During init queue a regulatory update to retrieve the default
regulatory settings from FW. If we're during recovery, only replay the
current country code to FW, if it exists.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The new API sets an MCC (mobile country code) to FW and receives a
channel structure to be used as a basis for an updated regulatory domain.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.
CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf318 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: Valentin Manea <linux-wireless@mrs.ro>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The commits below broke compilation when
CONFIG_IWLWIFI_DEBUGFS is not set.
FIx that.
Fixes: ddf89ab10a ("iwlwifi: mvm: allow to force the Rx chains from debugfs")
Fixes: 9d761fd8a5 ("iwlwifi: mvm: add trigger for firmware dump upon missed beacons")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently scan params structure has only active or passive dwell time
fields, passive one is used for fragmented scans too. FW needs the
passive dwell time even when performing fragmented scan for calculating
time between channels. Add a separate parameter for fragmented dwell time
and pass both fragmented and passive to FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Lots of issues can be caught when the RSSI drops. Add the
ability to collect the firmware data at that point.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It can be very useful to monitor the statistics and trigger
a firmware dump when a certain value hits a certain offset.
Since the statistics are huge, add a generic trigger. When
the DWORD at offset X reaches value Y.
Since there is another trigger before this one I can't add
right now because of a dependency on mac80211, add a
reserved entry to keep the enum in place.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes the firmware will have a hard coded configuration.
In this case, the driver won't find any configuration
in the firmware file, and it will have to re-start
recording in case it has been stopped. This can't be done
by the configuration host command since there is no such
host command configured. Do that with the registers instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to collect the data as soon the firmware
sends a specific notification of command response.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We fire the trigger when the channel switch starts, but
the delay is configurable. That makes is easier to catch
channel switches that fail.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Missing beacons is a good indication that something is going
wrong in the firmware. Add a trigger to be able to collect
data when we start missing beacons with a configurable
threshold.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Now that the firmware dump can be triggered by events in
the code and not only the user or an firmware ASSERT, we
need a way to know why the firmware dump was triggered.
Add a section in the dump file for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Most of the time, the issues we want to debug with the
firmware dump mechanism are transient. It is then very
hard to stop the recording on time and get meaningful
data.
In order to solve this, I add here an infrastucture
of triggers. The user will supply a list of triggers
that will start / stop the recording. We have two types
of triggers: start and stop. Start triggers can start a
specific configuration. The stop triggers will be able to
kick the collection of the data with the currently running
configuration. These triggers are given to the driver by
the .ucode file - just like the configuration.
In the next patches, I'll add triggers in the code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
20 ms fragments are no longer required by system.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Packet Level Co-Running is a BT Coex feature which is
supported on certain devices only, hence the need for
a TLV flag for it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense. Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).
To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reported-by: Samuel Tan <samueltan@chromium.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The new API slightly changes the layout of the version of
the firmware - prepare for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Report the average beacon signal and the number of received beacons as
measured by the firmware.
Since the firmware just counts, and doesn't reset the counter at all,
clear it in the firmware whenever we associate. However, accumulate it
over firmware restart.
Since clearing the statistics in the firmware will also clear the ones
for the radio statistics, add those to the accumulator when cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Due to HW bug in the DBGC when driver want to stop the dbg recording it
should wait 100us before collecting the data instead of write 0 to
DBGC_OUT_CTRL.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions. Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This firmware is not supported anymore. Stop loading this firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New firmware versions will report statistics using a new version 10
of the API, instead of the current version 8. Add support for this.
This enables getting beacon and radio statistics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to use the firmware debugging system even when
the configuration values are set hard coded in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The shared antenna should be forbidden to use only if there's
high BT activity. Comparing to BT_OFF was effectively causing
us to always forbid using the shared antenna for SISO. This
leads to degraded performance in scenarios where the shared
antenna would have better performance.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add this to the info printed when reading rate_scale_table.
Useful for debugging.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ss_force is a debugging option to force a certain single stream
tx mode. It's not useful if it gets reset after tx idle. Fix that.
While at it also make sure any code touching ss_force will only
get compiled if debugfs support is configured.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer devices have more PAPD channel groups.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When a TDLS station is being drained its Tx queues are still in use. Don't
allocate them to a different station in the meantime.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Due to issues with Miracast adapters MIMO reception disable
use of MIMO when for low latency P2P traffic.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Once the FW supports autonomous decision between STBC/BFER/SISO
we no longer set the STBC bit and ANT_AB in the rate table.
However the FW rate in the tx response will have the STBC
or BFER bit set and the antennas set to ANT_AB in case these
were chosen by it. This will cause us to discard any such
response as unmatching the current LQ table and thus break
the rs search cycle completely.
Fix this by relaxing the rate matching in case we're working
with the new API and STBC/BFER are used.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The check to avoid the shared antenna was passed the wrong
antenna parameter. It should have checked whether the antenna of
the next column we're considering is allowed and instead it was
passed the current antenna.
This could lead to a wrong choice of the next column in the rs
algorithm and non optimal performance.
Fixes: commit 219fb66b49 ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high")
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently rs uses the info in mac80211 tx status which is
a translation of the actual rate coming up from the FW in
the tx response. This is matched up against the LQ table first
rate to make sure this tx frame used the current LQ table.
Instead of using the translated mac80211 info it's easier and
cleaner to just pass the actual tx response rate in the driver
private data and use that for matching.
