The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so add compatible
for Allwinner A64 with uninitialized has_mod_clk driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-6-jagan@amarulasolutions.com
regmap has special API to enable the controller bus clock while
initializing register space, and current driver is using
devm_regmap_init_mmio_clk which require to specify bus
clk_id argument as "bus"
But, the usage of clocks are varies between different Allwinner
DSI controllers. Clocking in A33 would need bus and mod clocks
where as A64 would need only bus clock.
Since A64 support only single bus clock, it is optional to
specify the clock-names on the controller device tree node.
So using NULL on clk_id would get the attached clock.
To support clk_id as "bus" and "NULL" during clock enablement
between controllers, this patch add generic code to handle
the bus clock using regmap_mmio_attach_clk with associated
regmap APIs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-5-jagan@amarulasolutions.com
As per the user manual, look like mod clock is not mandatory
for all Allwinner MIPI DSI controllers, it is connected to
CLK_DSI_SCLK for A31 and not available in A64.
So, add compatible check for A31 and get mod clock accordingly.
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-4-jagan@amarulasolutions.com
The MIPI DSI PHY controller on Allwinner A64 is similar
on the one on A31.
Add A64 compatible and append A31 compatible as fallback.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-3-jagan@amarulasolutions.com
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so it is valid
to have separate compatible for A64 on the same driver.
DSI_SCLK uses mod clock-names on dt-bindings, so the same
is not required for A64.
On that note
- A64 require minimum of 1 clock like the bus clock
- A33 require minimum of 2 clocks like both bus, mod clocks
So, update dt-bindings so-that it can document both A33,
A64 bindings requirements.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-2-jagan@amarulasolutions.com
The pin control must be set to default as soon as possible to
establish a good video link between tv & bridge hdmi
(encoder mode set is call before encoder enable).
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1574850218-13257-1-git-send-email-yannick.fertre@st.com
Jani has merged a new set of logging functions, which we hope to be
the One True solution now, pinky promises:
commit fb6c7ab871
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Dec 10 14:30:43 2019 +0200
drm/print: introduce new struct drm_device based logging macros
Update the todo entry to match the new preference.
v2: Fix spelling issue Sam noticed.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219161722.2779994-1-daniel.vetter@ffwll.ch
At this point in time, compatible string "thine,thc63lvdm83d" is
backed by the lvds-codec driver, and the documentation contained
in thine,thc63lvdm83d.txt is basically the same as the one
contained in lvds-codec.yaml (generic fallback compatible string
aside), therefore absorb thine,thc63lvdm83d.txt.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <1573660292-10629-14-git-send-email-fabrizio.castro@bp.renesas.com
The DS90CF384A from TI is a transparent LVDS receiver (decoder),
and therefore it is compatible with the lvds-codec driver and
bindings.
Document the ti,ds90cf384a compatible string with the dt-bindings.
No driver change required.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-10-git-send-email-fabrizio.castro@bp.renesas.com
In an effort to repurpose lvds-encoder.c to also serve the
function of LVDS decoders, we ended up defining a new "generic"
compatible string ("lvds-decoder"), therefore adapt the dt schema
to allow for the new compatible string.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[narmstrong: fixed port descriptions as acked with lpinchart]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-9-git-send-email-fabrizio.castro@bp.renesas.com
The probe function needs to get ahold of the panel device tree
node, and it achieves that by using a combination of
of_graph_get_port_by_id, of_get_child_by_name, and
of_graph_get_remote_port_parent. We can achieve the same goal
by replacing those calls with a call to of_graph_get_remote_node
these days.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-8-git-send-email-fabrizio.castro@bp.renesas.com
Add support for transparent LVDS decoders by adding a new
compatible string ("lvds-decoder") to the driver.
This patch also adds member connector_type to struct lvds_codec,
and that's because LVDS decoders have a different connector type
from LVDS encoders. We fill this new member up with the data
matching the compatible string.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Fix pointer to int cast warning]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217230753.2999-1-laurent.pinchart+renesas@ideasonboard.com
lvds-encoder.c implementation is also suitable for LVDS decoders,
not just LVDS encoders.
Instead of creating a new driver for addressing support for
transparent LVDS decoders, repurpose lvds-encoder.c for the greater
good with this patch.
