This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
enable the dma support for auart0 in mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Globalscale Mirabox platform has two Ethernet interfaces,
connected to the SoC with a RGMII interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The PlatHome OpenBlocks AX3-4 platform has 4 Ethernet ports, connected
to a single quad-port PHY through SGMII.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch enables the two network interfaces of the Armada 370
official Marvell evaluation platform, and the four network interfaces
of the Armada XP official Marvell evaluation platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Armada 370 SoC has two network units, while the Armada XP has four
network units. The first two network units are common to both the
Armada XP and Armada 370, so they are added to armada-370-xp.dtsi,
while the other two network units are specific to the Armada XP and
therefore added to armada-xp.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Having labels before each node allows board bindings to reference
to nodes by using the &nodename {} notation. This way boards do not
have to resemble the whole devicetree layout. Due to less indention
needed the board files also get better readability. Since the label
make the documentation behind the nodes unnecessary it is removed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch supplements pinctl support on i.MX53.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Setup the GPIO7_11 pin as interrupt to the DA9053 and also rename the regulator nodes
so that they match with the datasheet.
This allows probing of DA9053 to succeed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.2: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to Documentation/devicetree/bindings/mmc/mmc.txt bus-width
is a mandatory property. While this is currently enforced nowhere, it's
a good habit to just add the property now to allow to add common helper
functionality for the mmc property parsing later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
convert at91sam9g20ek with wm8731 to device tree support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the host1x node along with its children to the Tegra30 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the host1x node along with its children to the Tegra20 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Nvidia's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add DT entry for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: move sflash node to keep file sorted]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Harmony board has an ON Semiconductors NCT1008 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tamonten SOM has an ON Semiconductor NCT1008 connected to the DVC
bus which is used to measure the ambient (local) temperature as well as
the on-die (remote) temperature.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Harmony board has an Analog Devices ADT7461 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
These properties are already set by the tegra20-tamonten.dtsi, so they
don't need to be repeated.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This commit allows the I2C2 controller on Tegra20 to be routed either to
the DDC or the PTA pin group at runtime. On Tamonten this allows the I2C
bus to be used for the DDC of the HDMI connector or to access I2C chips
on the carrier board.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.
SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add slink controller details in the dts file of
Tegra20 and Tegra30.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra 2's I2C2 controller can be routed to either the PTA
or DDC pin group on Ventana. So:
- Remove the HDMI function definition of pta pingroup
- Define child i2c adapters(ddc & pta) for I2C2 controller
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Configure pinmux as required for WiFi.
Enable the SDHCI1 controller for a02 and a04 board, which is connected to the
WiFi module.
For now, always enable the regulator that provides power to the Wifi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Configure pinmux as required for WiFi.
Enable the SDHCI1 controller, which is connectted to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable the SDHCI1 controller. This is connected to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
various .dts files, and timer related changes to allow
configuring the timer via device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQoYD5AAoJEBvUPslcq6VzHtAP/1mzXjyRJX9NDh3S7ueO4njz
guCeaTIBjYwXBSASpfhWLOgFWLE4YGpAZstp+ZLHkzh8EN/yV5ZkodoJo3wYnwma
V3qkj9oLONqCTkuXr3Gxhl/xLR4Q/WfJItIw0Ok4v12n1NRMoeKvQIpYznO+klAk
i6ztZNfr+v6+EbFcjUW4kxXKjssW2MySAEW1/x1vQSdffMnIvioVjthD16lER+A3
fHkhSSmHkUH9UdZiclzuZd3N+/J8YX8Q2yUWI8wHeVuCgnn3QFRZ3p9ngCd6a5lm
jIbzazJq5gJjidBkSPef6CeNt6nbj0MmtPePxniMeW/cLdbQcibzhAlW5KWZ71+Q
rD1WlcR5jrUdzSIG3UjvhGRFN0LcegVJvMgqM5h5IYbZETLA/Gcp2gszyYKovU3B
tHEXEmwhSciM5PC/x2o1cZGqdf2sCl5i+5esI+sbJxI4GjtLkJiFNoBgjrek9anu
dTqIK1/AlKIQGbDPAmAJXjKKM8hq+3r/PWzRUipXxORlArT1uRI8SzvR76mISAwL
kCSKPCwwbY3DDozTwSFPynZpFgkZHI0rW00poBNpG7ev18IFUJinSHeY1Jqssgfb
1XguV4Txc1IrlICk+bi+Y7bogoeWjXl3cIvWkdAkZKWF75Irh4zZSRyI5+DWN8Bi
stnGo1JUqE1K7j4HEIHi
=59qq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren <tony@atomide.com>:
Device tree related changes for omaps updating the
various .dts files, and timer related changes to allow
configuring the timer via device tree.
* tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (48 commits)
usb: musb: dsps: dt binding - add resources, example
ARM: dts: omap4-sdp: Add pinmux configuration for HDMI
ARM: dts: omap4-panda: Add pinmux configuration for HDMI
ARM: dts: Makefile: Add the am335x-evmsk target in dtbs list
ARM: dts: AM33XX: Add usbss node
ARM: dts: AM33XX: Add push-buttons device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-keys to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-leds to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-bone
ARM: dts: AM33XX: Add pinmux configuration for user-leds to BONE
ARM: dts: AM33XX: Add volume-keys device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for volume-keys to EVM
ARM: dts: AM33XX: Add matrix keypad device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for matrix keypad to EVM
ARM: dts: omap5-evm: LPDDR2 memory device details for EVM
ARM: dts: omap5: EMIF device tree data for OMAP5 boards
ARM: dts: omap5-evm: Fix size of memory defined for EVM
ARM: OMAP2+: Add device-tree support for 32kHz counter
ARM: OMAP: Add DT support for timer driver
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds device tree properties for ST-Ericsson DB8500 thermal driver,
also adds the platform data to support the old fashion.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add CPSW and MDIO related device tree data for AM33XX.
Also enable them into board/evm dts files by providing
respective phy-id.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the Device Tree files for Armada 370 and XP SoCs and boards use
the "armada-370-xp" common compatible string, except
armada-370-xp.dtsi which was specifying "armada_370_xp".
Fix this inconsistency by making armada-370-xp.dtsi declare a
compatible string of "armada-370-xp" like everyone else.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This platform, available from Globalscale has an Armada 370. For now,
only the serial port is supported. Support for network, USB and other
peripherals will be added as drivers for them become available for
Armada 370 in mainline.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
This is 3.8 material.
Changes from original version posted by Gregory:
* Renamed .dts file to armada-370-mirabox.dts
* Change compatible string to 'globalscale,mirabox'
* Remove compatible string from armada-370-xp.c
* Removed references to MBX0001
This platform, available in Japan from PlatHome, has a dual-core
Armada XP, the MV78260. For now, only the two serial ports and the
three front LEDs are supported. Support for SMP, network, SATA, USB
and other peripherals will be added as drivers for them become
available for Armada XP in mainline.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
This is 3.8 material.
Changes since v2:
* Renamed the .dts file to armada-xp-openblocks-ax3-4.dts
* Removed the compatible string from armada-370-xp.c (which now only
lists the common SoC compatible string)
Changes since v1:
* Renamed the board to OpenBlocks AX3-4, since there is a variant
called AX3-2 which has less RAM, and no mini PCIe port. Requested
by Andrew Lunn.
* Fix the amount of memory to 3 GB. In fact, the board has 1 GB
soldered, and 2 GB in a SODIMM slot (which is therefore
removable). But as the board is delivered as is, we'll assume it
has 3 GB of memory by default.
Add support for retrieving TTC configuration from device tree. This
includes the ability to pull information about the driving clocks from
the of_clk bindings.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Make the Zynq platform use the newly created zynq clk bindings.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Since commit edc88ceb0 (ARM: be really quiet when building with 'make -s') the
following output is generated when building a kernel for ARM:
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
Building modules, stage 2.
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
As per Documentation/kbuild/makefiles.txt the correct way of using kecho is
'@$(kecho)'.
Make this change so no more unwanted 'echo' messages are displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The purpose of the created zynq-7000.dtsi file is to describe the
hardware common to all Zynq 7000-based boards. Also, get rid of the
zynq-ep107 device tree, since it is not hardware anyone can purchase.
Add a zc702 dts file based on the zynq-7000.dtsi. Add it to the
dts/Makefile so it is built with the 'dtbs' target.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This adds a i.MX25 dtsi file along with the i.MX25 clock tree
documentation. The devicetree should be fairly complete for:
- uart
- fec
- i2c
- spi
- pwm
- nand
- gpio
- wdog
- esdhc
- flexcan
The more exotic devices currently miss clock bindings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Commit edc88ceb0c silenced the make -s build, but
inadvertently made louder the non-silent build. Fix by prepending '@' to each
of the added $(kecho) statements.