This becomes even more important once the FW begins to
decide on its own whether to use STBC/BFER/SISO.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
yet-another-livelock in raid5, and a problem with write errors
to 4K-block devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1BWV
-----END PGP SIGNATURE-----
Merge tag 'md/3.20-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Three bug md fixes for 3.20
yet-another-livelock in raid5, and a problem with write errors to
4K-block devices"
* tag 'md/3.20-fixes' of git://neil.brown.name/md:
md/raid5: Fix livelock when array is both resyncing and degraded.
md/raid10: round up to bdev_logical_block_size in narrow_write_error.
md/raid1: round up to bdev_logical_block_size in narrow_write_error
not be able to decide that an event should not be logged
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jAUs
-----END PGP SIGNATURE-----
Merge tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull mcelog regression fix from Tony Luck:
"Fix regression - functions on the mce notifier chain should not be
able to decide that an event should not be logged"
* tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Fix regression. All error records should report via /dev/mcelog
the staging tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CA9p
-----END PGP SIGNATURE-----
Merge tag 'docs-fix' of git://git.lwn.net/linux-2.6
Pull DocBook build fix from Jonathan Corbet:
"Fix the DocBook build failure caused by the move of the i2o subsystem
to the staging tree"
* tag 'docs-fix' of git://git.lwn.net/linux-2.6:
Fix docs build failure caused by i2o removal
Pull nfsd bugfixes from Bruce Fields:
"These are fixes for two bugs introduced during the merge window"
* 'for-3.20' of git://linux-nfs.org/~bfields/linux:
nfsd4: fix v3-less build
nfsd: fix comparison in fh_fsid_match()
Commit a7854487cd:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd
Cc: stable@vger.kernel.org (v3.7+)
Pull lazytime mount option support from Al Viro:
"Lazytime stuff from tytso"
* 'lazytime' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext4: add optimization for the lazytime mount option
vfs: add find_inode_nowait() function
vfs: add support for a lazytime mount option
Pull iov_iter updates from Al Viro:
"More iov_iter work - missing counterpart of iov_iter_init() for
bvec-backed ones and vfs_read_iter()/vfs_write_iter() - wrappers for
sync calls of ->read_iter()/->write_iter()"
* 'iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: add vfs_iter_{read,write} helpers
new helper: iov_iter_bvec()
Pull getname/putname updates from Al Viro:
"Rework of getname/getname_kernel/etc., mostly from Paul Moore. Gets
rid of quite a pile of kludges between namei and audit..."
* 'getname2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
audit: replace getname()/putname() hacks with reference counters
audit: fix filename matching in __audit_inode() and __audit_inode_child()
audit: enable filename recording via getname_kernel()
simpler calling conventions for filename_mountpoint()
fs: create proper filename objects using getname_kernel()
fs: rework getname_kernel to handle up to PATH_MAX sized filenames
cut down the number of do_path_lookup() callers
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
Pull misc VFS updates from Al Viro:
"This cycle a lot of stuff sits on topical branches, so I'll be sending
more or less one pull request per branch.
This is the first pile; more to follow in a few. In this one are
several misc commits from early in the cycle (before I went for
separate branches), plus the rework of mntput/dput ordering on umount,
switching to use of fs_pin instead of convoluted games in
namespace_unlock()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch the IO-triggering parts of umount to fs_pin
new fs_pin killing logics
allow attaching fs_pin to a group not associated with some superblock
get rid of the second argument of acct_kill()
take count and rcu_head out of fs_pin
dcache: let the dentry count go down to zero without taking d_lock
pull bumping refcount into ->kill()
kill pin_put()
mode_t whack-a-mole: chelsio
file->f_path.dentry is pinned down for as long as the file is open...
get rid of lustre_dump_dentry()
gut proc_register() a bit
kill d_validate()
ncpfs: get rid of d_validate() nonsense
selinuxfs: don't open-code d_genocide()
Merge yet more updates from Andrew Morton:
- a pile of minor fs fixes and cleanups
- kexec updates
- random misc fixes in various places: vmcore, rbtree, eventfd, ipc, seccomp.
- a series of python-based kgdb helper scripts
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
seccomp: cap SECCOMP_RET_ERRNO data to MAX_ERRNO
samples/seccomp: improve label helper
ipc,sem: use current->state helpers
scripts/gdb: disable pagination while printing from breakpoint handler
scripts/gdb: define maintainer
scripts/gdb: convert CpuList to generator function
scripts/gdb: convert ModuleList to generator function
scripts/gdb: use a generator instead of iterator for task list
scripts/gdb: ignore byte-compiled python files
scripts/gdb: port to python3 / gdb7.7
scripts/gdb: add basic documentation
scripts/gdb: add lx-lsmod command
scripts/gdb: add class to iterate over CPU masks
scripts/gdb: add lx_current convenience function
scripts/gdb: add internal helper and convenience function for per-cpu lookup
scripts/gdb: add get_gdbserver_type helper
scripts/gdb: add internal helper and convenience function to retrieve thread_info
scripts/gdb: add is_target_arch helper
scripts/gdb: add helper and convenience function to look up tasks
scripts/gdb: add task iteration class
...
The value resulting from the SECCOMP_RET_DATA mask could exceed MAX_ERRNO
when setting errno during a SECCOMP_RET_ERRNO filter action. This makes
sure we have a reliable value being set, so that an invalid errno will not
be ignored by userspace.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call __set_current_state() instead of assigning the new state directly.
These interfaces also aid CONFIG_DEBUG_ATOMIC_SLEEP environments, keeping
track of who changed the state.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
