Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree.
they are:
1) Fix leak in the error path of nft_expr_init(), from Liping Zhang.
2) Tracing from nf_tables cannot be disabled, also from Zhang.
3) Fix an integer overflow on 32bit archs when setting the number of
hashtable buckets, from Florian Westphal.
4) Fix configuration of ipvs sync in backup mode with IPv6 address,
from Quentin Armitage via Simon Horman.
5) Fix incorrect timeout calculation in nft_ct NFT_CT_EXPIRATION,
from Florian Westphal.
6) Skip clash resolution in conntrack insertion races if NAT is in
place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The clash resolution is not easy to apply if the NAT table is
registered. Even if no NAT rules are installed, the nul-binding ensures
that a unique tuple is used, thus, the packet that loses race gets a
different source port number, as described by:
http://marc.info/?l=netfilter-devel&m=146818011604484&w=2
Clash resolution with NAT is also problematic if addresses/port range
ports are used since the conntrack that wins race may describe a
different mangling that we may have earlier applied to the packet via
nf_nat_setup_info().
Fixes: 71d8c47fc6 ("netfilter: conntrack: introduce clash resolution on insertion race")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Jon Maloy says:
====================
tipc: three small fixes
Fixes for some broadcast link problems that may occur in large systems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In test situations with many nodes and a heavily stressed system we have
observed that the transmission broadcast link may fail due to an
excessive number of retransmissions of the same packet. In such
situations we need to reset all unicast links to all peers, in order to
reset and re-synchronize the broadcast link.
In this commit, we add a new function tipc_bearer_reset_all() to be used
in such situations. The function scans across all bearers and resets all
their pertaining links.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a new receiver peer has been added to the broadcast transmission
link, we allow immediate transmission of new broadcast packets, trusting
that the new peer will not accept the packets until it has received the
previously sent unicast broadcast initialiation message. In the same
way, the sender must not accept any acknowledges until it has itself
received the broadcast initialization from the peer, as well as
confirmation of the reception of its own initialization message.
Furthermore, when a receiver peer goes down, the sender has to produce
the missing acknowledges from the lost peer locally, in order ensure
correct release of the buffers that were expected to be acknowledged by
the said peer.
In a highly stressed system we have observed that contact with a peer
may come up and be lost before the above mentioned broadcast initial-
ization and confirmation have been received. This leads to the locally
produced acknowledges being rejected, and the non-acknowledged buffers
to linger in the broadcast link transmission queue until it fills up
and the link goes into permanent congestion.
In this commit, we remedy this by temporarily setting the corresponding
broadcast receive link state to ESTABLISHED and the 'bc_peer_is_up'
state to true before we issue the local acknowledges. This ensures that
those acknowledges will always be accepted. The mentioned state values
are restored immediately afterwards when the link is reset.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first contact between two nodes, an endpoint might sometimes have
time to send out a LINK_PROTOCOL/STATE packet before it has received
the broadcast initialization packet from the peer, i.e., before it has
received a valid broadcast packet number to add to the 'bc_ack' field
of the protocol message.
This means that the peer endpoint will receive a protocol packet with an
invalid broadcast acknowledge value of 0. Under unlucky circumstances
this may lead to the original, already received acknowledge value being
overwritten, so that the whole broadcast link goes stale after a while.
We fix this by delaying the setting of the link field 'bc_peer_is_up'
until we know that the peer really has received our own broadcast
initialization message. The latter is always sent out as the first
unicast message on a link, and always with seqeunce number 1. Because
of this, we only need to look for a non-zero unicast acknowledge value
in the arriving STATE messages, and once that is confirmed we know we
are safe and can set the mentioned field. Before this moment, we must
ignore all broadcast acknowledges from the peer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8153-AD supports a persistent system specific MAC address.
This means a device plugged into two different systems with host side
support will show different (but persistent) MAC addresses.
This information for the system's persistent MAC address is burned in when
the system HW is built and available under \_SB.AMAC in the DSDT at runtime.
