Add LED blinking code to support ethtool -p on the PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that we will always have at least 2 rx rings, 1
will be used as an aggregation ring for TPA and jumbo page placements.
However, it is possible, especially on a VF, that there is only 1 rx
ring available. In this scenario, the current code will fail to initialize.
To handle it, we need to properly set up only 1 ring without aggregation.
Set a new flag BNXT_FLAG_NO_AGG_RINGS for this condition and add logic to
set up the chip to place RX data linearly into a single buffer per packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing hardware RFS mode uses one hardware RSS context block
per ring just to calculate the RSS hash. This is very wasteful and
prevents VF functions from using it. The new hardware mode shares
the same hardware RSS context for RSS placement and RFS steering.
This allows VFs to enable RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new vnic RSS capability will enhance NTUPLE support, to be added
in subsequent patches.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16. We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use native NAPI polling instead. The next patch will complete the work
by switching to use napi_complete_done()
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.
1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success. After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.
2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.
3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device(). A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.
4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.
5. 1 stats context is reserved when the RDMA driver registers. MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.
6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.
v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver register function with firmware consists of passing version
information and registering for async events. To support the RDMA driver,
the async events that we need to register may change. Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible. However, the
user can still increase network rings to the max if he wants. The actual
RDMA resources won't be reserved until the RDMA driver registers.
v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened. So we cannot do
function reset in bnxt_open() which will clear all the resources.
The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one(). This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.
Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode(). bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX. The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By refactoring existing code into this new function. The new function
will be used in subsequent patches.
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report PFC statistics to ethtool -S and DCBNL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support only IEEE DCBX initially. Add IEEE DCBNL ops and functions to
get and set the hardware DCBX parameters. The DCB code is conditional on
Kconfig CONFIG_BNXT_DCB.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest interface has the latest DCB command structs. Get and store the
max number of lossless TCs the hardware can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_setup_mq_tc() to handle MQPRIO. This new function
will be called during ETS setup when we add DCBNL in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer chips have proper support for 4-tuple UDP RSS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port NICs, the speed setting on one port can affect the
available speed on the other port. Add logic to detect these changes
and adjust the advertised speed settings when necessary.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has a limitation that it won't pass host to BMC loopback
packets below 52-bytes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using Ethtool flashdev command, entire NVM package (*.pkg) files
may now be staged into the "update" area of the NVM and subsequently
verified and installed by the firmware using the newly introduced
command: NVM_INSTALL_UPDATE.
We also introduce use of the new firmware command FW_SET_TIME so that the
NVM-resident package installation log contains valid time-stamps.
Signed-off-by: Rob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And remove redundant definitions of the same flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the destination MAC address in the ntuple filter structure. The
current code assumes that the destination MAC address is always the MAC
address of the NIC. This may not be true if there are macvlans, for
example. Add destination MAC address checking and configure the filter
correctly using the correct index for the destination MAC address.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitro A0 has a hardware bug in the rx path. The workaround is to create
a special COS context as a path for non-RSS (non-IP) packets. Without this
workaround, the chip may stall when receiving RSS and non-RSS packets.
Add infrastructure to allow 2 contexts (RSS and CoS) per VNIC. Allocate
and configure the CoS context for Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitro is the embedded version of the ethernet controller in the North
Star 2 SoC. Add basic code to recognize the chip ID and disable
the features (ntuple, TPA, ring and port statistics) not supported on
Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allowable range is 0.25 seconds to 1 second interval. Default is
1 second.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling the firmware to do function reset on the PF will kill all the VFs.
To prevent that, we call function reset on the 1st PF open before any VF
can be activated. On subsequent PF opens (with possibly some active VFs),
a bit has been set and we'll skip the function reset. VF driver will
always do function reset on every open. If there is an AER event, we will
always do function reset.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port number for GENEVE is hard coded into the bnxt driver. This is the
kind of thing we want to avoid going forward. For now I will integrate
this back into the port notifier so that we can change the GENEVE port
number if we need to in the future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cards do not support autoneg. The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bnxt_gro_func_5731x() to handle GRO packets for this chip. The
completion structures used in the new chip have new data to help determine
the header offsets. The offsets can be off by 4 if the packet is an
internal loopback packet (e.g. from one VF to another VF). Some additional
logic is added to adjust the offsets if it is a loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require different logic to handle GRO packets. So refactor
the code so that we can call different functions depending on the chip.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define all the supported chip numbers and chip categories. Store the
chip_num returned by firmware. If the call to get the version and chip
number fails, we should abort.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPAR type is read from bnxt_hwrm_func_qcfg. Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions. The link parameters are set up by firmware.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver gets this event, the VF configuration has changed (such
as default VLAN). The VF driver will initiate a silent reset to pick up
the new configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.
Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status. Delete
the unnecessary last_port_module_event. Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Add detection and recovery code when the hardware returned opaque value
does not match the expected consumer index. Once the issue is detected,
we skip the processing of all RX and LRO/GRO packets. These completion
entries are discarded without sending the SKB to the stack and without
producing new buffers. The function will be reset from a workqueue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a rare hardware bug that can cause a bad opaque value in the RX
or TPA completion. When this happens, the hardware may have used the
same buffer twice for 2 rx packets. In addition, the driver will also
crash later using the bad opaque as the index into the ring.
The rx opaque value is predictable and is always monotonically increasing.
The workaround is to keep track of the expected next opaque value and
compare it with the one returned by hardware during RX and TPA start
completions. If they miscompare, we will not process any more RX and
TPA completions and exit NAPI. We will then schedule a workqueue to
reset the function.
This patch adds the logic to keep track of the next rx consumer index.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD. Divide the page
into multiple 32K buffers for the aggregation ring.
Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer. Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535. For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers. It won't work if the native CPU page size is
64K or bigger.
We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.
The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10GBaseT devices must autonegotiate to determine master/slave clocking.
Disallow forced speed in ethtool .set_settings() for these devices.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the PORT_CONN_NOT_ALLOWED async event handling logic. The driver
will print an appropriate warning to reflect the SFP+ module enforcement
policy done in the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the
parameter is set, it will call bnxt_hwrm_set_eee().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get EEE capability and the initial EEE settings from firmware.
Add "EEE is active | not active" to link up dmesg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
