Let v4l2_ctrl_subscribe_event() do the job for other types except
V4L2_EVENT_SOURCE_CHANGE.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Settle time determines the number of cil clock cyles to wait after
LP00 when moving from LP to HS.
This patch computes T-CLK-SETTLE and T-HS-SETTLE times based on cil
clock rate and pixel rate from the sensor and programs them during
streaming.
T-CLK-SETTLE time is the interval during which receiver will ignore
any HS transitions on clock lane starting from the beginning of
T-CLK-PREPARE.
T-HS-SETTLE time is the interval during which recevier will ignore
any HS transitions on data lane starting from the beginning of
T-HS-PREPARE.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CSI MIPI pads need to be enabled and calibrated for capturing from
the external sensor or transmitter.
MIPI CAL unit calibrates MIPI pads pull-up, pull-down and termination
impedances. Calibration is done by co-work of MIPI BIAS pad and MIPI
CAL control unit.
Triggering calibration start can happen any time after MIPI pads are
enabled but calibration results will be latched and applied to MIPI
pads by MIPI CAL unit only when the link is in LP11 state and then
calibration status register gets updated.
This patch enables CSI MIPI pads and calibrates them during streaming.
Tegra CSI receiver is able to catch the very first clock transition.
So, CSI receiver is always enabled prior to sensor streaming and
trigger of calibration start is done during CSI subdev streaming and
status of calibration is verified after sensor stream on.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the split of MIPI calibration into tegra_mipi_calibrate() and
tegra_mipi_wait(), MIPI clock is not kept enabled and mutex is not locked
till the calibration is done.
So, this patch keeps MIPI clock enabled and mutex locked after triggering
start of calibration till its done.
To let calibration process go through its finite sequence codes before
calibration logic waiting for pads idle state added wait time of 75usec
to make sure it sees idle state to apply the results.
This patch renames tegra_mipi_calibrate() as tegra_mipi_start_calibration()
and tegra_mipi_wait() as tegra_mipi_finish_calibration() to be inline
with their usage.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds selection v4l2 ioctl operations to allow configuring
a selection rectangle in the sensor through the Tegra video device
node.
Some sensor drivers supporting crop uses try_crop rectangle from
v4l2_subdev_pad_config during try format for computing binning.
So with selection ops support, this patch also updates try format
to use try crop rectangle either from subdev frame size enumeration
or from subdev crop boundary.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds support to capture from the external sensor
based on device graph in the device tree.
Driver walks through the device graph to create media links
between the entities and registers and unregisters video devices
when the corresponding sub-devices are bound and unbound.
Channel formats are enumerated based on available formats from
the sensor and the corresponding matched formats from the Tegra
supported video formats list.
Each Tegra CSI instance can be configured as 4-lane or 2-lane
based on supported lane configuration from the sensor through
the device tree.
Currently this driver supports V4L2 video node centric only.
[hverkuil: changed video_unregister_device to vb2_video_unregister_device]
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch separates implementation of CSI stream enable and disable
into separate functions for readability.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Update VI and CSI bindings to add port and endpoint nodes as per
media video-interfaces DT binding document.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tegra VI supported video formats are more for non TPG and there
can be multiple pixel formats for the same media bus format.
This patch updates the helper function for format lookup based on
mbus code from pre-defined Tegra supported format list to look from
the specified list index offset.
Offset based look up is used with sensor device graph (non TPG)
where format enumeration can list all supported formats for the
specific sensor mbus codes.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tegra internal TPG mode is only for Tegra vi and csi testing
without a real sensor and driver should default support real
sensor.
So, This patch adds CONFIG_VIDEO_TEGRA_TPG and enables Tegra
internal TPG mode only when this config is selected.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Pixel format width is mistakenly aligned to surface align bytes
and altering width to aligned value may force sensor mode change
other than the requested one and also cause mismatch in width
programmed between sensor and vi which can lead to capture errors.
This patch removes width alignment and clamps width as per Tegra
minimum and maximum limits.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is only needed for drivers that do not use vb2_fop_release().
Note that vb2_queue_release() is *not* the counterpart of vb2_queue_init()
as some drivers here seem to think.
