* pci/aer:
PCI/AER: Clear error status registers during enumeration and restore
* pci/hotplug:
PCI: pciehp: Queue power work requests in dedicated function
* pci/misc:
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
x86/PCI: Make pci_subsys_init() static
PCI: Add builtin_pci_driver() to avoid registration boilerplate
PCI: Remove unnecessary "if" statement
* pci/msi:
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
PCI/MSI: Export all remapped MSIs to sysfs attributes
PCI: Disable MSI on SiS 761
* pci/resource:
sparc/PCI: Add mem64 resource parsing for root bus
PCI: Expand Enhanced Allocation BAR output
PCI: Make Enhanced Allocation bitmasks more obvious
PCI: Handle Enhanced Allocation capability for SR-IOV devices
PCI: Add support for Enhanced Allocation devices
PCI: Add Enhanced Allocation register entries
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
* pci/virtualization:
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
PCI: Wait 1 second between disabling VFs and clearing NumVFs
PCI: Reorder pcibios_sriov_disable()
PCI: Remove VFs in reverse order if virtfn_add() fails
PCI: Remove redundant validation of SR-IOV offset/stride registers
PCI: Set SR-IOV NumVFs to zero after enumeration
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
PCI: Don't try to restore VF BARs
The Chelsio T5 has a PCIe compliance erratum that causes Malformed TLP or
Unexpected Completion errors in some systems, which may cause device access
timeouts.
Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same values
for the Attribute as were supplied in the header of the corresponding
Request, except as explicitly allowed when IDO is used."
Instead of copying the Attributes from the Request to the Completion, the
T5 always generates Completions with zero Attributes. The receiver of a
Completion whose Attributes don't match the Request may accept it (which
itself seems non-compliant based on sec 2.3.2), or it may handle it as a
Malformed TLP or an Unexpected Completion, which will probably lead to a
device access timeout.
Work around this by disabling "Relaxed Ordering" and "No Snoop" in the Root
Port so it always generate Requests with zero Attributes.
This does affect all other devices which are downstream of that Root Port,
but these are performance optimizations that should not make a functional
difference.
Note that Configuration Space accesses are never supposed to have TLP
Attributes, so we're safe waiting till after any Configuration Space
accesses to do the Root Port "fixup".
Based on original work by Casey Leedom <leedom@chelsio.com>
[bhelgaas: changelog, comments, rename to pci_find_pcie_root_port(), rework
to use pci_upstream_bridge() and check for Root Port device type, edit
diagnostics to clarify intent and devices affected]
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
MSI is broken on SiS 761 chipset at least on PC Chips A31G board. No
interrupts are delivered once MSI is enabled for a device. This causes
hang on X11 start with a nVidia card installed (with nouveau driver).
Disable MSI completely for this chipset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
The Intel 100-series chipset now includes the integrated Ethernet as part
of a multifunction package. The Ethernet function does not include native
ACS support, but Intel confirms that the device is not capable of peer-to-
peer within the package. We can therefore quirk it to expose the
isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <john.ronciak@gmail.com>
The PCI capabilities list for Intel DH895xCC VFs (device id 0x0443) with
QuickAssist Technology is prematurely terminated in hardware.
Workaround the issue by hard-coding the known expected next capability
pointer and saving the PCIE cap into internal buffer.
Patch generated against cryptodev-2.6
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Some quirks search for a HyperTransport capability and use a hard-coded TTL
value of 48 to avoid an infinite loop.
Move the definition of PCI_FIND_CAP_TTL to pci.h and use it instead of the
hard-coded TTL values.
[bhelgaas: changelog]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI class in dev->class is a three-byte value comprising a base class,
sub-class, and interface type. PCI_CLASS_NOT_DEFINED includes the base
class and sub-class, but not the interface type, so it should be shifted to
make space for the interface. It happens that PCI_CLASS_NOT_DEFINED is
zero, so it doesn't matter in the end, but we should still use it
consistently with other class definitions.
Treat PCI_CLASS_NOT_DEFINED as a base class/sub-class value that should
appear in bits 8-23 of dev->class.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Revert aeb30016fe ("PCI: add Intel USB specific reset method").
We checked for "dev->class == PCI_CLASS_SERIAL_USB", but dev->class
contains the entire three-byte base class/sub-class/interface, while
PCI_CLASS_SERIAL_USB is only the two-byte base class/sub-class.
This error meant that we used the Intel device-specific reset on devices
with class code 0x000c03 instead of those with class code 0x0c03xx.
0x000c03 is a reserved value in the 0x00 backwards compatibility base
class and shouldn't match any devices, so I think reset_intel_generic_dev()
always failed.
I considered adding a shift, but I can't test it, so it's as likely to
break something as to fix something.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Mathias Nyman <mathias.nyman@intel.com>
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074 ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Hemant Pedanekar <hemantp@ti.com>
In the generic quirk fixup_rev1_53c810(), added by a5312e28c1 ("[PATCH]
PCI: NCR 53c810 quirk"), we assigned "class = PCI_CLASS_STORAGE_SCSI". But
PCI_CLASS_STORAGE_SCSI is only the two-byte base class/sub-class and needs
to be shifted to make space for the low-order interface byte.
Furthermore, we had a similar quirk, pci_fixup_ncr53c810(), for arch/x86,
which assigned class correctly. The arch code is linked before the PCI
core, so arch quirks run before generic quirks. Therefore, on x86, the x86
arch quirk ran first, and the generic quirk did nothing because it saw that
dev->class was already set. But on other arches, the generic quirk set the
wrong class code.
Fix the generic quirk to set the correct class code and remove the
now-unnecessary x86-specific quirk.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <matthew@wil.cx>
be6646bfba ("PCI: Prevent xHCI driver from claiming AMD Nolan USB3 DRD
device") added a quirk to override the PCI class code of the AMD Nolan
device.
Use PCI_CLASS_SERIAL_USB instead of a bare number to improve greppability.
Also add a log message about what we're doing.
No functional change except the new message.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huang Rui <ray.huang@amd.com>
CC: Jason Chang <jason.chang@amd.com>
CC: Felipe Balbi <balbi@ti.com>
Intersil/Techwell TW686[4589]-based video capture cards have an empty
(zero) class code. Fix it.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just like Haswell, Intel Atom Cherrytrail does not need the default 10ms
d3_delay imposed by the PCI specification.
Expand quirk_remove_d3_delay() to apply to Cherrytrail devices, so we can
ignore the 10ms delay before entering or exiting D3 suspend.