This technology is currently implemented in the Dell TB15 and WD15 Type-C
docks. More information is available here:
http://www.dell.com/support/article/us/en/04/SLN301147
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Trofimovich reported that pulse audio sends SCM_CREDENTIALS
as a control message to TCP. Since __sock_cmsg_send does not
support SCM_RIGHTS and SCM_CREDENTIALS, it returns an error and
hence breaks pulse audio over TCP.
SCM_RIGHTS and SCM_CREDENTIALS are sent on the SOL_SOCKET layer
but they semantically belong to SOL_UNIX. Since all
cmsg-processing functions including sock_cmsg_send ignore control
messages of other layers, it is best to ignore SCM_RIGHTS
and SCM_CREDENTIALS for consistency (and also for fixing pulse
audio over TCP).
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: Sergei Trofimovich <slyfox@gentoo.org>
Tested-by: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum is reporting for a crash in fib_dump_info
when nh_dev = NULL and fib_nhs == 1:
Pid: 50, comm: netlink.exe Not tainted 4.7.0-rc5+
RIP: 0033:[<00000000602b3d18>]
RSP: 0000000062623890 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 000000006261b800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000024 RDI: 000000006245ba00
RBP: 00000000626238f0 R08: 000000000000029c R09: 0000000000000000
R10: 0000000062468038 R11: 000000006245ba00 R12: 000000006245ba00
R13: 00000000625f96c0 R14: 00000000601e16f0 R15: 0000000000000000
Kernel panic - not syncing: Kernel mode fault at addr 0x2e0, ip 0x602b3d18
CPU: 0 PID: 50 Comm: netlink.exe Not tainted 4.7.0-rc5+ #581
Stack:
626238f0 960226a02 00000400 000000fe
62623910 600afca7 62623970 62623a48
62468038 00000018 00000000 00000000
Call Trace:
[<602b3e93>] rtmsg_fib+0xd3/0x190
[<602b6680>] fib_table_insert+0x260/0x500
[<602b0e5d>] inet_rtm_newroute+0x4d/0x60
[<60250def>] rtnetlink_rcv_msg+0x8f/0x270
[<60267079>] netlink_rcv_skb+0xc9/0xe0
[<60250d4b>] rtnetlink_rcv+0x3b/0x50
[<60265400>] netlink_unicast+0x1a0/0x2c0
[<60265e47>] netlink_sendmsg+0x3f7/0x470
[<6021dc9a>] sock_sendmsg+0x3a/0x90
[<6021e0d0>] ___sys_sendmsg+0x300/0x360
[<6021fa64>] __sys_sendmsg+0x54/0xa0
[<6021fac0>] SyS_sendmsg+0x10/0x20
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
$ addr2line -e vmlinux -i 0x602b3d18
include/linux/inetdevice.h:222
net/ipv4/fib_semantics.c:1264
Problem happens when RTNH_F_LINKDOWN is provided from user space
when creating routes that do not use the flag, catched with
netlink fuzzer.