Build with edc88ceb0c:
CHK include/generated/compile.h
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
Build with this fix:
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the pinmux configuration for HDMI and TPD12S015A. Configure the
gpios for the TPD12S015A and SDA, SCL and CEC for HDMI.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the pinmux configuration for HDMI and TPD12S015A. Configure the
gpios for the TPD12S015A and SDA, SCL and CEC for HDMI.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add atmel-ssc for device tree support
Match "atmel,at91rm9200-ssc" for using pdc for data transfer
Match "atmel,at91sam9g45-ssc" for using dma for data transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a minimal board dts file for Samsung EXYNOS4412 based SMDK board.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree sources for EXYNOS4X12 SoC series
(currently EXYNOS4212 and EXYNOS4412) and enables mach-exynos4-dt
to support these SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQkXPDAAoJEMhvYp4jgsXinuYH/R0+02Xe5UOAxQR1JtAt4ppy
OHoMhJWs2UJyXBktRX53YBSCiiPUSJDU9u2XOPqBXMwjTeeyeao8BMxJ4WewkdQc
5VmQlPvFRBdn0npIN+RSB7khYbtfLpVK6GhRve/Evf045bU0UztDvAMHUodFDu8J
GFd4X326y3OVSRZyImUinvX27gIPRQuSxNrVqvOC22FivBYEgliT05A/TTZmV2FF
jcEJr4Z0tZF1rOlRilMHORTyLAnMk5eTgKp5moc57tW8/nkq5vrdPtfYejmUveKx
mTh6yVsnI3x29sMvZZlVyT5CsRcB+on4O2P7aiUx4iajtAArAuXOZD3wOeO2PNU=
=2oPL
-----END PGP SIGNATURE-----
Merge tag 'calxeda-ecx-2000' of git://sources.calxeda.com/kernel/linux into next/soc
Support for Calxeda ECX-2000 SOC from Rob Herring
* tag 'calxeda-ecx-2000' of git://sources.calxeda.com/kernel/linux:
ARM: highbank: Add initial ECX-2000 support
ARM: highbank: abstract out SCU usage
ARM: smp_twd: don't warn on no DT node
ARM: dts: Add Calxeda ECX-2000 support
ARM: highbank: enable coherent DMA for xgmac in dts
ARM: highbank: disable unused sdhci and gpio in dts
+ sync to Linux 3.7-rc3
Device tree node for usbss on AM33XX. There are two musb
controllers on am33xx platform so have port0-mode and
port1-mode data.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[afzal@ti.com: reg & interrupt property addition]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add gpio based push buttons device tree data to am335x-evmsk device
by adding all the necessary parameters like key-code, gpios and etc.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio based keys to am335x-evmsk. In
this patch, only single named mode/state is added and these pins
are configured during pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add gpio-leds device tree data to am335x-evmsk device to enable gpio
based user-leds (USR0, USR1, USR2 and USR3) present on am335x starter
kit.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio based volume keys to am335x-evmsk.
In this patch, only single named mode/state is added and these pins
are configured during pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add gpio-leds device tree data to am335x-bone device to enable gpio
based user-leds (USR0, USR1, USR2 and USR3) present on BeagleBone.
[koen@dominion.thruhere.net: led0, led1 suggested by koen]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio based user-keys to am335x-bone.
In this patch, only single named mode/state is added and these pins
are configured during pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add gpio based volume keys device tree data to am335x-evm by adding
all the required parameters like keycode, gpios and etc.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio volume keys. In this patch, only
single named mode/state is added and these pins are configured during
pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add matrix keypad device tree data to am335x-evm by adding all
the necessary parameters like keymap, row & column gpios and etc.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio matrix keypad. In this patch, only
single named mode/state is added and these pins are configured during
pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7377 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Commit 13511de "regulator: deprecate regulator-compatible DT property"
now allows for simpler content within the regulators node within a PMIC.
Modify all the Tegra device tree files to take advantage of this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Samsung's K3PE0E000B memory part is used in OMAP5-evm board.
Adding timings and geometry details for Samsung's memory part and
attaching the same to device-handle of EMIF1/2.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Memory present for OMAP5-evm is 2GB. But in dts file
it is specified as 1GB. Correcting the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
The way the VE motherboard Device Trees were constructed
enforced naming and structure of daughterboard files. This
patch makes it possible to simply include the motherboard
description anywhere in the main Device Tree and retires
the "arm,v2m-timer" alias - any of the motherboard SP804
timers will be used instead.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Add description of all functions provided by Versatile Express
motherboard and daughterboards configuration controllers and
clock dependencies between devices.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
The zynq-7000 has an additional UART at 0xE0001000. Describe it in the
device tree.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Use a hog_pins pinctrl group to force the muxing of GPIOs used on the
Crystalfonz CFA10036 and CFA10049 boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The leds-gpio driver recently got pinctrl support, so setup the power
led gpio muxing through pinctrl.
This avoids the warning:
leds-gpio leds.X: pins are not configured from the driver
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is no driver for it yet, so it will use spidev.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add ENET 1588 clock input pin
MX6Q_PAD_GPIO_16__ENET_ANATOP_ETHERNET_REF_OUT
and anatop PLL8 clock source for ENET
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For OMAP4 devices, timers 5-8 have both a L3 bus address and a Cortex-A9
private bus address. Currently the device-tree source only contains the
L3 bus address for these timers. Update these timers to include the
Cortex-A9 private address and make the default address the Cortex-A9
private bus address to match the current HWMOD implementation.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add McSPI data node to AM33XX device tree file. The McSPI module (and so
as the driver) is reused from OMAP4.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Tested-by: Matt Porter <mporter@ti.com>
[b-cousson@ti.com: Remove interrupt-parent]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
On boot the Nomadik GPIO controller complains that an IRQ can't be
configured as active high level-sensitive, so this patch converts
it to be low-to-high edge triggered instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a very simple mechanism to change and SDI's voltage which
consists of toggling some GPIOs. This scenario can be better handled
if we convert it to a GPIO regulator. This patch provides one which
can be read from Device Tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
So far, each ST-Ericsson board supported by Device Tree has been similar
enough to run though a single DT_MACHINE_INIT call. On the back of that
it has been suggested that we should reduce the number of compatible
strings in our dt_compat structure. After subsequent discussion with Arnd
Bergmann the conclusion was to list entries by platform as opposed to by
board.
The other suggestion was to use a single string which would cover all
supported platforms, but any wildcard entries would include unsupported
chipsets, such as the u5500 and potential new chips which no not yet have
DT functionality. Hence, the best solution which encompasses all supported
platforms, but no unsupported ones was to list the currently enabled four
chipsets; u8500, u8540, u9500 and u9540 instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When enabling ST-Ericsson's ccu9540 development board the board's
full name has not been used. This patch adapts all references of
the board's short name to how it should be referenced.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the 3 UART nodes required to enable serial ports on the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch allows the STMPE keypad driver to be successfully probed
and initialised during a Device Tree enabled boot sequence. It
contains all of the required properties needed to setup and map
each key on the 6x3 keypad located on the ST User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we apply the STMPE Multi-Functional Device's node to the
ST User Interface Board Device Tree file. It includes all of
the properties required for correct device initialsation.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible to connect a BU21013 Touch Screen to all version
of the HREF which support the ST-UIB. This patch applies all the
necessary settings to the pre-v60 and v60+ HREF Device Trees.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a skeleton creation which will be populated with the devices
found on one of ST-Ericsson's (UIB) User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we ensure the SFH7741 Proximity Sensor is registered through
gpio-keys when booting with Device Tree enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In ux500 platform code we currently support a number of devices.
Two of these devices are fairly similar, but have key differences.
Early (pre-v60) HREFs and the more up-to-date versions (v60+), and
they both need to be supported by Device Tree. Here we apply a DT
source file for the earlier versions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are two main versions of the ST-Ericsson hardware reference board,
each with subtle differences. These versions are described in current
platform data as 'mop500' for HREF v1.1 & v2.0 and 'hrefv60+' for latter
incarnations. However, the boards have much in common, so this patch
creates a .dtsi (Device Tree Source Include) file which describes the
similarities between the two boards and individual 'hrefprev60' and
'hrefv60plus' .dts files which depict the differences.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Snowball's external SD/MMC slot is only capable of 4 bit data
transfer, not 8 bits as previously thought. This is a simple
fixup moving to the correct settings.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the DB8500 Reference Manual SDI devices are described as being
part of peripheral blocks. This is more in line with how these devices
are actually represented in hardware, so here we detail which
peripheral block each of the SDI devices belong in the node name.
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The APF28Dev is a docking board for an APF28 SOM
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Separate out common dts pieces from highbank dts and add support for
Calxeda ECX-2000 (Midway) SOC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Enable the xgmac to use the coherent DMA path in highbank.dts
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
These peripherals are not enabled in current systems, so turn them off.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The reg property contains <base length> not <base last_offset>. Fix
the length values to be length not last_offset.
Cc: stable@vger.kernel.org
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use DT_MACHINE_START() on the sh7372 based mackerel board.
Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Rename the files to have names consistent across OMAP boards.
Update the Makefile to use the new name.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add base address and interrupt line inside Device Tree data for
OMAP5.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add base address and interrupt line inside Device Tree data for
OMAP5.
Fix as well the wrong compatible string on UART5 & 6.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[b-cousson@ti.com: Update the changelog to reflect the fixes
done in the patch]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add base address and interrupt line inside Device Tree data for
OMAP5
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add base address and interrupt line inside Device Tree data for
OMAP5.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Adds the counter-32k timers nodes present in OMAP2/3/4 devices and
device-tree binding documentation for OMAP counter-32k.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the 12 GP timers nodes present in OMAP2.
Add the 12 GP timers nodes present in OMAP3.
Add the 11 GP timers nodes present in OMAP4.
Add the 7 GP timers nodes present in AM33xx.
Add documentation for timer properties specific to OMAP.
Thanks to Vaibhav Hiremath for creating the AM33xx timer nodes. I have modified
Vaibhav's original nodes adding information on which timers support a PWM
output.
V5 changes:
- Updated timer register sizes for OMAP2/3/4.
- Modified AM335x timer register size to be 1KB instead of 4KB to align with
HWMOD.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-Reviewed-&-Tested-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
The interrupt-parent attribute does not have to be added in each
node since the fmwk will check for the parent as well to get it.
Create an interrupt-parent for OMAP2, OMAP3, AM33xx and remove the
attributes from every nodes that were using it.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sebastien Guiriec <s-guiriec@ti.com>
*reg* property for ocp2scp was previously obtained from ti,hwmods property.
But that is now explicitly added to the dt node.
Also updated the documentation with *reg* info.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add twl4030-usb data node in twl4030 device tree file. twl4030-usb is the phy
driver for MUSB used in omap3 chipsets. The dt data is comprised of two
interrupts, one for ID and one for VBUS and three phandles to regulator.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add twl6030-usb data node in twl6030 device tree file. twl6030-usb is the
comparator driver for USB that detects VBUS and ID events. The dt data is
comprised of two interrupts, one for ID and one for VBUS and a phandle to the
regulator.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add AM335X EVM-SK device tree source (am335x-sk.dts) file to use
the am33xx.dtsi SoC file, along with the memory node information.
