The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.
Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Fix autoloading of fschmd on recent Fujitsu machines
hwmon: (coretemp) Properly label the sensors
hwmon: (coretemp) Skip duplicate CPU entries
hwmon: (it87) Fix in7 on IT8720F
hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c/mips: Fix error return codes from Sibyte i2c bus driver
i2c: Fix probability check
Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
spi_t was removed in commit 644b2a680c
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.
Fixes the following build issue:
CC arch/powerpc/sysdev/micropatch.o
micropatch.c: In function 'cpm_load_patch':
micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
micropatch.c:629: error: 'spp' undeclared (first use in this function)
micropatch.c:629: error: (Each undeclared identifier is reported only once
micropatch.c:629: error: for each function it appears in.)
Reported-by: LEROY Christophe <christophe.leroy@c-s.fr>
Reported-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sibyte i2c bus driver returns non-descriptive error values.
Update to return error values as defined in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new unified probing function differs from the original code, and
the preliminary test whether probing is possible must be updated
accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.
This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sergey Spiridonov <sena@hurd.homeunix.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.
It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Cc: stable@kernel.org
Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.
Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)
Current kernel reports
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +74.0 C
Core0 Temp: +70.0 C
Core1 Temp: +69.0 C
Core1 Temp: +70.0 C
With this patch I have
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +54.0 C
Core0 Temp: +51.0 C
Core1 Temp: +48.0 C
Core1 Temp: +49.0 C
Cc: stable@kernel.org [.32.x .33.x, .34.x]
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode. This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Calling g_fmt before s_fmt resulted in a NULL pointer dereference as no
default formats were being selected on probe.
Reported-by: Németh Márton <nm127@freemail.hu>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Issuing a GET_MIN request on the power line frequency control times out
on at least the Apple iSight. As the UVC specification doesn't list
GET_MIN/MAX/RES as supported on that control, remove them from the
uvc_ctrls array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a short delay when stopping the decoder, allowing it to settle and
preventing some unexpected interaction with other firmware commands.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Tested-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge EEPROM tuner code 168 has recently shown up on HVR-1600 TV
capture cards supported by the cx18 driver. This change allows analog
tuner type autodetection to succeed for these cards.
Information for decoding tuner code 168 was provided by Hauppauge.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Actually OMAP doesn't support scatter-gather DMA for
Display subsystem but due to legacy coding it has been overlooked
till now.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes -
- Kconfig option dependancy changed to ARCH_OMAP2/3 from
ARCH_OMAP24XX/34XX
- There are some moments of function from omap_dss_device
to omap_dss_driver. Incorporated changes for the same.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix world-writable child interface control sysfs attributes
IB/qib: Clean up properly if qib_init() fails
IB/qib: Completion queue callback needs to be single threaded
IB/qib: Update 7322 serdes tables
IB/qib: Clear 6120 hardware error register
IB/qib: Clear eager buffer memory for each new process
IB/qib: Mask hardware error during link reset
IB/qib: Don't mark VL15 bufs as WC to avoid a rare 7322 chip problem
RDMA/cxgb4: Derive smac_idx from port viid
RDMA/cxgb4: Avoid false GTS CIDX_INC overflows
RDMA/cxgb4: Don't call abort_connection() for active connect failures
RDMA/cxgb4: Use the DMA state API instead of the pci equivalents
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (35 commits)
NET: SB1250: Initialize .owner
vxge: show startup message with KERN_INFO
ll_temac: Fix missing iounmaps
bridge: Clear IPCB before possible entry into IP stack
bridge br_multicast: BUG: unable to handle kernel NULL pointer dereference
net: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined
net/ne: fix memory leak in ne_drv_probe()
xfrm: fix xfrm by MARK logic
virtio_net: fix oom handling on tx
virtio_net: do not reschedule rx refill forever
s2io: resolve statistics issues
linux/net.h: fix kernel-doc warnings
net: decreasing real_num_tx_queues needs to flush qdisc
sched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock
qlge: fix a eeh handler to not add a pending timer
qlge: Replacing add_timer() to mod_timer()
usbnet: Set parent device early for netdev_printk()
net: Revert "rndis_host: Poll status channel before control channel"
netfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT
drivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h
...
Then it will first check x86_platforms's i8042 detection result,
then go on with normal probe.
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <4c34dd482753bb8f1@agluck-desktop.sc.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This reverts commit 0b28bac5ae.
After adding x86_platform's detection for i8042 controller, we
don't need the force dependency on !X86_MRST any more
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <1278342202-10973-5-git-send-email-feng.tang@intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This reverts commit 685afae025.
After adding x86_platform's detection for i8042 controller, we
don't need the force dependency on !X86_MRST any more
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <1278342202-10973-4-git-send-email-feng.tang@intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The original KERN_CRIT will mess up terminals.
CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: correctly update connector DPMS status in drm_fb_helper
drm/radeon/kms: fix shared ddc handling
drm/ttm: Allocate the page pool manager in the heap.
We don't currently update the DPMS status of the connector (both in the
connector itself and the connector's DPMS property) in the fb helper
code. This means that if the kernel FB core has blanked the screen,
sysfs will still show a DPMS status of "on". It also means that when X
starts, it will try to light up the connectors, but the drm_crtc_helper
code will ignore the DPMS change since according to the connector, the
DPMS status is already on.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28436 (the annoying
"my screen was blanked when I started X and now it won't light up" bug).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connectors with a shared ddc line can be connected to different
encoders.
Reported by Pasi Kärkkäinen <pasik@iki.fi> on dri-devel
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When battery is hot-added, we should not invoke power_supply_changed
in acpi_battery_notify, because it has been invoked in acpi_battery_update,
and battery->bat.changed_work is queued in keventd already.
https://bugzilla.kernel.org/show_bug.cgi?id=16244
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@sude.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Repeated ttm_page_alloc_init/fini fails noisily because the pool
manager kobj isn't zeroed out between uses (we could do just that but
statically allocated kobjects are generally considered a bad thing).
Move it to kzalloc'ed memory.
Note that this patch drops the refcounting behavior of the pool
allocator init/fini functions: it would have led to a race condition
in its current form, and anyway it was never exploited.
This fixes a regression with reloading kms modules at runtime, since
page allocator was introduced.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sumeet Lahorani <sumeet.lahorani@oracle.com> reported that the IPoIB
child entries are world-writable; however we don't want ordinary users
to be able to create and destroy child interfaces, so fix them to be
writable only by root.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If qib_init() fails, the driver fails to free memory, unregister
device files, and unregister with the PCIe framework. The driver will
unload without error but a subsequent driver load will cause the
system to panic. This was found by changing the 7220 code to load the
serdes microcode separately and not installing the microcode file.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Workqueues aren't exactly equivalent to tasklets since the callback
function may be called from multiple CPUs before the callback returns.
