Added the AFBC decoder registers for DP500 , DP550 and DP650.
These registers control the processing of AFBC buffers. It controls various
features like AFBC decoder enable, lossless transformation and block split
as well as setting of the left, right, top and bottom cropping of AFBC
buffers (in number of pixels).
All the layers (except DE_SMART) support framebuffers with AFBC modifiers.
One needs to set the pixel values of the top, left, bottom and right
cropping for the AFBC framebuffer.
Cropping an AFBC framebuffer is controlled by the AFBC crop registers.
In that case, the layer input size registers should be configured with
framebuffer's dimensions and not with drm_plane_state source width/height
values (which is used for non AFBC framebuffer to denote cropping).
Changes from v1:
- Removed the "if (fb->modifier)" check from malidp_de_plane_update()
and added it in malidp_de_set_plane_afbc(). This will consolidate all the
AFBC specific register configurations in a single function ie
malidp_de_set_plane_afbc().
Changes from v2:
- For AFBC framebuffer, layer input size register should be set to
framebuffer's width and height.
Changes from v3:
- Rebased on top of latest drm-misc-next
- Some cleanups/sanity changes based on Liviu's comments
Changes from v3 (series):
- Added the ack
- Rebased on the latest drm-misc-next
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patchwork.freedesktop.org/patch/291760/?series=57895&rev=1
Mali-DP650 supports warming up the SMMU translations, by sending
requsts to the SMMU before a buffer is read.
There are two modes supported:
- PARTIAL: could be enabled when the buffer is composed of 4K or 64K
pages, the display hardware will send a configurable number of
requests before the actual reading.
- FULL: could be enabled when the buffer is composed of 1M or 2M
pages, the display hardware will send requests before reading for
all pages composing the buffer.
This patch adds a mechanism for detecting the page size and set the
MMU prefetch mode if possible.
Changes since v1:
- For imported buffers use the already populated
drm_gem_cma_object.sgt instead of calling
driver.gem_prime_get_sg_table, which works just for buffers
allocated through the gem_cma API.
Signed-off-by: Jamie Fox <jamie.fox@arm.com>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[rebased and re-ordered functions]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
When we want to writeback to memory in NV12 format we need to program
the RGB2YUV coefficients. Currently, we don't program the coefficients
and NV12 doesn't work at all.
This patchset fixes that by programming a sane default(bt709, limited
range) as rgb2yuv coefficients.
In the long run, probably we need to think of a way for userspace to
be able to program that, but for now I think this is better than not
working at all or not advertising NV12 as a supported format for
memwrite.
Changes since v1:
- Write the rgb2yuv coefficients only once, since we don't change
them at all, just write them the first time NV12 is programmed,
suggested by Brian Starkey, here [1]
[1] https://lists.freedesktop.org/archives/dri-devel/2018-August/186819.html
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Status register contains a lot of bits for reporting internal errors
inside Mali DP. Currently, we just silently ignore all of the errors,
that doesn't help when we are investigating different bugs, especially
on the FPGA models which have a lot of constraints, so we could easily
end up in AXI or underrun errors.
Add a new file called debug that contains an aggregate of the
errors reported by the Mali DP hardware.
E.g:
[root@alarm ~]# cat /sys/kernel/debug/dri/1/debug
[DE] num_errors : 167
[DE] last_error_status : 0x00000001
[DE] last_error_vblank : 385
[SE] num_errors : 3
[SE] last_error_status : 0x00e23001
[SE] last_error_vblank : 201
Changes since v2:
- Add lock to protect the errors stats.
- Add possibility to reset the error stats by writing anything to the
debug file.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 behaves differently from the rest of the Mali DP IP,
in that it does not have a one-shot mode and keeps writing the
content of the current frame to the provided memory area until
stopped. As a way of emulating the one-shot behaviour, we are
going to use the CVAL interrupt that is being raised at the
start of each frame, during prefetch phase, to act as End-of-Write
signal, but with a twist: we are going to disable the memory
write engine right after we're notified that it has been enabled,
using the knowledge that the bit controlling the enabling will
only be acted upon on the next vblank/prefetch.
CVAL interrupt will fire durint the next prefetch phase every time
the global CVAL bit gets set, so we need a state byte to track
the memory write enabling. We also need to pay attention during the
disabling of the memory write engine as that requires the CVAL bit
to be set in the control register, but we don't want to do that
during an atomic commit, as it will write into the hardware a partial
state.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP display processors are able to write the composition result to a
memory buffer via the SE.
Add entry points in the HAL for enabling/disabling this feature, and
implement support for it on DP650 and DP550. DP500 acts differently and
so is omitted from this change.
Changes since v3:
- Fix missing vsync interrupt for DP550
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Internally Mali DP uses an RGB pipeline so video layers that support
YUV input buffers need to convert the input data to RGB. The YUV
buffers can have various encodings and this patch introduces support
for BT.601, BT.709 and BT.2020 encodings, both limited and full ranges.
This patch adds support for specifying the color encoding of the
input buffers for the planes that are backed by the video layers
and programs the YUV2RGB coefficients into hardware based on the
selected encoding.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[updated to use standard properties]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Apply image enhacement when we are upscaling by a factor of 2
or more in either direction.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.
* Downscaling a plane requires mclk > pxlclk.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
All DPs have a COLORADJ matrix which is applied prior to output gamma.
Attach that to the CTM property. Also, ensure the input CTM's coefficients
can fit in the DP registers' Q3.12 format.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.
This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use rectangle 1 as a generic plane. Existing code already sets the smart
layer bounding box size + offset. The rectangles' offsets are relative
to the bounding box, so there is no need to set R1's offset (reset value
is 0), just its size which is the same as the bounding box.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Hardware has multiple (2 or 3, depending on model) stride
registers per layer; add a function that correctly takes that
into account. On hardware that only has 2 stride registers,
ensure that 3-plane (YUV) content has identical strides
for both chroma planes.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[Removed smart layer stride setup, comment and commit message clarifications]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
If the device-tree 'reg' node doesn't reserve enough
space for the DP, fail to bind.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[renamed added function to malidp_has_sufficient_address_space]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Refuse to bind if the device-tree compatible string
lists a different hardware version.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add support for the new family of Display Processors from ARM Ltd.
This commit adds basic support for Mali DP500, DP550 and DP650
parts, with only the display engine being supported at the moment.
Cc: David Brown <David.Brown@arm.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
