To be used by mlx5_ib in the following patches for implementing
RAW PACKET QP.
Add mlx5_core_ prefix to alloc and delloc transport_domain since
they are exposed now.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to ensure IB spec atomic correctness in atomic operations, if
HW is configured to host endianness, advertise IB_ATOMIC_HCA. if not,
advertise IB_ATOMIC_NONE.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
HW is capable of 2 requestor endianness modes for standard 8 Bytes
atomic: BE (0x0) and host endianness (0x1). Read the supported modes
from hca atomic capabilities and configure HW to host endianness mode if
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support of cross-channel functionality to mlx5
driver. This includes ability to ignore overrun for CQ
which intended for cross-channel, export device capability and
configure the QP to be sync master/slave queues.
The cross-channel enabled QP supports combination of
three possible properties:
* WQE processing on the receive queue of this QP
* WQE processing on the send queue of this QP
* WQE are supported on the send queue
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pass hca_core_clock_offset to user-space is mandatory in order to
let the user-space read the free-running clock register from the
right offset in the memory mapped page.
Passing this value is done by changing the vendor's command
and response of init_ucontext to be in extensible form.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reporting the hca_core_clock (in kHZ) and the timestamp_mask in
query_device extended verb. timestamp_mask is used by users in order
to know what is the valid range of the raw timestamps, while
hca_core_clock reports the clock frequency that is used for
timestamps.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the address handle and QP address path fields according to the
link layer type (IB/Eth).
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These callbacks write into the mlx5 RoCE address table.
Upon del_gid we write a zero'd GID.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When handling a responder completion, if the link layer is Ethernet,
set the work completion network_hdr_type field according to CQE's
info and the IB_WC_WITH_NETWORK_HDR_TYPE flag.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Using the vport access functions to retrieve the Ethernet
specific information and return this information in
ib_query_device and ib_query_port.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A mlx5 Ethernet port must be explicitly enabled for RoCE.
When RoCE is not enabled on the port, the NIC will refuse to create
QPs attached to it and incoming RoCE packets will be considered by the
NIC as plain Ethernet packets.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f38 ("net/mlx5e: Light-weight netdev open/stop")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On device initialization, wait till firmware indicates that that it is done
with initialization before proceeding to initialize the device.
Also update initialization segment layout to match driver/firmware
interface definitions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the pci_error_handlers for mlx5_core which allow the
driver to recover from PCI error.
Once an error is detected in the PCI, the mlx5_pci_err_detected is called
and it:
1) Marks the device to be in 'Internal Error' state.
2) Dispatches an event to the mlx5_ib to flush all the outstanding cqes
with error.
3) Returns all the on going commands with error.
4) Unloads the driver.
Afterwards, the FW is reset and mlx5_pci_slot_reset is called and it
enables the device and restore it's pci state.
If the later succeeds, mlx5_pci_resume is called, and it loads the SW
stack.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The detection of a fatal condition has been updated to take into account
the state reported by the device or by detecting an all ones read of the
firmware version which indicates that the device is not accessible.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a single threaded work queue for each device in the system instead of
using one thread for any device. This is required so we can concurrently
process system error handling for all the devices that need that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to handling system errors at the mlx5_core level, change the
interface of cmd_work_handler to accept a 64 bit argument for the vector.
This allows to encode a flag that signifies when the handler is called
as a result of a driver logic that wishes to terminate commands that
the hardware may not be able to terminate. Such command completions
are detected at the handler and proper return status is encoded.
To be able to terminate page handler commands, we make sure to set
the corresponding bit in the bitmask.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name refers to syndrome so uset ext_synd instread of ext_sync.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 96249d70dd ("IB/core: Guarantee that a local_dma_lkey
is available") allows ULPs that make use of the local dma key to keep
working as before by allocating a DMA MR with local permissions and
converted these consumers to use the MR associated with the PD
rather then device->local_dma_lkey.
ConnectIB has some known issues with memory registration
using the local_dma_lkey (SEND, RDMA, RECV seems to work ok).
Thus don't expose support for it (remove device->local_dma_lkey
setting), and take advantage of the above commit such that no regression
is introduced to working systems.
The local_dma_lkey support will be restored in CX4 depending on FW
capability query.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing
read and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc. mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHLg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
The mlx5 driver exposes device capability IB_DEVICE_LOCAL_DMA_LKEY
but does not set the the device local_dma_lkey. This breaks
rpcrdma drivers.