This causes completion notification callbacks to have MT bugs since
they weren't expecting this behavior. The fix is to use a single
threaded work queue.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware error register needs to be cleared or another interrupt
will be generated, thus causing an infinite loop. This is a
regression introduced when removing debug output.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The eager buffers are not being cleared before being mmapped into a
new user address space. This is a potential security risk and should
be fixed. Note that the eager header queue is already being cleared.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HCA checks for certain hardware errors which can be falsely
triggered when the IB link is reset. The fix is to mask them rather
than report them.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't set write combining via PAT on the VL15 buffers to avoid a rare
problem with unaligned writes from interrupt-flushed store buffers.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The T4 IQ hw design assumes CIDX_INC credits will be returned on a
regular basis and always before the CIDX counter crosses over the PIDX
counter. For RDMA CQs, however, returning CIDX_INC credits is only
needed and desired when and if the CQ is armed for notification. This
can lead to a GTS write returning credits that causes the HW to reject
the credit update because it causes CIDX to pass PIDX. Once this
happens, the CIDX/PIDX counters get out of whack and an application
can miss a notification and get stuck blocked awaiting a notification.
To avoid this, we allocate the HW IQ 2x times the requested size.
This seems to avoid the false overflow failures. If we see more
issues with this, then we'll have to add code in the poll path to
return credits periodically like when the amount reaches 1/2 the queue
depth). I would like to avoid this as it adds a PCI write transaction
for applications that never arm the CQ (like most MPIs).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.
No functional change.
For further information about the background:
http://marc.info/?l=linux-netdev&m=127037540020276&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
net_device allocated with alloc_eip_netdev() must be freed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some machines (currently only the Toshiba Tecra A11 is known), the GPU
locks up when modeset is forced on LID open. This patch adds a new DMI
blacklist and omits modesetting for all matches.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15550
Signed-off-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The "present" flag was initialized too late -- possibly, a card
was already registered at this time, so re-setting the flag to 0
caused pcmcia_dev_present() to fail.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6205/1: perf: ensure counter delta is treated as unsigned
ARM: 6202/1: Do not ARM_DMA_MEM_BUFFERABLE on RealView boards with L210/L220
ARM: 6201/1: RealView: Do not use outer_sync() on ARM11MPCore boards with L220
ARM: 6195/1: OMAP3: pmu: make CPU_HAS_PMU dependent on OMAP3_EMU
ARM: 6194/1: change definition of cpu_relax() for ARM11MPCore
ARM: 6193/1: RealView: Align the machine_desc.phys_io to 1MB section
ARM: 6192/1: VExpress: Align the machine_desc.phys_io to 1MB section
ARM: 6188/1: Add a config option for the ARM11MPCore DMA cache maintenance workaround
ARM: 6187/1: The v6_dma_inv_range() function must preserve data on SMP
ARM: 6186/1: Avoid the CONSISTENT_DMA_SIZE warning on noMMU builds
ARM: mx3: mx31lilly: fix build error for !CONFIG_USB_ULPI
[ARM] mmp: fix build failure due to IRQ_PMU depends on ARCH_PXA
[ARM] pxa/mioa701: fix camera regression
[ARM] pxa/z2: fix flash layout to final version
[ARM] pxa/z2: fix missing include in battery driver
[ARM] pxa: fix incorrect gpio type in udc_pxa2xx.h
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core:
MAINTAINERS: Add an entry for i7core_edac
i7core_edac: Avoid doing multiple probes for the same card
i7core_edac: Properly discover the first QPI device
virtio net will never try to overflow the TX ring, so the only reason
add_buf may fail is out of memory. Thus, we can not stop the
device until some request completes - there's no guarantee anything
at all is outstanding.
Make the error message clearer as well: error here does not
indicate queue full.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY)
Cc: stable@kernel.org # .34.x (s/virtqueue_/vi->svq->vq_ops->/)
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently fill all of RX ring, then add_buf
returns ENOSPC, which gets mis-detected as an out of
memory condition and causes us to reschedule the work,
and so on forever. Fix this by oom = err == -ENOMEM;
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a number of issues in the statistics gathering of
the s2io driver.
On Xframe adapters, the received multicast statistics counter includes
pause frames which are not indicated to the driver. This can cause
issues where the multicast packet count is higher than what has actually
been received, possibly higher than the number of packets received.
The driver software counters are replaced with the adapter hardware
statistics for rx_packets, rx_bytes, and tx_bytes. It also uses the
overflow registers to determine if the statistics wrapped the 32bit
register (removing the window of having a statistic value less than the
previous call). rx_length_errors statistic now includes undersized
packets in addition to oversized packets in its counting. Finally,
rx_crc_errors are now being counted.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some ocasions the function qlge_io_resume() tries to add a
pending timer, which causes the system to hit the BUG() on
add_timer() function.
This patch removes the timer during the EEH recovery.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge driver calls add_timer() instead of mod_timer().
This patch changes add_timer() to mod_timer(), which seems a better
solution.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_printk() follows the net_device's parent device pointer, so
we must set that earlier than we previously did.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c17b274dc2.
That change was reported to break rndis_wlan support for the WUSB54GS.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ppc4xx adma driver to use new node pointer location
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As Nehalem/Nehalem-EP/Westmere devices uses several devices for the same
functionality (memory controller), the default way of proping devices doesn't
work. So, instead of a per-device probe, all devices should be probed at once.
This means that we should block any new attempt of probe, otherwise, it will
try to register the same device several times.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Nehalem/Nehalem-EP/Westmere, the first QPI device is the last PCI bus.
The last bus is generally at 0x3f or 0xff, but there are also other systems
using different setups. For example, HP Z800 has 0x7f as the last bus.
This patch adds a logic to discover the last bus, dynamically detecting it
at runtime.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.
The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
When calculating the DCT channel from the syndrome we need to know the
syndrome type (x4 vs x8). On F10h, this is read out from extended PCI
cfg space register F3x180 while on K8 we only support x4 syndromes and
don't have extended PCI config space anyway.
Make the code accessing F3x180 F10h only and fall back to x4 syndromes
on everything else.