Currently, the kernel allows user space to set both flags
to nh_flags and fib_flags but this is not intentional, the
assumption was that they are not set. Fix this by rejecting
both flags with EINVAL.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Fixes: 0eeb075fad ("net: ipv4 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Dinesh Dutt <ddutt@cumulusnetworks.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee ("tcp: implement RFC 5961 3.2")
Reported-by: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If socket filter truncates an udp packet below the length of UDP header
in udpv6_queue_rcv_skb() or udp_queue_rcv_skb(), it will trigger a
BUG_ON in skb_pull_rcsum(). This BUG_ON (and therefore a system crash if
kernel is configured that way) can be easily enforced by an unprivileged
user which was reported as CVE-2016-6162. For a reproducer, see
http://seclists.org/oss-sec/2016/q3/8
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rc is not initialized so it can contain garbage if it is not
set by the call to bnxt_read_sfp_module_eeprom_info. Ensure
garbage is not returned by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix possible NULL pointer dereference for vlan_insert_tag (two patches)
- Fix reference handling in some features, which may lead to reference
leaks or invalid memory access (four patches)
- Fix speedy join: DHCP packets handled by the gateway feature should
be sent with 4-address unicast instead of 3-address unicast to make
speedy join work. This fixes/speeds up DHCP assignment for clients
which join a mesh for the first time. (one patch)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Z04
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20160708' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are a couple batman-adv bugfix patches, all by Sven Eckelmann:
- Fix possible NULL pointer dereference for vlan_insert_tag (two patches)
- Fix reference handling in some features, which may lead to reference
leaks or invalid memory access (four patches)
- Fix speedy join: DHCP packets handled by the gateway feature should
be sent with 4-address unicast instead of 3-address unicast to make
speedy join work. This fixes/speeds up DHCP assignment for clients
which join a mesh for the first time. (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
Second Round of IPVS Fixes for v4.7
The fix from Quentin Armitage allows the backup sync daemon to
be bound to a link-local mcast IPv6 address as is already the case
for IPv4.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the prep work I did before enabling BH while handling socket backlog,
I missed two points in DCCP :
1) dccp_v4_ctl_send_reset() uses bh_lock_sock(), assuming BH were
blocked. It is not anymore always true.
2) dccp_v4_route_skb() was using __IP_INC_STATS() instead of
IP_INC_STATS()
A similar fix was done for TCP, in commit 47dcc20a39
("ipv4: tcp: ip_send_unicast_reply() is not BH safe")
Fixes: 7309f8821f ("dccp: do not assume DCCP code is non preemptible")
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon says:
====================
ibmvnic driver bugfixes and improvements
Miscellaneous fixes and improvements on the ibmvnic driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if there is no VNIC server available during the driver
probe, the driver should wait until it receives an initialization
request from the VNIC Server to start the login process. Recent testing
has show that this is incorrectly handled in the current driver.
The proposed solution handles this initialization request by scheduling
a task in the shared workqueue that completes the login process and
registers the net device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a function that handles sub-CRQ IRQ creation
separately from sub-CRQ initialization. Another function is then needed
to release sub-CRQ resources prior to sub-CRQ IRQ creation.
These additions allow the driver probe function to be simplified,
specifically during the VNIC Server login process. A timeout is also
included while waiting for completion of the login process in case
the VNIC Server is not available or some other error occurs.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ mappings were not being properly disposed when releasing sub-CRQ's.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ibmvnic uses multiple tx queues, start and stop all queues when
opening and closing devices.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN_WAKE_EN is not used to determine if the device could support
WOL. It is used to signal a GPIO pin when a WOL event occurs. The WOL
still works even though it is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd2 ("ppp: take reference on channels netns")
Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-ppp@vger.kernel.org
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aebea2ba0f ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to compute timeout.expires - jiffies, not the other way around.
Add a helper, another patch can then later change more places in
conntrack code where we currently open-code this.
Will allow us to only change one place later when we remove per-ct timer.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When using HEAD from
https://git.kernel.org/cgit/utils/kernel/ipvsadm/ipvsadm.git/,
the command:
ipvsadm --start-daemon backup --mcast-interface eth0.60 \
--mcast-group ff02::1:81
fails with the error message:
Argument list too long
whereas both:
ipvsadm --start-daemon master --mcast-interface eth0.60 \
--mcast-group ff02::1:81
and:
ipvsadm --start-daemon backup --mcast-interface eth0.60 \
--mcast-group 224.0.0.81
are successful.
The error message "Argument list too long" isn't helpful. The error occurs
because an IPv6 address is given in backup mode.
The error is in make_receive_sock() in net/netfilter/ipvs/ip_vs_sync.c,
since it fails to set the interface on the address or the socket before
calling inet6_bind() (via sock->ops->bind), where the test
'if (!sk->sk_bound_dev_if)' failed.
Setting sock->sk->sk_bound_dev_if on the socket before calling
inet6_bind() resolves the issue.