[bhelgaas: changelog, comment]
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Marvell 9120 SATA controller has the same issue as a number of others, so
use the same quirk for this one. The other quirks were added by
cc346a4714 ("PCI: Add function 1 DMA alias quirk for Marvell devices").
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Intel confirms that 9-series chipset root ports provide ACS-equivalent
isolation when configured via the existing Intel PCH ACS quirk setup.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
The PCI core now disables MSI and MSI-X for all devices during enumeration
regardless of CONFIG_PCI_MSI. Remove device-specific code to disable
MSI/MSI-X.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The SiS apic bug workaround is now obsolete as we cache the register
values for performance reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1428978610-28986-22-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* pci/misc:
PCI: Read capability list as dwords, not bytes
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
Intel has verified that there is no peer-to-peer between functions for the
below selection of 82580, 82576, 82575, I350, and 82571 multi-port devices.
This adds the necessary quirks to consider the functions isolated from each
other. 82571 quad-port devices are omitted due to likely lack of
ACS/isolation in the onboard switch, rendering quirks for the downstream
endpoints useless.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
Some AMD CS553x devices have read-only BARs because of a firmware or
hardware defect. There's a workaround in quirk_cs5536_vsa(), but it no
longer works after 36e8164882 ("PCI: Restore detection of read-only
BARs"). Prior to 36e8164882, we filled in res->start; afterwards we
leave it zeroed out. The quirk only updated the size, so the driver tried
to use a region starting at zero, which didn't work.
Expand quirk_cs5536_vsa() to read the base addresses from the BARs and
hard-code the sizes.
On Nix's system BAR 2's read-only value is 0x6200. Prior to 36e8164882,
we interpret that as a 512-byte BAR based on the lowest-order bit set. Per
datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to
avoid clearing any address bits if a platform uses only 64-byte alignment.
[bhelgaas: changelog, reduce BAR 2 size to 64]
Fixes: 36e8164882 ("PCI: Restore detection of read-only BARs")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4
Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf
Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdf
Reported-and-tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v.2.6.27+
Intel has confirmed that the Wellsburg chipset, while not reporting ACS,
does provide the proper isolation through the RCBA/BSPR registers, so the
same quirk works for this set of device IDs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
The Adaptec 3405 is actually an Intel 80333 I/O processor where the exposed
device at 0e.0 is actually the address translation unit of the I/O
processor and a hidden, private device at 01.0 masters the DMA for the
device. Create a fixed alias between the exposed and hidden devfn so we
can enable the IOMMU.
Scenarios like this are potentially likely for any device incorporating
this I/O processor, so this little bit of abstraction with the fixed alias
table should make future additions trivial.
Without this fix, booting a system with the Intel IOMMU enabled and an
Adaptec 3405 at 02:0e.0 results in a flood of errors like this:
dmar: DRHD: handling fault status reg 3
dmar: DMAR:[DMA Write] Request device [02:01.0] fault addr ffbff000
DMAR:[fault reason 02] Present bit in context entry is clear
[bhelgaas: changelog, comment]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
As Skyhawk and BE3-R (both multi-function devices) don't advertise the
PCI-ACS capability, the vfio driver places all the functions of these
devices in a single IOMMU group. Attaching (via PCI-passthru) two
different Skyhawk/BE3-R partitions (nPAR, Flex, etc. PFs) using vfio, to
different guests doesn't work as vfio only allows functions in *different*
IOMMU groups to be assigned to different guests.
As peer-to-peer access between PFs in Skyhawk/BE3-R is not possible, we can
treat them as "fully isolated" even though the device doesn't advertise
ACS. Add a PCI quirk for Skyhawk and BE3-R chips to fix this problem.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Some AMD/ATI GPUs report NoSoftRst- to indicate that they perform a reset
when software transitions them from D3hot to D0, but there is no apparent
effect on the device: the monitor remains synced and the framebuffer
contents are retained.
Callers of pci_reset_function() don't necessarily have a way to validate
whether a reset was effective, so we don't want to rely on NoSoftRst if
it's known to be inaccurate. Returning an error in such cases appears to
be the better option. For users like vfio-pci, this allows the driver to
escalate to the bus reset interfaces.
If a device lives on the root bus, there's really no further
escalation path, so we exempt PM reset as potentially better than
nothing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reports against the TL-WDN4800 card indicate that PCI bus reset of this
Atheros device cause system lock-ups and resets. I've also been able to
confirm this behavior on multiple systems. The device never returns from
reset and attempts to access config space of the device after reset result
in hangs. Blacklist bus reset for the device to avoid this issue.
[bhelgaas: This regression appeared in v3.14. Andreas bisected it to
425c1b223d ("PCI: Add Virtual Channel to save/restore support"), but we
don't understand the mechanism by which that commit affects the reset
path.]
[bhelgaas: changelog, references]
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Reported-by: Andreas Hartmann <andihartmann@freenet.de>
Tested-by: Andreas Hartmann <andihartmann@freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
The AMD Nolan (NL) SoC contains a DesignWare USB3 Dual-Role Device that can
be operated either as a USB Host or a USB Device. In the AMD NL platform,
this device ([1022:7912]) has a class code of PCI_CLASS_SERIAL_USB_XHCI
(0x0c0330), which means the xhci driver will claim it.
But the dwc3 driver is a more specific driver for this device, and we'd
prefer to use it instead of xhci. To prevent xhci from claiming the
device, change the class code to 0x0c03fe, which the PCI r3.0 spec defines
as "USB device (not host controller)". The dwc3 driver can then claim it
based on its Vendor and Device ID.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AMD has confirmed that peer-to-peer between two southbridge functions does
not occur.
Add a quirk to indicate that these functions are isolated even though they
don't have an ACS capability.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81841
Signed-off-by: Marti Raudsepp <marti@juffo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joel Schopp <joel.schopp@amd.com>
Intel has verified there is no peer-to-peer between functions for the below
selection of 82598, 82599, and X520 10G NICs. These NICs lack an ACS
capability, so we're not able to determine this isolation without the help
of quirks.
Generalize the Solarflare quirk and add these Intel 10G NICs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <John.ronciak@intel.com>
Solarflare confirms that these devices do not allow peer-to-peer between
functions. Quirk them to allow IOMMU grouping to expose this isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Stonehouse <rstonehouse@solarflare.com>
pci_get_dma_source() is unused, so remove it. We now have
dma_alias_devfn() to describe this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/enumeration:
PCI: Enable CRS Software Visibility for root port if it is supported
PCI: Check only the Vendor ID to identify Configuration Request Retry
* pci/misc:
PCI: Parenthesize PCI_DEVID and PCI_VPD_LRDT_ID parameters
PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size
PCI/AER: Make <linux/aer.h> standalone includable
* pci/virtualization:
PCI: Use device flag helper functions
xen/pciback: Use PCI device flag helper functions
KVM: Use PCI device flag helper functions
PCI: Add device flag helper functions
PCI: Assume all Mellanox devices have broken INTx masking
The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to
an erratum, setting the SR-IOV page size causes the physical function BARs
to expand to the system page size. Since ppc64 uses 64k pages, when Linux
tries to assign the smaller resource sizes to the now 64k BARs the address
will be truncated and the BARs will overlap.