Cc: <stable@kernel.org> # .33.x .34.x
Reported-by: Jeffrey Merkey <jeffmerkey@gmail.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Fixed include error, changed to linux/io.h
Signed-off-by: Cody Rester <codyrester@gmail.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix page flip finish vs. prepare on plane B
drm/i915: change default panel fitting mode to preserve aspect ratio
drm/i915: fix uninitialized variable warning in i915_setup_compression()
drm/i915: take struct_mutex in i915_dma_cleanup()
drm/i915: Fix CRT hotplug regression in 2.6.35-rc1
i915: fix ironlake edp panel setup (v4)
drm/i915: don't access FW_BLC_SELF on 965G
drm/i915: Account for space on the ring buffer consumed whilst wrapping.
drm/i915: gen3 page flipping fixes
drm/i915: don't queue flips during a flip pending event
drm/i915: Fix incorrect intel_ring_begin size in BSD ringbuffer.
drm/i915: Turn on 945 self-refresh only if single CRTC is active
drm/i915/gen4: Fix interrupt setup ordering
drm/i915: Use RSEN instead of HTPLG for tfp410 monitor detection.
drm/i915: Move non-phys cursors into the GTT
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
(Included the "fix page flip finish vs. prepare on plane B" patch from
Jesse on top of the pull request from Eric. -- Linus)
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_generic: implement ATA_GEN_* flags and force enable DMA on MBP 7,1
ahci,ata_generic: let ata_generic handle new MBP w/ MCP89
libahci: Fix bug in storing EM messages
When booting 2.6.35-rc3 on a x86 system without an ERST ACPI table with
the 'quiet' option, we still observe an "ERST: Table is not found!"
warning.
Quiesce it to the same info log level as the other 'table not found'
warnings.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 4bdadb9785 ("drm/i915:
Selectively enable self-reclaim"), we've been passing GFP_MOVABLE to the
i915 page allocator where we weren't before due to some over-eager
removal of the page mapping gfp_flags games the code used to play.
This caused hibernate on Intel hardware to result in a lot of memory
corruptions on resume. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=13811
Reported-by: Evengi Golov (in bugzilla)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
Cc: stable@kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We did this a long time ago in the DDX driver, but now this fix belongs
in the kernel.
Preserving the aspect ratio is a nicer default.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=18033.
Tested-by: Josh Triplett <josh@freedesktop.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes:
drivers/gpu/drm/i915/i915_dma.c: In function ‘i915_setup_compression’:
drivers/gpu/drm/i915/i915_dma.c:1311: error: ‘compressed_llb’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_cleanup_ring_buffer() calls drm_gem_object_unreference() (as
opposed to drm_gem_object_unreference_unlocked()) so it needs to be
called with "struct_mutex" held. If we don't hold the lock, it triggers
a BUG_ON(!mutex_is_locked(&dev->struct_mutex));
I also audited the other places that call intel_cleanup_ring_buffer()
and they all hold the lock so they're OK.
This was introduced in: 8187a2b70e "drm/i915: introduce
intel_ring_buffer structure (V2)" and it's a regression from v2.6.34.
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=16247
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reported-by: Benny Halevy <bhalevy@panasas.com>
Tested-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
The eDP spec claims a 20% overhead for the 8:10 encoding scheme used
on the wire. Take this into account when picking the lane/clock speed
for the panel.
v3: some panels are out of spec, try our best to deal with them, don't
refuse modes on eDP panels, and try the largest allowed settings if
all else fails on eDP.
v4: fix stupid typo, forgot to git add before amending.
Fixes several reports in bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=28070
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The register offset for FW_BLC_SELF is a totally different set of bits
on Broadwater (it's actually MI_RDRET_STATE), so don't treat it like
FW_BLC_SELF on 965G chips.
Fixes bug https://bugs.freedesktop.org/show_bug.cgi?id=26874.
Cc: stable@kernel.org
Tested-by: Norman Yarvin <yarvin@yarchive.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we fill the tail of the physical ring buffer with NOOP when wrapping,
we need to account for the reduction in available space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
IDE mode of MCP89 on MBP 7,1 doesn't set DMA enable bits in the BMDMA
status register. Make the following changes to work around the problem.
* Instead of using hard coded 1 in id->driver_data as class code
match, use ATA_GEN_CLASS_MATCH and carry the matched id in
host->private_data.
* Instead of matching PCI_VENDOR_ID_CENATEK, use ATA_GEN_FORCE_DMA
flag in id instead.
* Add ATA_GEN_FORCE_DMA to the id entry of MBP 7,1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For yet unknown reason, MCP89 on MBP 7,1 doesn't work w/ ahci under
linux but the controller doesn't require explicit mode setting and
works fine with ata_generic. Make ahci ignore the controller on MBP
7,1 and let ata_generic take it for now.
Reported in bko#15923.
https://bugzilla.kernel.org/show_bug.cgi?id=15923
NVIDIA is investigating why ahci mode doesn't work.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In function ahci_store_em_buffer(), if the input (signed char*) buffer
contains negative data, the constructed 32-bit long message data may
be wrong.
Signed-off-by: Harry Zhang <harry.zhang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: remove rv100 bios connector quirk
drm/radeon/kms/pm: fix power state indexing on igp chips in dynpm mode
DRM / radeon / KMS: Fix hibernation regression related to radeon PM (was: Re: [Regression, post-2.6.34] Hibernation broken on machines with radeon/KMS and r300)
drm/radeon/kms/igp: fix possible divide by 0 in bandwidth code (v2)
drm/radeon: add quirk to make HP nx6125 laptop resume.
drm/radeon/kms: add some missing regs to evergreen gpu init
drm/radeon/kms: fix typos in evergreen command checker
drm/radeon/kms: avoid oops on mac r4xx cards
fb: fix colliding defines for fb flags.
drm/radeon/kms: Force HDP_NONSURF to maximum size
drm/radeon/kms: disable frac fb dividers for rs6xx
drm/radeon/kms: don't read attempt to read bios from VRAM on unposted GPU.
drm/radeon/kms: fix typo in evergreen_gpu_init
drm/radeon/kms: return ret in cursor_set failure path
drm/ttm: non pooled page allocation should have GFP_USER set
drm/radeon/r100/r200: fix calculation of compressed cube maps
drm/radeon/r200: handle more hw tex coord types
drm/radeon/kms: CS checker texture fixes for r1xx/r2xx/r3xx
drm/radeon: add fake RN50 table for powerpc
drm/fb: Fix video= mode computation
...
patch 'break out of polling loop on error' caused
a minor performance regression on my machine: recover
that performance by adding a bunch of unlikely annotations
in the error handling.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 0224cf4c5e (sched: Intoduce get_cpu_iowait_time_us())
broke things by not making sure preemption was indeed disabled
by the callers of nr_iowait_cpu() which took the iowait value of
the current cpu.