Also adds support for tps65910 regulator and lis331dlh accelerometer.
Following drivers/functionality were tested on AM335x-EVM-SK.
* I2C
* TPS65910 regulators
* lis331dlh accelerometer
AM335x EVM Starter Kit details can be accessed from:
http://www.ti.com/tool/tmdssk3358
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.
TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add Bosch D_CAN controller device tree data to AM33XX dtsi
file by adding d_can device nodes with all the necessary
parameters.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Adds basic pinctrl device tree data for AM33XX family of devices.
This patch is based on the pinctrl-single driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.
Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.
This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.
V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
configuration
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
This patch adds support for device tree based discovery for exynos5
hdmi ddc.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree based discovery for exynos5
hdmiphy.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree based discovery for exynos5
mixer. Mixer node is also renamed with "exynos5-mixer".
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree based discovery for exynos5
hdmi. Hdmi node is also renamed with "exynos5-hdmi".
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds necessary source definations needed for TMU driver and
adds devicetree node for exynos5250.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[kgene.kim@samsung.com: used address value directly in auxdata]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds necessary source definations needed for TMU driver and
adds devicetree node for exynos4210.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This board supports:
- AM1808 based board
- 64 MiB DDR ram
- 2 MiB Nor flash
- 128 MiB NAND flash
- use internal RTC
- I2C support
- hwmon lm75 support
- UBI/UBIFS support
- MMC support
- USB OTG support
This patch adds the basic DTS file enabling the serial ports.
Other features will be added in due course of time.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
[nsekhar@ti.com: modified after dtsi refactoring and added binding
documentation]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add DT data for DA850 SoC. Only interrupt controller and
serial port information is being added at this time.
Signed-off-by: Heiko Schocher <hs@denx.de>
[nsekhar@ti.com: refactored DT data into SoC specific and
board specific and include SoC data into .dtsi file]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Zynq has a PL310 L2 cache controller. Convert in-tree uses to using
the device tree.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Cc: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>
The Zynq uses the cortex-a9-gic. This eliminates the need to hardcode
register addresses.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Cc: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we
had a few of these patches cause regressions themselves and had to
work out how to deal with those in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IDdm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
From Kukjin Kim <kgene.kim@samsung.com>:
One is spi stuff for fix the device names for the different subtypes of
the spi controller. And the other is adding missing .smp field for
exynos4-dt and fixing memory sections for exynos4210-trats board.
* 'v3.7-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set .smp field of machine descriptor for exynos4-dt
ARM: dts: Split memory into 4 sections for exynos4210-trats
ARM: SAMSUNG: Add naming of s3c64xx-spi devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable GPIO and pinctrl in Kconfig.
Add required <mach/gpio.h> for gpiolib.
Instantiate the BCM2835 GPIO module in bcm2835.dtsi.
Add a pinctrl definition to bcm2835-rpi-b.dts that sets up all of the
board's required pinmux configuration. GPIO aren't specified; that's
left to gpio_request().
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Implement the machine restart hook using the SoC's watchdog timer module.
To support this, define a DT binding for the watchdog module, and add it
to the device tree.
The downstream rpi-split branch contains a full watchdog timer driver
implementation, which also implements the restart hook. However, the
restart function is largely separate from the watchdog driver, so for
simplicity, the restart hook is implemented here directly in the main
machine source file.
Overall structure (separate setup/restart) functions derived from the
picoxcell ARM support.
Watchdog register IO sequence taken from code by Simon Arlott. Note that
the watchdog module is not documented in BCM2835-ARM-Peripherals.pdf.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
mux and pinctrl fixes, and Beagle OPP fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQiDFhAAoJEBvUPslcq6VzWaoP/iLrCUkSv/7e3Y+r/59B7xPD
D4Uco/7dBE7m8ropaDgeLJRugXCF3SCJjDaHwKhQFImdQCkaN7wXdfiECEx0Qgk4
kU6qD1amNd304XbAjDNn49jzAd83n3BedcvPjt5uea35na7Jo34n1IxDw8iJ2ZjB
UGpBccOFErXEgzXGB6CVh3gJcD8LasM6zkyfQJDTOkT0+eLeRGlktwwxLyEbxBsp
mp0+6bz4L+IdeP3tlhp1Ta4qRVd8J1A1fQ6L3Sv/IxIDjsUNX0WYMRJqjjiFXvBF
rE65unZIwRBDXjstsicwYlAgmFnvzdeVE5G6hqrkdWhU96iWXJwa1t2nboroSt43
t1k8MU8RE1BD3g2U5JIpjNqp6r2l6bI3Uf/RQ6UPWvtyszIPjm/xpqlVrDplmGvE
7yq0iPVft2dikXUIZ7mS+2JagqmTvEbFS/upPjCx77Z+USrbbXmC3/0Yvs+40AeO
nHkbk9o3ZLXOph9631csKkZhMXJzu3V3D8UCoLM2ce+pZDEqTYC4zmwkHRI8KNIl
02VnDTm4eunarFKSIn/G0srShKsOjxnOUS2Q094tEHg2LopSfP0gDZ3y124pefm9
/IXPSRLOtGatwCjfjuyai7EaWU/vLeTF9mYSH+RLWxA7xHQDJZhzqxvD/PNjWN9r
5rExktjgajQKaNhKdMMB
=GIXH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc2/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Timer fix for am33xx, runtime PM fix for UART, audio McBSP fixes,
mux and pinctrl fixes, and Beagle OPP fix.
* tag 'omap-for-v3.7-rc2/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
ARM: OMAP3: Beagle: fix OPP customization and initcall ordering
ARM: OMAP3: Fix 3430 legacy mux names for ssi1 signals.
ARM: OMAP2+: Fix location of select PINCTRL
ARM/dts: omap3: Fix mcbsp2/3 hwmods to be able to probe the drivers for audio
ARM: OMAP2: UART: fix console UART mismatched runtime PM status
ARM: OMAP3: PM: apply part of the erratum i582 workaround
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The most important ones are a duplicated definition of a Kconfig
variable and the handling of external interrupts for non-DT case.
The new at91sam9g10 was suffering a recognition issue due to an ID
mis-interpreted: this was leading to a kernel panic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQiPCWAAoJEAf03oE53VmQHZcH/2cAmpXeCoLwtpmRs0WpumtN
OnIVB0W4EchnCUSfd19q4FiUANfPFAxRN0yxx8Sby4wUMUMKnAu6eLebhumeBl6i
L/80KDwIUOhxXCt8YV9tjH1sGDddiG8oQWLF9wfKTIAyTNKcG3usuxq/bTooiXnE
8i1dYvM0w9A7vseYDOOzDgapslStJUBaaZllNddhyP/FyGJZopGb6ObhI1PLeyTJ
iRLA5+NeFAdHIV7y875JlIWacfzQxEa0u2cptVAz9ZmYobesTZJkhzGAjpFEwUB1
bGktll0opy+2pPg8JFqZLC/qdYzVZJxSBWbT/zA2amf8asN4NFReTxHnsh81Rfs=
=AgpJ
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre <nicolas.ferre@atmel.com>:
A mix of typos and critical fixes.
The most important ones are a duplicated definition of a Kconfig
variable and the handling of external interrupts for non-DT case.
The new at91sam9g10 was suffering a recognition issue due to an ID
mis-interpreted: this was leading to a kernel panic.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91: (257 commits)
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current DT nodes for mx23/mx28 miss the `clocks-names` item for gpmi-nand.
So the gpmi-nand driver could not find the proper clock.
This patch fixes this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we fix a simple copy and paste error and bring some node
spaces back into line with the remainder of the tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now the Nomadik I2C driver has been converted to an AMBA one, we
are required to provide the Primecell IDs via platform code. When
booting with DT enabled these have to be specified in the device
nodes. We do that here.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following errors:
[ 2.318084] omap-mcbsp 49022000.mcbsp: invalid rx DMA channel
[ 2.324432] omap-mcbsp 49024000.mcbsp: invalid rx DMA channel
Which is because we failed to link the sidetone hwmod for McBSP2/3. The
missing sidetone hwmod link will prevent omap_device_alloc() to append the
DMA resources since we - accidentally - end up having the same number of
resources provided from DT (IO/IRQ) as we have in hwmod for the McBSP ports
without the ST resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The APF28 is a small SOM built around an i.MX28 processor with 128MBytes DDR2,
256MBytes NAND Flash and an Ethernet PHY.
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds device tree entry for MFC v6 in the Exynos5
SoC. Makes the required changes in the clock files and adds
MFC to the DT device list.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[kgene.kim@samsung.com: fixed section mismatches Seung-Woo Kim reported]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change event type to switch for the power and autopower switches.
Additionally, this patch aligns the keycodes with the other linkstation
boards already supported by linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Don't use the specific board name in a the common device tree include file.
