Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Since gen_pool_dma_alloc() is introduced, we implement it to simplify code.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
On frv, the following errors happen:
drivers/media/platform/soc_camera/rcar_vin.c: In function 'rcar_vin_setup':
drivers/media/platform/soc_camera/rcar_vin.c:284:3: error: implicit declaration of function 'iowrite32' [-Werror=implicit-function-declaration]
drivers/media/platform/soc_camera/rcar_vin.c: In function 'rcar_vin_request_capture_stop':
drivers/media/platform/soc_camera/rcar_vin.c:353:2: error: implicit declaration of function 'ioread32' [-Werror=implicit-function-declaration]
This is because this driver forgot to include linux/io.h.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xycACgkQMUfUDdst+ymO+gCgxXdQXSU23i9ykc2CKBemdEBH
w6IAoKcokITcdN1IxxkfiMxOEld2hgZm
=3kbb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver update from Greg KH:
"Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported
issues"
* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
USB: Maintainers change for usb serial drivers
usb: usbtest: support container id descriptor test
usb: usbtest: support superspeed device capbility descriptor test
usb: usbtest: support usb2 extension descriptor test
usb: chipidea: only get vbus regulator for non-peripheral mode
USB: ehci-atmel: add usb_clk for transition to CCF
usb: cdc-wdm: ignore speed change notifications
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
usb: usbtest: support bos descriptor test for usb 3.0
USB: phy: samsung: Support multiple PHYs of same type
usb: wusbcore: change WA_SEGS_MAX to a legal value
usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
usb: wusbcore: combine multiple isoc frames in a single transfer request.
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
usb: chipidea: host: more enhancement when ci->hcd is NULL
usb: ohci: remove ep93xx bus glue platform driver
usb: usbtest: fix checkpatch warning as sizeof code style
UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
...
The code sequence:
isp->raw_dmamask = DMA_BIT_MASK(32);
isp->dev->dma_mask = &isp->raw_dmamask;
isp->dev->coherent_dma_mask = DMA_BIT_MASK(32);
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some non soc-camera drivers, e.g. em28xx, use subdevice drivers, originally
written for soc-camera, which use soc_camera_power_on() and
soc_camera_power_off() helpers to implement their .s_power() methods. Those
helpers in turn can enable and disable a clock, if it is supplied to them
as a parameter. This works well when camera host drivers balance their
calls to subdevices' .s_power() methods. However, some such drivers fail to
do that, which leads to unbalanced calls to v4l2_clk_enable() /
v4l2_clk_disable(), which then in turn produce kernel warnings. Such
behaviour is wrong and should be fixed, however, sometimes it is difficult,
because some of those drivers are rather old and use lots of subdevices,
which all should be tested after such a fix. To support such drivers this
patch adds a work-around, allowing host drivers or platforms to set a flag,
in which case soc-camera helpers will only enable the clock, if it is
disabled, and disable it only once on the first call to .s_power(0).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares soc-camera to use struct v4l2_subdev_platform_data for its
subdevice-facing API, which would allow subdevice driver re-use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a frame is still decoding when system enters suspend mode, we wait
on the device queue for a interrupt condition. This sometimes leads to a
timeout because the device queue might not be woken up everytime.
Usually, the context queue gets woken up when that context's frame gets
decoded. This patch adds a condition to wake up the device queue along
with the context queue when the system is in suspend mode.
Since the device queue is now woken up, we don't have to check the
context's int_cond flag while waiting. Also, we can skip calling try_run
after waking up the device queue to ensure that we don't have to wait
for more than one frame to be processed.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch sets the default values of MAX_QP and GOP size encoder
parameters to some firmware recommended default values. This enables
the applications to get a better encoded output using the default
settings itself.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Running the coda driver without CONFIG_SRAM selected leads to the following
probe error:
coda 63ff4000.vpu: iram pool not available
coda: probe of 63ff4000.vpu failed with error -12
In order to avoid it, select CONFIG_SRAM inside VIDEO_CODA.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If unused, the pixel format priv field has to be cleared by the driver
in try_fmt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement try_decoder_cmd to let userspace determine available commands
and flags.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes the v4l2-compliance "TRY_FMT(G_FMT) != G_FMT" issue.
The driver now overwrites invalid formats with the current setting, using
coda_get_max_dimensions to find device specific max width/height.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Moving the ioctl handler callbacks into the coda namespace helps
tremendously to make sense of backtraces.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[k.debski@samsung.com: fix whitespace error near coda_subscribe_event]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of copying v4l2_buf.flags from the source buffer, set
the destination buffer flags as reported by the hardware codec.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the product name (currently CodaDx6 or CODA7541)
to fill the v4l2_capabilities.name field.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register is only written on CodaDx6, so the temporary variable
to be written only needs to be initialized on CodaDx6. Also, drop
two no-op lines.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Allow device_run with no buffers queued after streamoff only when
the current instance is a decoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[k.debski@samsung.com: Add commit description]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With the new firmware, there are not anymore four register sets,
but a single register set, which the driver has to conserve across
context switches. This allows to handle more than four instances
at the same time.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the current context is running,
1] If release() or streamoff() is called on the current context,
it waits until the job is aborted or finished.
2] If the job is finished, driver will call the v4l2_m2m_job_finish().
3] If the job is aborted inside device_run callback, then driver
has to inform the v4l2 mem2mem framework about the same by calling
v4l2_m2m_job_finish() with VB2_BUF_STATE_ERROR.
The current code doesn't call v4l2_m2m_job_finish() in the case, where
the job is aborted from the device_run callback. This scenerio is
producing a hang as the other queued contexts are not getting scheduled.