This resulted in a heap of preempt warnings. Cure this by making
nr_iowait_cpu() take a cpu number and fix up the callers to pass
in the right number.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-pm@lists.linux-foundation.org
LKML-Reference: <1277968037.1868.120.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some RV100 cards with 2 VGA ports show up with DVI+VGA, however
some boards with DVI+VGA have the same subsystem ids. Better
to have a VGA port show up as DVI than having a non-useable
DVI port.
reported by DHR in irc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a regression from 2.6.34 related to the recent radeon power
management changes, caused by attempting to cancel a delayed work
item that's never been scheduled. However, the code as is has some
other issues potentially leading to visible problems.
First, the mutex around cancel_delayed_work() in radeon_pm_suspend()
doesn't really serve any purpose, because cancel_delayed_work() only
tries to delete the work's timer. Moreover, it doesn't prevent the
work handler from running, so the handler can do some wrong things if
it wins the race and in that case it will rearm itself to do some
more wrong things going forward. So, I think it's better to wait for
the handler to return in case it's already been queued up for
execution. Also, it should be prevented from rearming itself in that
case.
Second, in radeon_set_pm_method() the cancel_delayed_work() is not
sufficient to prevent the work handler from running and queing up
itself for the next run (the failure scenario is that
cancel_delayed_work() returns 0, so the handler is run, it waits on
the mutex and then rearms itself after the mutex has been released),
so again the work handler should be prevented from rearming itself in
that case..
Finally, there's a potential deadlock in radeon_pm_fini(), because
cancel_delayed_work_sync() is called under rdev->pm.mutex, but the
work handler tries to acquire the same mutex (if it wins the race).
Fix the issues described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table. Check both and make sure
we have a value system memory clock value.
v2: make sure rs690_pm_info is called on rs780/rs880 as well.
fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For some reason on resume, executing the BIOS scripts locks up the whole chipset, by avoiding the dynclk table the machine resumes properly and seems to function okay.
Signed-off-by: Dave Airlie <airlied@redhat.com>
They don't have an atombios so don't attempt to use it for
eng/mem clocks.
Reported by spoonb on #radeon
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28671
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
HDP non surface should cover the whole VRAM but we were misscomputing
the size and we endup in some case not covering the VRAM at all (if
VRAM size were > 1G). Covering more than the VRAM size shouldn't be
an issue.
Fix : https://bugs.freedesktop.org/show_bug.cgi?id=28016
[airlied: add evergreen fix]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since the VGA switcheroo, we'd attempt to read the BIOS from VRAM on startup
but on some unposted cards this can cause hangs/crashes.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=28592
(further problem pointed out by agd5f on IGP systems)
Reported-by: Reilithion on #radeon
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were returning 0 in both the success and failure paths. Noticed while
investigating FDO bug 26403.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Non pooled page allocation should have GFP_USER set so allocation
can wait and reclaim page from other process (ie non atomic).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This needs similar handling to other compressed textures.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Code did not handle projected 2d and depth coordinates, meaning potentially
set 3d or cube special handling might stick.
(Not sure what depth coord actually does, but I guess handling it
like a normal coordinate is the right thing to do.)
Might be related to https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28459
agd5f: apply to r1xx/r2xx as well.
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This works well enough on a js21, but it would be nice if IBM could supply
more tables for the later Power6/7 machines.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reduced blanking is valid only when doing CVT modes. Also, generate GTF
modes unless CVT was requested; CVT devices are required to support GTF,
but the reverse is not true.
[airlied: fix typo]
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The transmitter needs to be enabled before the link is trained.
Reported-By: Lars Doelle <lars.doelle@on-line.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When suspending, we turn the display hw off, at resume the screen will stay black.
This patch turn it on. Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16180
Signed-off-by: Cedric Godin <cedric.godin@skynet.be>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
USB: gadget: f_mass_storage: stale common->fsg value bug fix
USB: gadget: f_mass_storage: fixed fs descriptors not being updated
USB: musb: Enable the maximum supported burst mode for DMA
USB: musb: fix Blackfin ulpi stubs
USB: MUSB: make non-OMAP platforms build with CONFIG_PM=y
USB: musb_core: make disconnect and suspend interrupts work again
USB: obey the sysfs power/wakeup setting
USB: gadget eth: Fix calculate CRC32 in EEM
USB: qcserial: fix a memory leak in qcprobe error path
USB: gadget/printer, fix sleep inside atomic
USB: isp1362-hcd, fix double lock
USB: serial: ftdi: correct merge conflict with CONTEC id
USB: fix oops in usb_sg_init()
USB: s3c2410: deactivate endpoints before gadget unbinding
USB: ehci-mxc: bail out on transceiver problems
USB: otg/ulpi: bail out on read errors
usb: musb: Fix a bug by making suspend interrupt available in device mode
USB: r8a66597: Fix failure in change of status
USB: xHCI: Fix bug in link TRB activation change.
USB: gadget: g_fs: possible invalid pointer reference bug fixed
...
When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.
What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.
See more information including the relevant functions below:
System 1 System 2
bond0 bond0
ping <system2>
ARP request --------->
<--------- ARP reply
+->rlb_arp_recv <---------------------+ <--- loop begins
| rlb_update_entry_from_arp |
| client_info->ntt = 1; |
| bond_info->rx_ntt = 1; |
| |
| <communication succeed> |
| |
| bond_alb_monitor |
| rlb_update_rx_clients |
| rlb_update_client |
| arp_create(ARPOP_REPLY) |
| send ARP reply --------------> V
| send ARP reply -------------->
| rlb_arp_recv
| rlb_update_entry_from_arp
| client_info->ntt = 1;
| bond_info->rx_ntt = 1;
| < snipped, same as in system 1>
+------- <-------------- send ARP reply
<-------------- send ARP reply
Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.
This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix abuse of the preincrement operator as detected when building with gcc
4.6.0:
CC [M] drivers/bluetooth/hci_bcsp.o
drivers/bluetooth/hci_bcsp.c: In function 'bcsp_prepare_pkt':
drivers/bluetooth/hci_bcsp.c:247:20: warning: operation on 'bcsp->msgq_txseq' may be undefined
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another device ID as listed in the vendor driver version
0003.0825.2009.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are only 6 elements in the cb_pcidda_boards[] array so the
original code read past the end. After this change nothing uses N_BOARDS
so I removed the definition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds some device ids.
The list of supported devices was extracted from realteks driver package.
(0x050d, 0x815F) and (0x0df6, 0x004b) are not in the official list of
supported devices and may not work correctly.
In case of problems with these, they should probably be removed from the list.
