linux_dsm_epyc7002/drivers/gpu/drm/pl111/pl111_display.c
Linus Walleij 52289a07a0 drm/pl111: Insert delay before powering up PL11x
The old codebase has a delay between enabling and powering up the
PL11x.

According to the manual for PL110, ARM DDI 0161E page 1-5 and
the PL111 manual ARM DDI 0293C page 1-6, the power sequence should
be such that once Vdd is stable (which we assume it is at boot)
LCDEN is enabled first and then CLPOWER should be enabled
"after the signals have stabilized" and this is said to
be display-dependent. The old codebase uses 20ms.

Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-5-linus.walleij@linaro.org
2017-09-10 23:58:29 +02:00

469 lines
11 KiB
C

/*
* (C) COPYRIGHT 2012-2013 ARM Limited. All rights reserved.
*
* Parts of this file were based on sources as follows:
*
* Copyright (c) 2006-2008 Intel Corporation
* Copyright (c) 2007 Dave Airlie <airlied@linux.ie>
* Copyright (C) 2011 Texas Instruments
*
* This program is free software and is provided to you under the terms of the
* GNU General Public License version 2 as published by the Free Software
* Foundation, and any use by you of this program is subject to the terms of
* such GNU licence.
*
*/
#include <linux/amba/clcd-regs.h>
#include <linux/clk.h>
#include <linux/version.h>
#include <linux/dma-buf.h>
#include <linux/of_graph.h>
#include <drm/drmP.h>
#include <drm/drm_gem_cma_helper.h>
#include <drm/drm_gem_framebuffer_helper.h>
#include <drm/drm_fb_cma_helper.h>
#include "pl111_drm.h"
irqreturn_t pl111_irq(int irq, void *data)
{
struct pl111_drm_dev_private *priv = data;
u32 irq_stat;
irqreturn_t status = IRQ_NONE;
irq_stat = readl(priv->regs + CLCD_PL111_MIS);
if (!irq_stat)
return IRQ_NONE;
if (irq_stat & CLCD_IRQ_NEXTBASE_UPDATE) {
drm_crtc_handle_vblank(&priv->pipe.crtc);
status = IRQ_HANDLED;
}
/* Clear the interrupt once done */
writel(irq_stat, priv->regs + CLCD_PL111_ICR);
return status;
}
static int pl111_display_check(struct drm_simple_display_pipe *pipe,
struct drm_plane_state *pstate,
struct drm_crtc_state *cstate)
{
const struct drm_display_mode *mode = &cstate->mode;
struct drm_framebuffer *old_fb = pipe->plane.state->fb;
struct drm_framebuffer *fb = pstate->fb;
if (mode->hdisplay % 16)
return -EINVAL;
if (fb) {
u32 offset = drm_fb_cma_get_gem_addr(fb, pstate, 0);
/* FB base address must be dword aligned. */
if (offset & 3)
return -EINVAL;
/* There's no pitch register -- the mode's hdisplay
* controls it.
*/
if (fb->pitches[0] != mode->hdisplay * fb->format->cpp[0])
return -EINVAL;
/* We can't change the FB format in a flicker-free
* manner (and only update it during CRTC enable).