This patch only "rebrands" the lvds-encoder.c driver, to make it
suitable for hosting LVDS decoders support. The actual support for
LVDS decoders will come with a later patch.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-6-git-send-email-fabrizio.castro@bp.renesas.com
Compatible string "ti,sn75lvds83" is being used by device tree
rk3188-bqedison2qc.dts, but it's not documented anywhere, therefore
document it within lvds-transmitter.yaml.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-5-git-send-email-fabrizio.castro@bp.renesas.com
ti,ds90c185.txt documents LVDS encoders using the same driver
as the one documented by lvds-transmitter.yaml.
Since the properties listed in ti,ds90c185.txt are the same
as the ones listed in lvds-transmitter.yaml, absorb the dt-binding
into lvds-transmitter.yaml.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-4-git-send-email-fabrizio.castro@bp.renesas.com
I'm just going to put Chia's review comment here since it sums
the issue rather nicely:
"(1) Semantically, a dma-buf is in DMA domain. CPU access from the
importer must be surrounded by {begin,end}_cpu_access. This gives the
exporter a chance to move the buffer to the CPU domain temporarily.
(2) When the exporter itself has other means to do CPU access, it is
only reasonable for the exporter to move the buffer to the CPU domain
before access, and to the DMA domain after access. The exporter can
potentially reuse {begin,end}_cpu_access for that purpose.
Because of (1), udmabuf does need to implement the
{begin,end}_cpu_access hooks. But "begin" should mean
dma_sync_sg_for_cpu and "end" should mean dma_sync_sg_for_device.
Because of (2), if userspace wants to continuing accessing through the
memfd mapping, it should call udmabuf's {begin,end}_cpu_access to
avoid cache issues."
Reported-by: Chia-I Wu <olvaffe@gmail.com>
Suggested-by: Chia-I Wu <olvaffe@gmail.com>
Fixes: 284562e1f3 ("udmabuf: implement begin_cpu_access/end_cpu_access hooks")
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20191217230228.453-1-gurchetansingh@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The video DSI mode had not really been tested. These fixes makes
it more likely to work on real hardware:
- Put the active width (x width) in the right bits and the VSA
(vertical sync active) in the right bits (those were swapped).
- Calculate the packet sizes in bytes as in the vendor driver,
rather than in bits. Test the calculations agains a
spreadsheet and confirmed by debug prints to be reasonable.
- Also verified the register values with relative confidence
to register dumps from the Samsung GT-I8190 boot loader
graphics. We are not identical but not off by far either.
- Error out if the current mode and refresh frequency doesn't
work out. (In the future we may simply want to scale down
the vrefresh.)
- Handle negative result in front/back/sync packages and fall
back to zero like in the vendor driver.
- Put in lots of clarifying comments and references to the
documentation where the code is hard to understand.
- Set the DSI_VID_VCA_SETTING2 field
DSI_VID_VCA_SETTING2_MAX_LINE_LIMIT to blkline_pck - 6 as in
the vendor driver and mask the field properly.
- Set the DSI_VID_VCA_SETTING1 field
DSI_VID_VCA_SETTING1_MAX_BURST_LIMIT to blkeol_pck - 6 to
blkeol_duration - 6 as in the vendor driver.
Cc: Stephan Gerhold <stephan@gerhold.net>
Fixes: 5fc537bfd0 ("drm/mcde: Add new driver for ST-Ericsson MCDE")
Link: https://patchwork.freedesktop.org/patch/msgid/20191217150959.17215-1-linus.walleij@linaro.org
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The initial commit followed by the fix didn't
take into consideration the case:
CONFIG_DRM_PANEL=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_DRM_I915=y
where symbol devm_of_find_backlight() is not reachable from DRM subsystem.
Quick fix is to avoid drm_panel_of_backlight() from exporting in such case.
Fixes: 907aa265fd ("drm/drm_panel: fix EXPORT of drm_panel_of_backlight")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217140721.42432-1-andriy.shevchenko@linux.intel.com
Fix the following sparse warning.
drivers/dma-buf/dma-heap.c:109:14: warning: symbol 'dma_heap_ioctl_cmds'
was not declared. Should it be static?
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
[sumits: rebased over IOCTL rename patches]
Link: https://patchwork.freedesktop.org/patch/msgid/20191217190822.1969-1-sumit.semwal@linaro.org
The -ENOTTY error return path does not free the allocated
kdata as it returns directly. Fix this by returning via the
error handling label err.
