x220
smp_apic_timer_interrupt+0x62/0x120
apic_timer_interrupt+0xf/0x20
</IRQ>
[...]
do_idle+0x183/0x1e0
cpu_startup_entry+0x5f/0x70
start_secondary+0x192/0x1d0
secondary_startup_64+0xa5/0xb0
We can get rid of it be the "traditional" means of adding an
update_rq_clock() call after acquiring the rq->lock in
do_sched_rt_period_timer().
The case for the RT task throttling (which this workload also hits)
can be ignored in that the skip_update call is actually bogus and
quite the contrary (the request bits are removed/reverted).
By setting RQCF_UPDATED we really don't care if the skip is happening
or not and will therefore make the assert_clock_updated() check happy.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: linux-kernel@vger.kernel.org
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/20180402164954.16255-1-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code refactoring
from Luis as he attempts to wrangle that codebase into something that is
managable, along with a bunch of userspace tests for it. Other than
that, a handful of small bugfixes and reverts of things that didn't work
out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSiGg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylPpACgyEKOur8rwp/3uBRxqhoFeWp1RtAAoIvlMjn6
MQ8LIeHNLRnpqGX5L78L
=93HA
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code
refactoring from Luis as he attempts to wrangle that codebase into
something that is managable, along with a bunch of userspace tests for
it. Other than that, a handful of small bugfixes and reverts of things
that didn't work out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
drivers: base: remove check for callback in coredump_store()
mt7601u: use firmware_request_cache() to address cache on reboot
firmware: add firmware_request_cache() to help with cache on reboot
firmware: fix typo on pr_info_once() when ignore_sysfs_fallback is used
firmware: explicitly include vmalloc.h
firmware: ensure the firmware cache is not used on incompatible calls
test_firmware: modify custom fallback tests to use unique files
firmware: add helper to check to see if fw cache is setup
firmware: fix checking for return values for fw_add_devm_name()
rename: _request_firmware_load() fw_load_sysfs_fallback()
test_firmware: test three firmware kernel configs using a proc knob
test_firmware: expand on library with shared helpers
firmware: enable to force disable the fallback mechanism at run time
firmware: enable run time change of forcing fallback loader
firmware: move firmware loader into its own directory
firmware: split firmware fallback functionality into its own file
firmware: move loading timeout under struct firmware_fallback_config
firmware: use helpers for setting up a temporary cache timeout
firmware: simplify CONFIG_FW_LOADER_USER_HELPER_FALLBACK further
drivers: base: add description for .coredump() callback
...
Nothing particularly stands out here, probably because people were tied
up with spectre/meltdown stuff last time around. Still, the main pieces
are:
- Rework of our CPU features framework so that we can whitelist CPUs that
don't require kpti even in a heterogeneous system
- Support for the IDC/DIC architecture extensions, which allow us to elide
instruction and data cache maintenance when writing out instructions
- Removal of the large memory model which resulted in suboptimal codegen
by the compiler and increased the use of literal pools, which could
potentially be used as ROP gadgets since they are mapped as executable
- Rework of forced signal delivery so that the siginfo_t is well-formed
and handling of show_unhandled_signals is consolidated and made
consistent between different fault types
- More siginfo cleanup based on the initial patches from Eric Biederman
- Workaround for Cortex-A55 erratum #1024718
- Some small ACPI IORT updates and cleanups from Lorenzo Pieralisi
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJaw1TCAAoJELescNyEwWM0gyQIAJVMK4QveBW+LwF96NYdZo16
p90Aa+nqKelh/s93govQArDMv1gxyuXdFlQZVOGPQHfqpz6RhJWmBA2tFsUbQrUc
OBcioPrRihqTmKBe+1r1XORwZxkVX6GGmCn0LYpPR7I3TjxXZpvxqaxGxiUvHkci
yVxWlDTyN/7eL3akhCpCDagN3Fxwk3QnJLqE3fxOFMlY7NvQcmUxcITiUl/s469q
xK6SWH9SRH1JK8jTHPitwUBiU//3FfCqSI9HLEdDIDoTuPcVM8UetWvi4QzrzJL1
UYg8lmU0CXNmflDzZJDaMf+qFApOrGxR0YVPpBzlQvxe0JIY69g48f+JzDPz8nc=
=+gNa
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Nothing particularly stands out here, probably because people were
tied up with spectre/meltdown stuff last time around. Still, the main
pieces are:
- Rework of our CPU features framework so that we can whitelist CPUs
that don't require kpti even in a heterogeneous system
- Support for the IDC/DIC architecture extensions, which allow us to
elide instruction and data cache maintenance when writing out
instructions
- Removal of the large memory model which resulted in suboptimal
codegen by the compiler and increased the use of literal pools,
which could potentially be used as ROP gadgets since they are
mapped as executable
- Rework of forced signal delivery so that the siginfo_t is
well-formed and handling of show_unhandled_signals is consolidated
and made consistent between different fault types
- More siginfo cleanup based on the initial patches from Eric
Biederman
- Workaround for Cortex-A55 erratum #1024718
- Some small ACPI IORT updates and cleanups from Lorenzo Pieralisi
- Misc cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (70 commits)
arm64: uaccess: Fix omissions from usercopy whitelist
arm64: fpsimd: Split cpu field out from struct fpsimd_state
arm64: tlbflush: avoid writing RES0 bits
arm64: cmpxchg: Include linux/compiler.h in asm/cmpxchg.h
arm64: move percpu cmpxchg implementation from cmpxchg.h to percpu.h
arm64: cmpxchg: Include build_bug.h instead of bug.h for BUILD_BUG
arm64: lse: Include compiler_types.h and export.h for out-of-line LL/SC
arm64: fpsimd: include <linux/init.h> in fpsimd.h
drivers/perf: arm_pmu_platform: do not warn about affinity on uniprocessor
perf: arm_spe: include linux/vmalloc.h for vmap()
Revert "arm64: Revert L1_CACHE_SHIFT back to 6 (64-byte cache line size)"
arm64: cpufeature: Avoid warnings due to unused symbols
arm64: Add work around for Arm Cortex-A55 Erratum 1024718
arm64: Delay enabling hardware DBM feature
arm64: Add MIDR encoding for Arm Cortex-A55 and Cortex-A35
arm64: capabilities: Handle shared entries
arm64: capabilities: Add support for checks based on a list of MIDRs
arm64: Add helpers for checking CPU MIDR against a range
arm64: capabilities: Clean up midr range helpers
arm64: capabilities: Change scope of VHE to Boot CPU feature
...
