On some Intel BXT platform, wake-up from suspend-to-idle on pressing
power-button is not working. Its noticed that gpio-keys driver marking the
second level IRQ/power-button as wake capable but Intel pintctrl
driver is missing to mark GPIO chip/controller IRQ which first level IRQ
as wake cable if its GPIO pin IRQ is wakeble. So, though the first level
IRQ gets generated on power-button press, since it is not marked as
wake capable resume/wake-up flow is not happening.
Intel pintctrl/GPIO driver need to mark GPIO chip/controller IRQ (first
level IRQ) as wake capable iff GPIO pin's IRQ (second level IRQ) is marked
as wake cable.
Changes in v2:
- Add missing irq initialisation.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies the error handling and allows us to drop the whole
chv_pinctrl_remove() function.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out that for north and southwest communities, they can only
generate GPIO interrupts for lower 8 interrupts (IntSel value). The upper
part (8-15) can only generate GPEs (General Purpose Events).
Now the reason why EC events such as pressing hotkeys does not work if we
mask all the interrupts is that in order to generate either interrupts or
GPEs the INTMASK register must have that particular interrupt unmasked. In
case of GPEs the CPU does not trigger normal interrupt (and thus the GPIO
driver does not see it) but instead it causes SCI (System Control
Interrupt) to be triggered with the GPE in question set.
To make this all work as expected we only add those GPIOs to the IRQ domain
that can actually generate interrupts (IntSel value 0-7) and skip others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.
To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.
Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no point in adding any default trigger for these
GPIO interrupts: the device tree should contain all trigger
information and the platforms using the driver boots
exclusively from device tree.
Also the boot log is nagging me to fix this:
[ 0.771057] ------------[ cut here ]------------
[ 0.775695] WARNING: CPU: 0 PID: 1 at
../drivers/gpio/gpiolib.c:1622 _gpiochip_irqchip_add+0x138/0x160
[ 0.785034] /soc/gpio@8012e000: Ignoring 2 default trigger
(...)
[ 0.942962] gpio 8012e000.gpio: at address e08f8000
(etc ad nauseam)
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl dt doc and removes
references to these obsolete platforms. It also updates
the dt example to the currently supported STiH407
platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linus.walleij@linaro.org>
Cc: <robh+dt@kernel.org>
Cc: <linux-gpio@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl driver and removes
references to these obsolete platforms. As some structures
referenced by STiH407 based configuration were shared with
STiH416 we update these names to match the remaining
supported platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linus.walleij@linaro.org>
Cc: <linux-gpio@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domains pins for the NAND flash controller.
Even tough we have no driver for the NAND flash controller yet, we need
to have these pins in pinctrl as the actual pin are shared with the spifc
controller. The bootloader on the S905-P200 setup pinmux for the NAND
controller so we need the kernel to properly deactivate this if necessary.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added irqchip support for the stm32 pinctrl driver uses
hierarchical IRQ domains as provided by the NVIC primary irqchip.
This works great for any configuration that may be relevant on
stm32, but when doing compile-testing (randconfig), we can
enable it without NVIC or any other primary irqchip that
enables IRQ_DOMAIN_HIERARCHY:
drivers/pinctrl/stm32/pinctrl-stm32.c:212:13: error: 'irq_chip_eoi_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:213:20: error: 'irq_chip_mask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:214:20: error: 'irq_chip_unmask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:215:20: error: 'irq_chip_set_type_parent' undeclared here (not in a function)
This adds a Kconfig dependency to limit compile-testing to
configurations that have IRQ_DOMAIN_HIERARCHY already enabled.
It's not obvious whether we should use 'depends on' or 'select'
here, I think either one works, with 'depends on' being more
intuitive, while 'select' would be less likely to cause dependency
loops.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0eb9f68333 ("pinctrl: Add IRQ support to STM32 gpios")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Return pinconf with arguments in packed format,
- MSIOF and QSPI pin groups on R-Car V2H,
- Voltage switching for SDHI on R-Car M2-W, E2, and M3-W.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=APGj
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.9-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.9 (take three)
- Return pinconf with arguments in packed format,
- MSIOF and QSPI pin groups on R-Car V2H,
- Voltage switching for SDHI on R-Car M2-W, E2, and M3-W.