By adding the ABORT state, driver can understand the current job
is aborted and not finished. By checking this flag, driver can call
v4l2_m2m_job_finish() with VB2_BUF_STATE_ERROR.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Avnd Kiran <avnd.kiran@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the de-interlacer block in VPE. For de-interlacer to
work, we need to enable 2 more sets of VPE input ports which fetch data
from the 'last' and 'last to last' fields of the interlaced video. Apart
from that, we need to enable the Motion vector output and input ports,
and also allocate DMA buffers for them.
We need to make sure that two most recent fields in the source queue are
available and in the 'READY' state. Once a mem2mem context gets access
to the VPE HW(in device_run), it extracts the addresses of the 3
buffers, and provides it to the data descriptors for the 3 sets of input
ports((LUMA1, CHROMA1), (LUMA2, CHROMA2), and (LUMA3, CHROMA3))
respectively for the 3 consecutive fields. The motion vector and output
port descriptors are configured and the list is submitted to VPDMA.
Once the transaction is done, the v4l2 buffer corresponding to the
oldest field(the 3rd one) is changed to the state 'DONE', and the
buffers corresponding to 1st and 2nd fields become the 2nd and 3rd field
for the next de-interlace operation. This way, for each deinterlace
operation, we have the 3 most recent fields. After each transaction, we
also swap the motion vector buffers, the new input motion vector buffer
contains the resultant motion information of all the previous frames,
and the new output motion vector buffer will be used to hold the updated
motion vector to capture the motion changes in the next field. The
motion vector buffers are allocated using the DMA allocation API.
The de-interlacer is removed from bypass mode, it requires some extra
default configurations which are now added. The chrominance upsampler
coefficients are added for interlaced frames. Some VPDMA parameters like
frame start event and line mode are configured for the 2 extra sets of
input ports.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE is a block which consists of a single memory to memory path which
can perform chrominance up/down sampling, de-interlacing, scaling, and
color space conversion of raster or tiled YUV420 coplanar, YUV422
coplanar or YUV422 interleaved video formats.
We create a mem2mem driver based primarily on the mem2mem-testdev
example. The de-interlacer, scaler and color space converter are all
bypassed for now to keep the driver simple. Chroma up/down sampler
blocks are implemented, so conversion beteen different YUV formats is
possible.
Each mem2mem context allocates a buffer for VPE MMR values which it will
use when it gets access to the VPE HW via the mem2mem queue, it also
allocates a VPDMA descriptor list to which configuration and data
descriptors are added.
Based on the information received via v4l2 ioctls for the source and
destination queues, the driver configures the values for the MMRs, and
stores them in the buffer. There are also some VPDMA parameters like
frame start and line mode which needs to be configured, these are
configured by direct register writes via the VPDMA helper functions.
The driver's device_run() mem2mem op will add each descriptor based on
how the source and destination queues are set up for the given ctx, once
the list is prepared, it's submitted to VPDMA, these descriptors when
parsed by VPDMA will upload MMR registers, start DMA of video buffers on
the various input and output clients/ports.
When the list is parsed completely(and the DMAs on all the output ports
done), an interrupt is generated which we use to notify that the source
and destination buffers are done. The rest of the driver is quite
similar to other mem2mem drivers, we use the multiplane v4l2 ioctls as
the HW support coplanar formats.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Create functions which the VPE driver can use to create a VPDMA
descriptor and add it to a VPDMA descriptor list. These functions take a
pointer to an existing list, and append the configuration/data/control
descriptor header to the list.
In the case of configuration descriptors, the creation of a payload
block may be required(the payloads can hold VPE MMR values, or scaler
coefficients). The allocation of the payload buffer and it's content is
left to the VPE driver. However, the VPDMA library provides helper
macros to create payload in the correct format.
Add debug functions to dump the descriptors in a way such that it's easy
to see the values of different fields in the descriptors.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The primary function of VPDMA is to move data between external memory
and internal processing modules(in our case, VPE) that source or sink
data. VPDMA is capable of buffering this data and then delivering the
data as demanded to the modules as programmed. The modules that source
or sink data are referred to as clients or ports. A channel is setup
inside the VPDMA to connect a specific memory buffer to a specific
client. The VPDMA centralizes the DMA control functions and buffering
required to allow all the clients to minimize the effect of long latency
times.
Add the following to the VPDMA helper:
- A data struct which describe VPDMA channels. For now, these channels
are the ones used only by VPE, the list of channels will increase when
VIP(Video Input Port) also uses the VPDMA library. This channel
information will be used to populate fields required by data
descriptors.
- Data structs which describe the different data types supported by
VPDMA. This data type information will be used to populate fields
required by data descriptors and used by the VPE driver to map a V4L2
format to the corresponding VPDMA data type.
- Provide VPDMA register offset definitions, functions to read, write
and modify VPDMA registers.
- Functions to create and submit a VPDMA list. A list is a group of
descriptors that makes up a set of DMA transfers that need to be
completed. Each descriptor will either perform a DMA transaction to
fetch input buffers and write to output buffers(data descriptors), or
configure the MMRs of sub blocks of VPE(configuration descriptors), or
provide control information to VPDMA (control descriptors).
- Functions to allocate, map and unmap buffers needed for the descriptor
list, payloads containing MMR values and scaler coefficients. These use
the DMA mapping APIs to ensure exclusive access to VPDMA.
- Functions to enable VPDMA interrupts. VPDMA can trigger an interrupt
on the VPE interrupt line when a descriptor list is parsed completely
and the DMA transactions are completed. This requires masking the events
in VPDMA registers and configuring some top level VPE interrupt
registers.
- Enable some VPDMA specific parameters: frame start event(when to start
DMA for a client) and line mode(whether each line fetched should be
mirrored or not).
- Function to load firmware required by VPDMA. VPDMA requires a firmware
for it's internal list manager. We add the required request_firmware
apis to fetch this firmware from user space.
