Prior to
commit d021fabf52 ("rds: rdma: add consumer reject")
function "rds_rdma_cm_event_handler_cmn" would always honor a rejected
connection attempt by issuing a "rds_conn_drop".
The commit mentioned above added a "break", eliminating
the "fallthrough" case and made the "rds_conn_drop" rather conditional:
Now it only happens if a "consumer defined" reject (i.e. "rdma_reject")
carries an integer-value of "1" inside "private_data":
if (!conn)
break;
err = (int *)rdma_consumer_reject_data(cm_id, event, &len);
if (!err || (err && ((*err) == RDS_RDMA_REJ_INCOMPAT))) {
pr_warn("RDS/RDMA: conn <%pI6c, %pI6c> rejected, dropping connection\n",
&conn->c_laddr, &conn->c_faddr);
conn->c_proposed_version = RDS_PROTOCOL_COMPAT_VERSION;
rds_conn_drop(conn);
}
rdsdebug("Connection rejected: %s\n",
rdma_reject_msg(cm_id, event->status));
break;
/* FALLTHROUGH */
A number of issues are worth mentioning here:
#1) Previous versions of the RDS code simply rejected a connection
by calling "rdma_reject(cm_id, NULL, 0);"
So the value of the payload in "private_data" will not be "1",
but "0".
#2) Now the code has become dependent on host byte order and sizing.
If one peer is big-endian, the other is little-endian,
or there's a difference in sizeof(int) (e.g. ILP64 vs LP64),
the *err check does not work as intended.
#3) There is no check for "len" to see if the data behind *err is even valid.
Luckily, it appears that the "rdma_reject(cm_id, NULL, 0)" will always
carry 148 bytes of zeroized payload.
But that should probably not be relied upon here.
#4) With the added "break;",
we might as well drop the misleading "/* FALLTHROUGH */" comment.
This commit does _not_ address issue #2, as the sender would have to
agree on a byte order as well.
Here is the sequence of messages in this observed error-scenario:
Host-A is pre-QoS changes (excluding the commit mentioned above)
Host-B is post-QoS changes (including the commit mentioned above)
#1 Host-B
issues a connection request via function "rds_conn_path_transition"
connection state transitions to "RDS_CONN_CONNECTING"
#2 Host-A
rejects the incompatible connection request (from #1)
It does so by calling "rdma_reject(cm_id, NULL, 0);"
#3 Host-B
receives an "RDMA_CM_EVENT_REJECTED" event (from #2)
But since the code is changed in the way described above,
it won't drop the connection here, simply because "*err == 0".
#4 Host-A
issues a connection request
#5 Host-B
receives an "RDMA_CM_EVENT_CONNECT_REQUEST" event
and ends up calling "rds_ib_cm_handle_connect".
But since the state is already in "RDS_CONN_CONNECTING"
(as of #1) it will end up issuing a "rdma_reject" without
dropping the connection:
if (rds_conn_state(conn) == RDS_CONN_CONNECTING) {
/* Wait and see - our connect may still be succeeding */
rds_ib_stats_inc(s_ib_connect_raced);
}
goto out;
#6 Host-A
receives an "RDMA_CM_EVENT_REJECTED" event (from #5),
drops the connection and tries again (goto #4) until it gives up.
Tested-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
This reverts commit 5601245931.
RDS kept spinning inside function "rds_ib_post_reg_frmr", waiting for
"i_fastreg_wrs" to become incremented:
while (atomic_dec_return(&ibmr->ic->i_fastreg_wrs) <= 0) {
atomic_inc(&ibmr->ic->i_fastreg_wrs);
cpu_relax();
}
Looking at the original commit:
commit 5601245931 ("RDS: IB: split the mr registration and
invalidation path")
In there, the "rds_ib_mr_cqe_handler" was changed in the following
way:
void rds_ib_mr_cqe_handler(struct
rds_ib_connection *ic,
struct ib_wc *wc)
if (frmr->fr_inv) {
frmr->fr_state = FRMR_IS_FREE;
frmr->fr_inv = false;
atomic_inc(&ic->i_fastreg_wrs);
} else {
atomic_inc(&ic->i_fastunreg_wrs);
}
It looks like it's got it exactly backwards:
Function "rds_ib_post_reg_frmr" keeps track of the outstanding
requests via "i_fastreg_wrs".