Fixes: d33288172e ("ipvs: add more mcast parameters for the sync daemon")
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Pull networking fixes from David Miller:
1) All users of AF_PACKET's fanout feature want a symmetric packet
header hash for load balancing purposes, so give it to them.
2) Fix vlan state synchronization in e1000e, from Jarod Wilson.
3) Use correct socket pointer in ip_skb_dst_mtu(), from Shmulik
Ladkani.
4) mlx5 bug fixes from Mohamad Haj Yahia, Daniel Jurgens, Matthew
Finlay, Rana Shahout, and Shaker Daibes. Mostly to do with
operation timeouts and PCI error handling.
5) Fix checksum handling in mirred packet action, from WANG Cong.
6) Set skb->dev correctly when transmitting in !protect_frames case of
macsec driver, from Daniel Borkmann.
7) Fix MTU calculation in geneve driver, from Haishuang Yan.
8) Missing netif_napi_del() in unregister path of qeth driver, from
Ursula Braun.
9) Handle malformed route netlink messages in decnet properly, from
Vergard Nossum.
10) Memory leak of percpu data in ipv6 routing code, from Martin KaFai
Lau.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ipv6: Fix mem leak in rt6i_pcpu
net: fix decnet rtnexthop parsing
cxgb4: update latest firmware version supported
net/mlx5: Avoid setting unused var when modifying vport node GUID
bonding: fix enslavement slave link notifications
r8152: fix runtime function for RTL8152
qeth: delete napi struct when removing a qeth device
Revert "fsl/fman: fix error handling"
fsl/fman: fix error handling
cdc_ncm: workaround for EM7455 "silent" data interface
RDS: fix rds_tcp_init() error path
geneve: fix max_mtu setting
net: phy: dp83867: Fix initialization of PHYCR register
enc28j60: Fix race condition in enc28j60 driver
net: stmmac: Fix null-function call in ISR on stmmac1000
tipc: fix nl compat regression for link statistics
net: bcmsysport: Device stats are unsigned long
macsec: set actual real device for xmit when !protect_frames
net_sched: fix mirrored packets checksum
packet: Use symmetric hash for PACKET_FANOUT_HASH.
...
Here are a collection of small fixes: at this time, we've got a
slightly high amount, but all small and trivial fixes, and nothing
scary can be seen there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8ER4
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes: at this time, we've got a
slightly high amount, but all small and trivial fixes, and nothing
scary can be seen there"
* tag 'sound-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek: Add Lenovo L460 to docking unit fixup
ALSA: timer: Fix negative queue usage by racy accesses
ASoC: rt5645: fix reg-2f default value.
ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode
ALSA: au88x0: Fix calculation in vortex_wtdma_bufshift()
ALSA: hda - Add PCI ID for Kabylake-H
ALSA: echoaudio: Fix memory allocation
ASoC: Intel: atom: fix missing breaks that would cause the wrong operation to execute
ALSA: hda - fix read before array start
ASoC: cx20442: set tty->receiver_room in v253_open
ASoC: ak4613: Enable cache usage to fix crashes on resume
ASoC: wm8940: Enable cache usage to fix crashes on resume
ASoC: Intel: Skylake: Initialize module list for Broxton
ASoC: wm5102: Correct supported channels on trace compressed DAI
ASoC: wm5110: Add missing route from OUT3R to SYSCLK
ASoC: rt5670: fix HP Playback Volume control
ASoC: hdmi-codec: select CONFIG_HDMI
ASoC: davinci-mcasp: Fix dra7 DMA offset when using CFG port
ASoC: hdac_hdmi: Fix potential NULL dereference
ASoC: ak4613: Remove owner assignment from platform_driver
...