- Function to dump VPDMA registers.
- A function to initialize and create a VPDMA instance, this will be
called by the VPE driver with it's platform device pointer, this
function will take care of loading VPDMA firmware and returning a
vpdma_data instance back to the VPE driver. The VIP driver will also
call the same init function to initialize it's own VPDMA instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
irq allocated with devm_request_irq should not be freed using
free_irq, because doing so causes a dangling pointer, and a
subsequent double free.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the generic PHY API instead of the platform callback
to control the MIPI CSIS DPHY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Since CONFIG_PLAT_S3C64XX is going to be removed, this patch modifies
the Kconfig entry of s3c-camif driver to use the proper way of checking
for S3C64xx support - CONFIG_ARCH_S3C64XX.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch proposes to remove the IRQF_DISABLED flag from
davinci media platform drivers.
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If NO_DMA=y:
warning: (... && VIDEO_RENESAS_VSP1 && ...) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:202: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:385: error: implicit declaration of function ‘dma_get_sgtable’
make[7]: *** [drivers/media/v4l2-core/videobuf2-dma-contig.o] Error 1
VIDEO_RENESAS_VSP1 (which doesn't have a platform dependency) selects
VIDEOBUF2_DMA_CONTIG, but the latter depends on HAS_DMA.
Make VIDEO_RENESAS_VSP1 depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the private struct vb2_dma_sg_desc with the struct sg_table so
we can benefit from all the helping functions in lib/scatterlist.c for
things like allocating the sg or compacting the descriptor.
marvel-ccic and solo6x10 drivers, that use this API have been updated.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[s.nawrocki@samsung.com: minor corrections of the changelog]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes regression introduced in commit 5c77879ff9
"[media] v4l2-dev: add new VFL_DIR_ defines" caused by not initializing
the vfl_dir field of the vfd_decoder instance of struct video_device,
after the field was introduced. It precluded calling the driver's ioctls
which require vfl_dir not to be equal to VFL_DIR_RX which is defined as
0 and uninitialized vfl_dir field is interpreted as such. In effect the
test in the v4l_s_fmt function failed for the ioctls that expect is_tx
to be false, which prevented the ioctl callbacks registered by the driver
from being called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Smatch complains about the locking here because we mix spin_lock_irq()
with spin_lock_irqsave() in an unusual way. According to Smatch, it's
not always clear if the IRQs are enabled or disabled when we return. It
turns out this function is always called with IRQs enabled and we can
just use spin_lock_irq().
It's called from __enqueue_in_driver().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "i < " part of the "i < ARRAY_SIZE()" condition was missing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[g.liakhovetski@gmx.de: remove unrelated superfluous braces]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- OF and ACPI helpers are now included in the core, and not in
external files anymore. This removes dependency problems for
modules and is cleaner, in general.
- mv64xxx-driver gains fifo usage to support mv78230
- imx-driver overhaul to support VF610
- various cleanups, most notably related to devm_* and CONFIG_PM
usage
- driver bugfixes and smaller feature additions"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: rcar: add rcar-H2 support
i2c: sirf: retry 3 times as sometimes we get random noack and timeout
i2c: sirf: support reverse direction of address
i2c: sirf: fix the typo for setting bitrate to less than 100k
i2c: sirf: we need to wait I2C_RESET status in resume
i2c: sirf: reset i2c controller early after we get a noack
i2c: designware: get SDA hold time, HCNT and LCNT configuration from ACPI
i2c: designware: make HCNT/LCNT values configurable
i2c: mpc: cleanup clock API use
i2c: pnx: fix error return code in i2c_pnx_probe()
i2c: ismt: add error return code in probe()
i2c: mv64xxx: fix typo in binding documentation
i2c: imx: use exact SoC revision to document binding
i2c: move ACPI helpers into the core
i2c: move OF helpers into the core
i2c: mv64xxx: Fix timing issue on Armada XP (errata FE-8471889)
i2c: mv64xxx: Add I2C Transaction Generator support
i2c: powermac: fix return path on error
Documentation: i2c: Fix example in instantiating-devices
i2c: tiny-usb: do not use stack as URB transfer_buffer
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Gscaler video device registration was happening without reference to
a parent v4l2_dev causing probe to fail. The patch creates a parent
v4l2 device and uses it for the gsc m2m video device registration.
This fixes regression introduced with comit commit 1c1d86a1ea
[media] v4l2: always require v4l2_dev, rename parent to dev_parent
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
The 10-bit and 12-bit Bayer output formats supported by FIMC-LITE
actually use 16 bits where the extra bits are padded with zeros.
The patch corrects buffer allocation for these two formats by
modifying the depth field. This prevents memory corruption by the
output DMA due to insufficient buffer size.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Commit 1c1d86a1ea ("[media] v4l2: always require v4l2_dev,
rename parent to dev_parent") expects v4l2_dev to be always set.
It converted most of the drivers using the parent field of video_device
to v4l2_dev field. G2D driver did not set the parent field. Hence it got
left out. Without this patch we get the following boot warning and G2D
driver fails to register the video device.