Also use vb2_video_unregister_device() to automatically stop streaming
at unregister time for those drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is only needed for drivers that do not use vb2_fop_release().
Note that vb2_queue_release() is *not* the counterpart of vb2_queue_init()
as some drivers here seem to think.
Also use vb2_video_unregister_device() to automatically stop streaming
at unregister time for those drivers that set vdev->queue.
Note that sun4i-csi didn't unregister the video device at all. That's
now fixed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a driver calls (_)vb2_fop_release(), then such a driver should also
call vb2_video_unregister_device() instead of video_unregister_device().
This helper will call vb2_queue_release() if a filehandle is marked as
owner of the queue. This ensures that at unregister time any streaming
is cancelled and all buffers are returned to userspace.
This is very useful for complex drivers since this stops all streaming
in all subdevs in the pipeline controlled by this video device. Otherwise
this would be delayed until the owner filehandle is closed, which can be
quite some time later.
Bonus points for ordering the includes :-)
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The files maintained as part of the RDACM20 were incorrectly sorted
while they were added.
Correct the sort-order.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This small change adds the device identifier for the MyGica iGrabber,
which features an Empia EM2860, a Philips SAA7113, Empia EMP202, and
no tuner. Verified that both the composite and S-Video inputs work
with NTSC source. It does not appear to need any port twiddling on
pre-init.
Signed-off-by: Christopher Snowhill <chris@kode54.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis reports this problem
tuner-simple.c:714:13: warning: Assigned value is
garbage or undefined
buffer[1] = buffer[3];
^ ~~~~~~~~~
In simple_set_radio_freq buffer[3] used to be done
in-function with a switch of tuner type, now done
by a call to simple_radio_bandswitch which has this case
case TUNER_TENA_9533_DI:
case TUNER_YMEC_TVF_5533MF:
tuner_dbg("This tuner doesn't ...
return 0;
which does not set buffer[3]. In the old logic, this case
would have returned 0 from simple_set_radio_freq.
Recover this old behavior by returning an error for this
codition. Since the old simple_set_radio_freq behavior
returned a 0, do the same.
Fixes: c7a9f3aa1e ("V4L/DVB (7129): tuner-simple: move device-specific code into three separate functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Setting `hue` by calling tpg_s_hue() directly is risky, since it does not
perform range check. Clamp `hue` to the valid range in tpg_s_hue().
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vivid_meta_out_process() is setting `brightness`, `contrast`, `saturation`
and `hue` using tpg_s_*(). This is wrong, since tpg_s_*() do not provide
range checks. Using tpg_s_*() here also makes the control framework
out-of-sync with the actual values. Use v4l2_ctrl_s_ctrl() instead.
This issue has been reported by syzbot as an out-of-bounds read bug in
precalculate_color().
Reported-and-tested-by: syzbot+02d9172bf4c43104cd70@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=02d9172bf4c43104cd70
Fixes: 746facd393 ("media: vivid: Add metadata output support")
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Kconfig help text for VIDEO_MEDIATEK_VCODEC was referring to a
single module named mtk-vcodec, while this driver produces two modules
named mtk-vcodec-dec and mtk-vcodec-enc. Fix that.
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pvr2_std_str_to_id() returns 0 on failure and 1 on success,
however the caller is checking failure case using <0
Acked-by: Mike Isely <isely@pobox.com>
Co-developed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to [1], there has been no email related to videobuf2 posted
from him to the linux-media mailing list since Apr 2015.
Note: The linked archive seems to lack messages newer than the middle of
2019, but it is the only archive that offers search by name. A manual
look through the messages after that time confirms the observation.
[1] https://www.mail-archive.com/search?a=1&l=linux-media%40vger.kernel.org&haswords=&x=0&y=0&from=Pawel+Osciak&subject=&datewithin=1d&date=¬words=&o=newest
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to [1], there has been no email posted from him to the
linux-media mailing list since Feb 2013.
Note: The linked archive seems to lack messages newer than the middle of
2019, but it is the only archive that offers search by name. A manual
look through the messages after that time confirms the observation.
