The interface to configure the LIF in the VSP1 requires adapting the
function prototype for any changes. This makes extending the interface
difficult.
Change the function prototype to pass a structure which can be easily
extended.
This changes the means of disabling the pipeline, by now passing a NULL
configuration rather than passing either a 0 width or height.
[Fixed kerneldoc, made vsp1_du_setup_lif() cfg argument const]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Kernel 4.9, WARNINGs about doing DMA on stack are hit at
the dw2102 driver: one in su3000_power_ctrl() and the other in tt_s2_4600_frontend_attach().
Both were due to the use of buffers on the stack as parameters to
dvb_usb_generic_rw() and the resulting attempt to do DMA with them.
The device was non-functional as a result.
So, switch this driver over to use a buffer within the device state
structure, as has been done with other DVB-USB drivers.
Tested with TechnoTrend TT-connect S2-4600.
[mchehab@osg.samsung.com: fixed a warning at su3000_i2c_transfer() that
state var were dereferenced before check 'd']
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ir_raw_event_register() sets up change_protocol(), and without that set,
rc_setup_rx_device() does not set the protocol for the device on register.
The standard udev rules run ir-keytable, which writes to the protocols
file again, which hides this problem.
Fixes: 7ff2c2b ("[media] rc-main: split setup and unregister functions")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the protocol is set via the sysfs protocols attribute, the
decoder is loaded. However, when it is not when a device is first
plugged in or registered.
Fixes: acc1c3c ("[media] media: rc: load decoder modules on-demand")
Signed-off-by: Sean Young <sean@mess.org>
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the interrupt requested with devm_request_irq(), serial_ir.rcdev
is still null so will cause null deference if the irq handler is called
early on.
Also ensure that timeout_timer is setup.
Link: http://lkml.kernel.org/r/CA+55aFxsh2uF8gi5sN_guY3Z+tiLv7LpJYKBw+y8vqLzp+TsnQ@mail.gmail.com
[mchehab@s-opensource.com: moved serial_ir_probe() back to its original place]
Cc: <stable@vger.kernel.org> # 4.10
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After removing DEBUG from mtk_vcodec_util.h, some build warnings are
generated as the following:
.../drivers/media/platform/mtk-vcodec/vdec_vpu_if.c: In function 'vcodec_vpu_send_msg':
.../drivers/media/platform/mtk-vcodec/vdec_vpu_if.c:73:11: warning: unused variable 'msg_id' [-Wunused-variable]
uint32_t msg_id = *(uint32_t *)msg;
^
.../drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c: In function 'vb2ops_vdec_buf_queue':
.../drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:1129:7: warning: unused variable 'log_level' [-Wunused-variable]
int log_level = ret ? 0 : 1;
^
.../drivers/media/platform/mtk-vcodec/venc_vpu_if.c: In function 'vpu_enc_send_msg':
.../drivers/media/platform/mtk-vcodec/venc_vpu_if.c:82:12: warning: unused variable 'msg_id' [-Wunused-variable]
uint32_t msg_id = *(uint32_t *)msg;
^
It is because mtk_vcodec_debug() and mtk_vcodec_err() are defined as empty
macros. Without DEBUG definition, the variable for debugging is not used
anymore. Fixing build warnings by moving the assignment of the
variable to the argument of mtk_vcodec_debug() and mtk_vcodec_err().
Within the patch, build pass with/without DEBUG definition, and functions
still work fine.
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the USB driver is enabled but the demodulator is not, we get a link error:
ERROR: "zd1301_demod_get_dvb_frontend" [drivers/media/usb/dvb-usb-v2/zd1301.ko] undefined!
ERROR: "zd1301_demod_get_i2c_adapter" [drivers/media/usb/dvb-usb-v2/zd1301.ko] undefined!
Such a configuration obviously makes no sense, but we should not fail
the build. This tries to mimic what we have for other drivers by turning
the build failure into a runtime failure.
Alternatively we could use an unconditional 'select' or 'depends on' to enforce
a sane configuration.