Force Linux to allocate the resource as a full page, which avoids the
overlap.
[bhelgaas: print expanded resource, too]
Signed-off-by: Douglas Lehr <dllehr@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Milton Miller <miltonm@us.ibm.com>
CC: stable@vger.kernel.org
The VFIO driver routes LSI interrupts by capturing, masking, and then
delivering. When passing though Mellanox adapters from host to guest,
interrupt storm are reported from host and guest. That's because the PCI
command register INTx Disable bit doesn't work on Mellanox devices.
# lspci | grep Mellanox
0001:05:00.0 Ethernet controller: Mellanox Technologies MT27500 Family [ConnectX-3]
0005:01:00.0 Ethernet controller: Mellanox Technologies MT26448 [ConnectX EN 10GigE, PCIe 2.0 5GT/s] (rev b0)
Amir Vadai confirmed that all Mellanox devices have same problem.
The patch marks broken INTx masking for all Mellanox adapters.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops, some
other new drivers, testing fixes, and other good things. All have been
in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1LcACgkQMUfUDdst+ymaVwCgqMrKFmpduBufOSFROhxlfB5Q
ajsAoNDmIn3pgla+kj23Y5ib20aMi++s
=IdIr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver patches from Greg KH:
"Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops,
some other new drivers, testing fixes, and other good things. All
have been in linux-next for a long time"
* tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits)
misc: bh1780: Introduce the use of devm_kzalloc
Lattice ECP3 FPGA: Correct endianness
drivers/misc/ti-st: Load firmware from ti-connectivity directory.
dt-bindings: extcon: Add support for SM5502 MUIC device
extcon: sm5502: Change internal hardware switch according to cable type
extcon: sm5502: Detect cable state after completing platform booting
extcon: sm5502: Add support new SM5502 extcon device driver
extcon: arizona: Get MICVDD against extcon device
extcon: Remove unnecessary OOM messages
misc: vexpress: Fix sparse non static symbol warnings
mei: drop unused hw dependent fw status functions
misc: bh1770glc: Use managed functions
pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage
misc: remove DEFINE_PCI_DEVICE_TABLE usage
ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use
drivers/char/dsp56k.c: drop check for negativity of unsigned parameter
mei: fix return value on disconnect timeout
mei: don't schedule suspend in pm idle
mei: start disconnect request timer consistently
mei: reset client connection state on timeout
...
This bridge sometimes shows up as a root complex device and sometimes as a
discrete PCIe-to-PCI bridge. Testing indicates that in the latter case, we
need to enable the PCIe bridge DMA alias quirk.
Reported-by: Milos Kaurin <milos.kaurin@gmail.com>
Tested-by: Milos Kaurin <milos.kaurin@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add two quirks to support thunderbolt suspend/resume on Apple systems.
We need to perform two different actions during suspend and resume:
The whole controller has to be powered down before suspend. If this is
not done then the native host interface device will be gone after resume
if a thunderbolt device was plugged in before suspending. The controller
represents itself as multiple PCI devices/bridges. To power it down we
hook into the upstream bridge of the controller and call the magic ACPI
methods. Power will be restored automatically during resume (by the
firmware presumably).
During resume we have to wait for the native host interface to
reestablish all pci tunnels. Since there is no parent-child relationship
between the NHI and the bridges we have to explicitly wait for them
using device_pm_wait_for_dev. We do this in the resume_noirq phase of
the downstream bridges of the controller (which lead into the
thunderbolt tunnels).
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pci_fixup_suspend_late as a new pci_fixup_pass. The pass is called
from suspend_noirq and poweroff_noirq. Using the same pass for suspend
and hibernate is consistent with resume_early which is called by
resume_noirq and restore_noirq.
The new quirk pass is required for Thunderbolt support on Apple
hardware.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device uses function 1 as the PCIe requester ID.
This vendor has similar boards based on the same Marvell 88SE9235 chipset,
but this patch was only tested with the 642L.
Tested on ASUS Sabertooth 990FX (AMD).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Signed-off-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.
No functional change.
[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix various whitespace errors.
No functional change.
[bhelgaas: fix other similar problems]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ITE 8892 is a PCIe-to-PCI bridge but doesn't have a PCIe capability.
Quirk it so we can figure out the DMA alias for devices below the bridge,
so they work correctly with an IOMMU.
[bhelgaas: add changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=73551
Reported-by: Ronald <rwarsow@gmx.de>
Tested-by: Ronald <rwarsow@gmx.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/iommu:
PCI: Add bridge DMA alias quirk for ASMedia and Tundra bridges
PCI: Add support for PCIe-to-PCI bridge DMA alias quirks
PCI: Add function 1 DMA alias quirk for Marvell devices
PCI: Add function 0 DMA alias quirk for Ricoh devices
PCI: Add support for DMA alias quirks
PCI: Convert pci_dev_flags definitions to bit shifts
PCI: Add DMA alias iterator
The quirk is intended to be extremely generic, but we only apply it to
known offending devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44881
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several Marvell devices and a JMicron device have a similar DMA requester
ID problem to Ricoh, except they use function 1 as the PCIe requester ID.
Add a quirk for these to populate the DMA alias with the correct devfn.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Tested-by: George Spelvin <linux@horizon.com>
Tested-by: Andreas Schrägle <ajs124.ajs124@gmail.com>
Tested-by: Tobias N <qemu@suppser.de>
Tested-by: <daxcore@online.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The existing quirk for these devices (pci_get_dma_source()) doesn't really
solve the problem; re-implement it using the DMA alias iterator. We'll
come back later and remove the existing quirk and dma_source interface.