Instead use the common name 'lsxl'.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Based against v3.7-rc1
- Latest changes to arch/arm/mm/cache-tauros2.c
c2b7e05 ARM: cache: add dt support for tauros2 cache
Misc. fixes for latest changes to mach-dove/
Fixes build breakage for mach-dove
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQfutwAAoJEAi3KVZQDZAeJlYH/2n8rEqGCrZuU16XVl3Hwc5q
mUkF0PexHDnGGNrgfOEAIaouG3rCTVVdj+NTqnz3gK8jaJHF06tfhpwZaxymDFzW
m4Lt45IuDvU5jEuCBm1IDHWHLro/73YepZJJRt9yAwI1DdWAhUBYLS8cd7fIoLAJ
th0TI7PObmHRVlY2mS+ByuU5wnqV5mJMMPN6oU4RzO91rNuhoQRm8WvjzEs+tSfU
GluD05p/bm3dL9Aq6146h80CZn3W4SVIKeS2l/GdQV6bqaIUvsp0F3xfzggcrcLF
rZxOom72BgnEzA1enu+adJwKY8dHxOAZ4Iuf4HUXI5DKVfVCOrmJmWfp0mS8oyc=
=RP8E
-----END PGP SIGNATURE-----
Merge tag 'mvebu_dove_late_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
Misc. fixes for latest changes to mach-dove/
Fixes build breakage for mach-dove
* tag 'mvebu_dove_late_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux:
ARM: dove: Add crypto engine to DT
ARM: dove: Remove watchdog from DT
ARM: dove: Restructure SoC device tree descriptor
ARM: dove: Fix clock names of sata and gbe
ARM: dove: Fix tauros2 device tree init
ARM: dove: Add pcie clock support
Make use of DT support for the crypto engine on dove and remove
the obsolete init call.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The watchdog on dove requires an interrupt that is not yet
available on DT. Therefore, the watchdog DT node is removed
until the corresponding chained intc is available.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds proper ranges for all mapped addresses within
dove SoC and moves the interrupt controller node inside the simple-bus
node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During the review process of dove DT patches, Tauros2 cache
init call was changed and DT support added. This patch fixes
the call to Tauros2 init and adds a DT node. Moreover, plat/irq.h
include was missing from mach-dove/common.c.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds status override of serial nodes to enable used
serial ports on Origen and SMDKV310 board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the maximum section size on mach-exynos is set to 256MiB, boards
with memory configuration defined using sections bigger than 256MiB will
fail to boot with a kernel panic.
This patch modifies the dts file of Samsung Trats board to define four
sections of 256MiB instead of two of 512MiB to fix the boot problem.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Removes a few unused headers from include/mach
Removes unused arm/boot/compressed/head-vt8500.S
Fixes header text in mach-vt8500/timer.c
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQe2KiAAoJEAKiPfwuf9N/secH/0zr7mg17kgXxOflI/PSjwES
QvYOsT+iR3qAN4KX27Dev7waZaBnfEwDUyVUPc/NYuAz5PjuFA6/6O3wlWEz3tvT
zn2dgrKNaG6wEvmJjVEh7Ec7mP4Ztz9uNgV49A4s26yXj28kETgPXY+QV+hJA2Ct
LBILW2KmyfgHzIYc3OryXMyuTlB23HseI0e6/pe1KcFmGJXyykW2/wUR8gtc5yoW
9R9eeMPjw8olNLy7I2iuGIXiFC0BWYol7Wx5e9mvWfxfEXSSnvOurw0NKKB9GL1G
RCVLFbJPJX2HMITQn2n6SV+cGalTZ9V0WupyU/WVUWSJnYEfciQubk2mwQEs4Y4=
=1L0P
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.8' of git://server.prisktech.co.nz/git/linuxwmt into next/cleanup
From Tony Prisk: Cleanup for 3.8
Removes a few unused headers from include/mach
Removes unused arm/boot/compressed/head-vt8500.S
Fixes header text in mach-vt8500/timer.c
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
* tag 'cleanup-for-3.8' of git://server.prisktech.co.nz/git/linuxwmt:
vt8500: Fix header in mach-vt8500/timer.c
vt8500: Remove arm/boot/compressed/head-vt8500.S
vt8500: Remove unused headers from include/mach/
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 9e3c0066 (ARM: dts: imx6q-arm2: add pinctrl for uart and enet)
defines NANDF_CS pins as gpio in 'hog', assuming these two pins are
always used by usdhc3 in gpio mode as card-detection and
write-protection on ARM2 board. But it's not true. These pins are
shared by usdhc3 and gpmi-nand. We should have the pins functional
for gpmi-nand when usdhc3 is disabled.
Move the pins out of 'hog', so that pins only work in gpio mode as CD
and WP when usdhc3 is enabled, and otherwise they are available for
gpmi-nand.
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
EHCI and UHCI devices in wm8505.dtsi should use IRQ 1 & 0
respectively - not 43 as used on newer models.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
This makes sure that the ARM Integrator device trees get compiled
during build.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch reworks wake-up interrupt handling in pinctrl-exynos driver,
so each pin bank, which provides wake-up interrupts, has its own IRQ
domain.
Information about whether given pin bank provides wake-up interrupts,
how many and whether they are separate or muxed are parsed from device
tree.
It gives following advantages:
- interrupts can be specified in device tree in a more readable way,
e.g. :
device {
/* ... */
interrupt-parent = <&gpx2>;
interrupts = <4 0>;
/* ... */
};
- the amount and layout of interrupts is not hardcoded in the code
anymore, but defined in SoC-specific structure
- bank and pin of each wake-up interrupt can be easily identified, to
allow operations, such as setting the pin to EINT function, from
irq_set_type() callback
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of registering one IRQ domain for all pin banks of a pin
controller, this patch implements registration of per-bank domains.
At a cost of a little memory overhead (~2.5KiB for all GPIO interrupts
of Exynos4x12) it simplifies driver code and device tree sources,
because GPIO interrupts can be now specified per banks.
Example:
device {
/* ... */
interrupt-parent = <&gpa1>;
interrupts = <3 0>;
/* ... */
};
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It allows particular banks to be
specified using their phandles.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.5: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The initial state of the gpio led can be set directly in "gpios" node.
Hence, linux,default-trigger can be removed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.12: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
Set the dbgu pinctrl config by default as we have only one possible config
For other uart set the rxd/txd by default.
For at91sam9x5ek create soc based dts as we need to include specific soc dtsi.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
On the at91sam9x5 SoC series, GPIO banks B and D only have 19 and 22
pins. So add a property to set this parameter.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Fix also the reg size as we have 512 bytes bank not 256 bytes per gpio/mux
controller
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Pull second set of ARM updates from Russell King:
"This is the second set of ARM updates for this merge window.
Contained within are changes to allow the kernel to boot in hypervisor
mode on CPUs supporting virtualization, and cache flushing support to
the point of inner sharable unification, which are used by the
suspend/resume code to avoid having to do a full cache flush.
Also included is one fix for VFP code identified by Michael Olbrich."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels
ARM: 7549/1: HYP: fix boot on some ARM1136 cores
ARM: 7542/1: mm: fix cache LoUIS API for xscale and feroceon
ARM: mm: update __v7_setup() to the new LoUIS cache maintenance API
ARM: kernel: update __cpu_disable to use cache LoUIS maintenance API
ARM: kernel: update cpu_suspend code to use cache LoUIS operations
ARM: mm: rename jump labels in v7_flush_dcache_all function
ARM: mm: implement LoUIS API for cache maintenance ops
ARM: virt: arch_timers: enable access to physical timers
ARM: virt: Add CONFIG_ARM_VIRT_EXT option
ARM: virt: Add boot-time diagnostics
ARM: virt: Update documentation for hyp mode entry support
ARM: zImage/virt: hyp mode entry support for the zImage loader
ARM: virt: allow the kernel to be entered in HYP mode
ARM: opcodes: add __ERET/__MSR_ELR_HYP instruction encoding
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
From Tony Lindgren:
This branch contains regression fixes for omap4/5 ASoC
audio that were caused by the fact that u-boot stopped
muxing non essential pins.
As omap audio and dmaengine development happens on
these platforms, let's make sure they are usable.
Of course this should have been fixed earlier and
not during the -rc cycle.
* tag 'omap-for-v3.7-rc1/fixes-asoc-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
ARM: OMAP: board-4430-sdp: Pin mux configuration for audio needs
From Tony Lindgren:
This branch contains one counter locking fix and an
alignment fix. Other fixes are warning fixes, fixes
for return value checks.
I've also included removal of some extra semicolons,
dropping of some duplicate includes, and an a change
for wl12xx enumeration that are not strictly fixes
but would be good to get out of the way for -rc1.
* tag 'omap-for-v3.7-rc1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
AM35xx: Add missing hwmod entry for the HDQ/1-Wire present in AM3505/3517 CPUs.
ARM: OMAP2+: gpmc: annotate exit sections properly
ARM: OMAP: fix return value check in realtime_counter_init()
ARM: OMAP: hsmmc: fix return value check in omap_hsmmc_init_one()
OMAPDSS: fix return value check in create_dss_pdev()
ARM: OMAP2+: Add am335x evm and bone targets to common Makefile
arm: increase FORCE_MAX_ZONEORDER for TI AM33XX
ARM: OMAP: OMAP_DEBUG_LEDS needs to select LEDS_CLASS
ARM: OMAP: rx51: Fix a section mismatch warn
ARM: OMAP2+: Round of the carve out memory requested to section_size
ARM: OMAP: counter: add locking to read_persistent_clock
Sometimes we want the kernel build process to only print messages
on errors, e.g. in automated build testing. This uses the "kecho"
macro that the build system provides to hide a few informational
messages. Nothing changes for a regular "make" or "make V=1".
Without this patch, building any ARM kernel results in:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron), McPDM, DMIC, McBSP1 and McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These all use the generic pinctrl-single driver for the padconf registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM and McBSP1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2, McBSP3 and DMIC is not usable on PandaBoard (not connected, no
external pins provided for them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds am335x-evm and am335x-bone dtb targets to
'make dtbs', just like other platforms.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
[wsa: rebased to 3.6-rc7]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into i2c-embedded/for-next
Linux 3.6-rc7
Needed to get updates from i2c-embedded/for-current into i2c-embedded/for-next
This adds simple DT bindings for SDHCI SPEAr controller. It uses cd-gpios
from common mmc bindings.
This also fixes spear300-evb.dts with correct name for card detect binding.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We already have CONFIG_ARCH_MXC cover imx5 and imx6 dtb targets.
