The boot flags exported through sysfs was wrongly reverted to 2. Use
boot flag 3 required per spec.
Bit 0 Block valid flag
Bit 1 Firmware booting selected
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump mpt3sas driver version to v16.100.00.00
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding PNP ID of Mercator i.e. SAS3616 HBA device. Its device ID is
0xD1 and vendor ID is 0x1000.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enclosure handles are not updated after host reset. As a result, driver
device structure is holding previously assigned enclosure handle which
is different from the enclosure handle populated in the corresponding
device page.
Modified the driver to update devices enclosure handles after host reset
to current value by referring the enclosure handles from corresponding
device pages
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display chassis slot information along with other drive location
parameters such as slot number and connector name in the logs if
chassis slot validity bit is set in 'SAS Enclosure Page 0'.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI headers to v2.00.48
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.
Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Dev Handles whose value is less than HBA's phys count number, driver
would return HBA's SAS address value. As a result, for a Virtual SES
device the driver was returning the HBA's SAS address. Updated the
driver to return Virtual SES' SAS address.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce the memory footprint of the driver in the kdump kernel, we
apply the following settings when reset_devices is set:
1. Use single MSI-x vector.
2. Disable RDPQ mode.
3. Set sg_table_size to 32 by default.
4) Set SCSI IO Queue depth to 200.
[mkp: fixed commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While removing Expander devices, we are removing expander device entry
from the list before freeing its child devices. While freeing child
device we are finding its parent device node as NULL and therefore we
are not freeing the child device's allocated data structures. Updated
the driver to remove the expander device from the list only after
freeing all its child devices.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Earlier Active Cable Exception event with reason code "Cable Degraded
(0x02))" was added only for Active Cable. Now this event is extended to
Passive cable too. Re-arranged display message accordingly.
Also added Cable Exception Event event for SAS3008 & SAS3108 HBAs
(i.e. MPI 2.5 spec supporting HBAs). Previously, this event was enabled
only for MPI 2.6 spec supporting HBA devices.
[mkp: typos]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since we have converted all the user of UFS_BIT() macro with the actual
bit position, let remove unused UFS_BIT()macro.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
HOST_ERROR_INDICATOR and DEVICE_ERROR_INDICATOR are not used
anywhere. Also as per JESD223C specification, bit[7:4] are reserved.
Lets remove these #defines.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use actual bit position instead of UFS_BIT() macro. This patch also
changes bit-17 to meaningful #define.
This change is as per discussion here [1]
[1] -> https://lkml.org/lkml/2017/8/28/786
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently UFS HCI uses UFS_BIT() macro to get various bit position for
the hardware registers status bits. Which makes code longer instead of
shorter. This macro does not improve code readability as well. Lets
re-write these macro definition with the actual bit position.
Suggested-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change version to 11.4.0.4
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The internal cfg flag is actually smaller, by 1 (for a partial page
sge), than the sg list maintained by the driver. Thus the check on sg
segments errored out when it shouldn't have
Ensure the check is +1
Note: having a value that is less than what it really is is bogus.
Correcting it now would be a significant rework. Add this item to the
list to be refactored in the merge with efct.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running NVME io as a NVME host, if the driver is unloaded there
would be oops in lpfc_sli4_issue_wqe.
When unloading, controllers are torn down and the transport initiates
set_property commands to reset the controller and issues aborts to
terminate existing io. The drivers nvme abort and fcp io submit
routines needed to recognize the driver is unloading and fail the new
requests. It didn't, resulting in the oops.
Revise the ls and fcp io submit routines to detect the unloading state
and properly handle their cleanup.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support RDP and Multiple Frames
If the remote Nport is not logged in, the driver would not populate all
the descriptors in the RDP response payload. Doing so would create a
payload length that requires multiple frames due to exceeding the
default rx buffer size without an explicit login. Currently FC-LS
explicitly states the RDP response must be a single frame sequence.
Thus we did not violate the standard.
Recently, a modification to FC-LS was accepted which allows multi-frame
sequences and all vendors have indicated they are interoperable with the
change. As such, extend RDP support with the additional fields and send
a multi-frame sequence.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before releasing nvme io back to the io stack for possible retry on
other paths, ensure the io termination is interlocked with the target
device by ensuring the entire ABTS-LS protocol is complete.
Additionally, FC-NVME ABTS-LS protocol does not use RRQ. Remove RRQ
behavior from ABTS-LS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware update fails with: status x17 add_status x56 on the final write
If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries. Resolve by making all writes be a single 4k page in length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is seeing a NULL pointer in lpfc_nvme_fcp_io_submit. This
was ultimately due to a transport AER being sent on a terminated
controller, thus some of the values were not set. In case we're in a
system without a corrected transport and in case a race condition occurs
where we enter the routine as the teardown is happening in a separate
thread, validate the parameters before starting the io.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The initial implementation of NVME didn't merge with NPIV support. As
such, there are several issues if NPIV is used with NVME. For now,
ensure that if NVME is enabled then NPIV is not enabled.