Note that device ID 0xe822 is typically function 0 and 0xe230 has been
tested to not need the quirk and are therefore removed versus the
equivalent dma_source quirk. If there exist in other configurations we can
re-add them.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=605888
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* dma-api:
iommu/exynos: Remove unnecessary "&" from function pointers
DMA-API: Update dma_pool_create ()and dma_pool_alloc() descriptions
DMA-API: Fix duplicated word in DMA-API-HOWTO.txt
DMA-API: Capitalize "CPU" consistently
sh/PCI: Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
DMA-API: Change dma_declare_coherent_memory() CPU address to phys_addr_t
DMA-API: Clarify physical/bus address distinction
* pci/virtualization:
PCI: Mark RTL8110SC INTx masking as broken
* pci/msi:
PCI/MSI: Remove pci_enable_msi_block()
* pci/misc:
PCI: Remove pcibios_add_platform_entries()
s390/pci: use pdev->dev.groups for attribute creation
PCI: Move Open Firmware devspec attribute to PCI common code
* pci/resource:
PCI: Add resource allocation comments
PCI: Simplify __pci_assign_resource() coding style
PCI: Change pbus_size_mem() return values to be more conventional
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources
PCI: Support BAR sizes up to 8GB
resources: Clarify sanity check message
PCI: Don't add disabled subtractive decode bus resources
PCI: Don't print anything while decoding is disabled
PCI: Don't set BAR to zero if dma_addr_t is too small
PCI: Don't convert BAR address to resource if dma_addr_t is too small
PCI: Reject BAR above 4GB if dma_addr_t is too small
PCI: Fail safely if we can't handle BARs larger than 4GB
x86/gart: Tidy messages and add bridge device info
x86/gart: Replace printk() with pr_info()
x86/PCI: Move pcibios_assign_resources() annotation to definition
x86/PCI: Mark ATI SBx00 HPET BAR as IORESOURCE_PCI_FIXED
x86/PCI: Don't try to move IORESOURCE_PCI_FIXED resources
x86/PCI: Fix Broadcom CNB20LE unintended sign extension
INTx masking does not work on this device. To see this, configure the
network device UP on an active network, note that the interrupt count
continues to increment for the device in /proc/interrupts. Use setpci to
set the PCI_COMMAND_INTX_DISABLE bit in the PCI_COMMAND register. As
expected, the interrupt count ceases to increment. However, reading the
PCI_STATUS_INTERRUPT bit of the PCI_STATUS register does not indicate that
interrupts are pending and clearing PCI_COMMAND_INTX_DISABLE in the
PCI_COMMAND register does not allow the device to continue operation.
This does not affect operation of the host r8169 driver, but it does
prevent the device from being functional when assigned to a VM, such as
with QEMU and VFIO. The guest driver successfully probes the device, but
there is no traffic. Mark INTx masking as broken, allowing the more
restrictive APIC masking to be used instead.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
PCI: rphahp: Fix endianess issues
PCI: Allow hotplug service drivers to operate in polling mode
PCI: pciehp: Acknowledge spurious "cmd completed" event
PCI: pciehp: Use PCI_EXP_SLTCAP_PSN define
PCI: hotplug: Remove unnecessary "dev->bus" test
* pci/msi:
GenWQE: Use pci_enable_msi_exact() instead of pci_enable_msi_block()
PCI/MSI: Simplify populate_msi_sysfs()
PCI/portdrv: Use pci_enable_msix_exact() instead of pci_enable_msix()
* pci/virtualization:
PCI: Add Patsburg (X79) to Intel PCH root port ACS quirk
* pci/misc:
PCI: Fix use of uninitialized MPS value
PCI: Remove dead code
MAINTAINERS: Add arch/x86/kernel/quirks.c to PCI file patterns
PCI: Remove unnecessary __ref annotations
PCI: Fail new_id for vendor/device values already built into driver
PCI: Add new ID for Intel GPU "spurious interrupt" quirk
PCI: Update my email address
PCI: Fix incorrect vgaarb conditional in WARN_ON()
PCI: Use designated initialization in PCI_VDEVICE
PCI: Remove old serial device IDs
PCI: Remove unnecessary includes of <linux/init.h>
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.
It turned out that the new CPU also featured a new GPU with a different PCI
ID.
Add this PCI ID to the quirk table. Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.
[bhelgaas: add f67fd55fa9 reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.4+
Intel has updated Red Hat bz1037684 to note that X79 PCH root ports also
provide isolation and the same ACS quirks apply. Some sources indicate
additional device IDs for X79, but this patch includes only the ones
specifically identified by Intel:
https://bugzilla.redhat.com/show_bug.cgi?id=1037684#c11
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
* pci/resource: (26 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
PCI: Remove pci_find_parent_resource() use for allocation
...
When assigning addresses to resources, mark them with IORESOURCE_UNSET
before we start and clear IORESOURCE_UNSET if assignment is successful.
That means that if we print the resource during assignment, we will show
the size, not a meaningless address.
Also, clear IORESOURCE_UNSET if we do assign an address, so we print the
address when it is valid.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many of the currently available Intel PCH-based root ports do not provide
PCIe ACS capabilities. Without this, we must assume that peer-to-peer
traffic between multifunction root ports and between devices behind root
ports is possible. This lack of isolation is exposed by grouping the
devices together in the same IOMMU group. If we want to expose these
devices to userspace, vfio uses IOMMU groups as the unit of ownership, thus
making it very difficult to assign individual devices to separate users.
The good news is that the chipset does provide ACS-like isolation
capabilities, but we do need to verify and enable those capabilities if the
BIOS has not done so. This patch implements the device specific enabling
and testing of equivalent ACS function for these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
Some devices support PCI ACS-like features, but don't report it using the
standard PCIe capabilities. We already provide hooks for device-specific
testing of ACS, but not for device-specific enabling of ACS. This provides
that setup hook.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This tool hasn't been maintained in over a decade, and is pretty much
useless these days. Let's pretend it never happened.
Also remove a long-dead email address.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The latest Intel Haswell chipsets have a hardware optimization which
allows on-chip PCI devices to ignore the 10ms delay before entering
or exiting D3 suspend.
This patch implements the optimization as a PCI quirk, since we want
tight control over which devices use it. This way we can test each device
individually to be sure there are no issues before we enable the quirk.
The first set of devices are from the Haswell platform, which includes
every PCI device that is on the northbridge and southbridge.