[1] https://www.mail-archive.com/search?a=1&l=linux-media%40vger.kernel.org&haswords=&x=7&y=20&from=Kyungmin+Park&subject=&datewithin=1d&date=¬words=&o=newest
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tomasz is the most active member from the people listed currently in the
MAINTAINERS file, but is currently listed as a reviewer. Change the
entry into a maintainer and move to the top of the list.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The default RGB quantization range for BT.2020 is full range (just as for
all the other RGB pixel encodings), not limited range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT macro and documentation
accordingly.
Also mention that HSV is always full range and cannot be limited range.
When RGB BT2020 was introduced in V4L2 it was not clear whether it should
be limited or full range, but full range is the right (and consistent)
choice.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The documentation reported service_set as a __u32, but according to
videodev2.h it is a __u16. Correct the documentation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to add OPP tables and perf voting on the OPP powerdomain.
This is needed so venus votes on the corresponding performance state
for the OPP powerdomain along with setting the core clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Post a successful pm_ops->core_get, an error in probe
should exit by doing a pm_ops->core_put which seems
to be missing. So fix it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For other error
paths after this call, things are the same.
Fix this by adding pm_runtime_put_noidle() after 'err_runtime_disable'
label. But in this case, the error path after pm_runtime_put_sync()
will decrease PM usage counter twice. Thus add an extra
pm_runtime_get_noresume() in this path to balance PM counter.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the newly introduced get_mbus_config() subdevice pad operation to
retrieve the remote subdevice MIPI CSI-2 bus configuration and configure
the number of active data lanes accordingly.
In order to be able to call the remote subdevice operation cache the
index of the remote pad connected to the single CSI-2 input port.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the newly introduced get_mbus_config operation to report the
number of currently used data lanes on the MIPI CSI-2 interface.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When outputting SD-Core output through the TXA MIPI CSI-2 interface,
the number of enabled data lanes should be reduced in order to guarantee
that the two video formats produced by the SD-Core (480i and 576i)
generate a MIPI CSI-2 link clock frequency compatible with the MIPI D-PHY
specifications.
Limit the number of enabled data lanes to 2, which is guaranteed to
support 480i and 576i formats.
Cache the number of enabled data lanes to be able to report it through
the new get_mbus_config operation.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Update the TODO entry that mentioned a potential use case for the now
removed g_mbus_config video operation.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the removal of the legacy g_mbus_config and s_mbus_config video
operations, the sole users of V4L2_MBUS_* flags are now the newly
introduced get_mbus_config and set_mbus_config pad operations.
As the semantic of the new operations differs from the semantic of
the legacy ones, add a usage note in the v4l2-mediabus.h header to
specify how to use the flags.
Also add a TODO note to record that we intend to replace the existing
flags with fields, to prevent users from mixing conflicting values
in a single operation call.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With all sensor and platform drivers now converted to use the new
get_mbus_config and set_mbus_config pad operations, remove the
deprecated video operations g_mbus_config and s_mbus_config.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the PXA camera driver to use the new set_mbus_config pad operation.
For this platform the change is not only cosmetic, as the pxa driver is
currently the only driver in mainline to make use of the g_mbus_config
and s_mbus_config video operations.
The existing driver semantic is the following:
- Collect all supported mbus config flags from the remote end
- Match them with the supported PXA mbus configuration flags
- If the remote subdevice allows multiple options for for VSYNC, HSYNC
and PCLK polarity, use platform data requested settings
The semantic of the new get_mbus_config and set_mbus_config differs from
the corresponding video ops, particularly in the fact get_mbus_config
reports the current mbus configuration and not the set of supported
configuration options, with set_mbus_config always reporting the actual
mbus configuration applied to the remote subdevice.
Adapt the driver to perform the following
- Set the remote subdevice mbus configuration according to the PXA
platform data preferences.
- If the applied configuration differs from the requested one (i.e. the
remote subdevice does not allow changing one setting) make sure that
- The remote end does not claim for DATA_ACTIVE_LOW, which seems not
supported by the platform
- The bus mastering roles match
While at there remove a few checks performed on the media bus
configuration at get_format() time as they do not belong there.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the new get_mbus_config and set_mbus_config pad operations in place
of the video operations currently in use.