Remove the redundant ones with CONFIG_ARCH_IMX5 and CONFIG_SOC_IMX6Q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add board files (vt8500-bv07, wm8505-ref and wm8650-mid)
to allow 'make dtbs' on arch-vt8500.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Unit addresses, whilst written in hex, don't contain a 0x prefix.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions).
PV console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQbJELAAoJEFjIrFwIi8fJSI4H/32qrQKyF5IIkFKHTN9FYDC1
OxEGc4y47DIQpGUd/PgZ/i6h9Iyhj+I6pb4lCevykwgd0j83noepluZlCIcJnTfL
HVXNiRIQKqFhqKdjTANxVM4APup+7Lqrvqj6OZfUuoxaZ3tSTLhabJ/7UXf2+9xy
g2RfZtbSdQ1sukQ/A2MeGQNT79rh7v7PrYQUYSrqytjSjSLPTqRf75HWQ+eapIAH
X3aVz8Tn6nTixZWvZOK7rAaD4awsFxGP6E46oFekB02f4x9nWHJiCZiXwb35lORb
tz9F9td99f6N4fPJ9LgcYTaCPwzVnceZKqE9hGfip4uT+0WrEqDxq8QmBqI5YtI=
=gxJD
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull ADM Xen support from Konrad Rzeszutek Wilk:
Features:
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions). PV
console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
The Xen-unstable hypervisor (so will be 4.3 in a ~6 months), supports
ARMv7 platforms.
The goal in implementing this architecture is to exploit the hardware
as much as possible. That means use as little as possible of PV
operations (so no PV MMU) - and use existing PV drivers for I/Os
(network, block, console, etc). This is similar to how PVHVM guests
operate in X86 platform nowadays - except that on ARM there is no need
for QEMU. The end result is that we share a lot of the generic Xen
drivers and infrastructure.
Details on how to compile/boot/etc are available at this Wiki:
http://wiki.xen.org/wiki/Xen_ARMv7_with_Virtualization_Extensions
and this blog has links to a technical discussion/presentations on the
overall architecture:
http://blog.xen.org/index.php/2012/09/21/xensummit-sessions-new-pvh-virtualisation-mode-for-arm-cortex-a15arm-servers-and-x86/
* tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (21 commits)
xen/xen_initial_domain: check that xen_start_info is initialized
xen: mark xen_init_IRQ __init
xen/Makefile: fix dom-y build
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
...
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull CMA and DMA-mapping updates from Marek Szyprowski:
"This time the pull request is rather small, because the further
redesign patches were not ready on time.
This pull request consists of the patches which extend ARM DMA-mapping
subsystem with support for CPU coherent (ACP) DMA busses. The first
client of the new version is HighBank SATA driver. The second part of
the pull request includes various cleanup for both CMA common code and
ARM DMA-mapping subsystem."
Fix up trivial add-add conflict due to the "dma-coherent" DT property
being added next to the "calxeda,port-phys" property for the Calxeda
AHCI controller.
* 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: Remove unsed var at arm_coherent_iommu_unmap_page
ARM: highbank: add coherent DMA setup
ARM: kill off arch_is_coherent
ARM: add coherent iommu dma ops
ARM: add coherent dma ops
ARM: dma-mapping: Refrain noisy console message
ARM: dma-mapping: Small logical clean up
drivers: dma-contiguous: refactor dma_alloc_from_contiguous()
1) Apply -- and then revert -- the FUA feature. Caused
disk corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=i3EH
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata changes from Jeff Garzik:
"Minor libata updates, nothing notable.
1) Apply -- and then revert -- the FUA feature. Caused disk
corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix warnings when no PCI
[libata] Makefile: Fix build error in sata_highbank
[libata] export ata_dev_set_feature()
libata-core: use ATA_LBA in ata_build_rw_tf()
ata/ahci_platform: Add clock framework support
pata_arasan: add Device Tree probing capability
pata_arasan: Add clk_{un}prepare() support
ata: add platform driver for Calxeda AHCI controller
sata_fsl: add workaround for data length mismatch on freescale V2 controller
ahci: implement aggressive SATA device sleep support
ata: define enum constants for IDENTIFY DEVICE
Revert "libata: enable SATA disk fua detection on default"
[libata] scsi: implement MODE SELECT command
[libata] scsi: support MODE SENSE request for changeable and default parameters
[libata] scsi: Remove unlikely() from FUA check
libata: enable SATA disk fua detection on default
Some highbank DMA masters can support coherent (ACP) or non-coherent DMA.
This sets up dma_map_ops for masters which are configured for coherent DMA.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
From Roland Stigge. Pulling in one bugfix to the lpc32xx DT conversion.
* 'lpc32xx/dts' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: LED fix in PHY3250 DTS file
using device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LDvq
-----END PGP SIGNATURE-----
Merge tag 'devel-dt-arch-timer-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Few late patches to enable arch timer for omap5
using device tree.
* tag 'devel-dt-arch-timer-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP5: Enable arch timer support
ARM: OMAP: Add initialisation for the real-time counter.
Add device nodes for the four instances of dw_mmc controllers in
EXYNOS5250 and enable instance 0 and 2 for the SMDK5250 board.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adjusts the PHY3250 board file to the actual LED configuration
(active high, default-state and trigger configuration).
Signed-off-by: Roland Stigge <stigge@antcom.de>
Given that the xenvm machine is based on vexpress but with an extremely
limited selection of peripherals (the guest is supposed to use virtual
devices instead), add "xen,xenvm" to the list of compatible machines in
mach-vexpress.
Changes in v3:
- add comments to mark fields that are likely to be changed by the
hypervisor.
Changes in v2:
- remove include skeleton;
- use #address-cells = <2> and #size-cells = <2>;
- remove the debug bootargs;
- use memory@80000000 instead of memory;
- remove the ranges and interrupt-map from the motherboard node;
- set the machine compatible to "xen,xenvm-4.2", "xen,xenvm";
- rename the dts file to xenvm-4.2.dts;
- add "xen,xenvm" to the list of compatible DT strings to mach-vexpress.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pawel Moll <pawel.moll@arm.com> (v2m changes)
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
This moves a few of the newly introduced dtb targets to the common
dts/Makefile instead of the per-platform file.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
New drivers:
- pinctrl (dove, kirkwood, mvebu)
- gpio (mvebu)
* 'kirkwood/drivers' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add gpio support in defconfig
arm: mvebu: add DT information for GPIO banks on Armada 370 and XP
arm: mvebu: use GPIO support now that a driver is available
Documentation: add description of DT binding for the gpio-mvebu driver
gpio: introduce gpio-mvebu driver for Marvell SoCs
arm: mvebu: select the pinctrl drivers for Armada 370 and Armada XP platforms
arm: mvebu: split Kconfig options for Armada 370 and XP
ARM: mvebu: adjust Armada XP evaluation board DTS
ARM: mvebu: Add pinctrl support to Armada 370 SoC
ARM: mvebu: Add pinctrl support to Armada XP SoCs
pinctrl: mvebu: add pinctrl driver for Armada XP
pinctrl: mvebu: add pinctrl driver for Armada 370
pinctrl: mvebu: kirkwood pinctrl driver
pinctrl: mvebu: dove pinctrl driver
pinctrl: mvebu: pinctrl driver core
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'kirkwood/addr_decode' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add address decoding controller to the DT
arm: mvebu: add basic address decoding support to Armada 370/XP
arm: plat-orion: make bridge_virt_base non-const to support DT use case
arm: plat-orion: introduce PLAT_ORION_LEGACY hidden config option
arm: plat-orion: use void __iomem pointers for addr-map functions
arm: plat-orion: use void __iomem pointers for time functions
arm: plat-orion: use void __iomem pointers for MPP functions
arm: plat-orion: use void __iomem pointers for UART registration functions
arm: mach-mvebu: use IOMEM() for base address definitions
arm: mach-orion5x: use IOMEM() for base address definitions
arm: mach-mv78xx0: use IOMEM() for base address definitions
arm: mach-kirkwood: use IOMEM() for base address definitions
arm: mach-dove: use IOMEM() for base address definitions
arm: mach-orion5x: use plus instead of or for address definitions
arm: mach-mv78xx0: use plus instead of or for address definitions
arm: mach-kirkwood: use plus instead of or for address definitions
arm: mach-dove: use plus instead of or for address definitions
This branch had quite a few conflicts, in particular with the PCI static
map rework from Rob Herring, and a few other context conflicts due to
changes in Kconfig, etc.
I fixed up conflicts in:
arch/arm/Kconfig
arch/arm/mach-dove/common.c
arch/arm/mach-dove/include/mach/dove.h
arch/arm/mach-kirkwood/common.c
arch/arm/mach-kirkwood/include/mach/kirkwood.h
arch/arm/mach-mv78xx0/common.c
arch/arm/mach-mv78xx0/include/mach/mv78xx0.h
arch/arm/mach-orion5x/common.c
arch/arm/mach-orion5x/include/mach/orion5x.h
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
New bindings:
- iconnect nand and keys
- mv_cesa
- gpio-fan
* 'kirkwood/dt' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Use devicetree to define DNS-32[05] fan
hwmon: Add devicetree bindings to gpio-fan
Crypto: CESA: Add support for DT based instantiation.
ARM: Kirkwood: Describe iconnect nand in DT.
ARM: Kirkwood: Describe iconnect keys in DT.
* 'kirkwood/boards' of git://git.infradead.org/users/jcooper/linux:
ARM: Dove: allow PCI to be disabled
ARM: dove: SolidRun CuBox DT
ARM: dove: add device tree descriptors
ARM: dove: add device tree based machine descriptor
ARM: dove: add crypto engine
ARM: dove: add clock gating control
ARM: dove: unify clock setup
ARM: initial DTS support for km_kirkwood
arm: add documentation describing Marvell families of SoC
ARM: kirkwood: DT descriptor for Seagate FreeAgent Dockstar
ARM: kirkwood: DT board setup for Seagate FreeAgent Dockstar
ARM: Kirkwood: Iomega ix2-200 DT support
Context conflicts in arch/arm/Kconfig and arch/arm/mach-dove/common.c.