WARNING: CPU: 0 PID: 1 at drivers/media/v4l2-core/v4l2-dev.c:775 __video_register_device+0xfc0/0x1028()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.11.0-rc1-00001-g1c3e372-dirty #9
[<c0014b7c>] (unwind_backtrace+0x0/0xf4) from [<c0011524>] (show_stack+0x10/0x14)
[<c0011524>] (show_stack+0x10/0x14) from [<c041d7a8>] (dump_stack+0x7c/0xb0)
[<c041d7a8>] (dump_stack+0x7c/0xb0) from [<c001dc94>] (warn_slowpath_common+0x6c/0x88)
[<c001dc94>] (warn_slowpath_common+0x6c/0x88) from [<c001dd4c>] (warn_slowpath_null+0x1c/0x24)
[<c001dd4c>] (warn_slowpath_null+0x1c/0x24) from [<c02cf8d4>] (__video_register_device+0xfc0/0x1028)
[<c02cf8d4>] (__video_register_device+0xfc0/0x1028) from [<c0311a94>] (g2d_probe+0x1f8/0x398)
[<c0311a94>] (g2d_probe+0x1f8/0x398) from [<c0247d54>] (platform_drv_probe+0x14/0x18)
[<c0247d54>] (platform_drv_probe+0x14/0x18) from [<c0246b10>] (driver_probe_device+0x108/0x220)
[<c0246b10>] (driver_probe_device+0x108/0x220) from [<c0246cf8>] (__driver_attach+0x8c/0x90)
[<c0246cf8>] (__driver_attach+0x8c/0x90) from [<c0245050>] (bus_for_each_dev+0x60/0x94)
[<c0245050>] (bus_for_each_dev+0x60/0x94) from [<c02462c8>] (bus_add_driver+0x1c0/0x24c)
[<c02462c8>] (bus_add_driver+0x1c0/0x24c) from [<c02472d0>] (driver_register+0x78/0x140)
[<c02472d0>] (driver_register+0x78/0x140) from [<c00087c8>] (do_one_initcall+0xf8/0x144)
[<c00087c8>] (do_one_initcall+0xf8/0x144) from [<c05b29e8>] (kernel_init_freeable+0x13c/0x1d8)
[<c05b29e8>] (kernel_init_freeable+0x13c/0x1d8) from [<c041a108>] (kernel_init+0xc/0x160)
[<c041a108>] (kernel_init+0xc/0x160) from [<c000e2f8>] (ret_from_fork+0x14/0x3c)
---[ end trace 4e0ec028b0028e02 ]---
s5p-g2d 12800000.g2d: Failed to register video device
s5p-g2d: probe of 12800000.g2d failed with error -22
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
The data pointer should point to DT data, and not to the ID
array.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
The video encode/decode paths have duplicated logic between
VIDIOC_TRY_FMT and VIDIOC_S_FMT that should be de-duped. Also, video
decode reports V4L2_PIX_FMT_NV12MT_16X16 output format, regardless of
what the actual output has been set at. Fix this.
Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
A mutex_lock() was left when the driver was converted to use the vb2
ioctl helpers, resulting in a deadlock at streamon time. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSPR and VSPS instances use two clocks, the VSP1 system clock and
the VSP1 realtime clock. Both of them need to be enabled to access the
VSP1 registers.
Add support for an optional RT clock and enable/disable it along with
the system clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill bus_info with the VSP1 platform device name
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.
Introduced by commit 873229e4fd
([media] media: davinci: vpif: capture: add V4L2-async support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.
Introduce by commit 4b8a531e6b.
([media] media: davinci: vpif: display: add V4L2-async support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by: kbuild test robot <fengguang.wu@intel.com>:
drivers/media/platform/vsp1/vsp1_drv.c:434:21: sparse: cast removes address space of expression
433 vsp1->mmio = devm_ioremap_resource(&pdev->dev, io);
> 434 if (IS_ERR((void *)vsp1->mmio))
> 435 return PTR_ERR((void *)vsp1->mmio);
There's no need to convert it to void *.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Because "i" is unsigned then "i-- >= 0" is always true. If we don't
find what we are looking for then we loop forever.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Include the v4l2-dv-timings.h header file which in the s5p-tv driver which
was supposed to be updated in commit 2576415846
"[media] v4l2: move dv-timings related code to v4l2-dv-timings.c"
This fixes following build error:
drivers/media/platform/s5p-tv/hdmi_drv.c: In function ‘hdmi_s_dv_timings’:
drivers/media/platform/s5p-tv/hdmi_drv.c:628:3: error: implicit declaration of function ‘v4l_match_dv_timings’
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is a stray '!' character so the error message never gets printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
__is_set_init_isp_aa and fimc_is_hw_set_tune currently do not have
any callers. However these functions may be used in the future. Hence
instead of deleting them, staticize and annotate them with __maybe_unused
flag to avoid compiler warnings.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use clk_prepare_enable()/clk_disable_unprepare() instead of
separately prearing/unparing the clk_cam clocks. This simplifies
the code that is now mostly not going to be used, function
__fimc_md_set_camclk() is only left for S5PV210 platform which
is not yet converted to Device Tree.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set the subdevs owner module so the exynos4_fimc_is module cannot
be unloaded when the FIMC-IS driver is in use.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the same callbacks are used for runtime and system suspend/resume,
clocks can get disabled twice, which can lead to negative reference
counts and kernel warnings.
This patch splits suspend/resume callbacks into separate runtime and
system-wide functions, so clock gating is done correctly.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's the only function in v4l2-dv-timings.c with the v4l prefix instead
of v4l2. Make it consistent with the other functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When using devm_ioremap_resource(), we do not need to check the return value of
platform_get_resource(), so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some resources were not being released in the error path and some were released
in the incorrect order.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
use devm_clk_get() for automatic put after device close, check for and
propagate errors when enabling clocks, need to prepare clocks before
they can get enabled, adjust code paths to correctly balance get/put and
prepare/unprepare and enable/disable calls
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If NO_DMA=y:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:204: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function ‘dma_get_sgtable’
Commit da508f5799 ("[media] media/v4l2:
VIDEOBUF2_DMA_CONTIG should depend on HAS_DMA") added a dependency on
HAS_DMA to VIDEO_SH_VEU, as it selects VIDEOBUF2_DMA_CONTIG.
However, this got lost in the merge conflict resolution in commit
df90e22589 ("Merge branch 'devel-for-v3.10'
into v4l_for_linus").