*/
if (old_fb && old_fb->format != fb->format)
cstate->mode_changed = true;
}
return 0;
}
static void pl111_display_enable(struct drm_simple_display_pipe *pipe,
struct drm_crtc_state *cstate)
{
struct drm_crtc *crtc = &pipe->crtc;
struct drm_plane *plane = &pipe->plane;
struct drm_device *drm = crtc->dev;
struct pl111_drm_dev_private *priv = drm->dev_private;
const struct drm_display_mode *mode = &cstate->mode;
struct drm_framebuffer *fb = plane->state->fb;
struct drm_connector *connector = priv->connector;
u32 cntl;
u32 ppl, hsw, hfp, hbp;
u32 lpp, vsw, vfp, vbp;
u32 cpl, tim2;
int ret;
ret = clk_set_rate(priv->clk, mode->clock * 1000);
if (ret) {
dev_err(drm->dev,
"Failed to set pixel clock rate to %d: %d\n",
mode->clock * 1000, ret);
}
clk_prepare_enable(priv->clk);
ppl = (mode->hdisplay / 16) - 1;
hsw = mode->hsync_end - mode->hsync_start - 1;
hfp = mode->hsync_start - mode->hdisplay - 1;
hbp = mode->htotal - mode->hsync_end - 1;
lpp = mode->vdisplay - 1;
vsw = mode->vsync_end - mode->vsync_start - 1;
vfp = mode->vsync_start - mode->vdisplay;
vbp = mode->vtotal - mode->vsync_end;
cpl = mode->hdisplay - 1;
writel((ppl << 2) |
(hsw << 8) |
(hfp << 16) |
(hbp << 24),
priv->regs + CLCD_TIM0);
writel(lpp |
(vsw << 10) |
(vfp << 16) |
(vbp << 24),
priv->regs + CLCD_TIM1);
spin_lock(&priv->tim2_lock);
tim2 = readl(priv->regs + CLCD_TIM2);
tim2 &= (TIM2_BCD | TIM2_PCD_LO_MASK | TIM2_PCD_HI_MASK);
if (mode->flags & DRM_MODE_FLAG_NHSYNC)
tim2 |= TIM2_IHS;
if (mode->flags & DRM_MODE_FLAG_NVSYNC)
tim2 |= TIM2_IVS;
if (connector->display_info.bus_flags & DRM_BUS_FLAG_DE_LOW)
tim2 |= TIM2_IOE;
if (connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_NEGEDGE)
tim2 |= TIM2_IPC;
tim2 |= cpl << 16;
writel(tim2, priv->regs + CLCD_TIM2);
spin_unlock(&priv->tim2_lock);
writel(0, priv->regs + CLCD_TIM3);
/* Hard-code TFT panel */
cntl = CNTL_LCDEN | CNTL_LCDTFT | CNTL_LCDVCOMP(1);
/* Note that the the hardware's format reader takes 'r' from
* the low bit, while DRM formats list channels from high bit
* to low bit as you read left to right.
*/
switch (fb->format->format) {
case DRM_FORMAT_ABGR8888:
case DRM_FORMAT_XBGR8888:
cntl |= CNTL_LCDBPP24;
break;
case DRM_FORMAT_ARGB8888:
case DRM_FORMAT_XRGB8888:
cntl |= CNTL_LCDBPP24 | CNTL_BGR;
break;
case DRM_FORMAT_BGR565:
cntl |= CNTL_LCDBPP16_565;
break;
case DRM_FORMAT_RGB565:
cntl |= CNTL_LCDBPP16_565 | CNTL_BGR;
break;
case DRM_FORMAT_ABGR1555:
case DRM_FORMAT_XBGR1555:
cntl |= CNTL_LCDBPP16;
break;
case DRM_FORMAT_ARGB1555:
case DRM_FORMAT_XRGB1555:
cntl |= CNTL_LCDBPP16 | CNTL_BGR;
break;
case DRM_FORMAT_ABGR4444:
case DRM_FORMAT_XBGR4444:
cntl |= CNTL_LCDBPP16_444;
break;
case DRM_FORMAT_ARGB4444:
case DRM_FORMAT_XRGB4444:
cntl |= CNTL_LCDBPP16_444 | CNTL_BGR;
break;
default:
WARN_ONCE(true, "Unknown FB format 0x%08x\n",
fb->format->format);
break;
}
/* Power sequence: first enable and chill */
writel(cntl, priv->regs + priv->ctrl);
/*
* We expect this delay to stabilize the contrast