This patch reduces the Haswell suspend time from 93 ms to 47 ms and resume
time from 160 ms to 64 ms.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/vipul-chelsio-reset-v2:
PCI: Use pci_wait_for_pending_transaction() instead of for loop
bnx2x: Use pci_wait_for_pending_transaction() instead of for loop
PCI: Chelsio quirk: Enable Bus Master during Function-Level Reset
PCI: Add pci_wait_for_pending_transaction()
New routine has been added to avoid duplication of code to wait for
pending PCI transactions to complete. This makes use of that function.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
T4 can wedge if there are DMAs in flight within the chip and Bus
Master has been disabled. We need to have it on till the Function
Level Reset completes. T4 can also suffer a Head Of Line blocking
problem if MSI-X interrupts are disabled before the FLR has completed.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AMD confirmed that peer-to-peer between these devices is
not possible. We can therefore claim that they support a
subset of ACS.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Donald Dutile <ddutile@redhat.com>
* pci/misc:
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI PM cap register offset has been saved in pci_pm_init(),
so we can use pdev->pm_cap instead of using pci_find_capability(..)
here.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To add AMD CZ SATA controller device ID of IDE mode.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Certain NTB devices have a hardware erratum where, regardless of
pre-configured value, reading the BAR size returns 4096. To work around
this issue, add a PCI quirk to read the appropriate values from an
alternative register in PCI config space and move the resource endpoints
to the appropriate location.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Before every call of quirk_io_region(), pci_read_config_word() is called.
We can fold that call into quirk_io_region() to make code more readable.
[bhelgaas: changelog, fill bus_region directly rather than copying from res]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following PCIe devices with revision lower than 0x18 have this bug:
AR8161(1091)/AR8162(1090)/AR8171(10A1)/AR8172(10A0)/E210X(E091).
Signed-off-by: Huang,Xiong <xiong@qca.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Otherwise it fails like this on cards like the Transcend 16GB SDHC card:
mmc0: new SDHC card at address b368
mmcblk0: mmc0:b368 SDC 15.0 GiB
mmcblk0: error -110 sending status command, retrying
mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb0
Tested on my Lenovo x200 laptop.
[bhelgaas: changelog]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Chris Ball <cjb@laptop.org>
CC: Manoj Iyer <manoj.iyer@canonical.com>
CC: stable@vger.kernel.org
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQyKwSAAoJEPGMOI97Hn6zScgQAJZK2VDfCv74mKrgSDNokIzH
5nVDrc9AHKJm7CUODs6keJK5d4TD/za3Zao68zrYHsJJKes2ni2Z3W34HP2RXKK2
eOmePXOHYPPZMlimP9r9cVxNu1ZJCyp/yWSBcsPF4zUgWhBWLRaSj85I049gQ0sz
+05nZYfLjVd3HNiaXsG4CQyMrNF46XEsLhF9vs+Nr2GHPwrpzhfScgYv63oDS86C
3ICKsjmiRUZcNelxIFYmyxa5u89QdW5XHjzc9eHGQuus24Vxw+TZzsdfc17sUJEE
HTyXY+RjDpOVhdtwwUjrCEOiyZYvy3g9+3sKxoxgt/76ghdUaR7fxITwB97qVMFD
T0ESlKjSV/Qv5QYdyy5uP4zwNs/PXCWXkTg/L1m71F30BxKWDa7tgiA6uK7Z7fl5
1aokKBdk3mtJJJIDJG1YkxPXx/JItTGCNYrx7CcFj49rSjrUWLQdmrYahersRIsB
3wiD2xTi9e4dXeP/+VGzGOWB/sHk+73jvrvZe/REa1FCnMINDz4+9V9WaGROMqyq
MQ8kX0KfYcNVNxy1GOXjU5wLpMN/t/QbvI7gwzRP1DAUCJPoOgFy7AjvSTVG3zuy
8CtdOFttVkUn5dqsbQR0gVbyQVTS3PGSKz5XC/s8kVDWhja0xZTBYwrskM/4zdSD
Xf48OyYV5EjpC3FYUSiU
=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
CONFIG_HOTPLUG is going away as an option so __devexit_p, __devint,
__devinitdata, __devinitconst, and _devexit are no longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Meilhaus ME-2000i and ME-2600i data acquisition cards supported by
the Comedi "me_daq" driver use the PLX PCI 9050 PCI Target bridge chip
affected by the bug that prevents the chip's local configuration
registers being read from BAR0 or BAR1 base addresses that are an odd
multiple of 128 bytes. Use the PLX PCI 9050 quirk handler for these
devices to re-allocate affected regions to a 256-byte boundary.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PLX PCI 9050 PCI Target bridge controller has a bug that prevents
its local configuration registers being read through BAR0 (memory) or
BAR1 (i/o) if the base address lies on an odd 128-byte boundary, i.e. if
bit 7 of the base address is non-zero. This bug is described in the PCI
9050 errata list, version 1.4, May 2005. It was fixed in the
pin-compatible PCI 9052, which can be distinguished from the PCI 9050 by
checking the revision in the PCI header, which is hard-coded for these
chips.
Workaround the problem by re-allocating the affected regions to a
256-byte boundary. Note that BAR0 and/or BAR1 may have been disabled
(size 0) during initialization of the PCI chip when its configuration is
read from a serial EEPROM.
Currently, the fix-up has only been used for devices with the default
vendor and device ID of the PLX PCI 9050. The PCI 9052 shares the same
default device ID as the PCI 9050 but they have different PCI revision
codes.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Before initiating an FLR, we should wait for completion of any outstanding
non-posted requests. See PCIe spec r3.0, sec 6.6.2.
This makes reset_intel_82599_sfp_virtfn() very similar to the generic
pcie_flr(). The only difference is that the 82599 doesn't report FLR
support in the VF Device Capability register.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
Pull arch/tile updates from Chris Metcalf:
"These changes provide support for PCIe root complex and USB host mode
for tilegx's on-chip I/Os.
In addition, this pull provides the required underpinning for the
on-chip networking support that was pulled into 3.5. The changes have
all been through LKML (with several rounds for PCIe RC) and on
linux-next."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: updates to pci root complex from community feedback
bounce: allow use of bounce pool via config option
usb: add host support for the tilegx architecture
arch/tile: provide kernel support for the tilegx USB shim
tile pci: enable IOMMU to support DMA for legacy devices
arch/tile: enable ZONE_DMA for tilegx
tilegx pci: support I/O to arbitrarily-cached pages
tile: remove unused header
arch/tile: tilegx PCI root complex support
arch/tile: provide kernel support for the tilegx TRIO shim
arch/tile: break out the "csum a long" function to <asm/checksum.h>
arch/tile: provide kernel support for the tilegx mPIPE shim
arch/tile: common DMA code for the GXIO IORPC subsystem
arch/tile: support MMIO-based readb/writeb etc.
arch/tile: introduce GXIO IORPC framework for tilegx
This change implements PCIe root complex support for tilegx using
the kernel support layer for accessing the TRIO hardware shim.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> [changes in 07487f3]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
My "PCI: Integrate 'pci_fixup_final' quirks into hot-plug paths" patch
introduced an undefined reference to 'pci_fixup_final_inited' when
CONFIG_PCI_QUIRKS is not enabled (on x86_64):
drivers/built-in.o: In function `pci_bus_add_device':
(.text+0x4f62): undefined reference to `pci_fixup_final_inited'
This patch removes the external reference ending up with a result closer
to what we ultimately want when the boot path issues described in the
original patch are resolved.
