The ARM reference designs in the Versatile family: Integrator,
Versatile and RealView can make use of the new DRM driver as well.
We just need to create a bit of platform-specific code for them
that we isolate to its own file.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-7-linus.walleij@linaro.org
The old codebase has a delay between enabling and powering up the
PL11x.
According to the manual for PL110, ARM DDI 0161E page 1-5 and
the PL111 manual ARM DDI 0293C page 1-6, the power sequence should
be such that once Vdd is stable (which we assume it is at boot)
LCDEN is enabled first and then CLPOWER should be enabled
"after the signals have stabilized" and this is said to
be display-dependent. The old codebase uses 20ms.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-5-linus.walleij@linaro.org
We detect and enable the use of the PL110 variant, an earlier
incarnation of PL111. The only real difference is that the
control and interrupt enable registers have swapped place.
The Versatile AB and Versatile PB have a variant inbetween
PL110 and PL111, it is PL110 but they have already swapped the
two registers so those two need a bit of special handling.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-4-linus.walleij@linaro.org
This replaces the custom connector in the PL111 with the
panel bridge helper.
This works nicely for all standard panels, but since there
are several PL11x-based systems that will need to use the dumb
VGA connector bridge we use drm_of_find_panel_or_bridge()
and make some headroom for dealing with bridges that are
not panels as well, and drop a TODO in the code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-3-linus.walleij@linaro.org
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
If src_x/y were nonzero, we failed to shift them down by 16 to get the
pixel offset. The recent CMA helper function gets it right.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: bed41005e6 ("drm/pl111: Initial drm/kms driver for pl111")
Reported-by: Mircea Carausu <mircea.carausu@broadcom.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170603015733.13266-1-eric@anholt.net
Reviewed-by: Sean Paul <seanpaul@chromium.org>
structure pl111_display_funcs can be made static as it does not need to be
in global scope. Fixes sparse warning:
"warning: symbol 'pl111_display_funcs' was not declared. Should it
be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519110203.19417-1-colin.king@canonical.com
This is required for the panel to work on bcm911360, where CLCDCLK is
the fixed 200Mhz AXI41 clock. The rate set is still passed up to the
CLCDCLK, for platforms that have a settable rate on that one.
v2: Set SET_RATE_PARENT (caught by Linus Walleij), depend on
COMMON_CLK.
v3: Mark the clk_ops static (caught by Stephen).
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508193348.30236-1-eric@anholt.net
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
This is a modesetting driver for the pl111 CLCD display controller
found on various ARM platforms such as the Versatile Express. The
driver has only been tested on the bcm911360_entphn platform so far,
with PRIME-based buffer sharing between vc4 and clcd.
It reuses the existing devicetree binding, while not using quite as
many of its properties as the fbdev driver does (those are left for
future work).
v2: Nearly complete rewrite by anholt, cutting 2/3 of the code thanks
to DRM core's excellent new helpers.
v3: Don't match pl110 any more, don't attach if we don't have a DRM
panel, use DRM_GEM_CMA_FOPS, update MAINTAINERS, use the simple
display helper, use drm_gem_cma_dumb_create (same as our wrapper).
v4: Change the driver's .name to not clash with fbdev in sysfs, drop
platform alias, drop redundant "drm" in DRM driver name, hook up
.prepare_fb to the CMA helper so that DMA fences should work.
v5: Move register definitions inside the driver directory, fix build
in COMPILE_TEST and !AMBA mode.
v6: Drop TIM2_CLKSEL for now to be consistent with existing DT
bindings, switch back to external register definitions.
Signed-off-by: Tom Cooksey <tom.cooksey@arm.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> (v5)
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413031746.12921-2-eric@anholt.net