Signed-off-by: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit bbfb5652, the spacing in the definitions of eqMacAddr and cpMacAddr
in drivers/staging/rtl8187se/r8180_core.c were changed to conform to kernel
standards. These definitions were duplicates of lines found in
drivers/staging/rtl8187se/ieee80211/dot11d.h. Once the change was made, the
following warnings were emitted:
CC [M] drivers/staging/rtl8187se/r8180_core.o
drivers/staging/rtl8187se/r8180_core.c:69:0: warning: "eqMacAddr" redefined
drivers/staging/rtl8187se/ieee80211/dot11d.h:39:0: note: this is the location of the previous definition
drivers/staging/rtl8187se/r8180_core.c:70:0: warning: "cpMacAddr" redefined
drivers/staging/rtl8187se/ieee80211/dot11d.h:40:0: note: this is the location of the previous definition
The fix is to keep only the difinition in the header file.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I got a wlags49_h2 driver build error in linux-next when CONFIG_SYSFS is not set.
CC [M] drivers/staging/wlags49_h2/wl_cs.o
In file included from drivers/staging/wlags49_h2/wl_cs.c:104:
drivers/staging/wlags49_h2/wl_sysfs.h: In function ‘register_wlags_sysfs’:
drivers/staging/wlags49_h2/wl_sysfs.h:5: error: parameter name omitted
drivers/staging/wlags49_h2/wl_sysfs.h: In function ‘unregister_wlags_sysfs’:
drivers/staging/wlags49_h2/wl_sysfs.h:6: error: parameter name omitted
make[1]: *** [drivers/staging/wlags49_h2/wl_cs.o] Error 1
make: *** [_module_drivers/staging/wlags49_h2] Error 2
This is due a wrong function definition (it does not include parameters names).
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On ia64, the build fails with incompatible implicit definition of strlen.
This patch adds the <linux/string.h> include to get the real prototype.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a possible race condition when hv_utils starts to load immediately
after hv_vmbus is loading - null pointer error could happen.
This patch added wait/completion to ensure all channels are ready before
vmbus loading completes. So another module won't have any uninitialized channel.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I received a report that AI streaming acquisitions do not work properly
for the adl_pci9111 driver when convert_src is TRIG_TIMER and
scan_begin_src is TRIG_FOLLOW (and scan_begin_arg is therefore 0). This
seems to be down to the incorrect setting of dev_private->scan_delay in
pci9111_ai_do_cmd(). Under the previously stated conditions,
dev_private->scan_delay ends up set to (unsigned int)-1, but it ought to
be set to 0. The function sets it to 0 initially, and it only makes
sense to change it if both convert_src and scan_begin_src are set to
TRIG_TIMER.
Note: 'scan_delay' is the number of unwanted scans to discard after each
valid scan. The hardware does not support 'scan' timing as such, just a
regularly paced conversion timer (with automatic channel switching
between conversions). The driver simulates a scan period that is some
(>1) multiple of the conversion period times the scan length
(chanlist_len samples) by reading chanlist_len samples and discarding
the next scan_delay times chanlist_len samples.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I moved the kfree() down a couple lines after the dereference.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile warning in staging/batman-adv.
This is due a struct bin_attribute read function prototype change and the driver was not updated.
This patch solves the issue
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns the number of bites remaining but we want to
return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On fsg_unbind the common->fsg pointer was not NULLed if the
unbound fsg_dev instance was the current one. As an effect,
the incorrect pointer was preserved in all further operations
which caused do_set_interface to reference an invalid region.
This commit fixes this by raising an exception in fsg_bind
which will change the common->fsg pointer. This also requires
an wait queue so that the thread in fsg_bind can wait till the
worker thread handles the exception.
This commit removes also a config and new_config fields of
fsg_common as they are no longer needed since fsg can be
used to determine whether function is active or not.
Moreover, this commit removes possible race condition where
the fsg field was modified in both the worker thread and
form various other contexts. This is fixed by replacing
prev_fsg with new_fsg. At this point, fsg is assigned only
in worker thread.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The full speed descriptors were copied to the usb_function structure
in the fsg_bind_config function before call to the usb_ep_autoconfig.
The usb_ep_autoconfig was called in fsg_bind using the original
descriptors. In effect copied descriptors were not updated.
This patch changes the copy full speed descriptors after the call to
usb_op_autoconfig is performed. This way, copied full speed
descriptors have updated values.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Tested-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting MUSB Burst Mode 3 automatically enables support for
lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified
length). There is no need to set these burst modes based on the
packet size. Also enable the burst mode for both mode1 and mode0.
This is a fix for buggy hardware - having the lower burst modes
enabled can potentially cause lockups of the DMA engine used in
OMAP2/3/4 chips.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attempt to build MUSB driver with CONFIG_PM=y (e.g. in the OTG mode) on DaVinci
results in these link errors:
drivers/built-in.o: In function `musb_restore_context':
led-triggers.c:(.text+0x714d8): undefined reference to
`musb_platform_restore_context'
drivers/built-in.o: In function `musb_save_context':
led-triggers.c:(.text+0x71788): undefined reference to
`musb_platform_save_context'
This turned out to be caused by commit 9957dd97ec
(usb: musb: Fix compile error for omaps for musb_hdrc). Revert it, taking into
account the rename of CONFIG_ARCH_OMAP34XX into CONFIG_ARCH_OMAP3 (which that
commit fixed in a completely inappropriate way) and the recent addition of
OMAP4 support.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 1c25fda4a0 (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1403) is a partial reversion of an earlier change
(commit 5f677f1d45 "USB: fix remote
wakeup settings during system sleep"). After hearing from a user, I
realized that remote wakeup should be enabled during system sleep
whenever userspace allows it, and not only if a driver requests it
too.
Indeed, there could be a device with no driver, that does nothing but
generate a wakeup request when the user presses a button. Such a
device should be allowed to do its job.
The problem fixed by the earlier patch -- device generating a wakeup
request for no reason, causing system suspend to abort -- was also
addressed by a later patch ("USB: don't enable remote wakeup by
default", accepted but not yet merged into mainline). The device
won't be able to generate the bogus wakeup requests because it will be
disabled for remote wakeup by default. Hence this reversion will not
re-introduce any old problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CRC should be calculated for Ethernet frame, not for whole recievede EEM data.