Query and set this lkey when creating the device resources.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Only rx/tx pause settings.
Autoneg setting is currently not supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A regular TX WQE execution involves two or more DMA reads -
one to fetch the WQE, and another one per WQE gather entry.
These DMA reads obviously increase the TX latency.
There are two mlx5 mechanisms to bypass these DMA reads:
1) Inline WQE
2) Blue Flame (BF)
An inline WQE contains a whole packet, thus saves the DMA read/s
of the regular WQE gather entry/s. Inline WQE support was already
added in the previous commit.
A BF WQE is written directly to the device I/O mapped memory, thus
enables saving the DMA read that fetches the WQE.
The BF WQE I/O write must be in cache line granularity, thus uses
the CPU write combining mechanism.
A BF WQE I/O write acts also as a TX doorbell for notifying the
device of new TX WQEs.
A BF WQE is written to the same I/O mapped address as the regular TX
doorbell, thus this address is being mapped twice - once by ioremap()
and once by io_mapping_map_wc().
While both mechanisms reduce the TX latency, they both consume more CPU
cycles than a regular WQE:
- A BF WQE must still be written to host memory, in addition to being
written directly to the device I/O mapped memory.
- An inline WQE involves copying the SKB data into it.
To handle this tradeoff, we introduce here a heuristic algorithm that
strives to avoid using these two mechanisms in case the TX queue is
being back-pressured by the device, and limit their usage rate otherwise.
An inline WQE will always be "Blue Flamed" (written directly to the
device I/O mapped memory) while a BF WQE may not be inlined (may contain
gather entries).
Preliminary testing using netperf UDP_RR shows that the latency goes down
from 17.5us to 16.9us, while the message rate (tested with pktgen) stays
the same.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By affinity hints and XPS, each mlx5e channel is assigned a CPU
core.
Channel DMA coherent memory that is written by the NIC and read
by SW (e.g CQ buffer) is allocated on the NUMA node of the CPU
core assigned for the channel.
Channel DMA coherent memory that is written by SW and read by the
NIC (e.g SQ/RQ buffer) is allocated on the NUMA node of the NIC.
Doorbell record (written by SW and read by the NIC) is an
exception since it is accessed by SW more frequently.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Enable HW cacheline start padding and align RX WQE size to cacheline
while considering HW start padding. Also, fix dma_unmap call to use
the correct SKB data buffer size.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cd ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process_mad device function declares some parameters as "in". Make those
parameters const and adjust the call tree under process_mad in the various
drivers accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is the Ethernet part of the driver for the Mellanox ConnectX(R)-4
Single/Dual-Port Adapter supporting 100Gb/s with VPI. The driver
extends the existing mlx5 driver with Ethernet functionality.
This patch contains the driver entry points but does not include
transmit and receive (see the previous patch in the series) routines.
It also adds the option MLX5_CORE_EN to Kconfig to enable/disable the
Ethernet functionality. Currently, Kconfig is programmed to make
Ethernet and Infiniband functionality mutally exclusive.
Also changed MLX5_INFINIBAND to be depandant on MLX5_CORE instead of
selecting it, since MLX5_CORE could be selected without MLX5_INFINIBAND
being selected.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the resource handling files:
- flow_table.c: This file contains the code to handle the low level API
to configure hardware flow table. It is separated from
the flow_table_en.c, because it will be used in the
future by Raw Ethernet QP in mlx5_ib too.
- en_flow_table.[ch]: Ethernet flow steering handling. The flow table
object contain a mapping between flow specs and TIRs.
This mechanism will be used also to configure e-switch
in the future, when SR-IOV support will be added.
- transobj.[ch] - Low level functions to create/modify/destroy the
transport objects: RQ/SQ/TIR/TIS
- vport.[ch] - Handle attributes of a virtual port (vPort) in the
embedded switch. Currently this switch is a passthrough, until SR-IOV
support will be added.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce set/Query low level functions to access MTU in hardware. To be
used by the netdev.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mlx5_core_modify_cq_moderation() to be used by the netdev, to
set hardware coalescing.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemet get/set port status low level functions to be exposed by the
netdev.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those registers will be used by the ethtool to set/get settings.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Query all supported types of dev caps on driver load.
- Store the Cap data outbox per cap type into driver private data.
- Introduce new Macros to access/dump stored caps (using the auto
generated data types).
- Obsolete SW representation of dev caps (no need for SW copy for each
cap).
- Modify IB driver to use new macros for checking caps.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