References:
https://lkml.org/lkml/2012/7/9/542 Original, offending, patch
https://lkml.org/lkml/2012/7/12/338 Randy's catch
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend. It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.
It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working. Consequently
commit c2fb8a3fa2 (USB: add
NO_D3_DURING_SLEEP flag and revert 151b612847) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.
Now we know the actual cause of the problem. Thanks to AceLan Kao for
tracking it down.
According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows. When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS. Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state. If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so. This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3. The end result is
a system hang or memory corruption.
Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend. This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.
In theory we could do this for every PCI device. However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.
Finally the affected systems can suspend with USB wakeup working
properly.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728
Based-on-patch-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Javier Marcet <jmarcet@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pci/bjorn-p2p-bridge-windows:
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: allow P2P bridge windows starting at PCI bus address zero
Conflicts:
drivers/pci/probe.c
include/linux/pci.h
* pci/myron-final-fixups-v2:
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
Final fixups are currently applied only at boot-time by
pci_apply_final_quirks(), which is an fs_initcall(). Hot-added devices
don't get these fixups, so they may not be completely initialized.
This patch makes us run final fixups for hot-added devices in
pci_bus_add_device() just before the new device becomes eligible for driver
binding.
This patch keeps the fs_initcall() for devices present at boot because we
do resource assignment between pci_bus_add_device and the fs_initcall(),
and we don't want to break any fixups that depend on that assignment. This
is a design issue that may be addressed in the future -- any resource
assignment should be done *before* device_add().
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Final fixups are executed during device enumeration. If we support
hotplug, this may be after boot, so final fixups cannot be __init.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
9d265124d0 and 15a260d53f added quirks for P2P bridges that support
I/O windows that start/end at 1K boundaries, not just the 4K boundaries
defined by the PCI spec. For details, see the IOBL_ADR register and the
EN1K bit in the CNF register in the Intel 82870P2 (P64H2).
These quirks complicate the code that reads P2P bridge windows
(pci_read_bridge_io() and pci_cfg_fake_ranges()) because the bridge
I/O resource is updated in the HEADER quirk, in pci_read_bridge_io(),
in pci_setup_bridge(), and again in the FINAL quirk. This is confusing
and makes it impossible to reassign the bridge windows after FINAL
quirks are run.
This patch adds support for 1K windows in the generic paths, so the
HEADER quirk only has to enable this support. The FINAL quirk, which
used to undo damage done by pci_setup_bridge(), is no longer needed.
This removes "if (!res->start) res->start = ..." from pci_read_bridge_io();
that was part of 9d265124d0 to avoid overwriting the resource filled in
by the quirk. Since pci_read_bridge_io() itself now knows about
granularity, the quirk no longer updates the resource and this test is no
longer needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The enable/suspend/resume_early/resume fixups can be called at any time, so
they can't be __init or __devinit.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
__nv_msi_ht_cap_quirk() acquires a temporary reference via
'pci_get_bus_and_slot()' that is never released.
This patch releases the temporary reference.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch restructures pci_do_fixups()'s quirk invocations in the style
of initcall_debug_start() and initcall_debug_report(), so we have only
one call site for the quirk.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* topic/sebastian-devinit-fixups:
scripts/modpost: check for bad references in .pci.fixups area
sh/PCI: move fixup hooks from __init to __devinit
powerpc/PCI: move fixup hooks from __init to __devinit
frv/PCI: move fixup hooks from __init to __devinit
arm/PCI: move fixup hooks from __init to __devinit
alpha/PCI: move fixup hooks from __init to __devinit
PCI: move fixup hooks from __init to __devinit
x86/PCI: move fixup hooks from __init to __devinit
Passes pci_intx_mask_supported test but continues to send interrupts
as discovered through VFIO-based device assignment.
http://www.spinics.net/lists/kvm/msg73738.html
[bhelgaas: use HEADER, not FINAL, which is currently broken for hotplug]
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
According to
http://thread.gmane.org/gmane.comp.emulators.kvm.devel/91388
the T310 does not properly support INTx masking as it fails to keep the
PCI_STATUS_INTERRUPT bit updated once the interrupt is masked. Mark this
adapter as broken so that pci_intx_mask_supported won't report it as
compatible.
[bhelgaas: use HEADER, not FINAL, which is currently broken for hotplug]
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_intx_mask_supported() assumes INTx masking is supported if the
PCI_COMMAND_INTX_DISABLE bit is writable. But when that bit is set,
some devices don't actually mask INTx or update PCI_STATUS_INTERRUPT
as we expect.
This patch adds a way for quirks to identify these broken devices.
[bhelgaas: split out from Chelsio quirk addition]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a PCI environment, transactions aren't always required to reach
the root bus before being re-routed. Intermediate switches between
an endpoint and the root bus can redirect DMA back downstream before
things like IOMMUs have a chance to intervene. Legacy PCI is always
susceptible to this as it operates on a shared bus. PCIe added a
new capability to describe and control this behavior, Access Control
Services, or ACS.
The utility function pci_acs_enabled() allows us to test the ACS
capabilities of an individual devices against a set of flags while
pci_acs_path_enabled() tests a complete path from a given downstream
device up to the specified upstream device. We also include the
ability to add device specific tests as it's likely we'll see
devices that do not implement ACS, but want to indicate support
for various capabilities in this space.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DMA transactions are tagged with the source ID of the device making
the request. Occasionally hardware screws this up and uses the
source ID of a different device (often the wrong function number of
a multifunction device). A specific Ricoh multifunction device is
a prime example of this problem and included in this patch.
Given a pci_dev, this function returns the pci_dev to use as the
source ID for DMA. When hardware works correctly, this returns
the input device. For the components of the Ricoh multifunction
device, it returns the pci_dev for function 0.
This will be used by IOMMU drivers for determining the boundaries
of IOMMU groups as multiple devices using the same source ID must
be contained within the same group. This can also be used by
existing streaming DMA paths for the same purpose.
[bhelgaas: fold in pci_dev_get() for !CONFIG_PCI]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For IvyBridge Mobile platform, a system hang may occur if a FLR (Function
Level Reset) is asserted to internal graphics.
This quirk is a workaround for the IVB FLR errata issue. We are
disabling the FLR reset handshake between the PCH and CPU display, then
manually powering down the panel power sequencing and resetting the PCH
display.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Kay, Allen M <allen.m.kay@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All supported devices have one issue that msi interrupt doesn't assert
if pci command register bit (PCI_COMMAND_INTX_DISABLE) is set.