Pull irq updates from Thomas Gleixner:
"The usual pile of boring changes:
- Consolidate tasklet functions to share code instead of duplicating
it
- The first step for making the low level entry handler management on
multi-platform kernels generic
- A new sysfs file which allows to retrieve the wakeup state of
interrupts.
- Ensure that the interrupt thread follows the effective affinity and
not the programmed affinity to avoid cross core wakeups.
- Two new interrupt controller drivers (Microsemi Ocelot and Qualcomm
PDC)
- Fix the wakeup path clock handling for Reneasas interrupt chips.
- Rework the boot time register reset for ARM GIC-V2/3
- Better suspend/resume support for ARM GIV-V3/ITS
- Add missing locking to the ARM GIC set_type() callback
- Small fixes for the irq simulator code
- SPDX identifiers for the irq core code and removal of boiler plate
- Small cleanups all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
openrisc: Set CONFIG_MULTI_IRQ_HANDLER
arm64: Set CONFIG_MULTI_IRQ_HANDLER
genirq: Make GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER
irqchip/gic: Take lock when updating irq type
irqchip/gic: Update supports_deactivate static key to modern api
irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling
irqchip: Add a driver for the Microsemi Ocelot controller
dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller
irqchip/gic-v3: Probe for SCR_EL3 being clear before resetting AP0Rn
irqchip/gic-v3: Don't try to reset AP0Rn
irqchip/gic-v3: Do not check trigger configuration of partitionned LPIs
genirq: Remove license boilerplate/references
genirq: Add missing SPDX identifiers
genirq/matrix: Cleanup SPDX identifier
genirq: Cleanup top of file comments
genirq: Pass desc to __irq_free instead of irq number
irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
RISC-V: Move to the new GENERIC_IRQ_MULTI_HANDLER handler
genirq: Add CONFIG_GENERIC_IRQ_MULTI_HANDLER
...
Pull time(r) updates from Thomas Gleixner:
"A small set of updates for timers and timekeeping:
- The most interesting change is the consolidation of clock MONOTONIC
and clock BOOTTIME.
Clock MONOTONIC behaves now exactly like clock BOOTTIME and does
not longer ignore the time spent in suspend. A new clock
MONOTONIC_ACTIVE is provived which behaves like clock MONOTONIC in
kernels before this change. This allows applications to
programmatically check for the clock MONOTONIC behaviour.
As discussed in the review thread, this has the potential of
breaking user space and we might have to revert this. Knock on wood
that we can avoid that exercise.
- Updates to the NTP mechanism to improve accuracy
- A new kernel internal data structure to aid the ongoing Y2038 work.
- Cleanups and simplifications of the clocksource code.
- Make the alarmtimer code play nicely with debugobjects"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Init nanosleep alarm timer on stack
y2038: Introduce struct __kernel_old_timeval
tracing: Unify the "boot" and "mono" tracing clocks
hrtimer: Unify MONOTONIC and BOOTTIME clock behavior
posix-timers: Unify MONOTONIC and BOOTTIME clock behavior
timekeeping: Remove boot time specific code
Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior
timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock
timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock
timekeeping/ntp: Determine the multiplier directly from NTP tick length
timekeeping/ntp: Don't align NTP frequency adjustments to ticks
clocksource: Use ATTRIBUTE_GROUPS
clocksource: Use DEVICE_ATTR_RW/RO/WO to define device attributes
clocksource: Don't walk the clocksource list for empty override
These config switches enable the same code in the core and the not yet
converted architecture code. They can be selected both by randconfig builds
and cause linker error because the same symbols are defined twice.
Make the new GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER to
prevent that. The dependency will be removed once all architectures are
converted over.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20180404043130.31277-4-palmer@sifive.com
There will be a build warning -Wunused-function if CONFIG_CGROUP_BPF
isn't defined, since the only user is inside #ifdef CONFIG_CGROUP_BPF:
kernel/bpf/syscall.c:1229:12: warning: ‘bpf_prog_attach_check_attach_type’
defined but not used [-Wunused-function]
static int bpf_prog_attach_check_attach_type(const struct bpf_prog *prog,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Current code moves function bpf_prog_attach_check_attach_type inside
ifdef CONFIG_CGROUP_BPF.
Fixes: 5e43f899b0 ("bpf: Check attach type at prog load time")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It is possible to have multiple ULP tcp_release call paths in flight
if a sock is closed and simultaneously being removed from the sockmap
control path. The result would be setting the sk_prot to the saved
values on the first iteration and then on the second iteration setting
the value to NULL.
This patch resolves this by ensuring we only reset the sk_prot pointer
if we have a valid saved state to set.
Fixes: 4f738adba3 ("bpf: create tcp_bpf_ulp allowing BPF to monitor socket TX/RX data")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