All the SHDIs can operate with either 3.3V or 1.8V signals, depending
on negotiation with the card.
Based on work by Wolfram Sang for the r8a7790.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All the SHDIs can operate with either 3.3V or 1.8V signals, depending
on negotiation with the card.
Based on work by Wolfram Sang for the r8a7790.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This follows the style of existing PORT_GP_X macros and
will be used by a follow-up patch for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
strict pin controller returns -EINVAL in case of pin request which
is already claimed by somebody else.
Following is the sequence of calling pin_request() from
pinctrl_bind_pins():-
pinctrl_bind_pins()->pinctrl_select_state()->pinmux_enable_setting()->
pin_request()
But pinctrl_bind_pins() only returns -EPROBE_DEFER which makes device
driver probe successful even if the pin request is rejected by the pin
controller subsystem.
This commit modifies pinctrl_bind_pins() to return error if the pin is
rejected by pin control subsystem.
Signed-off-by: Deepak Das <deepak_das@mentor.com>
[Rewrote to be cleaner]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the SDIO interrupt pin which can be used by sd_emmc_a.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: 29885a6565 ("pinctrl: meson-gxbb: add the pins for the
SDIO/sd_emmc_a controller")
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added aspeed driver tries to check for a negative return
value from a pinctrl function, but stores the intermediate value in
a 'bool' variable, which cannot work:
drivers/pinctrl/aspeed/pinctrl-aspeed.c: In function 'aspeed_sig_expr_set':
drivers/pinctrl/aspeed/pinctrl-aspeed.c:192:11: error: comparison of constant '0' with boolean expression is always false [-Werror=bool-compare]
This slightly reworks the logic to use an explicit comparison with zero
before assigning to the temporary variable.
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The earlier patch can be simplified by using a bool
to indicate level trigger.
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
[Fixup to earlier manually applied patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds IRQ support to STM32 gpios.
The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
samsung_pinctrl_probe() can be called only after matching
the driver by the compatible string so this already implies
a non null dev->of_node. Remove the always false test
and related error trace. While at it drop another error log
in case of memory allocation failure - any errors are logged
by the memory subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In function mrfld_pinctrl_probe(), when duplicating the mrfld_families
array the requested memory region length is multiplied once too many by the
number of elements in the original array. Fix this to spare some memory.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a GPIO controller description in board DTB contains information
about mappings between GPIOs and pads under IOMUX control use it to
request and free GPIOs with respect to pinctrl/pinmux subsystems.
One of immediate positive functional changes is inability to
request non-existing GPIOs, i.e. if there is no pad such. Also
pinctrl/pinmux may now properly account pads occupied by requested
GPIOs.
The change has no effect, if "gpio-ranges" property is not found
including the case if a board has no DTB firmware.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In general situation on-SoC GPIO controller drivers should be probed
after pinctrl/pinmux controller driver, because on-SoC GPIOs utilize a
pin/pad as a resource provided and controlled by pinctrl subsystem.
This is stated in multiple places, e.g. from drivers/Makefile:
GPIO must come after pinctrl as gpios may need to mux pins etc
Looking at Freescale iMX SoC series specifics, imx*_pinctrl_init()
functions are called at arch_initcall and postcore_initcall init
levels, so the change of initcall level for gpio-mxc driver from
postcore_initcall to subsys_initcall level is sufficient. Also note
that the most of GPIO controller drivers settled at subsys_initcall
level.
If pinctrl subsystem manages pads with GPIO functions, the change is
needed to avoid unwanted driver probe deferrals during kernel boot.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While only Freescale Vybrid SoC has settings of GPIO capabilities done
by iomux controller, it is only a matter of GPIO controller driver
implementation for the rest of Freescale/NXP SoCs from iMX series.