Re-add the dependency to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/platform/soc_camera/sh_mobile_ceu_camera.c: In function 'sh_mobile_ceu_clock_start':
drivers/media/platform/soc_camera/sh_mobile_ceu_camera.c:613:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When gsc is in runtime suspended state, there is no need to call
m2m_suspend during suspend and similarly, there is no need to call
m2m_resume during resume if already in runtime suspended state. This
patch adds the necessary conditions to achieve this.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
__fimc_is_hw_update_param is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dev->of_node could be NULL. Hence check for the same and return before
dereferencing it in the subsequent error message.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The soc-camera core does all the work on supporting asynchronous
subdevice probing, host drivers only have to pass a subdevice list to
soc-camera. Typically this list is provided by the platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_MBUS_FMT_* codes are defined in v4l2-mediabus.h as hexadecimal
constants. Print them in the same form for easier recognition.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use devm_* resource allocators to simplify the driver's probe and clean up
paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With synchronous subdevice probing regulators should be requested by the
soc-camera core in soc_camera_pdrv_probe(). Subdevice drivers, supporting
asynchronous probing, call soc_camera_power_init() to request regulators.
Erroneously, the same regulator array is used in the latter case as in
the former, which leads to a failure. This patch fixes it by preventing
the second regulator request from being executed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
media_build/v4l/soc_camera.c: In function 'soc_camera_host_register':
media_build/v4l/soc_camera.c:1513:10: warning: 'sasd' may be used uninitialized in this function [-Wmaybe-uninitialized]
snprintf(clk_name, sizeof(clk_name), "%d-%04x",
^
media_build/v4l/soc_camera.c:1464:34: note: 'sasd' was declared here
struct soc_camera_async_subdev *sasd;
^
By changing the type of 'i' to unsigned and changing a condition we finally
convince the compiler that sasd is really initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add Renesas R-Car VIN (Video In) V4L2 driver.
Based on the patch by Phil Edworthy <phil.edworthy@renesas.com>.
[Sergei: removed deprecated IRQF_DISABLED flag, reordered/renamed 'enum chip_id'
values, reordered rcar_vin_id_table[] entries, removed senseless parens from
to_buf_list() macro, used ALIGN() macro in rcar_vin_setup(), added {} to the
*if* statement and used 'bool' values instead of 0/1 where necessary, removed
unused macros, done some reformatting and clarified some comments.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new blanking and frame size defines. This also fixed a bug in
these drivers: they assumed that the height for interlaced formats was
the field height, however height is the frame height. So the height
for a field is actually bt->height / 2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new defines to calculate the full blanking and frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 driver allows to define the maximum number of each module
such as RPF, WPF, and UDS in a platform data definition.
This suppresses operations for nonexistent or unused modules.
Signed-off-by: Katsuya Matsubara <matsu@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Each source entity maintains a pointer to the counterpart sink
entity while an enabled link connects them. It should be managed by
the setup_link callback in the media controller framework at runtime.
However, enabled links which connect RPFs and WPFs that have an
equivalent index number are created during initialization.
This registers the pointer to a sink entity from the source entity
when an enabled link is created.
Signed-off-by: Katsuya Matsubara <matsu@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 is a video processing engine that includes a blender, scalers,
filters and statistics computation. Configurable data path routing logic
allows ordering the internal blocks in a flexible way.
Due to the configurable nature of the pipeline the driver implements the
media controller API and doesn't use the V4L2 mem-to-mem framework, even
though the device usually operates in memory to memory mode.
Only the read pixel formatters, up/down scalers, write pixel formatters
and LCDC interface are supported at this stage.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
MFC v7 supports VP8 encoding and this patch adds support
for it in the driver.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Firmware version v7 is mostly similar to v6 in terms
of hardware specific controls and commands. So the hardware
specific opr_v6 and cmd_v6 are re-used for v7 also. This patch
updates the v6 files to handle v7 version also.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds variant data and core support for the MFC v7 firmware
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch adds the register definition file for new firmware
version v7 for MFC. New firmware supports VP8 encoding along with
many other features.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The MFC v6 specific code holds good for MFC v7 also as
the v7 version is a superset of v6 and the HW interface
remains more or less similar. This patch renames the macro
IS_MFCV6() to IS_MFCV6_PLUS() so that it can be used
for v7 also.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch updates few encoder buffer sizes for MFC v6.5
as per the udpdated user manual. The same buffer sizes
holds good for v7 firmware also.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes (em28xx, coda, usbtv, s5p, hdpvr and ml86v7667) and
a fix for media DocBook"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: fix dependency
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
This patch enables decoding of h.264 and mpeg4 streams on CODA7541.
Queued output buffers are immediately copied into the bitstream
ringbuffer. A device_run can be scheduled whenever there is either
enough compressed bitstream data, or the CODA is in stream end mode.
Each successful device_run, data is read from the bitstream ringbuffer
and a frame is decoded into a free internal framebuffer. Depending on
reordering, a possibly previously decoded frame is marked as display
frame, and at the same time the display frame from the previous run
is copied out into a capture buffer by the rotator hardware.
The dequeued capture buffers are counted to send the EOS signal to
userspace with the last frame. When userspace sends the decoder stop
command or enqueues an empty output buffer, the stream end flag is
set to allow decoding the remaining frames in the bitstream
ringbuffer.
The enum_fmt/try_fmt functions return fixed capture buffer sizes
while the output queue is streaming, to allow better autonegotiation
in userspace.