Add workaround in drivers/pci/quirks.c
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes it a little easier to figure out which device may have caused a
slow quirk.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This isn't really a quirk; calling it directly from pci_add_device makes
more sense.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Recently added support to allow quirks to report duration also make the
boot log very crowded when initcall_debug is specified.
One thing we can to do mitigate this is to not call quirks unnecessarily
by adding a new quirk declaration macro that takes a class argument.
The new macro takes a class value and a class shift value (since it can
vary) so that quirks will be limited to certain device classes, greatly
reducing the number we call on every PCI device addition.
-v2: fix v1 that left over of sparated patch.
-v3: according to Jesse, change cls to class, cls_shift, to class_shift.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.
These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.
Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.
Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
Probably the IRQ ends up somewhere unnoticed.
According to reports on the net, the Intel DH61WW board is also affected.
Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: Charlie Suffin <charlie.suffin@stratus.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While diagnosing some boot time issues on a platform, all that I
could see in the bootgraph/dmesg was that the system was spending
a lot of time in applying one or more PCI quirks... which
was virtually undebuggable.
This patch adds printk's in "initcall_debug" style to the dmesg,
which are added when the user asks for the initcall_debug
(the nr one tool to use when debugging boot hangs or boot time issues)
kernel command line option.
v2: add #includes so quirks can build on non-x86
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
They were implicitly getting it from device.h --> module.h but
we want to clean that up. So add the minimal header for these
macros.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Using legacy interrupts and TLPs > 256 bytes on the SFC4000 (all
revisions) may cause interrupt messages to be replayed. In some
systems this results in a non-recoverable MCE. Early boards using the
SFC4000 set the maximum payload size supported (MPSS) to 1024 bytes
and we should override that.
There are probably other devices with similar issues, so give this
quirk a generic name.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ricoh 1180:e823 does not recognize certain types of SD/MMC cards,
as reported at http://launchpad.net/bugs/773524. Lowering the SD
base clock frequency from 200Mhz to 50Mhz fixes this issue. This
solution was suggest by Koji Matsumuro, Ricoh Company, Ltd.
This change has no negative performance effect on standard SD
cards, though it's quite possible that there will be one on
UHS-1 cards.
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: Koji Matsumuro <matsumur@nts.ricoh.co.jp>
Cc: <stable@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Don't use the costly dmi_name_in_vendors() when we know the string we
are looking for can only be in the DMI board name field. This is more
robust and, more importantly, much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We were just lucky that ICH4_GPIO_EN and ICH6_GPIO_EN happen to have
the same value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:
"Device 0000:01:00.0 not available because of resource collisions"
The device cannot be operated because of the above issue.
This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some broken BIOSes on ICH4 chipset report an ACPI region which is in
conflict with legacy IDE ports when ACPI is disabled. Even though the
regions overlap, IDE ports are working correctly (we cannot find out
the decoding rules on chipsets).
So the only problem is the reported region itself, if we don't reserve
the region in the quirk everything works as expected.
This patch avoids reserving any quirk regions below PCIBIOS_MIN_IO
which is 0x1000. Some regions might be (and are by a fast google
query) below this border, but the only difference is that they won't
be reserved anymore. They should still work though the same as before.
The conflicts look like (1f.0 is bridge, 1f.1 is IDE ctrl):
pci 0000:00:1f.1: address space collision: [io 0x0170-0x0177] conflicts with 0000:00:1f.0 [io 0x0100-0x017f]
At 0x0100 a 128 bytes long ACPI region is reported in the quirk for
ICH4. ata_piix then fails to find disks because the IDE legacy ports
are zeroed:
ata_piix 0000:00:1f.1: device not available (can't reserve [io 0x0000-0x0007])
References: https://bugzilla.novell.com/show_bug.cgi?id=558740
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Per ICH4 and ICH6 specs, ACPI and GPIO regions are valid iff ACPI_EN
and GPIO_EN bits are set to 1. Add checks for these bits into the
quirks prior to the region creation.
While at it, name the constants by macros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Revert commit 7eb93b175d
Author: Yu Zhao <yu.zhao@intel.com>
Date: Fri Apr 3 15:18:11 2009 +0800
PCI: SR-IOV quirk for Intel 82576 NIC
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk was added before SR-IOV was in production and now all machines that
originally had this issue alreayd have bios updates to correct the issue. The
quirk itself is no longer needed and in fact causes bugs if run. Remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it. Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment. This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.
Resolves https://bugzilla.kernel.org/show_bug.cgi?id=23952
Tested successfully by the reporter and myself.
Cc: stable@kernel.org
Reported-by: Mathieu Bérard <mathieu@mberard.eu>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: stable@kernel.org [v2.6.32+]
Reported-by: Max Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This change enables PCI root complex support for TILEPro. Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc. However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).
The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space. The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified. Both of the latter two headers were
preliminary versions not meant for release before now - oh well.
There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A long time ago I worked on a RHEL5 bug in which kdump hung during boot
on a set of systems. The systems hung because they never received timer
interrupts during calibrate_delay. These systems also all had Opteron
processors on a hypertransport bus, bridged to a pci bus via an Nvidia
MCP55 northbridge chip. After much wrangling I managed to learn from
Nvidia that they have an undocumented register in some versions of that
chip which control how legacy interrupts are send to the cpu complex
when the ioapic isn't active. Nvidia defaults this register to only
send legacy interrupts to the BSP, so if kdump happens to boot on an AP,
we never get timer interrupts and boom. I had initially used this quirk
as a workaround, with my intent being to move apic initalization to an
earlier point in the boot process, so the setting of the register would
be irrelevant. Given the work involved in doing that however, the
fragile nature of the apic initalization code, and the fact that, over
the 2 years since we found this bug, the MCP55 is the only chip which
seems to have this issue, I've figure at this point its likely safer to
just carry the quirk around. By setting the referenced bits in this
hidden register, interrupts will be broadcast to all cpus when the
ioapic isn't active on the above described systems.
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When the Lenovo Ideapad S10-3 is booted with HT enabled,
it hits a boot hang in the intel_idle driver.
This occurs when entering ATM-C4 for the first time,
unless BM_STS is first cleared.
acpi_idle doesn't see this because it first checks
and clears BM_STS, but it would hit the same hang
if that check were disabled.
http://bugs.meego.com/show_bug.cgi?id=7093https://bugs.launchpad.net/ubuntu/+source/linux/+bug/634702
Signed-off-by: Len Brown <len.brown@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
Add support for JMB364 and 369.