As a practical example on GPIO request a pad function should be
switched to GPIO, but because this requires updates to all particular
iMX pinctrl drivers, for simplicity at the moment add only a proper
connection between shared pinctrl-imx and pinctrl/pinmux core, namely
.gpio_request_enable/.gpio_disable_free/.gpio_set_direction callbacks
should return success to a caller. This change allows to progress by
adding request/free callbacks into gpio-mxc.c driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
at91 used to set a default trigger type for GPIO interrupts in
order to cope with the old board files. These days are long gone,
and it all gets probed through DT.
Andras Szemzo reported that the Ethernet device on his board was
bailing to be probed, due to a conflict in interrupt trigger.
Surely enough, this is due to this default trigger still being
present, and turning this into a IRQ_TYPE_NONE fixes the issue.
Reported-by: Andras Szemzo <szemzo.andras@gmail.com>
Tested-by: Andras Szemzo <szemzo.andras@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports the {get,set}_io_voltage operations of SDHI.
This operates the POCCTRL0 register on R8A7796 SoC and makes 1.8v/3.3v
voltage switch.
Based on work by Takeshi Kihara and Wolfram Sang.
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinconf-generic code expects configurations with arguments to be
returned in a packed format in order to be displayed properly by
pinconf_generic_dump_one().
Reading /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins on
r8a7795/salvator-x now shows:
pin 101 (GP_3_5): output drive strength (9 mA), pin power source (3300 selector)
Instead of:
pin 101 (GP_3_5): output drive strength (0 mA), pin power source (0 selector)
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add MSIOF0/1 pin groups to the R8A7792 PFC driver.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add QSPI pin groups to the R8A7792 PFC driver.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Commit aa71987472 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).
Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jay Freyensee <james_p_freyensee@linux.intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are a few small IIO fixes for 4.8-rc6.
Nothing major, full details are in the shortlog, all of these have been
in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfVHiQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspQ4YAoJEd
rJOXb3451Zq6KdCgO/1AQUMRAJ9M3umVQA6h5u403ih2NyadrNVDZg==
=Fr22
-----END PGP SIGNATURE-----
Merge tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are a few small IIO fixes for 4.8-rc6.
Nothing major, full details are in the shortlog, all of these have
been in linux-next with no reported issues"
* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:core: fix IIO_VAL_FRACTIONAL sign handling
iio: ensure ret is initialized to zero before entering do loop
iio: accel: kxsd9: Fix scaling bug
iio: accel: bmc150: reset chip at init time
iio: fix pressure data output unit in hid-sensor-attributes
tools:iio:iio_generic_buffer: fix trigger-less mode
Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.
All of these resolve minor issues that have been reported, and all have
been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfVHp0PHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspNBAAoKm1
O+zfSBYR3OWH1Hr3xGgwgxpqAJ92PKIQRP4te/inFvTWb73heYahag==
=DUkg
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.
All of these resolve minor issues that have been reported, and all
have been in linux-next with no reported issues"
* tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
xhci: fix null pointer dereference in stop command timeout function
usb: dwc3: pci: fix build warning on !PM_SLEEP
usb: gadget: prevent potenial null pointer dereference on skb->len
usb: renesas_usbhs: fix clearing the {BRDY,BEMP}STS condition
usb: phy: phy-generic: Check clk_prepare_enable() error
usb: gadget: udc: renesas-usb3: clear VBOUT bit in DRD_CON
Revert "usb: dwc3: gadget: always decrement by 1"
Pull libnvdimm fixes from Dan Williams:
"nvdimm fixes for v4.8, two of them are tagged for -stable:
- Fix devm_memremap_pages() to use track_pfn_insert(). Otherwise,
DAX pmd mappings end up with an uncached pgprot, and unusable
performance for the device-dax interface. The device-dax interface
appeared in 4.7 so this is tagged for -stable.