* voltage Vee as stipulated by the manual
*/
msleep(20);
/* Power Up */
cntl |= CNTL_LCDPWR;
writel(cntl, priv->regs + priv->ctrl);
drm_crtc_vblank_on(crtc);
}
void pl111_display_disable(struct drm_simple_display_pipe *pipe)
{
struct drm_crtc *crtc = &pipe->crtc;
struct drm_device *drm = crtc->dev;
struct pl111_drm_dev_private *priv = drm->dev_private;
u32 cntl;
drm_crtc_vblank_off(crtc);
/* Power Down */
cntl = readl(priv->regs + priv->ctrl);
if (cntl & CNTL_LCDPWR) {
cntl &= ~CNTL_LCDPWR;
writel(cntl, priv->regs + priv->ctrl);
}
/*
* We expect this delay to stabilize the contrast voltage Vee as
* stipulated by the manual
*/
msleep(20);
/* Disable */
writel(0, priv->regs + priv->ctrl);
clk_disable_unprepare(priv->clk);
}
static void pl111_display_update(struct drm_simple_display_pipe *pipe,
struct drm_plane_state *old_pstate)
{
struct drm_crtc *crtc = &pipe->crtc;
struct drm_device *drm = crtc->dev;
struct pl111_drm_dev_private *priv = drm->dev_private;
struct drm_pending_vblank_event *event = crtc->state->event;
struct drm_plane *plane = &pipe->plane;
struct drm_plane_state *pstate = plane->state;
struct drm_framebuffer *fb = pstate->fb;
if (fb) {
u32 addr = drm_fb_cma_get_gem_addr(fb, pstate, 0);
writel(addr, priv->regs + CLCD_UBAS);
}
if (event) {
crtc->state->event = NULL;
spin_lock_irq(&crtc->dev->event_lock);
if (crtc->state->active && drm_crtc_vblank_get(crtc) == 0)
drm_crtc_arm_vblank_event(crtc, event);
else
drm_crtc_send_vblank_event(crtc, event);
spin_unlock_irq(&crtc->dev->event_lock);
}
}
int pl111_enable_vblank(struct drm_device *drm, unsigned int crtc)
{
struct pl111_drm_dev_private *priv = drm->dev_private;
writel(CLCD_IRQ_NEXTBASE_UPDATE, priv->regs + priv->ienb);
return 0;
}
void pl111_disable_vblank(struct drm_device *drm, unsigned int crtc)
{
struct pl111_drm_dev_private *priv = drm->dev_private;
writel(0, priv->regs + priv->ienb);
}
static int pl111_display_prepare_fb(struct drm_simple_display_pipe *pipe,
struct drm_plane_state *plane_state)
{
return drm_gem_fb_prepare_fb(&pipe->plane, plane_state);
}
static const struct drm_simple_display_pipe_funcs pl111_display_funcs = {
.check = pl111_display_check,
.enable = pl111_display_enable,
.disable = pl111_display_disable,
.update = pl111_display_update,
.prepare_fb = pl111_display_prepare_fb,
};
static int pl111_clk_div_choose_div(struct clk_hw *hw, unsigned long rate,
unsigned long *prate, bool set_parent)
{
int best_div = 1, div;
struct clk_hw *parent = clk_hw_get_parent(hw);
unsigned long best_prate = 0;
unsigned long best_diff = ~0ul;
int max_div = (1 << (TIM2_PCD_LO_BITS + TIM2_PCD_HI_BITS)) - 1;
for (div = 1; div < max_div; div++) {
unsigned long this_prate, div_rate, diff;
if (set_parent)
this_prate = clk_hw_round_rate(parent, rate * div);
else
this_prate = *prate;
div_rate = DIV_ROUND_UP_ULL(this_prate, div);
diff = abs(rate - div_rate);
if (diff < best_diff) {
best_div = div;
best_diff = diff;
best_prate = this_prate;
}
}
*prate = best_prate;
return best_div;
}