This bug shows rarely, because in many times len == skb->len.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds missing kfree(data) before return -ENODEV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found that sleep is called inside atomic context created by
lock_printer_io spinlock in several functions. It's used in process
context only and some functions sleep inside its critical section. As
this is not allowed for spinlocks, switch it to mutex.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Craig W. Nadler <craig@nadler.us>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found that isp1362_sw_reset tries to take a isp1362_hcd->lock,
but it is already held in isp1362_hc_stop. Avoid that by introducing
__isp1362_sw_reset which doesn't take the lock and call it from
isp1362_hc_stop. isp1362_sw_reset is then as simple as lock --
__isp1362_sw_reset -- unlock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.
I believe the merge problem occurred with the commit:
dee5658b48
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1401) fixes a bug in usb_sg_init() that can cause an
invalid pointer dereference. An inner loop reuses some local variables
in an unsafe manner, so new variables are introduced.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget disconnect must be called before unbinding to avoid races.
The change fixes an oops on g_ether module unregistering.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written.
See Commit 1c25fda4a0 (usb: musb: handle
irqs in the order dictated by programming guide)
With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.
The fix brings suspend interrupt handling outside
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the change by 749da5f82f,
The change in the status when the USB device is connected is wrong.
Therefore, the device is not recognized.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Paul Mundt" <lethal@linux-sh.org>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6c12db90f1 introduced a bug for
control transfers. The patch was supposed to change when the link TRBs at
the end of each ring segment were given to the hardware. If a transfer
descriptor (TD) ended just before the link TRB, the code wouldn't give
back the link TRB to the hardware; instead it would be given back in
prepare_ring() just before the next TD was enqueued at the top of the
ring.
Unfortunately, the code relied on checking the chain bit of the TRB to
determine whether the TD ended just before the link TRB. It assumed that
the ring enqueuing code would call prepare_ring() before enqueuing the
next TD. However, control transfers are made of multiple TDs, and
prepare_ring() is only called once before enqueuing two or three TDs.
If the first or second TD of the control transfer ended just before the
link TRB, then the code in inc_enq() would not move the enqueue pointer
past the link TRB, and the link TRB would get overwritten. This would
cause the xHCI driver to start writing to memory past the ring segment,
and eventually the system would crash or hang.
The fix is to add a flag to inc_enq() that says whether the caller will
enqueue more TDs before calling prepare_ring(). If the chain bit is
cleared (meaning this is the last TRB in a TD), and the caller will not
enqueue more TDs, then we defer giving back the link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During __gfs_do_config() some invalid pointers may be left
in usb_configuration::interfaces array from previous calls
to the __gfs_do_config() for the same configuration. This
will always happen if an user space function which has
a fewer then the last user space function registers itself.
Composite's set_config() function that a pointer after the
last interface in usb_configuration::interface is NULL
unless the array is full.
This patch makes the __gfs_do_config() make sure that if the
usb_configuration::interface is not full then a pointer
after the last interface is NULL.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call put_tty_driver() in cleanup function, to fix Oops when trying to open
gadget serial char device after module unload.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No longer set low_latency flag as it causes this warning backtrace:
WARNING: at kernel/mutex.c:207 __mutex_lock_slowpath+0x6c/0x288()
Fix associated locking and wakeups.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: Maulik Mankad <x0082077@ti.com>
Cc: stable <stable@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cpm_uart_early_write() function which was used for console poll
isn't implemented in the cpm uart driver.
Implementing this function both fixes the build when CONFIG_CONSOLE_POLL
is set and allows kgdboc to work via the cpm uart.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just
add a test to check skb->protocol. It may crash on short packets due
to ip_hdr() access.
Signed-off-by: Guillaume Gaudonville <guillaume.gaudonville@6wind.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling the tx laser while receiving DMA requests
can hang the device. After this occurs the device
is in a bad state. The GPIO bit never clears when
PCI master access is disabled and a reboot is required
to get the device in a good state again.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added to 2.6.34:
commit 5f6c018199
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date: Wed Apr 14 16:04:23 2010 -0700
ixgbe: fix bug with vlan strip in promsic mode
among other things added a function called ixgbe_vlan_filter_enable.
This new function wants to access and set some rx_ring parameters, but
adapter->rx_ring has already been freed. This simply moves the free
until after the access and makes __ixgbe_shutdown look more like
ixgbe_remove.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a nuc900 lcd build error.
Since the 'nuc900_driver_clksrc_div()' API cannot be merged into mainline
successfully, I removed this clock source selection hook in this driver.
This means nuc900 lcd driver has to select default clock source from the
external crystal now.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Qiang Wang <rurality.wq@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update Kconfig and Makefile in drivers/gpio to discourage inappropriate
addition of platform-specific code.
[akpm@linux-foundation.org: fix tpyo]
Signed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ds1307 driver misreads the ds1388 registers when checking for 12 or 24
hour mode. Instead of checking the hour register it reads the minute
register. Therefore the driver thinks minutes >= 40 has the 12HR bit set
and resets the minute register by zeroing the high bits. This results in
minutes are reset to 0-9, jumping back in time 40 or 50 minutes. The time
jump is also written back to the RTC.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a regression introduced by ae74e823cb ("ipmi: add parameter to limit
CPU usage in kipmid").
Some systems were seeing CPU usage go up dramatically with the recent
changes to try to reduce timer usage in the IPMI driver. This was traced
down to schedule_timeout_interruptible(1) being changed to
schedule_timeout_interruptbile(0). Revert that part of the change.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16147
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Cc: <stable@kernel.org> [2.6.34.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ipmi code will never register a PCI or Open Firmware driver if a
hardcoded device is provided by the user by providing device addresses via
the module parameters. This can cause us to attempt to unregister a
driver that was never registered, resulting in an oops. Keep track of
registration in order to avoid this.
Fixes a post-2.6.34 regression.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.data+0x196e8): Section mismatch in reference from the
variable lxfb_driver to the function .init.text:lxfb_probe() The variable
lxfb_driver references the function __init lxfb_probe()
This changes lxfb_probe and friends to use __devinit, and also adds
__devexit to lxfb_remove.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.data+0x195d8): Section mismatch in reference from the
variable gxfb_driver to the function .init.text:gxfb_probe() The variable
gxfb_driver references the function __init gxfb_probe()
This changes gxfb_probe and friends to use __devinit, and also adds
__devexit to gxfb_remove.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Don't count_vm_events for discard bio in submit_bio.
cfq: fix recursive call in cfq_blkiocg_update_completion_stats()
cfq-iosched: Fixed boot warning with BLK_CGROUP=y and CFQ_GROUP_IOSCHED=n
cfq: Don't allow queue merges for queues that have no process references
block: fix DISCARD_BARRIER requests
cciss: set SCSI max cmd len to 16, as default is wrong
cpqarray: fix two more wrong section type
cpqarray: fix wrong __init type on pci probe function
drbd: Fixed a race between disk-attach and unexpected state changes
writeback: fix pin_sb_for_writeback
writeback: add missing requeue_io in writeback_inodes_wb
writeback: simplify and split bdi_start_writeback
writeback: simplify wakeup_flusher_threads
writeback: fix writeback_inodes_wb from writeback_inodes_sb
writeback: enforce s_umount locking in writeback_inodes_sb
writeback: queue work on stack in writeback_inodes_sb
writeback: fix writeback completion notifications
Support for netpoll over bonded interfaces was added here:
commit f6dc31a85c
Author: WANG Cong <amwang@redhat.com>
Date: Thu May 6 00:48:51 2010 -0700
bonding: make bonding support netpoll
but it is bad enough that we should probably just disable netpoll over
bonding until some of the locking logic in the bonding driver is changed
or converted completely to RCU. Simple actions like changing the active
slave in active-backup mode will hang the box if a high enough printk
debugging level is enabled.