Compared to other drivers where the same conversion has been performed,
ov6650 proved to be a bit more tricky, as the existing g_mbus_config
implementation did not report the currently applied configuration but
the set of all possible configuration options.
Adapt the driver to support the semantic of the two newly introduced
operations:
- get_mbus_config reports the current media bus configuration
- set_mbus_config applies only changes explicitly requested and updates
the provided cfg parameter to report what has actually been applied to
the hardware.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the existing users of the g_mbus_config video operation to use the
newly introduced get_mbus_config pad operations.
All the ported drivers report a static media bus configuration and do no
support s_mbus_config so the operation implementation has not changed.
Bridge drivers needs to call the new pad operation and will receive an
-ENOICTLCMD when calling the old g_mbus_config video operation
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Introduce two new pad operations to allow retrieving and configuring the
media bus parameters on a subdevice pad.
The newly introduced operations aims to replace the s/g_mbus_config video
operations, which have been on their way for deprecation since a long
time.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=T+fx
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few differerent things in here.
Seems like syzbot got some more io_uring bits wired up, and we got a
handful of reports and the associated fixes are in here.
General fixes too, and a lot of them marked for stable.
Lastly, a bit of fallout from the async buffered reads, where we now
more easily trigger short reads. Some applications don't really like
that, so the io_read() code now handles short reads internally, and
got a cleanup along the way so that it's now easier to read (and
documented). We're now passing tests that failed before"
* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
io_uring: short circuit -EAGAIN for blocking read attempt
io_uring: sanitize double poll handling
io_uring: internally retry short reads
io_uring: retain iov_iter state over io_read/io_write calls
task_work: only grab task signal lock when needed
io_uring: enable lookup of links holding inflight files
io_uring: fail poll arm on queue proc failure
io_uring: hold 'ctx' reference around task_work queue + execute
fs: RWF_NOWAIT should imply IOCB_NOIO
io_uring: defer file table grabbing request cleanup for locked requests
io_uring: add missing REQ_F_COMP_LOCKED for nested requests
io_uring: fix recursive completion locking on oveflow flush
io_uring: use TWA_SIGNAL for task_work uncondtionally
io_uring: account locked memory before potential error case
io_uring: set ctx sq/cq entry count earlier
io_uring: Fix NULL pointer dereference in loop_rw_iter()
io_uring: add comments on how the async buffered read retry works
io_uring: io_async_buf_func() need not test page bit
Commit 1355c31eeb ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.
Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.
Fixes: 1355c31eeb ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.ee
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=10Pr
-----END PGP SIGNATURE-----
Merge tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes on the block side of things:
- Discard granularity fix (Coly)
- rnbd cleanups (Guoqing)
- md error handling fix (Dan)
- md sysfs fix (Junxiao)
- Fix flush request accounting, which caused an IO slowdown for some
configurations (Ming)
- Properly propagate loop flag for partition scanning (Lennart)"
* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
block: fix double account of flush request's driver tag
loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
rnbd: no need to set bi_end_io in rnbd_bio_map_kern
rnbd: remove rnbd_dev_submit_io
md-cluster: Fix potential error pointer dereference in resize_bitmaps()
block: check queue's limits.discard_granularity in __blkdev_issue_discard()
md: get sysfs entry after redundancy attr group create
I collected a single fix during the merge window: we managed to break the early
trap setup on !MMU, this patch fixes it.
The power keeps going on here so I haven't have a chance to give this the
testing I usually would, but I don't have a Kendryte anyway so I doubt I'd pick
up anything subtle even if I was to test. The patch seems pretty safe and it's
still early, so I don't see any reason to let it sit around.
It's fairly late so if it misses the merge window that's not a big deal. I'll
definately have stuff for next week, so I'll just start from whenever this
lands.
-----BEGIN PGP SIGNATURE-----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=+8KT
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fix from Palmer Dabbelt:
"I collected a single fix during the merge window: we managed to break
the early trap setup on !MMU, this fixes it"
* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Setup exception vector for nommu platform