Patch-originally-from: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is no reason to run NVidia-specific quirks related to HT MSI
mappings with MSI disabled via pci=nomsi, so make
__nv_msi_ht_cap_quirk() return immediately in that case.
This allows at least one machine to boot 100% of the time with
pci=nomsi (it still doesn't boot reliably without that).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16443 .
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.
A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.
Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
MSI delivery from on-board ahci controller doesn't work on K8M800. At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge. Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rainer Hurtado Navarro <publio.escipion.el.africano@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In all AMD 780 family northbridges, the vendor ID of the internal
graphics PCI/PCI bridge reads not as AMD but as that of the mainboard
vendor, because the hardware actually returns the value of the subsystem
vendor ID (erratum 18).
We currently have additional quirk entries for Asus and Acer, but it is
likely that we will encounter more systems with other vendor IDs.
Since we do not know in advance all possible vendor IDs, a better way to
find the device is to declare the quirk on the host bridge, whose ID is
always correct, and use that device as a stepping stone to find the PCI/
PCI bridge, if present.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Aries Lee <arieslee@jmicron.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
At the moment only PCI-E briges can be flagged as hotplug, thus
allowing manual resource preallocation via pci=hpmemsize=nnM and
pci=hpiosize=nnM kernel parameters. Some PCI hotplug bridges, e.g.
PLX 6254 can also benefit from this functionalily, as kernel fails
to properly allocate their resources when hotplug device is added
and PCI bus is rescanned.
This patch adds header quirk for PLX 6254 that marks this bridge
as hotplug. Other PCI bridges with similar problems can use it
as well.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As reported in <http://bugs.debian.org/552299>, MSI appears to be
broken for this on-board device. We already have a quirk for the
P5N32-SLI Premium; extend it to cover both variants of the board.
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The missing initialization of the nb_cntl.strap_msi_enable does not
seem to be the only problem that prevents MSI, so that quirk is not
sufficient to enable MSI on all machines. To be safe, disable MSI
unconditionally for the internal graphics and HDMI audio on these
chipsets.
[rjw: Added the PCI_VENDOR_ID_AI quirk.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pci_claim_resource() can fail, so pay attention and only claim success
when it actually succeeded. If pci_claim_resource() fails, it prints a
useful diagnostic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla 15287 indicates that there's a problem with Message Signalled
Interrupts on VIA K8T890 systems. Add a quirk to disable MSI on these
systems.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Tested-by: lh <jarryson@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
AMD says in section 2.5.4 (GFX MSI Enable) of #43291 (AMD 780G Family
Register Programming Requirements):
The SBIOS must enable internal graphics MSI capability in GCCFG by
setting the following: NBCFG.NB_CNTL.STRAP_MSI_ENABLE='1'
Quite a few BIOS writers misinterpret this sentence and think that
enabling MSI is an optional feature. However, clearing that bit just
prevents delivery of MSI messages but does not remove the MSI PCI
capabilities registers, and so leaves these devices unusable for any
driver that attempts to use MSI.
Setting that bit is not possible after the BIOS has locked down the
configuration registers, so we have to manually disable MSI for the
affected devices.
This fixes the codec communication errors in the HDA driver when
accessing the HDMI audio device, and allows us to get rid of the
overcautious quirk in radeon_irq_kms.c.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Alex Deucher <alexdeucher@gamil.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apply the CX700 quirk only when an external VT6212L is present (which
is the case for the errant hardware the quirk was written for), don't
touch the settings otherwise -- Hauppage PVR-500 tuners need PCI Bus
Parking in order to work and when that's turned on everything seems
to behave fine.
I guess the underlying problem is a combination of an external VT6212L
and the CX700 rather than the CX700's PCI being broken completely for
all cases...
Reported-by: Jeroen Roos <jeroen@roosnl.com>
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file). This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.
To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by commit 5b889bf23 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.
Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit b9c3b26641 ("PCI: support
device-specific reset methods") the kernel build is broken if
CONFIG_PCI_QUIRKS is unset.
Fix this by moving pci_dev_specific_reset() to drivers/pci/quirks.c and
providing an empty replacement for !CONFIG_PCI_QUIRKS builds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle device specific timeout and use FLR.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a new type of quirk for resetting devices at pci_dev_reset time.
This is necessary to handle device with nonstandard reset procedures,
especially useful for guest drivers.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to this patch, if pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, ...)
returns 0 for all dev, pci_cache_line_size ends up set to zero
(instead of pci_dfl_cache_line_size).
This patch ensures the pci_cache_line_size = pci_dfl_cache_line_size
setting in the above scenario.
This happens in case of a kvm-88 guest (where, consequently, the rtl8139
NIC failed to initialize).
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Csaba Henk <csaba@gluster.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2]. This
is the diff between v1 and v2.
The changes in this patch are:
- tidied vsprintf stack buffer to shrink and compute size more
accurately
- use %pR for decoding and %pr for "raw" (with type and flags) instead
of adding %pRt and %pRf
[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
AMD 813x rev. B1 (like rev. B2) devices generate no interrupts if
quirk_disable_amd_813x_boot_interrupt is executed, add an exception.
http://bugzilla.kernel.org/show_bug.cgi?id=14159
Patch also adds missing cases for DECLARE_PCI_FIXUP_RESUME and
DECLARE_PCI_FIXUP_FINAL calls to quirk_disable_amd_813x_boot_interrupt.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Tested-by: Gabriele Giorgetti <g.giorgetti@teamsystem.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
Having this as a device_initcall() means that some real device drivers
can actually initialise _before_ the quirks are run, which is wrong.
We want it to run _before_ device_initcall(), but _after_ fs_initcall(),
since some arch-specific PCI initialisation like pcibios_assign_resources()
is done at fs_initcall().
We could use rootfs_initcall() but I actually want to use that for the
IOMMU initialisation, which has to come after the quirks, but still
before the real devices. So use fs_initcall_sync() instead -- since this
is entirely synchronous, it doesn't hurt that it'll escape the
synchronisation.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function may have done more in the past, but all it does now is
apply the PCI_FIXUP_FINAL quirks. So name it sensibly and put it where
it belongs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the most recent additions to the list of 82576 device IDs
to the list of devices needing the SR-IOV quirk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
http://bugzilla.kernel.org/show_bug.cgi?id=12542 reports that with the
quirk not applied on resume, msi stops working after resuming and mcp78s
ahci fails due to IRQ mis-delivery. Apply it on resume too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Tj <linux@tjworld.net>
Reported-by: Nicolas Derive <kalon33@ubuntu.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