Function "rds_ib_post_inv" keeps track of the outstanding requests
via "i_fastunreg_wrs" (post original commit). It also sets:
frmr->fr_inv = true;
However the completion handler "rds_ib_mr_cqe_handler" adjusts
"i_fastreg_wrs" when "fr_inv" had been true, and adjusts
"i_fastunreg_wrs" otherwise.
The original commit was done in the name of performance:
to remove the performance bottleneck
No performance benefit could be observed with a fixed-up version
of the original commit measured between two Oracle X7 servers,
both equipped with Mellanox Connect-X5 HCAs.
The prudent course of action is to revert this commit.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
RDS composite message(rdma + control) user notification needs to be
triggered once the full message is delivered and such a fix was
added as part of commit 941f8d55f6 ("RDS: RDMA: Fix the composite
message user notification"). But rds_send_remove_from_sock is missing
data part notify check and hence at times the user don't get
notification which isn't desirable.
One way is to fix the rds_send_remove_from_sock to check of that case
but considering the ordering complexity with completion handler and
rdma + control messages are always dispatched back to back in same send
context, just delaying the signaled completion on rmda work request also
gets the desired behaviour. i.e Notifying application only after
RDMA + control message send completes. So patch updates the earlier
fix with this approach. The delay signaling completions of rdma op
till the control message send completes fix was done by Venkat
Venkatsubra in downstream kernel.
Reviewed-and-tested-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:251:2:
warning: variable 'rec_seq_sz' is used uninitialized whenever switch
default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:255:46: note:
uninitialized use occurs here
skip_static_post = !memcmp(rec_seq, &rn_be, rec_seq_sz);
^~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:239:16: note:
initialize the variable 'rec_seq_sz' to silence this warning
u16 rec_seq_sz;
^
= 0
1 warning generated.
This case statement was clearly designed to be one that should not be
hit during runtime because of the WARN_ON statement so just return early
to prevent copying uninitialized memory up into rn_be.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Link: https://github.com/ClangBuiltLinux/linux/issues/590
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return value was changes to 'int' from void but this return statement
was not updated, or it slipped in via a merge.
Fixes: b5d9a834f4 ("net/tls: don't clear TX resync flag on error")
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9903c8dc73 changed TC_ETF defines to use _BITUL instead of BIT
but did not add the dependecy on linux/const.h. As a consequence,
importing the uapi headers into iproute2 causes builds to fail. Add
the dependency.
Fixes: 9903c8dc73 ("etf: Don't use BIT() in UAPI headers.")
Cc: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On commit ba2b232108 ("net: netsec: add XDP support") a static
declaration for netsec_set_tx_de() was added to make the diff easier
to read. Now that the patch is merged let's move the functions around
and get rid of that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While freeing tx buffers the memory has to be unmapped if the packet was
an skb or was used for .ndo_xdp_xmit using the same arguments. Get rid
of the unneeded extra 'else if' statement
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter: add hardware offload infrastructure
This patchset adds support for Netfilter hardware offloads.
This patchset reuses the existing block infrastructure, the
netdev_ops->ndo_setup_tc() interface, TC_SETUP_CLSFLOWER classifier and
the flow rule API.
Patch #1 adds flow_block_cb_setup_simple(), most drivers do the same thing
to set up flow blocks, to reduce the number of changes, consolidate
codebase. Use _simple() postfix as requested by Jakub Kicinski.
This new function resides in net/core/flow_offload.c
Patch #2 renames TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND.
Patch #3 renames TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*.
Patch #4 adds flow_block_cb_alloc() and flow_block_cb_free() helper
functions, this is the first patch of the flow block API.
Patch #5 adds the helper to deal with list operations in the flow block API.
This includes flow_block_cb_lookup(), flow_block_cb_add() and
flow_block_cb_remove().
Patch #6 adds flow_block_cb_priv(), flow_block_cb_incref() and
flow_block_cb_decref() which completes the flow block API.