- Fix a couple VM_BUG_ON() checks in the show_smaps() path to
understand DAX pmd entries. This fix is tagged for -stable.
- Fix a mis-merge of the nfit machine-check handler to flip the
polarity of an if() to match the final version of the patch that
Vishal sent for 4.8-rc1. Without this the nfit machine check
handler never detects / inserts new 'badblocks' entries which
applications use to identify lost portions of files.
- For test purposes, fix the nvdimm_clear_poison() path to operate on
legacy / simulated nvdimm memory ranges. Without this fix a test
can set badblocks, but never clear them on these ranges.
- Fix the range checking done by dax_dev_pmd_fault(). This is not
tagged for -stable since this problem is mitigated by specifying
aligned resources at device-dax setup time.
These patches have appeared in a next release over the past week. The
recent rebase you can see in the timestamps was to drop an invalid fix
as identified by the updated device-dax unit tests [1]. The -mm
touches have an ack from Andrew"
[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: allow legacy (e820) pmem region to clear bad blocks
nfit, mce: Fix SPA matching logic in MCE handler
mm: fix cache mode of dax pmd mappings
mm: fix show_smap() for zone_device-pmd ranges
dax: fix mapping size check
Pull i2c fixes from Wolfram Sang:
"Mostly driver bugfixes, but also a few cleanups which are nice to have
out of the way"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Restore clock settings at resume time
i2c: Spelling s/acknowedge/acknowledge/
i2c: designware: save the preset value of DW_IC_SDA_HOLD
Documentation: i2c: slave-interface: add note for driver development
i2c: mux: demux-pinctrl: run properly with multiple instances
i2c: bcm-kona: fix inconsistent indenting
i2c: rcar: use proper device with dma_mapping_error
i2c: sh_mobile: use proper device with dma_mapping_error
i2c: mux: demux-pinctrl: invalidate properly when switching fails
allows a malicious user to set an encryption policy on an empty
directory which they do not own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJX05q4AAoJEPL5WVaVDYGjOywH/AyXoo4d1/5H/XTakNYPxYIW
vtBOXciHai4ZE9RygL3gdZuiyY9bTx2sc80So3KboNUdiuOJBPnuAkOQMr973UCI
yGW3eP/RYGA1XQUbtOyFvzJMIZLKXV2ytakFeRz+m1CQF2F5F7/prKQB2j4sWHff
JigAC67LlZSiz7L8SqtPG4uG1C8K/YEorf14dG6k37fMwE/AaBYXxkyc7MmHIKeW
Tils0ZZcTK0U0udNSel/jRSS/qENEuLvKhFsMAlIDrCETVMidCvv2OAcT0z0z5Ln
v+Oq0Xfutd12nfb95LUfROMtTzrtILYC2qNfDChOoFtlU8UyKmY+WT1GfYUiy8g=
=ahmA
-----END PGP SIGNATURE-----
Merge tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull fscrypto fixes fromTed Ts'o:
"Fix some brown-paper-bag bugs for fscrypto, including one one which
allows a malicious user to set an encryption policy on an empty
directory which they do not own"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fscrypto: require write access to mount to set encryption policy
fscrypto: only allow setting encryption policy on directories
fscrypto: add authorization check for setting encryption policy
Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem. This was handled correctly by f2fs but not by ext4. Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files. This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.
In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.
This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later. It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.
This patch restores the !S_ISDIR() check that was present in older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access. This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).
Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy. This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.
(*) Or also on any regular file, for f2fs v4.6 and later and ext4
v4.8-rc1 and later; a separate bug fix is coming for that.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.
Fixes: 6839a6d nfit: do an ARS scrub on hitting a latent media error
Cc: linux-acpi@vger.kernel.org
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage. DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).
track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range. While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not. So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.
Cc: <stable@vger.kernel.org>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Kai Zhang <kai.ka.zhang@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