The new device trees added to arch/arm/mach-kirkwood/Makefile.boot are
kept and dealt with in a separate changeset, since moving them out to
the new Makefile in this merge commit doesn't work well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM and clkdev fixes from Russell King:
"Two patches for clkdev which resolve the long standing issue that the
devm_* versions were dependent on clkdev, which they shouldn't have
been. Instead, they're dependent on HAVE_CLK instead, which implies
that you're providing clk_get() and clk_put().
A small fix to the ARM decompressor to ensure that the page tables are
properly interpreted by the CPU, and reserve syscall 378 for kcmp (the
checksyscalls.sh script is unfortunately currently broken so arch
maintainers aren't getting notified of new syscalls...)
Lastly, a larger fix for an issue between the common clk subsystem and
smp_twd which causes warnings to be spat out."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: reserve syscall 378 for kcmp
ARM: 7535/1: Reprogram smp_twd based on new common clk framework notifiers
ARM: 7537/1: clk: Fix release in devm_clk_put()
ARM: 7532/1: decompressor: reset SCTLR.TRE for VMSA ARMv7 cores
ARM: 7534/1: clk: Make the managed clk functions generically available
The gpioX aliases are needed so that the driver can use
of_alias_get_id() to get a 0-based number of the GPIO bank, which we
then use to compute the base GPIO of the bank being probed. This is
similar to what gpio-mxs.c is doing.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP evaluation board is based on the MV78460 Armava XP
SoC. Now that we have separate .dtsi files for the three different
SoCs of the Armada XP family, use the appropriate one as include for
the Armada XP evaluation board .dts file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commits adds the necessary device tree information to define the
compatible property for the pinctrl driver instance of Armada 370 SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commits adds the necessary device tree information to define the
compatible property for the pinctrl driver instance of Armada XP SoCs.
Until now, the device tree representation considered the Armada XP as
a single SoC. But in fact, there are three different SoCs in the
Armada XP families, with different number of CPU cores, different
number of Ethernet interfaces... and different number of muxable pins
or functions. We therefore introduce three armada-xp-mv78xx0.dtsi for
the three SoCs of the Armada XP family. The current armada-xp-db.dts
evaluation board uses the MV78460 variant of the SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove more board-specific code by using devicetree to define the fan
attached to both boards.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on work by Michael Walle and Jason Cooper.
Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/mach-kirkwood/board-dt.c
Define the nand and its partitions in DT and remove them from cmdline
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Define the 2 keys found on iconnect in DT. It's also changing the keycodes/
switches to use better ones.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Misc SoC-related fixes/cleanups for Samsung platforms
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
+ sync to 3.6-rc6
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds basic support for the SolidRun CuBox to DT based
mach-dove. There are still some issues related to ongoing orion/mvebu
development, e.g. gpio-led will not work as there is no DT pinctrl
for dove yet and we don't have board specific setup code. Nevertheless,
the DT description is already introduced here.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds device tree decriptors for dove SoC and currently
supported boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a first attempt to support the km_kirkwood reference design with
a device tree. This km_kirkwood design is present in many Keymile
products. It is based on the Marvell Bobcat SOC which integrates a
Kirkwood CPU next to a big L2 Ethernet Switch. The Kirkwood in the SOC
is very similar to the "normal" one, but there are a few differences.
This initial support is minimal: the kernel can boot with network
(ge0), serial port and NAND functional.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds the corresponding device tree descriptor for the
Seagate FreeAgent Dockstar based on Kirkwood DT.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since the dtb targets have moved to arch/arm/boot/dts/Makefile, sweep
the platforms that have had new targets added recently and move them over.
While I was at it, I also made the dtb generation more generic, i.e. if
the platform is enabled then all dtbs for that platform will be created.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brown <davidb@codeaurora.com>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQU4miAAoJEMhvYp4jgsXi1vMH/A4JJXe24cyo31rHJspZDSFg
nnCbnGKfDEOIHwLA8C3OeJuhswMlP/vWlGC512QXL8903XpZ2VJe63f2CLo1mN7Z
hg3JPWrp2VXZ/bqdMnUcw2CtlylrhyG9MUPapkcp+5Agjz2lwaJtRNL6LRRQX4Ei
cWjsJtaFpRj1QraFna0hpTQNO640je6s1rAIJl6eNOuX08l12ZAGDUA+IUUsa1cA
0OGeOAjH6gmkpMI89j1VPPKVRLHIdP4QcxmAZCHJ2LtvylyrlmYskctpAYibobvt
JPLnZgzMFAegnWtJhOYodhBJlfyypEeh2fsZVyDPowqRz9vaAWRjs6u/I4GYaME=
=HR3H
-----END PGP SIGNATURE-----
Merge tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
* next/soc: (50 commits)
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
ARM: tegra30: add CPU hotplug support
ARM: tegra: clean up the common assembly macros into sleep.h
ARM: tegra: replace the CPU CAR access code by tegra_cpu_car_ops
ARM: tegra: introduce tegra_cpu_car_ops structures
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: AM33XX: clock: Add dcan clock aliases for device-tree
ARM: OMAP2+: dpll: Add missing soc_is_am33xx() check for common functions
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
ARM: OMAP3+: hwmod: Add AM33XX HWMOD data
ARM: OMAP2+: hwmod: Hook-up am33xx support in omap_hwmod framework
...
Change/remove conflict in arch/arm/mach-ux500/clock.c resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
and imx-dt-3.7 and imx-clk-dt-lookup which have already been pulled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQW8LwAAoJEFBXWFqHsHzOtVgIAJN8Y2vHgI4kqMmMlXW8QhGj
7YNdFiWlLdhJL9jMOw2v8GwacUZ6x9HsgdK0h6DW3jERi54P7iafdsiFjRH2x8CI
PBNT8Qk9wyZnLNHq1bEUQIg7Nra1aZY9btEzqq0tpRYeJ9PMrgWOrI0ndQiSkTK7
xiYmJATBeQWFPUCGKUDtb9wuDLQ0gQSe1aE0zRkKoIgMn8/cKrbHO1TXh50QC4rt
hie0TkkCvPqeBGae6CTBd0AHFglNMCprwXIsHnnsmPrQdUZCLg9Eum+SDNRR2g19
g3COd+ecUfxtZpsJjdj/iV078nRPqg4GNCj3KO4dgmzHOe72Aed0xNcHNiTJoC0=
=5dum
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.7-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
This is the second round of imx-dt patches for 3.7. It's based on
and imx-dt-3.7 and imx-clk-dt-lookup which have already been pulled.
* tag 'imx-dt-3.7-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: use pll2_pfd2_396m as the enfc_sel's parent
ARM: dts: imx6q-sabrelite: add usbotg pinctrl support
ARM: dts: imx6q-sabrelite: add usbmisc device
mxs-dt-3.7 and mxs-clk-dt-lookup which have been pulled into arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQW8PHAAoJEFBXWFqHsHzO4GYH/jMaG4hFP4Epmxo88WJGhU4l
6ZNI1Gz90XGnx+EKJY7B30cRkvO/ydWrlUB0lMMnKdXuM/okAV66TFWrNTaEWjq1
15xlfn7jlpxY2lu2zflw3sM00jAL65AJDG3G4hA+ZnQlRo4G5MHYHAAGUawwxBJl
J0P0ZSGrVvZ82wGnW2FhvjrF0WR6Ni0mrhRnWQhsub9lykc4YUgOhG0IgxAh8jMx
RW7cR1o4St8ro4vm4joJdEa+ZQDprQDQsMJBOkacTb3SH4uDNpJpSeFVXa7BMSZ+
A8UpG+aHELyCJKU3gHuApcxS0tiK+vd1p0dikRGu6y167hHcKkzqZyVqOYTMrOU=
=/jro
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.7-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
This is the second round of mxs-dt patches for 3.7. It's based on
mxs-dt-3.7 and mxs-clk-dt-lookup which have been pulled into arm-soc.
* tag 'mxs-dt-3.7-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: m28evk: Disable OCOTP OUI loading
ARM: dts: imx23-olinuxino: Add USB host support
ARM: dts: mx23: Add USB resources
ARM: dts: mxs: Add ethernetX to macX aliases
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
On Harmony, LDO7 does not feed vdd_fuse. Correct the regulator name.
This issue was probably the result of copying Ventana's regulator setup
when creating the Harmony .dts file. No other naming issues appear to
exist.
Reported-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On board keys on Origen board can serve as wakeup sources,
hence they are marked accordingly in the device tree file.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This commit adds basic device tree for Exynos4210-based Trats board.
Currently it provides support for eMMC over sdhci and MAX8997 PMIC.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently all boards must explicitly disable all unused device tree
nodes of unused components (e.g. i2c, sdhci, etc...). This makes it
necessary to all boards to be aware of all components on the SoC, which
in turns makes board dts files longer and more difficult to maintain
(e.g. adding new components to SoC-level tree requires adding nodes with
status="disabled" to every board).
This patch changes "status" of all optional components in SoC-level dts
file to "disabled", adds status="okay" to respective nodes of used
components in dts of all boards and removes all nodes with only
status="disabled" from boards dts.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Most definitions from exynos4210.dtsi can be applied for other SoCs from
EXYNOS4 line as well, so move the common part into separate file that
can be included by dtsi files of other EXYNOS4 SoCs (as well as current
exynos4210.dtsi).
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: Dongjin Kim <dongjin.kim@agreeyamobility.net>
submitted a similar patch 'Add DTS files derived from common EXYNOS4'
before this but I picked this up because of included exynos4x12 stuff]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This branch includes some late device tree changes for Tegra:
A property is added to Whistler's device tree to enable the PMIC to
act as the pm_power_off() implementation.