A per-context buffer mutex is used to lock the picture run against
buffer dequeueing: if a job gets queued, then streamoff dequeues
the last buffer, and then device_run is called, bail out. For that
the interrupt handler has to be threaded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add coda_prepare_encode() and coda_finish_encode() functions. They are called
from coda_device_run() and coda_irq_handler(), respectively, before and after
the hardware picture run. This should make the following decoder support patch
easier to read, which will add the coda_prepare/finish_decode() equivalents.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This sets up IRAM areas used as temporary memory for the different
hardware units depending on the frame size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is a purely cosmetic change. Since the 'subdev' member
points to an array of subdevs make it more explicit by
renaming to the plural form.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
enum v4l2_async_bus_type also selects a method subdevs are matched
in the notification handlers, rename it to v4l2_async_match_type
so V4L2_ASYNC_MATCH_OF entry can be further added for matching by
device tree node pointer.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch switchs to resource managed allocation and request in mmp-driver.
It can remove free resource operations.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the SOFx/EOFx pair check for marvell-ccic.
When switching format, the last EOF may not arrive when stop streamning.
And the EOF will be detected in the next start streaming.
Must ensure clear the left over frame flags before every really start streaming.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds some planar formats support for marvell-ccic.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch refines mcam_set_contig_buffer() in mcam core.
It can remove redundant code line and enhance readability.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the reset ccic phy operation when stop streaming.
Stop streaming without reset ccic phy, the next start streaming
may be unstable.
Also need add CCIC2 definition when PXA688/PXA2128 support dual ccics.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the clock tree support for marvell-ccic.
Signed-off-by: Libin Yang <lbyang@marvell.com>
Signed-off-by: Albert Wang <twang13@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the MIPI support for marvell-ccic.
Board driver should determine whether using MIPI or not.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a bitstream ringbuffer using kfifo. Queued source buffers are to be copied
into the bitstream ringbuffer immediately and marked as done, if possible.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch splits the global workbuf into a global tempbuf and a per-context
workbuf, adds the codec mode aux register, and restores the work buffer
pointer on commands. With the new firmware, there is only a single set of
read/write pointers which need to be restored between context switches.
This allows more than four active contexts at the same time.
All auxiliary buffers are now allocated through a helper function to avoid
code duplication.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The encoder only ever needs two buffers, but we'll have to increase
CODA_MAX_FRAMEBUFFERS for the decoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This sets up IRAM areas used as temporary memory for the different
hardware units depending on the frame size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As stated in the vb2_buffer documentation, drivers should not directly fill
in v4l2_planes[0].bytesused, but should use the vb2_set_plane_payload()
function instead. No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 1c1d86a1ea ("[media] v4l2: always require v4l2_dev,
rename parent to dev_parent") expects v4l2_dev to be always set.
It converted most of the drivers using the parent field of video_device
to v4l2_dev field. G2D driver did not set the parent field. Hence it got
left out. Without this patch we get the following boot warning and G2D
driver fails to register the video device.
WARNING: CPU: 0 PID: 1 at drivers/media/v4l2-core/v4l2-dev.c:775 __video_register_device+0xfc0/0x1028()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.11.0-rc1-00001-g1c3e372-dirty #9
[<c0014b7c>] (unwind_backtrace+0x0/0xf4) from [<c0011524>] (show_stack+0x10/0x14)
[<c0011524>] (show_stack+0x10/0x14) from [<c041d7a8>] (dump_stack+0x7c/0xb0)
[<c041d7a8>] (dump_stack+0x7c/0xb0) from [<c001dc94>] (warn_slowpath_common+0x6c/0x88)
[<c001dc94>] (warn_slowpath_common+0x6c/0x88) from [<c001dd4c>] (warn_slowpath_null+0x1c/0x24)
[<c001dd4c>] (warn_slowpath_null+0x1c/0x24) from [<c02cf8d4>] (__video_register_device+0xfc0/0x1028)
[<c02cf8d4>] (__video_register_device+0xfc0/0x1028) from [<c0311a94>] (g2d_probe+0x1f8/0x398)
[<c0311a94>] (g2d_probe+0x1f8/0x398) from [<c0247d54>] (platform_drv_probe+0x14/0x18)
[<c0247d54>] (platform_drv_probe+0x14/0x18) from [<c0246b10>] (driver_probe_device+0x108/0x220)
[<c0246b10>] (driver_probe_device+0x108/0x220) from [<c0246cf8>] (__driver_attach+0x8c/0x90)
[<c0246cf8>] (__driver_attach+0x8c/0x90) from [<c0245050>] (bus_for_each_dev+0x60/0x94)
[<c0245050>] (bus_for_each_dev+0x60/0x94) from [<c02462c8>] (bus_add_driver+0x1c0/0x24c)
[<c02462c8>] (bus_add_driver+0x1c0/0x24c) from [<c02472d0>] (driver_register+0x78/0x140)
[<c02472d0>] (driver_register+0x78/0x140) from [<c00087c8>] (do_one_initcall+0xf8/0x144)
[<c00087c8>] (do_one_initcall+0xf8/0x144) from [<c05b29e8>] (kernel_init_freeable+0x13c/0x1d8)
[<c05b29e8>] (kernel_init_freeable+0x13c/0x1d8) from [<c041a108>] (kernel_init+0xc/0x160)
[<c041a108>] (kernel_init+0xc/0x160) from [<c000e2f8>] (ret_from_fork+0x14/0x3c)
---[ end trace 4e0ec028b0028e02 ]---
s5p-g2d 12800000.g2d: Failed to register video device
s5p-g2d: probe of 12800000.g2d failed with error -22
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The data pointer should point to DT data, and not to the ID
array.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video encode/decode paths have duplicated logic between
VIDIOC_TRY_FMT and VIDIOC_S_FMT that should be de-duped. Also, video
decode reports V4L2_PIX_FMT_NV12MT_16X16 output format, regardless of
what the actual output has been set at. Fix this.
Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PTR_RET is now deprecated. Use PTR_ERR_OR_ZERO instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull "exotic" arch fixes from Geert Uytterhoeven:
"This is a collection of several exotic architecture fixes, and a few
other fixes for issues that were detected while doing the former"
* 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (35 commits)
lib: Move fonts from drivers/video/console/ to lib/fonts/
console/font: Refactor font support code selection logic
Revert "staging/solo6x10: depend on CONFIG_FONTS"
input: cros_ec_keyb_clear_keyboard() depends on CONFIG_PM_SLEEP
score: Wire up asm-generic/xor.h
score: Remove unneeded <asm/dma-mapping.h>
openrisc: Wire up asm-generic/xor.h
h8300/boot: Use POSIX "$((..))" instead of bashism "$[...]"
h8300: Mark H83002 and H83048 CPU support broken
h8300: Switch h8300 to drivers/Kconfig
h8300: Limit timer channel ranges in Kconfig
h8300: Wire up asm-generic/xor.h
h8300: Fill the system call table using a CALL() macro
h8300: Fix <asm/tlb.h>
h8300: Hardcode symbol prefixes in asm sources
h8300: add missing definition for read_barries_depends()
frv: head.S - Remove commented-out initialization code
cris: Wire up asm-generic/vga.h
parport: disable PC-style parallel port support on cris
console: Disable VGA text console support on cris
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
Ensure the colorspace is properly adjusted by the driver for YUV
and Bayer image formats. The subdev try_fmt helper is simplified.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure there are valid initial image formats on the FIMC.n subdev pads.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure there is a valid initial resolution and pixel format set
at the FIMC-IS-ISP subdev pads.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure TRY formats are propagated from the sink pad to the source pads
of the FIMC-IS-ISP subdev and the TRY and ACTIVE formats are separated.
[mchehab@redhat.com: Whitespace cleanup]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure the image resolution and crop rectangle on the FIMC-LITE.n
subdevs and fimc-lite.n.capture video nodes is properly configured
upon the driver's initialization.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIMC-LITE subdevs have one sink pad and two source pads on which the image
formats are always same. This patch implements missing format propagation
from the sink pad to the source pads, to allow user space to negotiate TRY
format on whole media pipeline involving FIMC-LITE.n subdevs. The subdev
try_fmt helper is simplified.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes the firmware file names of the FIMC-IS subsystem.
It is needed since there are different firmwares used across various
SoC series, e.g. Exynos4 and Exynos5.
Also the sensor specific "setfile" name is changed, to account for
it depends on an image sensor and is also specific to the FIMC-IS
and the SoC.
This is a change for a driver merged in 3.10.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add compatible property for the Exynos5250 and enable the frame start
and frame end interrupts. These interrupts are needed for the Exynos5
FIMC-IS firmware. The driver enables those interrupt only where available,
depending on the 'compatible' property. This can be optimized further,
by exposing some API at the subdev driver, so the host driver can enable
extra interrupts only for the image processing chains involving FIMC-IS.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the Exynos5250 SoC variant of the FIMC-LITE
IP. A 'compatible' string is added for Exynos5250 compatible devices
and the capture DMA handling is reworked to use the FLITE_REG_CIFCNTSEQ
register, masking output DMA buffer address slots. The frame interrupt
is enabled so there are now 2 interrupts per frame. This likely can be
optimized in future by using any status registers that allow to figure
out what the last and the currently written frame buffer is. It would
also be more reliable in cases where there are high interrupt service
latencies.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FIMC-LITE IP block is available only on platforms instantiated
from device tree.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The m2m-deinterlace, mem2mem_testdev and mx2_emmaprp drivers didn't set
the v4l2_dev pointer in struct video_device, even though a v4l2_device was
registered correctly. These days this v4l2_dev pointer must be set correctly,
so this patch adds that for these three drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
media-git/drivers/media/platform/omap/omap_vout.c: In function ‘omapvid_init’:
media-git/drivers/media/platform/omap/omap_vout.c:382:17: warning: ‘mode’ may be used uninitialized in this function [-Wmaybe-uninitialized]
vout->dss_mode = video_mode_to_dss_mode(vout);
^
media-git/drivers/media/platform/omap/omap_vout.c:332:23: note: ‘mode’ was declared here
enum omap_color_mode mode;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.lad@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
media-git/drivers/media/platform/blackfin/bfin_capture.c: In function ‘bcap_probe’:
media-git/drivers/media/platform/blackfin/bfin_capture.c:1007:16: warning: ignoring return value of ‘vb2_queue_init’, declared with attribute warn_unused_result [-Wunused-result]
vb2_queue_init(q);
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The scaling / cropping library, that has been extracted from the CEU
driver still contained a couple of references to the original hardware.
Clean them up.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sh_mobile_ceu_camera driver implements a generic algorithm for setting
up an optimal client and host scaling and cropping configuration. This
patch makes those functions available for all drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several functions in the sh_mobile_ceu_camera driver implement generic
algorithms and can be re-used by other V4L2 camera host drivers too. These
functions attempt to optimise scaling and cropping functions of the
subdevice, e.g. a camera sensor. This patch makes those functions generic
for future re-use by other camera host drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In scan_async_group() if the size parameter is negative, the sasd pointer
will be used uninitialised:
drivers/media/platform/soc_camera/soc_camera.c: In function "soc_camera_host_register":
drivers/media/platform/soc_camera/soc_camera.c:1514:55: warning: "sasd" may
be used uninitialized in this function [-Wmaybe-uninitialized]
sasd->asd.match.i2c.adapter_id, sasd->asd.match.i2c.address);
^
drivers/media/platform/soc_camera/soc_camera.c:1464:34: note: "sasd" was
declared here
struct soc_camera_async_subdev *sasd;
Fix this by making "size" and the array, from which it is assigned unsigned.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current Makefile rules to build font support are messy and buggy.