Support for NPIV with NVME will be added in the near future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
if nvmet targetport registration fails, the driver encounters a NULL
pointer oops in lpfc_hb_timeout_handler.
To fix: if registration fails, ensure nvmet_support is cleared on the
port structure.
Also enhanced the log message on failure.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The descriptions for lpfc_xri_split and lpfc_enable_fc4_type were
poor. Revise for better understanding:
lpfc_xri_split - Percentage of FCP XRI resources versus NVME
lpfc_enable_fc4_type - Enable FC4 Protocol support - FCP / NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Always set ctxp->state to LPFC_NVMET_STE_ABORT if ABORT op gets called
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several log messages that report abnormal terminations that by
default are marked warn. These are typically the result of failures due
to invalid controller state or abort completions. They are all natural
when a controller resets.
Unfortunately, as they are logged by default, it makes the admin very
concerned.
Convert the messages to Info.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is encountering oops in lpfc_sli_calc_ring.
The driver is setting hba_wqidx for FCP based on the policy in use for
NVME. The two may not be the same. Change to set the wqidx based on the
FCP policy.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy target nvme load duration, the lpfc irq handler is
encountering cpu lockup warnings.
Convert the driver to a shortened ISR handler which identifies the
interrupting condition then schedules a workq thread to process the
completion queue the interrupt was for. This moves all the real work
into the workq element.
As nvmet_fc upcalls are no longer in ISR context, don't set the feature
flags
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to make ktime samples more accurate
If ktime is turned on in the middle of an IO, the max calculation could
be misleading. Base sampling on the start time of the IO as opposed to
ktime_on.
Make ISR ktime timestamps be from when CQE is read instead of EQE.
Added additional sanity checks when deciding whether to accept an IO
sample or not.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Warning messages when NVME_TARGET_FC not defined on ppc builds
The lpfc_nvmet_replenish_context() function is only meaningful when NVME
target mode enabled. Surround the function body with ifdefs for target
mode enablement.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a link bounce scenario, a condition can occur where the discovery
engine swaps an ndlp structure (address change for an nport). While the
swap was successfully executed by the discovery engine, the driver did
not properly detect a change in the ndlp bound to the nvme rport. This
error resulted in the nvme host transport issuing an IO to the correct
nvme rport, but the lpfc driver addressed a ndlp with an NLP_UNUSED
status and failed the io. This resulting it it looking like there were
missing namespaces and applications failed due to io errors.
To fix, in lpfc_nvme_register_rport, rework the "rebind" case to break
the nvme rport<->ndlp association when the ndlp already has an
nrport. Then rebind the rport to the correct ndlp data and backpointers.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in a list_add_call
The lookup by tag function will return null if the IOCB is out of range
or does not have the on txcmplq flag set.
Fix: Check for null return from lookup by tag.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in timer management code.
The sli4 remove_one handler is not stoping the timers as it starts to
remove the port so that it can be swapped.
Fix: Stop the timers early in the handler routine.
Note: Fix in SLI-4 only. SLI-3 already stopped the timers properly.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a small cosmetic bug in a very rarely encountered error message that
can occur when a LD has a corrupted raid map.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver's PCI IDs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused variable sas_ha to clean up build warning
"unused variable sas_ha [-Wunused-variable]"
Fixes: 042ebd293b ("scsi: libsas: kill useless ha_event and do some cleanup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the command type of UTRD in UFS 2.1 specification is the same with
UFS 2.0. And it assumes the future UFS specification will follow the
same definition.
Signed-off-by: kehuanlin <kehuanlin@pinecone.net>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several configurable fields of the Device Descriptor and the Unit
Descriptors determine the Boot LUN status. The bBootEnable field and the
bBootLunEn attribute is set to zero by default, so the Boot LUN is
disabled by default.
At which point the scsi device add for Boot LUN will fail, but we can
continue to use the ufs device in fact. This failure shouldn't abort the
device boot.
Signed-off-by: Huanlin Ke <kehuanlin@pinecone.net>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since right after the user copy, we are going to memset(&karg, 0,
sizeof(karg)), the copy_from_user is redundant
Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device handlers are optional, and for some handlers like ALUA only
implemented for certain device types. So suppress any errors for
unsupported devices.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rather than having each device handler implementing their own error
mapping, have the ->attach() call return a SCSI_DH_XXX error code and
implement the mapping in scsi_dh_handler_attach().
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reporting a maximum number of blocks that is not aligned on the device
physical size would cause a large write same request to be split into
physically unaligned chunks by __blkdev_issue_write_zeroes() and
__blkdev_issue_write_same(), even if the caller of these functions took
care to align its request to physical sectors.
Make sure the maximum reported is aligned to the device physical block
size. This is only an optional optimization for regular disks, but this
is mandatory to avoid failure of large write same requests directed at
sequential write required zones of host-managed ZBC disks.
[mkp: tweaked commit message]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