A single fix this time, closing a window where ioctl args are fetched twice.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xPkx
-----END PGP SIGNATURE-----
Merge tag 'chrome-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform fix from Olof Johansson:
"A single fix this time, closing a window where ioctl args are fetched
twice"
* tag 'chrome-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: cros_ec_dev - double fetch bug in ioctl
Speedy join only works when the received packet is either broadcast or an
4addr unicast packet. Thus packets converted from broadcast to unicast via
the gateway handling code have to be converted to 4addr packets to allow
the receiving gateway server to add the sender address as temporary entry
to the translation table.
Not doing it will make the batman-adv gateway server drop the DHCP response
in many situations because it doesn't yet have the TT entry for the
destination of the DHCP response.
Fixes: 371351731e ("batman-adv: change interface_rx to get orig node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
No support for pbss results in a memory leak for the acl_data
(if parse_acl_data succeeds). Fix this by moving the ACL parsing later.
Cc: stable@vger.kernel.org
Fixes: 34d505193b ("cfg80211: basic support for PBSS network type")
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
dn_fib_count_nhs() could enter an infinite loop if nhp->rtnh_len == 0
(i.e. if userspace passes a malformed netlink message).
Let's use the helpers from net/nexthop.h which take care of all this
stuff. We can do exactly the same as e.g. fib_count_nexthops() and
fib_get_nhs() from net/ipv4/fib_semantics.c.
This fixes the softlockup for me.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445 ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Olof Johansson <olof@lixom.net>
Change t4fw_version.h to update latest firmware version number
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC complains on unused-but-set-variable, clean this up.
Fixes: 23898c763f ('net/mlx5: E-Switch, Modify node guid on vf set MAC')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, link notifications are not sent by
bond_set_slave_link_state() upon enslavement if
the slave is enslaved when up.
This happens because slave->link default init value
is 0, which is the same as BOND_LINK_UP, resulting
in bond_set_slave_link_state() ignoring this transition.
This patch sets the default value of slave->link to
BOND_LINK_NOCHANGE, assuring it will count as a state
transition and thus trigger notification logic.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8152 doesn't have U1U2 and U2P3 features, so use different
runtime functions for RTL812 and RTL8153 by adding autosuspend_en()
to rtl_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orig_ifinfo reference counter for last_bonding_candidate in
batadv_orig_node has to be reduced when an originator node is released.
Otherwise the orig_ifinfo is leaked and the reference counter the netdevice
is not reduced correctly.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The replacement of last_bonding_candidate in batadv_orig_node has to be an
atomic operation. Otherwise it is possible that the reference counter of a
batadv_orig_ifinfo is reduced which was no longer the
last_bonding_candidate when the new candidate is added. This can either
lead to an invalid memory access or to reference leaks which make it
impossible to an interface which was added to batman-adv.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The pointer batadv_bla_claim::backbone_gw can be changed at any time.
Therefore, access to it must be protected to ensure that two function
accessing the same backbone_gw are actually accessing the same. This is
especially important when the crc_lock is used or when the backbone_gw of a
claim is exchanged.
Not doing so leads to invalid memory access and/or reference leaks.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Fixes: 5a1dd8a477 ("batman-adv: lock crc access in bridge loop avoidance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_orig_node_new uses batadv_orig_node_vlan_new to allocate a new
batadv_orig_node_vlan and add it to batadv_orig_node::vlan_list. References
to this list have also to be cleaned when the batadv_orig_node is removed.
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
vlan_insert_tag can return NULL on errors. The distributed arp table code
therefore has to check the return value of vlan_insert_tag for NULL before
it can safely operate on this pointer.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
vlan_insert_tag can return NULL on errors. The bridge loop avoidance code
therefore has to check the return value of vlan_insert_tag for NULL before
it can safely operate on this pointer.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This solves the issue that a headphone is not working on the docking
unit.
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Tested-by: Alexander Klein <ALKL@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a788a4a040.
This patch is wrong, the type returned doesn't fit
what the error pointer macros expect.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is likely that checking 'fman->fifo_offset' instead of
'fman->cam_offset' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de>
Reported-by: Ralph Plawetzki <ralph@purejava.org>
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com>
Reported-by: Samo Ratnik <samo.ratnik@gmail.com>
Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>