A number of new device tree are added for boards from Avionic Design.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=s7Ln
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
ARM: tegra: second round of device tree changes
This branch includes some late device tree changes for Tegra:
A property is added to Whistler's device tree to enable the PMIC to
act as the pm_power_off() implementation.
A number of new device tree are added for boards from Avionic Design.
* tag 'tegra-for-3.7-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: dt: tegra: whistler: configure power off
From Kukjin Kim:
This is for updating non-DT Samsung board files for v3.7, there are adding
generic PWM lookup support and some updates.
* 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add generic PWM lookup support for SMDKV310
ARM: EXYNOS: Add generic PWM lookup support for SMDK4X12
ARM: EXYNOS: Use generic pwm driver in Origen board
ARM: dts: Add heartbeat gpio-leds support to Origen
ARM: dts: Use active low flag for gpio-keys on Origen
ARM: S3C64XX: Register audio platform devices for Bells on Cragganmore
ARM: S3C64XX: Update configuration for WM5102 module on Cragganmore
Fixed trivial merge conflict in arch/arm/mach-exynos/mach-smdkv310.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is G-Scaler DT for supporting EXYNOS5 SoCs.
* 'next/dt-gscaler' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
From Kukjin Kim:
This branch is for supporting pinctrl for Samsung EXYNOS. Now this can
support EXYNOS4210 and other EXYNOS SoCs such as EXYNOS4X12 will be
supported next time.
* 'next/pinctrl-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
gpio: exynos4: skip gpiolib registration if pinctrl driver is used
pinctrl: add exynos4210 specific extensions for samsung pinctrl driver
pinctrl: add samsung pinctrl and gpiolib driver
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQVlRgAAoJEBvUPslcq6VzbSwP/RNdw33WTv7slY8v2x9C+jfe
fzpJltqtWf1xLQ5ixAMwzBxc4/I+m/fz3ZhxG15amqD1sQuwDNNVwI6D5F4pIH4K
ZfyaeA8jteH487f7PxMlurtVYgPRqLrMXBahxKgcM6WwJ0tFspGuXQeKMhjhRnYJ
4+0GQ/R60UmexyAF4Ish4YfVfe0Iy8deVuGjOO7xIdsKrC1uymXbT7HB0o7Tz4tj
btsEUXs4UMCh2VoYzqVxaP1uMumOnuVOFOuWjcNOni3TMdjmllPpoApsXE27rNKC
0D/MzCyutFEO7q7/8TSUs3TOy+my18Z6Fz9hEkw7fUOOXQ3iUDqI79FbvMv9mWe+
nW2BFZZCeuTqErGNakgluGtasLOfvqOqzSO7U68XGgHp86G42N2EDs4raTDAeKTN
YXzLSiPYvV5QOUFbP5uagiKFcFUbcfNYZytTPwZ8hBk4hXtDmwqhSEgzxhAKGtgx
y0ljt3iQNxk3EVhIv7oi0FxCFX2ioikYPTOlHkpvNwkXa7ruvvU1CudIGSdZ/Nn3
SoEkRDwx6CpA37aAusfWioYKWhrctfDBl9Nt0IXwZy1b0MO1QIUaL0RY3Y5FsES+
25MP+5Ns6nkmzzTs72Gu+W9bL6E3eHAkAoaDb9JPH2Jix8vXRMgIISyu9Fzze504
ypeFe5TtLc/uYkviZhi6
=fzT6
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
The Medcom is a 16:9 15" terminal that is used for patient infotainment
in hospitals.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Plutux is a set-top box device based on the Tamonten SOM and can be
connected to a display via HDMI.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tamonten is an NVIDIA Tegra2 based system-on-module (SOM) that is
designed to cover a broad range of applications.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
PWM devices can be referenced in the DT by phandle and per-chip index.
In order for this to work properly, the PWM controller needs to have a
label attached to it.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
SSP won't probe unless the specified register address format
is correct i.e. we have to specify that the address is in hex.
After this patch has been applied, the SSP (SPI) driver probes
as expected.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch ensures the tc3589x and tc3598x-gpio devices are
rightfully given interrupt controller status. We also describe
the tc3598x-gpio GPIO expander in full and specify it as a GPIO
controller. Finally we reference that the external MMC slot's
Card Detection GPIO on the HREF is located on the tc3598x-gpio
expander.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This property has no place here as the populated node is not related
to a GPIO controller.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is where we link together all of the SoC sound components for
a given platform. This all encompassing sound node is only found
in the very lowest hierarchical DTS file, since the component mix may
well change from board variant to board variant.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch enables the two important MSP devices for ST-Ericsson's
hardware reference development board.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the skeleton nodes for each of the known I2C sub-devices
currently registered on ST-Ericsson's HREF Development Platform. We
will fill these nodes in turn as the drivers are enabled for Device
Tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is where we link together all of the SoC sound components for
a given platform. This all encompassing sound node is only found
in the very lowest hierarchical DTS file, since the component mix may
well change from board variant to board variant.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch inserts all known MSP devices into the DBx5x0 Device Tree
disabled and enables the two important ones for the Snowball low-cost
development board.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Ensure correct probing and pass though important configuration
options to the AB8500 CODEC driver when DT is enabled
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add three nodes enabling UART support on the HREF hardware
reference board.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
First commit applying the new Device Tree for ST-Ericsson's u8500
based hardware reference board.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since initial support was provided for the Nomadik I2C driver, it
has been converted to an AMBA device. AMBA devices are probed in
a slightly different way to other devices, so we have to identify
them using an "arm,primecell" compatible string. As well as doing
just that, this patch specifies which regulators the controller
should use and requests a clock-speed. The latter is provided as
more of an example, as it's the same as the recently changed
default configuration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The compatible string found in the Power-On-Key's MFD cell matches
the device name provided in the driver. Keeping this naming convention
seems like a good idea, so we're changing the one found in the DTS
file to match.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's understood that the AB8500 should be subordinate to the DB8500;
however, the AB8500 uses the GIC as it's interrupt controller. If
we do not specify which IRQ controller to use the default is to use
the next encountered IRQ controller as we climb the tree. This would
be the DB8500. This patch ensures the AB8500 makes use of the correct
interrupt controller.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We're just about to provide the DB8500-PRCMU with its own IRQ domain,
so that its subordinate drivers can use it as an interrupt controller.
It's obligatory for all IRQ controllers to reference themselves as
such from its own node in Device Tree. This patch does just that.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Modified UART DT node to use a unit-address to create unique UART node
names, rather than using non-type names "uart0" and "uart1".
Note that UART 1 (the Broadcom "mini UART") is not yet present, but
I'm naming the DT node in anticipation that it will be added.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The System Timer peripheral provides four 32-bit timer channels and a
single 64-bit free running counter. Each channel has an output compare
register, which is compared against the 32 least significant bits of the
free running counter values, and generates an interrupt.
Timer 3 is used as the Linux timer.
The BCM2835 also contains an SP804-based timer module. However, it
apparently has significant differences from the standard SP804 IP block,
and Broadcom's documentation recommends using the system timer instead.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved to drivers/clocksource/. This looks like the desired location for
such code now.
* Added DT binding docs.
* Moved struct sys_timer bcm2835_timer into time.c to encapsulate it more.
* Simplified bcm2835_time_init() to find one matching node and operate on
it, rather than looping over all matching nodes. This seems more
consistent with other clocksource code.
* Simplified bcm2835_time_init() using of_iomap().
* Renamed struct bcm2835_timer.index to match_mask to better represent its
purpose.
* s/printk(PR_INFO/pr_info(/
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
the size of the hwirq space, and pass the total size of the hwirq space
to irq_domain_add_linear(), rather than just the number of valid hwirqs;
the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
rather than nesting it inside a /axi node. Hence, changed the reg value
since /axi had a ranges property. This seems simpler to me, but I'm not
sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
removing the need to patch include/linux/irqdomain.h or
kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC.
http://www.broadcom.com/products/BCM2835http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Note that the documentation in the latter .pdf assumes the MMU setup
that's used on the "VideoCore" companion processor, and does not document
physical peripheral addresses. Subtract 0x5e000000 to obtain the physical
addresses. This is accounted for by the ranges property in the /soc node
in the device tree.
The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a
minimal device tree for this board; enough to see some very early kernel
boot messages through earlyprintk. However, this patch does not yet
provide a useful booting system.
http://www.raspberrypi.org/.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split from 3-4 months ago, and significantly stripped down and
modified since.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add DT property to tell the MAX8907 that it should provide the
pm_power_off() implementation. This allows "shutdown" to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The zImage loader needs to turn on the MMU in order to take
advantage of caching while decompressing the zImage. Running this
in hyp mode would require the LPAE pagetable format to be
supported; to avoid this complexity, this patch switches out of hyp
mode, and returns back to hyp mode just before booting the kernel.
This implementation assumes that the Hyp mode view of memory and the
PL1 view of memory are coherent, providing that the MMU and caches
are off in both, as required by the boot protocol. The zImage
decompression code must drain the write buffer on completion anyway, and
entry into Hyp mode should flush any prefetch buffer, avoiding hazards
associated with local write buffers and the pipeline.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enable Cortex A15 generic timer support for OMAP5 based SOCs.
The CPU local timers run on the free running real time counter clock.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQWC9nAAoJEAf03oE53VmQV1QIAJ9zbpXxtPQytJjNR8Md9XEK
Y5Ao2xzjZu4ZawQCyr3cnYvup7hMxfTK6Fij5lWwnwGech4tqfkoIuvL2soiLJfG
4ioznzC3CN6rNZZTJo9RHIVouEADfqX6pShLPttau34RCDpZqiyuekcav8slBiCo
/lOgsZWVOkjpjvvino4w0EdUjyz5jWT0IFcDxoVhnJGsdHunkXwASu8OeYk9kWSJ
KbWERMeruGssz9ch6rccIvaYV7pL+WM2Rm8PDNHzvziKaXRD8Sod6qZJpj7mp9XJ
9gAujzss7sZ65T1P3vVEqYbWFAZjYzUdFcj9G075kSlZysA8rthZVXfym+xg/G0=
=7hqG
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
Modify AT91 device tree files for making the GPIO interrupts work.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fix missing #interrupt-cells on gpio-controller
This moves the physmap flash and SMSC91x ethernet devices
over to the device tree, moving the static board code down
into the #ifndef CONFIG_OF section.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts the AMBA (PrimeCell) devices on the Integrator/AP
and Integrator/CP over to probing from the Device Tree if the
kernel is compiled for Device Tree support.