Keeping the old code around will be good for anyone that wants to work
on it (and for after the RCU conversion), so I propose this small patch
rather than ripping it all out.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Folklore suggested that such systems existed
in the pre-history of ACPI.
However, we removed the SCI_EN polling loop from
acpi_hw_set_mode() in b430acbd7c
because it delayed resume by 3 seconds on boxes
that refused to set SCI_EN.
Matthew removed the call to acpi_enable() from
the suspend resume path.
James found a modern system that still needs to be polled
upon boot.
So here we restore the workaround, except that we
put it in acpi_enable() rather than the low level
acpi_hw_set_mode().
https://bugzilla.kernel.org/show_bug.cgi?id=16271
Signed-off-by: Len Brown <len.brown@intel.com>
* 'fixes' of ssh://master.kernel.org/~sfr/next-fixes:
acpi: update gfp/slab.h includes
ocfs2: update gfp/slab.h includes
davinci: update gfp/slab.h includes
arm: update gfp/slab.h includes
v4l-dvb: update gfp/slab.h includes
* 'for-linus' of git://neil.brown.name/md:
md/raid5: don't include 'spare' drives when reshaping to fewer devices.
md/raid5: add a missing 'continue' in a loop.
md/raid5: Allow recovered part of partially recovered devices to be in-sync
md/raid5: More careful check for "has array failed".
md: Don't update ->recovery_offset when reshaping an array to fewer devices.
md/raid5: avoid oops when number of devices is reduced then increased.
md: enable raid4->raid0 takeover
md: clear layout after ->raid0 takeover
md: fix raid10 takeover: use new_layout for setup_conf
md: fix handling of array level takeover that re-arranges devices.
md: raid10: Fix null pointer dereference in fix_read_error()
Restore partition detection of newly created md arrays.
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
phylib: Add autoload support for the LXT973 phy.
ISDN: hysdn, fix potential NULL dereference
vxge: fix memory leak in vxge_alloc_msix() error path
isdn/gigaset: correct CAPI connection state storage
isdn/gigaset: encode HLC and BC together
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
isdn/gigaset: correct CAPI voice connection encoding
isdn/gigaset: honor CAPI application's buffer size request
cpmac: do not leak struct net_device on phy_connect errors
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
ipv6: fix NULL reference in proxy neighbor discovery
Bluetooth: Bring back var 'i' increment
xfrm: check bundle policy existance before dereferencing it
sky2: enable rx/tx in sky2_phy_reinit()
cnic: Disable statistics initialization for eth clients that do not support statistics
net: add dependency on fw class module to qlcnic and netxen_nic
snmp: fix SNMP_ADD_STATS()
hso: remove setting of low_latency flag
udp: Fix bogus UFO packet generation
lasi82596: fix netdev_mc_count conversion
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
MAINTAINERS - Add an entry for the input MT protocol
Input: wacom - fix serial number handling on Cintiq 21UX2
Input: fixup X86_MRST selects
Input: sysrq - fix "stuck" SysRq mode
Input: ad7877 - fix spi word size to 16 bit
Input: pcf8574_keypad - fix off by one in pcf8574_kp_irq_handler()
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k8temp) Bypass core swapping on single-core processors
hwmon: (i5k_amb) Fix sysfs attribute for lockdep
hwmon: (k10temp) Do not blacklist known working CPU models
* git://git.infradead.org/iommu-2.6:
intel-iommu: Force-disable IOMMU for iGFX on broken Cantiga revisions.
intel-iommu: Fix double lock in get_domain_for_dev()
intel-iommu: Fix reference by physical address in intel_iommu_attach_device()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fix de2104x driver failing to readout MAC address correctly
alpha: Detect Super IO chip, no IDE on Avanti, enable EPP19
alpha: fix pci_mmap_resource API breakage
alpha: fix __arch_hweight32 typo
When ring parsing fails, we currently handle this
as ring empty condition. This means that we enable
kicks and recheck ring empty: if this not empty,
we re-start polling which of course will fail again.
Instead, let's return a negative error code and stop polling.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that lp is dereferenced earlier than checked for being
NULL in hysdn_rx_netpkt. Move the initialization below the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked.
While at it, use the centralized exit idiom in the function.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAPI applications can handle several connections in parallel,
so one connection state per application isn't sufficient.
Store the connection state in the channel structure instead.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt to buggy device firmware which accepts setting HLC only in the
same command line as BC, by encoding HLC and BC in a single command
if both are specified, and rejecting HLC without BC.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Gigaset CAPI driver handled all DATA_B3_REQ messages as if the
Delivery Confirmation flag bit was set, delaying the emission of the
DATA_B3_CONF reply until the data was actually transmitted. Some
CAPI applications (notably Asterisk) aren't happy with that
behaviour. Change it to actually evaluate the Delivery Confirmation
flag as described the CAPI specification.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Gigaset CAPI driver select L2_VOICE (AT^SBPR=2) as the
layer 2 encoding for transparent connections, like the ISDN4Linux
variant. L2_BITSYNC (AT^SBPR=0) mutes internal connections and
distorts external ones.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the Gigaset CAPI driver to limit the length of a connection's
payload data receive buffers to the corresponding CAPI application's
data buffer size, as some real-life CAPI applications tend to be
rather unhappy if they receive bigger data blocks than requested.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91c92_cs:
Fix the problem that lan & modem does not work simultaneously
in the Megahertz multi-function card.
We need to write MEGAHERTZ_ISR to retrigger interrupt.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.
Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:
commit 1152dcc28c
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jan 15 13:42:58 2010 -0800
iwlwifi: Fix throughput stall issue in HT mode for 5000
Similar to 6000 and 1000 series, RTS/CTS is the recommended
protection mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.
