Since the same nand controller is shared between ARCH_PXA and ARCH_MMP. Move
the pxa3xx_nand.h from mach directory to plat directoy.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Ensure we do not read/write outside array boundaries with a negative index.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since MFP_PIN_GPIO* now includes 128-255, mfp_to_gpio() is no longer
valid for those additional pins, fix it.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some debug information for PXA DMA :
- descriptors queued
- channels state
- global state
--
Since V1: reverted to old register access (no more dma_readl() or dma_writel()).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reduce loop for dma irq handler callbacks to the minimum
required.
Since V1: included suggestion from Nicolas Pitre to improve
even further the loop.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add and initialize the mfp setting of pxa935 chip.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
There is currently an uncovered case for MFP configuration on PXAs which
is selected by setting the PULL_SEL bit but none of the PULL{UP,DOWN}_EN
bits. This case is needed to explicitly let pins float, even if the
selected alternate function would default to a configuration with a pull
resistor enabled.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
As slab is available early now, use kzalloc() rather than
alloc_bootmem_low() in pxa_init_gpio_chip().
This removes the following boot time warning:
<4>------------[ cut here ]------------
<4>WARNING: at mm/bootmem.c:535 alloc_arch_preferred_bootmem+0x2c/0x54()
<d>Modules linked in:
[<c0029430>] (unwind_backtrace+0x0/0xdc) from [<c0036f64>] (warn_slowpath_common+0x4c/0x80)
[<c0036f64>] (warn_slowpath_common+0x4c/0x80) from [<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54)
[<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54) from [<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0)
[<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0) from [<c000f6e4>] (___alloc_bootmem+0xc/0x34)
[<c000f6e4>] (___alloc_bootmem+0xc/0x34) from [<c000cb20>] (pxa_init_gpio+0x48/0x228)
[<c000cb20>] (pxa_init_gpio+0x48/0x228) from [<c0009794>] (init_IRQ+0x34/0x44)
[<c0009794>] (init_IRQ+0x34/0x44) from [<c00089d4>] (start_kernel+0x144/0x264)
[<c00089d4>] (start_kernel+0x144/0x264) from [<a0008034>] (0xa0008034)
<4>---[ end trace 1b75b31a2719ed1c ]---
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa_gpio_irq_type() and pxa_unmask_muxed_gpio() will touch non-muxed GPIOs
(0 and 1 on PXA2xx/PXA3xx) bits in GRERx and GFERx, which is incorrect.
Actually, only those bits should get updated if the corresponding bits are
set in c->irq_mask as well. Fix this by updating only those relevant bits.
Reported-and-tested-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
arch/arm/plat-pxa/mfp.c is not intended to be use by PXA25x/PXA27x,
make it explicit here only for use by PXA3xx or ARCH_MMP.
Reported-by: Guennadi Liakhovestski <g.liakhovestski@gmx.de>
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. add common GPIO handling code into [arch/arm/plat-pxa]
2. common code in <mach/gpio.h> moved into <plat/gpio.h>, new processors
should implement its own <mach/gpio.h>, provide the following required
definitions and '#include <plat/gpio.h>' in the end:
- GPIO_REGS_VIRT for mapped virtual address of the GPIO registers'
physical I/O memory
- macros of GPLR(), GPSR(), GPDR() for constant optimization for
functions gpio_{set,get}_value() (so that bit-bang code can still
have tolerable performance)
- NR_BUILTIN_GPIO for the number of onchip GPIO
- definitions of __gpio_is_inverted() and __gpio_is_occupied(), they
can be either macros or inlined functions
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. introduce folder of 'arch/arm/plat-pxa' for common code across different
PXA processor families
2. initially moved DMA code into plat-pxa
3. common code in <mach/dma.h> moved into <plat/dma.h>, new processors
should implement its own <mach/dma.h>, provide the following required
definitions and '#include <plat/dma.h>' in the end:
- DMAC_REGS_VIRT for mapped virtual address of the DMA registers'
physical I/O memory
Signed-off-by: Eric Miao <eric.miao@marvell.com>