We continue to #ifdef out all non-DT code and vice versa on
respective boot type to get a clean cut.
We need to add a bunch of auxdata (compare to the Versatile)
to handle bus names and callbacks alike.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is initial device tree support for the ARM Integrator family,
we create a very basic device tree, #ifdef out the non-DT machines
when compiling for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using syscon to access anatop register.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Include headfile for easy using.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- add usbmisc device
- set property fsl,usbmisc for usb controllers
- set disable-over-current for imx6q-sabrelite usb otg
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It replaces the clk_register_clkdev in imx6q clock driver with DT
lookup. It depends on Mike's clk-3.7 branch.
When it gets merged together with imx-dt-3.7, there is a trivial
conflict on arch/arm/boot/dts/imx6q.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQTyFwAAoJEFBXWFqHsHzOcXkH/1a2RX8pUMsYHS5efpGaRUjJ
7PKKbAuMuGAgqdRDv1t2dcXuUv3zJgY/sdrivD9iwMqVSsQDW9MrdKyvBXg9m5UL
rg1Uc8r6mJlHSljimN8hoHp4PGFF7DCVls5y+3jsk/I2tWK+S/w00iP/aOFgkJNc
9Bg0ZhofKGOGpYK5joaBYAqvVM7F92gjpX+PytNEkJHGRKxCEsTRq4DRR3+r3uqs
GuoHOflYMEmviKYaZ/I14rwUJWFF4vIxuFC4vT88erpj3Fs0y7XkEWJiKU/2ma6M
w86qOUI6nU0iW5AILu3IvjSEvh2h/ZZ+5y3lVvzghcKK2QP4d4bEWnC745NRVSI=
=pxVx
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-dt-lookup' into imx/dt-for-3.7-2
Conflicts:
arch/arm/boot/dts/imx6q.dtsi
Add ethernet0 and ethernet1 aliases into the imx28.dtsi file, as
that is what most bootloaders use to pass MAC address. The bootloader
seeks for this alias and adds "mac-address" and "local-mac-address"
properties to the aliased node. This fixes issues with FEC having
NULL MAC address when update_fec_mac_prop() wasn't called. And
not all boards call update_fec_mac_prop() .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Remove all board files and make mach-mxs a DT-only platform
- Some dts file formatting and style fixing
- DTS update for additional boards and devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQTqwnAAoJEFBXWFqHsHzOnr8H/A5PxxGIjgWc6LmPHVbZ9pIr
RcRvKz6/jPvDK3Opf1VzYHuOKY1/pnyjbt39rhRLEu3gSki5eJMcao9mY06unj2G
9DfmzDAVKB+ZYa/2Mo7uAvAO9HUjS5egLY1kulYvjqlPnx8FgZekUDYdmbTwKrpt
e2/rB301okFeAEp/8WdVdHpZJ8SDhMyCxxMJ3jGdRshwXnFi/zUTrz8q1xdINhzU
qna4EYhnQGd3nLnupBBf5TWPcOb0x37Td8PU1/q2eHCR5KP267Rhl+jMjYTnEGOo
NMfHcLGaUYhZSieM05s9M6g4mB1fjshqVZDOZtMooT0+6YHOKqB6V8gLxrnXyTY=
=YTWA
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.7' into mxs/dt-for-3.7-2
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=utuw
-----END PGP SIGNATURE-----
Merge tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
This branch adds two main features to Tegra boards, simply by amending
device tree files: regulator support and the ability to turn off system
power when executing "shutdown".
As part of these changes, the board file for Cardhu is split into two
versions, since different revisions have different hardware in some
areas, especially related to regulators.
This branch is based on v3.6-rc4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=MSSD
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
This branch adds two main features to Tegra boards, simply by amending
device tree files: regulator support and the ability to turn off system
power when executing "shutdown".
As part of these changes, the board file for Cardhu is split into two
versions, since different revisions have different hardware in some
areas, especially related to regulators.
* tag 'tegra-for-3.7-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: configure power off for some boards
ARM: dt: tegra: whistler: add regulators
ARM: dt: tegra: paz00: add regulators
ARM: dt: tegra: ventana: add regulators
ARM: dt: tegra: seaboard: add regulators
ARM: tegra: cardhu: add dt entry for fixed regulators
ARM: dt: tegra: cardhu: split dts file for support multiple board versions
ARM: dt: tegra: cardhu: add entry for PMIC TPS65911.
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6+9B
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch removes all remaining board files for Tegra; booting is
now through device tree only.
Related, the Harmony DT is augmented with regulators, since this allows
removal of board-harmony-power.c; no other boards had regulator support.
This change depends on an enhancement to the TPS6586x regulator driver,
hence the dependency mentioned below.
This branch is based on v3.6-rc4, followed by a merge of
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git tps6589x-dt
This branch is a dependency the cleanup2 branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=bA1h
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-board-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: remove board files
This branch removes all remaining board files for Tegra; booting is
now through device tree only.
Related, the Harmony DT is augmented with regulators, since this allows
removal of board-harmony-power.c; no other boards had regulator support.
This change depends on an enhancement to the TPS6586x regulator driver,
hence the dependency mentioned below.
* tag 'tegra-for-3.7-board-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: harmony: configure power off
ARM: dt: tegra: harmony: add regulators
ARM: tegra: remove board (but not DT) support for Harmony
ARM: tegra: remove board (but not DT) support for Paz00
ARM: tegra: remove board (but not DT) support for TrimSlice
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=KXPz
-----END PGP SIGNATURE-----
Merge tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/dt
From David Brown:
These patches migrate both the 8660 and 8960 targets on msm to be
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
By Stephen Boyd
via David Brown
* tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Remove non-DT targets from 8960
ARM: msm: Add DT support for 8960
ARM: msm: Move io mapping prototypes to common.h
ARM: msm: Rename board-msm8x60 to signify its DT only status
ARM: msm: Make 8660 a DT only target
ARM: msm: Move 8660 to DT timer
ARM: msm: Add DT support to msm_timer
ARM: msm: Allow timer.c to compile on multiple targets
ARM: msm: Don't touch GIC registers outside of GIC code
ARM: msm: Add msm8660-surf.dts to Makefile.boot
ARM: msm: Add handle_irq handler for 8660 DT machine
Resolved trivial context conflict in arch/arm/mach-msm/io.c and a
remove/change conflict in arch/arm/mach-msm/board-msm8x60.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GLSh
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparseirq-for-v3.7' into devel-dt
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
Conflicts:
arch/arm/mach-omap2/omap4-common.c
drivers/gpio/gpio-twl4030.c
This patch zeroes the SCTLR.TRE bit prior to setting the mapping as
cacheable for ARMv7 cores in the decompressor, ensuring that the
memory region attributes are obtained from the C and B bits, not from
the page tables.
Cc: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DT property to tell the TPS6586x that it should provide the
pm_power_off() implementation. This allows "shutdown" to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Harmony uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.
Based on Ventana regulator patch by Stephen Warren <swarren@nvidia.com>
and converted to Harmony.
swarren made the following changes:
* Added ldo0 regulator configuration to device tree, and updated
board-harmony-pcie.c for the new regulator name.
* Fixed vdd_1v05's voltage from 10.5V to 1.05V.
* Modified board-harmony-pcie.c to obtain the en_vdd_1v05 GPIO number at
run-time from device tree instead of hard-coding it.
* Removed board-harmony{-power.c,.h} now that they're unused.
* Disabled vdd_1v05 regulator; the code in board-harmony-pcie.c hijacks
this GPIO for now. This will be fixed when the PCIe driver is re-
written as a driver. The code can't regulator_get("vdd_1v05") right
now, because the vdd_1v05 regulator's probe gets deferred due to its
supply being the PMIC, which gets probed after the regulator the first
time around, and this dependency is only resolved by repeated probing,
which happens when deferred_probe_initcall() is called, which happens
in a late initcall, whose runtime order relative to harmony_pcie_init()
is undefined, since that's also called from a late initcall.
* Removed unused harmony_pcie_initcall().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This lets us build a multiplatform kernel for experimental purposes.
However, it will not be useful for any real work, because it relies
on a number of useful things to be disabled for now:
* SMP support must be turned off because of conflicting symbols.
Marc Zyngier has proposed a solution by adding a new SOC
operations structure to hold indirect function pointers
for these, but that work is currently stalled
* We turn on SPARSE_IRQ unconditionally, which is not supported
on most platforms. Each of them is currently in a different
state, but most are being worked on.
* A common clock framework is in place since v3.4 but not yet
being used. Work on this is on its way.
* DEBUG_LL for early debugging is currently disabled.
* THUMB2_KERNEL does not work with allyesconfig because the
kernel gets too big
[Rob Herring]: Rebased to not be dependent on the mass mach header rename.
As a result, omap2plus, imx, mxs and ux500 are not converted. Highbank,
picoxcell, mvebu, and socfpga are converted.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
In preparation to support multi-platform kernels, move all the dtb targets
out of the mach Makefile.boot and into the arch/arm/boot/dts/Makefile
which is closer to the sources.
DTBs are only built when CONFIG_OF is enabled and now use top level
CONFIG_ARCH_xxx instead of chip or board specific config options.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Add basic support to boot 8960 with device tree. For now just
support a basic machine with a uart device.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[davidb@codeaurora.org: Remove leading zeros]
Signed-off-by: David Brown <davidb@codeaurora.org>