Replace them by Kconfig rules:
- Introduce CONFIG_FONT_SUPPORT, which controls the building of all font
code,
- Select CONFIG_FONT_SUPPORT for all drivers that use fonts,
- Select CONFIG_FONT_8x16 for all drivers that default to the VGA8x16
font,
- Drop the bogus console dependency for CONFIG_VIDEO_VIVI,
- Always process drivers/video/console/Makefile, as some drivers need
fonts even if CONFIG_VT is not set.
This fixes (if CONFIG_SOLO6X10=y and there are no built-in console
drivers):
drivers/built-in.o: In function `solo_osd_print':
drivers/staging/media/solo6x10/solo6x10-enc.c:144: undefined reference to `.find_font'
This fixes (if CONFIG_VT=n):
drivers/built-in.o: In function `vivi_init':
vivi.c:(.init.text+0x1a3da): undefined reference to `find_font'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> [original part]
Acked-by: Randy Dunlap <rdunlap@infradead.org> [drivers/video/Makefile]
Pull media fixes from Mauro Carvalho Chehab:
"Another set of fixes for Kernel 3.10.
This series contain:
- two Kbuild fixes for randconfig
- a buffer overflow when using rtl28xuu with r820t tuner
- one clk fixup on exynos4-is driver"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Fix build when drivers are builtin and frontend modules
[media] s5p makefiles: don't override other selections on obj-[ym]
[media] exynos4-is: Fix FIMC-IS clocks initialization
[media] rtl28xxu: fix buffer overflow when probing Rafael Micro r820t tuner
Use the v4l2-async API to support asynchronous subdevice probing,
including the CSI2 subdevice. Synchronous probing is still supported too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms. The selected approach adds a
notifier for each struct soc_camera_device instance, i.e. for each video
device node, even when there are multiple such instances registered with a
single soc-camera host simultaneously.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of centrally enabling and disabling subdevice master clocks in
soc-camera core, let subdevice drivers do that themselves, using the
V4L2 clock API and soc-camera convenience wrappers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some CEU implementations have non-standard (larger) maximum supported
width and height values. Add two OF properties to specify them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an OF hook to sh_mobile_ceu_camera.c, no properties so far. Booting
with DT also requires platform data to be optional.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During client probing we only have to turn on the host's clock, no need to
actually attach the client to the host.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All existing soc-camera host drivers use .clock_start() and .clock_stop()
callbacks to activate and deactivate their camera interfaces, whereas
.add() and .remove() callbacks are usually dummy. Make the former two
compulsory and the latter two optional.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the sh-mobile-ceu-camera driver activates
and, respectively, deactivates its camera interface and, if necessary, the
CSI2 controller. Only handling of the CSI2 interface is client-specific and
is only needed, when a data-exchange with the client is taking place. Move
the rest to .clock_start() and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the mx1-camera driver only activates
and deactivates its camera interface respectively, which doesn't include
any client-specific actions. Move this functionality into .clock_start()
and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the mx2-camera driver only activates
and deactivates its camera interface respectively, which doesn't include
any client-specific actions. Move this functionality into .clock_start()
and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the mx3-camera driver only activates
and deactivates its camera interface respectively, which doesn't include
any client-specific actions. Move this functionality into .clock_start()
and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the atmel-isi camera host driver only
activates and deactivates its camera interface respectively, which doesn't
include any client-specific actions. Move this functionality into
.clock_start() and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the omap1-camera driver only activates
and deactivates its camera interface respectively, which doesn't include
any client-specific actions. Move this functionality into .clock_start()
and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding and removing a client, the pxa-camera driver only activates
and deactivates its camera interface respectively, which doesn't include
any client-specific actions. Move this functionality into .clock_start()
and .clock_stop() callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera uses a single camera host callback to activate the
interface master clock and to configure the interface for a specific
client. However, during probing we might not have the information about
a client, we just need to activate the clock. Add new camera host driver
callbacks to only start and stop the clock without and client-specific
configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All soc-camera host drivers include a pointer to an soc-camera device in
their host private struct to check, that only one client is connected.
Move this common code to soc_camera.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc-camera isn't sufficiently broken to include any files from the
drivers/media/i2c/soc_camera directory in its core or host driver files:-)
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
[g.liakhovetski@gmx.de: further simplified return statement]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The last users of Kconfig symbols MX3_VIDEO and VIDEO_MX2_HOSTSUPPORT
were removed in v3.2. Their Kconfig entries can be removed now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For vpif display driver each IRQ resource contains a single IRQ
so drop the second loop.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ideally the freeing of irq's and the global variables needs to be
done in the remove() rather than module_exit(), this patch moves
the freeing up of irq's and freeing the memory allocated to channel
objects to remove() callback of struct platform_driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For vpif capture driver each IRQ resource contains a single IRQ
so drop the second loop.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ideally the freeing of irq's and the global variables needs to be
done in the remove() rather than module_exit(), this patch moves
the freeing up of irq's and freeing the memory allocated to channel
objects to remove() callback of struct platform_driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes unwanted header include of mach/hardware.h
and along side sorts the header inclusion alphabetically.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver did not yet support struct v4l2_device, so add it. This
make it possible to replace the deprecated parent field with the
v4l2_dev field, allowing the eventual removal of the parent field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The parent field will eventually disappear to be replaced by v4l2_dev.
soc_camera does provide a v4l2_device struct but did not point to it in
struct video_device. This is now fixed.
Now the video nodes can be found under the correct platform bus, and
the advanced debug ioctls work correctly as well (the core implementation
of those ioctls requires that v4l2_dev is set correctly).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The $obj-m/$obj-y vars should be adding new modules to build, not
overriding it. So, it should never use
$obj-y := foo.o
instead, it should use:
$obj-y += foo.o
Failing to do that is very bad, as it will suppress needed modules.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