Patch #7 updates the cls_api to use the flow block API from the new
tcf_block_setup(). This infrastructure transports these objects
via list (through the tc_block_offload object) back to the core
for registration.
CLS_API DRIVER
TC_SETUP_BLOCK ----------> setup flow_block_cb object &
it adds object to flow_block_offload->cb_list
|
CLS_API <-----------------------'
registers list with flow blocks
flow_block_cb & travels back to
calls ->reoffload the core for registration
drivers allocate and sets up (configure the blocks), then
registration happens from the core (cls_api and netfilter).
Patch #8 updates drivers to use the flow block API.
Patch #9 removes the tcf block callback API, which is replaced by the
flow block API.
Patch #10 adds the flow_block_cb_is_busy() helper to check if the block
is already used by a subsystem. This helper is invoked from
drivers. Once drivers are updated to support for multiple
subsystems, they can remove this check.
Patch #11 rename tc structure and definitions for the block bind/unbind
path.
Patch #12 introduces basic netfilter hardware offload infrastructure
for the ingress chain. This includes 5-tuple exact matching
and accept / drop rule actions. Only basechains are supported
at this stage, no .reoffload callback is implemented either.
Default policy to "accept" is only supported for now.
table netdev filter {
chain ingress {
type filter hook ingress device eth0 priority 0; flags offload;
ip daddr 192.168.0.10 tcp dport 22 drop
}
}
This patchset reuses the existing tcf block callback API and it places it
in the flow block callback API in net/core/flow_offload.c.
This series aims to address Jakub and Jiri's feedback, please see specific
patches in this batch for changelog in this v4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware offload support for nftables through the
existing netdev_ops->ndo_setup_tc() interface, the TC_SETUP_CLSFLOWER
classifier and the flow rule API. This hardware offload support is
available for the NFPROTO_NETDEV family and the ingress hook.
Each nftables expression has a new ->offload interface, that is used to
populate the flow rule object that is attached to the transaction
object.
There is a new per-table NFT_TABLE_F_HW flag, that is set on to offload
an entire table, including all of its chains.
This patch supports for basic metadata (layer 3 and 4 protocol numbers),
5-tuple payload matching and the accept/drop actions; this also includes
basechain hardware offload only.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds tcf_block_setup() which uses the flow block API.
This infrastructure takes the flow block callbacks coming from the
driver and register/unregister to/from the cls_api core.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completes the flow block API to introduce:
* flow_block_cb_priv() to access callback private data.
* flow_block_cb_incref() to bump reference counter on this flow block.
* flow_block_cb_decref() to decrement the reference counter.
These functions are taken from the existing tcf_block_cb_priv(),
tcf_block_cb_incref() and tcf_block_cb_decref().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the list handling functions for the flow block API:
* flow_block_cb_lookup() allows drivers to look up for existing flow blocks.
* flow_block_cb_add() adds a flow block to the per driver list to be registered
by the core.
* flow_block_cb_remove() to remove a flow block from the list of existing
flow blocks per driver and to request the core to unregister this.
The flow block API also annotates the netns this flow block belongs to.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new helper function to allocate flow_block_cb objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.
This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.
This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.
This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.
There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao says:
====================
net: hisilicon: Add support for HI13X1 to hip04_eth
The main purpose of this patch series is to extend the
hip04_eth driver to support HI13X1_GMAC.
The offset and bitmap of some registers of HI13X1_GMAC
are different from hip04_eth common soc. In addition,
the definition of send descriptor and parsing descriptor
are different from hip04_eth common soc. So the macro
of the register offset is redefined to adapt the HI13X1_GMAC.
Clean up the sparse warning by the way.
Change since v1:
* Add a cover letter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1 changed the offsets and bitmaps for tx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1 changed the offsets and bitmaps for rx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buf unit size of HI13X1_GMAC is cache_line_size,
which is 64, so the address we write to the buf register
needs to be shifted right by 6 bits.