Addresses-Coverity: ("Resource leak")
Fixes: c02a81fba7 ("dma-buf: Add dma-buf heaps framework")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216161059.269492-1-colin.king@canonical.com
In drm_dev_init, parent is checked for NULL via assert after
checked in devm_drm_dev_init(). The patch removes the duplicate
check and replaces the assertion with WARN_ON. Further, it returns
-EINVAL consistent with the usage in devm_drm_dev_init.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191215194345.4679-1-pakki001@umn.edu
Checking both is one too much, so wrap a WARN_ON around it to stope
the copypasta.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213172612.1514842-2-daniel.vetter@ffwll.ch
I'll add more fancy logic to them soon, so everyone really has to use
them. Plus they already provide some nice additional debug
infrastructure on top of direct ww_mutex usage for the fences tracked
by dma_resv.
v2: Fix the lost _interruptible (Michael)
Acked-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: etnaviv@lists.freedesktop.org
Cc: "Ruhl, Michael J" <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191214000927.1616384-1-daniel.vetter@ffwll.ch
I'll add more fancy logic to them soon, so everyone really has to use
them. Plus they already provide some nice additional debug
infrastructure on top of direct ww_mutex usage for the fences tracked
by dma_resv.
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191125094356.161941-5-daniel.vetter@ffwll.ch
The heaps are already in a directory of heaps, adding _heap to a heap
name is redundant. This patch is only a name change, no logic is changed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216133405.1001-3-afd@ti.com
This is more consistent with the DMA and DRM frameworks convention. This
patch is only a name change, no logic is changed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216133405.1001-2-afd@ti.com
Add new struct drm_device based logging macros modeled after the core
kernel device based logging macros. These would be preferred over the
drm printk and struct device based macros in drm code, where possible.
We have existing drm specific struct device based logging functions, but
they are too verbose to use for two main reasons:
* The names are unnecessarily long, for example DRM_DEV_DEBUG_KMS().
* The use of struct device over struct drm_device is too generic for
most users, leading to an extra dereference.
For example:
DRM_DEV_DEBUG_KMS(drm->dev, "Hello, world\n");
vs.
drm_dbg_kms(drm, "Hello, world\n");
It's a matter of taste, but the SHOUTING UPPERCASE has been argued to be
less readable than lowercase.
Some names are changed from old DRM names to be based on the core kernel
logging functions. For example, NOTE -> notice, ERROR -> err, DEBUG ->
dbg.
Due to the conflation of DRM_DEBUG and DRM_DEBUG_DRIVER macro use
(DRM_DEBUG is used widely in drivers though it's supposed to be a core
debugging category), they are named as drm_dbg_core and drm_dbg,
respectively.
The drm_err and _once/_ratelimited variants no longer include the
function name in order to be able to use the core device based logging
macros. Arguably this is not a significant change; error messages should
not be so common to be only distinguishable by the function name.
Ratelimited debug logging macros are to be added later.
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Sean Paul <sean@poorly.run>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210123050.8799-1-jani.nikula@intel.com
We depend on a specific relationship between the VIC number and the
index in the CEA mode arrays. Assert that the arrays have the expected
size to make sure we've not accidentally left holes in them.
v2: Pimp the BUILD_BUG_ON()s
v3: Fix typos (Manasi)
Cc: Hans Verkuil <hansverk@cisco.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213174348.27261-5-ville.syrjala@linux.intel.com
Now that the cea mode handling is not 100% tied to the single
array the dummy VIC 0 mode is pretty much pointles. Throw it
out.
v2: Rebase
Cc: Tom Anderson <thomasanderson@google.com>
Cc: Hans Verkuil <hansverk@cisco.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213174348.27261-4-ville.syrjala@linux.intel.com
Reviewed-by: Thomas Anderson <thomasanderson@google.com>
Add a second table to the cea modes with VIC >= 193.
v2: Improve the comment for cea_modes_*[] to indicate
that one should always use cea_mode_for_vic() (Tom)
Cc: Hans Verkuil <hansverk@cisco.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213174348.27261-3-ville.syrjala@linux.intel.com
We're going to need two cea mode tables (one for VICs < 128,
another one for VICs >= 193). To that end replace the direct
edid_cea_modes[] lookups with a function call. And we'll rename
the array to edid_cea_modes_0[] to indicate how it's to be
indexed.
v2: Fix typos (Tom)
Drop the pointless NULL checks in the loops (Tom)
Assign when declaring (Tom)
Improve the comment for cea_modes_*[] to indicate
that one should always use cea_mode_for_vic() (Tom)
Cc: Tom Anderson <thomasanderson@google.com>
Cc: Hans Verkuil <hansverk@cisco.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213174348.27261-2-ville.syrjala@linux.intel.com
Reviewed-by: Thomas Anderson <thomasanderson@google.com>