Fixes: 47d65372b3 ("[media] zd1301_demod: ZyDAS ZD1301 DVB-T demodulator driver")
Fixes: 992b39872b ("[media] zd1301: ZyDAS ZD1301 DVB USB interface driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 17ce039b4e ("[media] cxusb: don't do DMA on stack")
added a kmalloc'ed bounce buffer for writes, but missed to do the same
for reads. As the read only happens after the write is finished, we can
reuse the same buffer.
As dvb_usb_generic_rw handles a read length of 0 by itself, avoid calling
it using the dvb_usb_generic_read wrapper function.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-7.0.1 warns about old code in ttpci:
In file included from drivers/media/pci/ttpci/av7110.c:63:0:
In function 'irdebi.isra.2',
inlined from 'start_debi_dma' at drivers/media/pci/ttpci/av7110.c:376:3,
inlined from 'gpioirq' at drivers/media/pci/ttpci/av7110.c:659:3:
drivers/media/pci/ttpci/av7110_hw.h:406:3: warning: 'memcpy': specified size between 18446744071562067968 and 18446744073709551615 exceeds maximum object size 9223372036854775807 [-Wstringop-overflow=]
memcpy(av7110->debi_virt, (char *) &res, count);
In function 'irdebi.isra.2',
inlined from 'start_debi_dma' at drivers/media/pci/ttpci/av7110.c:376:3,
inlined from 'gpioirq' at drivers/media/pci/ttpci/av7110.c:668:3:
drivers/media/pci/ttpci/av7110_hw.h:406:3: warning: 'memcpy': specified size between 18446744071562067968 and 18446744073709551615 exceeds maximum object size 9223372036854775807 [-Wstringop-overflow=]
memcpy(av7110->debi_virt, (char *) &res, count);
Apparently, 'count' can be negative here, which will then get turned
into a giant size argument for memcpy. Changing the sizes to 'unsigned
int' instead seems safe as we already check for maximum sizes, and it
also simplifies the code a bit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I ran into a stack frame size warning because of the on-stack copy of
the USB device structure:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_disconnect':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:1029:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Copying a device structure like this is wrong for a number of other reasons
too aside from the possible stack overflow. One of them is that the
dev_info() call will print the name of the device later, but AFAICT
we have only copied a pointer to the name earlier and the actual name
has been freed by the time it gets printed.
This removes the on-stack copy of the device and instead copies the
device name using kstrdup(). I'm ignoring the possible failure here
as both printk() and kfree() are able to deal with NULL pointers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adding Hama Hybrid DVB-T Stick support. Technically it's the same
device what Terratec Cinergy HT USB XE is.
Signed-off-by: Piotr Oleszczyk <piotr.oleszczyk@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a compiler warning due to an unused but assigned variable.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add simple 'functionality' member to dummy Exynos IS i2c adapter to make
i2c core happy and get rid of NULL pointer dereference during Exynos4 IS
probe since v4.10-rc1:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000005 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 100 Comm: kworker/1:2 Not tainted 4.10.0-rc6-next-20170131-00054-g39e6e4233de6 #1921
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
task: ef2e0000 task.stack: ef2ec000
PC is at 0x0
LR is at i2c_register_adapter+0x98/0x5cc
...