The 31st bit of the PPE_CFG_CPU_ADD_ADDR register
of HI13X1_GMAC indicates whether to release the buffer
of the message, and the low indicates that it is valid.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1_GMAC delete request for soft reset at first,
otherwise, the subsequent initialization will not
take effect.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1_GMAC changed the offsets and bitmaps for
GE_TX_LOCAL_PAGE_REG registers in the same peripheral
device on different models of the hip04_eth. With the
default configuration, HI13X1_GMAC can also work without
any writes to the GE_TX_LOCAL_PAGE_REG register.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning from sparse:
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning from sparse:
hip04_eth.c:468:25: warning: incorrect type in assignment
hip04_eth.c:468:25: expected unsigned int [usertype] send_addr
hip04_eth.c:468:25: got restricted __be32 [usertype]
hip04_eth.c:469:25: warning: incorrect type in assignment
hip04_eth.c:469:25: expected unsigned int [usertype] send_size
hip04_eth.c:469:25: got restricted __be32 [usertype]
hip04_eth.c:470:19: warning: incorrect type in assignment
hip04_eth.c:470:19: expected unsigned int [usertype] cfg
hip04_eth.c:470:19: got restricted __be32 [usertype]
hip04_eth.c:472:23: warning: incorrect type in assignment
hip04_eth.c:472:23: expected unsigned int [usertype] wb_addr
hip04_eth.c:472:23: got restricted __be32 [usertype]
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the hip04_eth driver to support HI13X1_GMAC.
Enable it with CONFIG_HI13X1_GMAC option.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Biao Huang says:
====================
stmmac: fix out-of-boundary issue and add taller hash table support
Fix mac address out-of-boundary issue in net-next tree.
and resend the patch which was discussed in
https://lore.kernel.org/patchwork/patch/1082117
but with no further progress.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1. get hash table size in hw feature reigster, and add support
for taller hash table(128/256) in dwmac4.
2. only clear GMAC_PACKET_FILTER bits used in this function,
to avoid side effect to functions of other bits.
stmmac selftests output log with flow control on:
ethtool -t eth0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters 0
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address array size is GMAC_MAX_PERFECT_ADDRESSES,
so the 'reg' should be less than it, or will affect other registers.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates says:
====================
tc-testing: Add plugin for simple traffic generation
This series supersedes the previous submission that included a patch for test
case verification using JSON output. It adds a new tdc plugin, scapyPlugin, as
a way to send traffic to test tc filters and actions.
The first patch makes a change to the TdcPlugin module that will allow tdc
plugins to examine the test case currently being executed, so plugins can
play a more active role in testing by accepting information or commands from
the test case. This is required for scapyPlugin to work.
The second patch adds scapyPlugin itself, and an example test case file to
demonstrate how the scapy block works in the test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The scapyPlugin allows for simple traffic generation in tdc to
test various tc features. It was tested with scapy v2.4.2, but
should work with any successive version.
In order to use the plugin's functionality, scapy must be
installed. This can be done with:
pip3 install scapy
or to install 2.4.2:
pip3 install scapy==2.4.2
If the plugin is unable to import the scapy module, it will
terminate the tdc run.
The plugin makes use of a new key in the test case data, 'scapy'.
This block contains three other elements: 'iface', 'count', and
'packet':
"scapy": {
"iface": "$DEV0",
"count": 1,
"packet": "Ether(type=0x800)/IP(src='16.61.16.61')/ICMP()"
},
* iface is the name of the device on the host machine from which
the packet(s) will be sent. Values contained within tdc_config.py's
NAMES dict can be used here - this is useful if paired with
nsPlugin
* count is the number of copies of this packet to be sent
* packet is a string detailing the different layers of the packet
to be sent. If a property isn't explicitly set, scapy will set
default values for you.
Layers in the packet info are separated by slashes. For info about
common TCP and IP properties, see:
https://blogs.sans.org/pen-testing/files/2016/04/ScapyCheatSheet_v0.2.pdf
Caution is advised when running tests using the scapy functionality,
since the plugin blindly sends the packet as defined in the test case
data.