static long pl111_clk_div_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *prate)
{
int div = pl111_clk_div_choose_div(hw, rate, prate, true);
return DIV_ROUND_UP_ULL(*prate, div);
}
static unsigned long pl111_clk_div_recalc_rate(struct clk_hw *hw,
unsigned long prate)
{
struct pl111_drm_dev_private *priv =
container_of(hw, struct pl111_drm_dev_private, clk_div);
u32 tim2 = readl(priv->regs + CLCD_TIM2);
int div;
if (tim2 & TIM2_BCD)
return prate;
div = tim2 & TIM2_PCD_LO_MASK;
div |= (tim2 & TIM2_PCD_HI_MASK) >>
(TIM2_PCD_HI_SHIFT - TIM2_PCD_LO_BITS);
div += 2;
return DIV_ROUND_UP_ULL(prate, div);
}
static int pl111_clk_div_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long prate)
{
struct pl111_drm_dev_private *priv =
container_of(hw, struct pl111_drm_dev_private, clk_div);
int div = pl111_clk_div_choose_div(hw, rate, &prate, false);
u32 tim2;
spin_lock(&priv->tim2_lock);
tim2 = readl(priv->regs + CLCD_TIM2);
tim2 &= ~(TIM2_BCD | TIM2_PCD_LO_MASK | TIM2_PCD_HI_MASK);
if (div == 1) {
tim2 |= TIM2_BCD;
} else {
div -= 2;
tim2 |= div & TIM2_PCD_LO_MASK;
tim2 |= (div >> TIM2_PCD_LO_BITS) << TIM2_PCD_HI_SHIFT;
}
writel(tim2, priv->regs + CLCD_TIM2);
spin_unlock(&priv->tim2_lock);
return 0;
}
static const struct clk_ops pl111_clk_div_ops = {
.recalc_rate = pl111_clk_div_recalc_rate,
.round_rate = pl111_clk_div_round_rate,
.set_rate = pl111_clk_div_set_rate,
};
static int
pl111_init_clock_divider(struct drm_device *drm)
{
struct pl111_drm_dev_private *priv = drm->dev_private;
struct clk *parent = devm_clk_get(drm->dev, "clcdclk");
struct clk_hw *div = &priv->clk_div;
const char *parent_name;
struct clk_init_data init = {
.name = "pl111_div",
.ops = &pl111_clk_div_ops,
.parent_names = &parent_name,
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
};
int ret;
if (IS_ERR(parent)) {
dev_err(drm->dev, "CLCD: unable to get clcdclk.\n");
return PTR_ERR(parent);
}
parent_name = __clk_get_name(parent);
spin_lock_init(&priv->tim2_lock);
div->init = &init;
ret = devm_clk_hw_register(drm->dev, div);
priv->clk = div->clk;
return ret;
}
int pl111_display_init(struct drm_device *drm)
{
struct pl111_drm_dev_private *priv = drm->dev_private;
struct device *dev = drm->dev;
struct device_node *endpoint;
u32 tft_r0b0g0[3];
int ret;
endpoint = of_graph_get_next_endpoint(dev->of_node, NULL);
if (!endpoint)
return -ENODEV;
if (of_property_read_u32_array(endpoint,
"arm,pl11x,tft-r0g0b0-pads",
tft_r0b0g0,
ARRAY_SIZE(tft_r0b0g0)) != 0) {
dev_err(dev, "arm,pl11x,tft-r0g0b0-pads should be 3 ints\n");
of_node_put(endpoint);
return -ENOENT;
}
of_node_put(endpoint);
if (tft_r0b0g0[0] != 0 ||
tft_r0b0g0[1] != 8 ||
tft_r0b0g0[2] != 16) {
dev_err(dev, "arm,pl11x,tft-r0g0b0-pads != [0,8,16] not yet supported\n");
return -EINVAL;
}
ret = pl111_init_clock_divider(drm);
if (ret)
return ret;
ret = drm_simple_display_pipe_init(drm, &priv->pipe,
&pl111_display_funcs,
priv->variant->formats,
priv->variant->nformats,
NULL,
priv->connector);
if (ret)
return ret;
return 0;
}