[<c05040bc>] (i2c_register_adapter) from [<c05379d4>] (fimc_is_i2c_probe+0x84/0xe4)
[<c05379d4>] (fimc_is_i2c_probe) from [<c041b5c8>] (platform_drv_probe+0x50/0xb0)
[<c041b5c8>] (platform_drv_probe) from [<c0419f48>] (driver_probe_device+0x234/0x2dc)
[<c0419f48>] (driver_probe_device) from [<c04184e0>] (bus_for_each_drv+0x44/0x8c)
[<c04184e0>] (bus_for_each_drv) from [<c0419c8c>] (__device_attach+0x9c/0x100)
[<c0419c8c>] (__device_attach) from [<c0419374>] (bus_probe_device+0x84/0x8c)
[<c0419374>] (bus_probe_device) from [<c04178d4>] (device_add+0x380/0x528)
[<c04178d4>] (device_add) from [<c05aceb4>] (of_platform_device_create_pdata+0x70/0xa4)
[<c05aceb4>] (of_platform_device_create_pdata) from [<c05acfd4>] (of_platform_bus_create+0xec/0x320)
[<c05acfd4>] (of_platform_bus_create) from [<c05ad264>] (of_platform_populate+0x5c/0xac)
[<c05ad264>] (of_platform_populate) from [<c0533420>] (fimc_is_probe+0x1c0/0x4cc)
[<c0533420>] (fimc_is_probe) from [<c041b5c8>] (platform_drv_probe+0x50/0xb0)
[<c041b5c8>] (platform_drv_probe) from [<c0419f48>] (driver_probe_device+0x234/0x2dc)
[<c0419f48>] (driver_probe_device) from [<c04184e0>] (bus_for_each_drv+0x44/0x8c)
[<c04184e0>] (bus_for_each_drv) from [<c0419c8c>] (__device_attach+0x9c/0x100)
[<c0419c8c>] (__device_attach) from [<c0419374>] (bus_probe_device+0x84/0x8c)
[<c0419374>] (bus_probe_device) from [<c04197a8>] (deferred_probe_work_func+0x60/0x8c)
[<c04197a8>] (deferred_probe_work_func) from [<c01329a4>] (process_one_work+0x120/0x31c)
[<c01329a4>] (process_one_work) from [<c0132bc8>] (process_scheduled_works+0x28/0x38)
[<c0132bc8>] (process_scheduled_works) from [<c0132ddc>] (worker_thread+0x204/0x4ac)
[<c0132ddc>] (worker_thread) from [<c01381b8>] (kthread+0xfc/0x134)
[<c01381b8>] (kthread) from [<c01078b8>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All lanes in data-lanes and clock-lanes properties should be unique. Add
a check for this in v4l2_of_parse_csi_bus() and print a warning if
duplicated lanes are found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds some trace points showing input compressed stream or
output decoded frame information.
Adds an unconditional trace point when streaming starts showing
the compressed stream and the decoded frame information.
Adds an unconditional trace point at instance closure summarizing
into a single line the decoding process (stream information, decoded
and output frames number, potential errors observed).
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds support of DELTA MJPEG video decoder back-end,
implemented by calling JPEG_DECODER_HW0 firmware
using RPMSG IPC communication layer.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
EOS (End Of Stream) support allows user to get
all the potential decoded frames remaining in decoder
pipeline after having reached the end of video bitstream.
To do so, user calls VIDIOC_DECODER_CMD(V4L2_DEC_CMD_STOP)
which will drain the decoder and get the drained frames
that are then returned to user.
User is informed of EOS completion in two ways:
- dequeue of an empty frame flagged to V4L2_BUF_FLAG_LAST
- reception of a V4L2_EVENT_EOS event.
If, unfortunately, no buffer is available on CAPTURE queue
to return the empty frame, EOS is delayed till user queue
one CAPTURE buffer.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
IPC (Inter Process Communication) support for communication with
DELTA coprocessor firmware using rpmsg kernel framework.
Based on 4 services open/set_stream/decode/close and their associated
rpmsg messages.
The messages structures are duplicated on both host and firmware
side and are packed (use only of 32 bits size fields in messages
structures to ensure packing).
Each service is synchronous; service returns only when firmware
acknowledges the associated command message.
Due to significant parameters size exchanged from host to copro,
parameters are not inserted in rpmsg messages. Instead, parameters are
stored in physical memory shared between host and coprocessor.
Memory is non-cacheable, so no special operation is required
to ensure memory coherency on host and on coprocessor side.
Multi-instance support and re-entrance are ensured using host_hdl and
copro_hdl in message header exchanged between both host and coprocessor.
This avoids to manage tables on both sides to get back the running context
of each instance.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Helper functions used by decoder back-ends to allocate
physically contiguous memory required by hardware video
decoder.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal Master 3 Bus can send and receive only 4 bytes per time.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch provide only digital support.
The device is based on Si2168 30-demodulator,
Si2158-20 tuner and CX23102-11Z chipset;
USB id: 1b80:d3b2.
Status:
- DVB-T2 works fine;
- Composite and SVideo works fine;
- Analog not implemented.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2-async had several functions doing some operations and then
not undoing the operations in a failure situation. For example,
v4l2_async_test_notify() moved a subdev into notifier's done list
even if registering the subdev (v4l2_device_register_subdev) failed.