See creating-testcases/scapy-example.json for sample test cases;
the first test is intended to pass while the second is intended to
fail.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of only passing the test case name and ID, pass the
entire current test case down to the plugins. This change
allows plugins to start accepting commands and directives
from the test cases themselves, for greater flexibility
in testing.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The restructuring of the driver got the dependencies wrong: without
CONFIG_NET_DSA we get this build failure:
WARNING: unmet direct dependencies detected for NET_DSA_VITESSE_VSC73XX
Depends on [n]: NETDEVICES [=y] && HAVE_NET_DSA [=y] && OF [=y] && NET_DSA [=n]
Selected by [m]:
- NET_DSA_VITESSE_VSC73XX_PLATFORM [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && HAS_IOMEM [=y]
ERROR: "dsa_unregister_switch" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
ERROR: "dsa_switch_alloc" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
ERROR: "dsa_register_switch" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
Add the appropriate dependencies.
Fixes: 95711cd5f0 ("net: dsa: vsc73xx: Split vsc73xx driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josua Mayer says:
====================
Fix hang of Armada 8040 SoC in orion-mdio
With a modular kernel as configured by Debian a hang was observed with
the Armada 8040 SoC in the Clearfog GT and Macchiatobin boards.
The 8040 SoC actually requires four clocks to be enabled for the mdio
interface to function. All 4 clocks are already specified in
armada-cp110.dtsi. It has however been missed that the orion-mdio driver
only supports enabling up to three clocks.
This patch-set allows the orion-mdio driver to handle four clocks and
adds a warning when more clocks are specified to prevent this particular
oversight in the future.
Changes since v1:
- fixed condition for priting the warning (Andrew Lunn)
- rephrased commit description for deferred probing (Andrew Lunn)
- fixed compiler warnings (kbuild test robot)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a warning when device tree specifies more than the maximum of four
clocks supported by orion-mdio. Because reading from mdio can lock up
the Armada 8k when a required clock is not initialized, it is important
to notify the user when a specified clock is ignored.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow up to four clocks to be specified and enabled for the orion-mdio
interface, which are required by the Armada 8k and defined in
armada-cp110.dtsi.
Fixes a hang in probing the mvmdio driver that was encountered on the
Clearfog GT 8K with all drivers built as modules, but also affects other
boards such as the MacchiatoBIN.
Cc: stable@vger.kernel.org
Fixes: 96cb434238 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 8040 needs four clocks to be enabled for MDIO accesses to work.
Update the binding to allow the extra clock to be specified.
Cc: stable@vger.kernel.org
Fixes: 6d6a331f44 ("dt-bindings: allow up to three clocks for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver starts using page_pool buffers before calling
xdp_rxq_info_reg_mem_model(). Start using the buffers after the
registration succeeded, so we won't have to call
page_pool_request_shutdown() in case of failure
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Some improvements and a fix
Some performace improvements (01/03 and 03/03) and a fix (02/03), all for -next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mapping and unmapping DMA region is an high bottleneck in stmmac driver,
specially in the RX path.
This commit introduces support for Page Pool API and uses it in all RX
queues. With this change, we get more stable troughput and some increase
of banwidth with iperf:
- MAC1000 - 950 Mbps
- XGMAC: 9.22 Gbps
Changes from v3:
- Use page_pool_destroy() (Ilias)
Changes from v2:
- Uncoditionally call page_pool_free() (Jesper)
Changes from v1:
- Use page_pool_get_dma_addr() (Jesper)
- Add a comment (Jesper)
- Add page_pool_free() call (Jesper)
- Reintroduce sync_single_for_device (Arnd / Ilias)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a993db88d1 ("net: stmmac: Enable support for > 32 Bits
addressing in XGMAC"), introduced support for > 32 bits addressing in
XGMAC but the conversion of descriptors to dma_addr_t was left out.
As some devices assing coherent memory in regions > 32 bits we need to
set lower and upper value of descriptors address when initializing DMA
channels.
Luckly, this was working for me because I was assigning CMA to < 4GB
address space for performance reasons.
Fixes: a993db88d1 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for coalescing RX path by specifying number of frames which
don't need to have interrupt on completion bit set.
This is only available when RX Watchdog is enabled.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