If the subdev was allocated and v4l2_async_register_subdev() called
from the driver's probe() function, as usually, the probe()
function freed the allocated subdev and returned a failure.
Nevertheless, the subdev was still left into the notifier's done
list, causing an access to already freed memory when the notifier
was later unregistered.
A hand-edited call trace leaving freed subdevs into the notifier:
v4l2_async_register_notifier(notifier, asd)
cameradrv_probe
sd = devm_kzalloc()
v4l2_async_register_subdev(sd)
v4l2_async_test_notify(notifier, sd, asd)
list_move(sd, ¬ifier->done)
v4l2_device_register_subdev(notifier->v4l2_dev, sd)
cameradrv_registered(sd) -> fails
->v4l2_async_register_subdev returns failure
->cameradrv_probe returns failure
->devres frees the allocated sd
->sd was freed but it still remains in the notifier's list.
This patch fixes this and several other cases where a failing
function could leave nodes into a linked list while the caller
might free the node due to a failure.
Signed-off-by: Tuukka Toivonen <tuukka.toivonen@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We should be returning negative error codes here or it leads to a crash.
This also silences a static checker warning.
drivers/media/pci/mantis/mantis_cards.c:250 mantis_pci_probe()
warn: 'mantis->dmxdev.dvbdev->fops' double freed
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There isn't an ioctl to enum the supported field orders, so a user-space
application can call VIDIOC_TRY_FMT using different field orders to know
if one is supported. For example, GStreamer does this so during playback
dozens of the following messages appear in the kernel log buffer:
[ 442.143393] Not supported field order(4)
Instead of printing this as an error, just keep it as debug information.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is likely that a "of_node_put(ep)" is missing here.
There is one in the previous error handling code, and one a few lines
below in the normal case as well.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare vb2_ops structure as const as it is only stored in
the ops field of a vb2_queue structure. This field is of type
const, so vb2_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct sta2x11_vip vip;
struct vb2_queue q;
@@
(
vip.vb_vidq.ops=&i@p
|
q.ops=&i@p
)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct vb2_ops i;
File size details of media/dvb-frontends/rtl2832_sdr.o file remains the
same before and after applying the patch.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare vb2_ops structure as const as it is only stored in
the ops field of a vb2_queue structure. This field is of type
const, so vb2_ops structures having same properties can be made
const too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct sta2x11_vip vip;
struct vb2_queue q;
@@
(
vip.vb_vidq.ops=&i@p
|
q.ops=&i@p
)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct vb2_ops i;
File size before:
text data bss dec hex filename
8448 440 0 8888 22b8 media/pci/sta2x11/sta2x11_vip.o
File size after:
text data bss dec hex filename
8552 352 0 8904 22c8 media/pci/sta2x11/sta2x11_vip.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the subdev devnode pointer right after registration to ensure that
later errors won't skip the subdev when unregistering all devnodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Freescale provided imx-vpu looks for firmware files under /lib/firmware/vpu
by default. Make coda look there for firmware files to ease the update path.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The UK layout of the Microsoft Remote Keyboard has two missing keys:
the hash key, and the messenger key which is sent using rc6 mce.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bail out early, otherwise we follow a null pointer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Keep the list up to date with include/media/rc-map.h
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver already parses the "linux,rc-map-name" property. Add this
information to the documentation so .dts maintainers don't have to look
it up in the source-code.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes the following sparse warning:
drivers/media/usb/dvb-usb/gp8psk.c:281:28: warning:
symbol 'gp8psk_fe_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge WinTV-dualHD model 01595 is a USB 2.0 dual ATSC/QAM tuner with
the following components:
USB bridge: Empia em28274
Demodulator: 2x LG LGDT3306a at addresses 0xb2 and 0x1c
Tuner: 2x Silicon Labs si2157 at addresses 0xc0 and 0xc4
This patch enables only the first tuner.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds an i2c mux to the lgdt3306a demodulator. This was done to support
the Hauppauge WinTV-dualHD 01595 USB TV tuner (em28xx), which utilizes two
si2157 tuners behind gate control.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While the wakeup path seems to be set up, this waitqueue is actually
never used as no-one enqueues themselves on the list. As such, wakeups
are meaningless without waiters, so lets just get rid of the whole
thing.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