The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).
Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are few situations where it would make any sense to add a spare
when reducing the number of devices in an array, but it is
conceivable: A 6 drive RAID6 with two missing devices could be
reshaped to a 5 drive RAID6, and a spare could become available
just in time for the reshape, but not early enough to have been
recovered first. 'freezing' recovery can make this easy to
do without any races.
However doing such a thing is a bad idea. md will not record the
partially-recovered state of the 'spare' and when the reshape
finished it will think that the spare is still spare.
Easiest way to avoid this confusion is to simply disallow it.
Signed-off-by: NeilBrown <neilb@suse.de>
As the comment says, the tail of this loop only applies to devices
that are not fully in sync, so if In_sync was set, we should avoid
the rest of the loop.
This bug will hardly ever cause an actual problem. The worst it
can do is allow an array to be assembled that is dirty and degraded,
which is not generally a good idea (without warning the sysadmin
first).
This will only happen if the array is RAID4 or a RAID5/6 in an
intermediate state during a reshape and so has one drive that is
all 'parity' - no data - while some other device has failed.
This is certainly possible, but not at all common.
Signed-off-by: NeilBrown <neilb@suse.de>
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.
This is particularly important for a reshape which suffers device
failure. Treating the data as in-sync can mean the difference between
data-safety and data-loss.
Signed-off-by: NeilBrown <neilb@suse.de>
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.
In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.
So encode this subtlety in a new function and call it as appropriate.
The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:
good good good good incomplete good good failed failed
while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.
Reported-by: Terry Morris <tbmorris@tbmorris.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
Signed-off-by: NeilBrown <neilb@suse.de>
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
Signed-off-by: NeilBrown <neilb@suse.de>
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover(). That
gets set in run()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit b821eaa572 broke partition
detection for md arrays.
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
add_buf returns ring size on out of memory,
this is not what devices expect.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Cintiq 21UX2 added 8 more bits for the tool serial number and more
buttons for the expresskey. We did not enable them properly in the
last patch.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some of the recent X86_MRST additions make some "select"s
conditional on X86_MRST but missed some related kconfig symbols,
causing:
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ab2): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ae1): undefined reference to `i8042_unlock_chip'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b40): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b6f): undefined reference to `i8042_lock_chip'
when SERIO_I8042=m, SERIO_LIBPS2=y, KEYBOARD_ATKBD=y.
We need to make i8042 dependant upon !X86_MRST and allow deselecting
atkbd on Moorestown even when !CONFIG_EMBEDDED.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous CMT fixup accidentally copied in the TMU shift value, reset
this back to its original value while preserving the TMU fix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
The ds2782_get_capacity function should return 0 on success, not the
capacity value.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The path around the loop ends with the lock held, so the call to mutex_lock
is moved before the beginning of the loop.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@locked@
expression E1;
position p;
@@
read_lock(E1@p,...);
@r exists@
expression x <= locked.E1;
expression locked.E1;
expression E2;
identifier lock;
position locked.p,p1,p2;
@@
*lock@p1 (E1@p,...);
... when != E1
when != \(x = E2\|&x\)
*lock@p2 (E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a2e066bba2 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Rick Moritz <rhavin@gmx.net>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
i5k_amb.ko uses dynamically allocated memory (by kmalloc) for
attributes passed to sysfs. So, sysfs_attr_init() should be called
for working happy with lockdep.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [2.6.34 only]
When detecting AM2+ or AM3 socket with DDR2, only blacklist cores
which are known to exist in AM2+ format.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Hardware will set the flip pending ISR bit as soon as it receives the
flip instruction, and (supposedly) clear it once the flip completes
(e.g. at the next vblank). If we try to send down a flip instruction
while the ISR bit is set, the hardware can become very confused, and we
may never receive the corresponding flip pending interrupt, effectively
hanging the chip.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit c7f486567c
(PCI PM: PCIe PME root port service driver) causes the native PCIe
PME signaling to be used by default, if the BIOS allows the kernel to
control the standard configuration registers of PCIe root ports.
However, the native PCIe PME is coupled to the native PCIe hotplug
and calling pcie_pme_acpi_setup() makes some BIOSes expect that
the native PCIe hotplug will be used as well. That, in turn, causes
problems to appear on systems where the PCIe hotplug driver is not
loaded. The usual symptom, as reported by Jaroslav Kameník and
others, is that the ACPI GPE associated with PCIe hotplug keeps
firing continuously causing kacpid to take substantial percentage
of CPU time.
To work around this issue, change the default so that the native
PCIe PME signaling is only used if directly requested with the help
of the pcie_pme= command line switch.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15924 , which is
a listed regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Jaroslav Kameník <jaroslav@kamenik.cz>
Tested-by: Antoni Grzymala <antekgrzymala@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit 9630bdd9b1
(ACPI: Use GPE reference counting to support shared GPEs) the wakeup
enable mask bits of GPEs are set as soon as the GPEs are enabled to
wake up the system. Unfortunately, this leads to a regression
reported by Michal Hocko, where a system is woken up from ACPI S5 by
a device that is not supposed to do that, because the wakeup enable
mask bit of this device's GPE is always set when
acpi_enter_sleep_state() calls acpi_hw_enable_all_wakeup_gpes(),
although it should only be set if the device is supposed to wake up
the system from the target state.
To work around this issue, rework the ACPI power management code so
that GPEs are not enabled to wake up the system upfront, but only
during a system state transition when the target state of the system
is known. [Of course, this means that the reference counting of
"wakeup" GPEs doesn't really make sense and it is sufficient to
set/unset the wakeup mask bits for them during system sleep
transitions. This will allow us to simplify the GPE handling code
quite a bit, but that change is too intrusive for 2.6.35.]
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15951
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes dma_get_ops() prefetch optimization in bnx2.
bnx2 uses dma_get_ops() to see if dma_sync_single_for_cpu() is
noop. bnx2 does prefetch if it's noop.
But dma_get_ops() isn't available on all the architectures (only the
architectures that uses dma_map_ops struct have it). Using
dma_get_ops() in drivers leads to compilation breakage on many
architectures.
This patch removes dma_get_ops() and changes bnx2 to do prefetch on
all the architectures. This adds useless prefetch on non-coherent
architectures but this is harmless. It is also unlikely to cause the
performance drop.
[ Remove now unused local variable 'pdev' -DaveM ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the probe() function in the at32ap700x_wdt driver, this to
make sure the miscdev is properly initialized and the driver is ready to be
accessed.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Wim Van sebroeck <wim@iguana.be>
This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs:
serial_cs:
add new id (TOSHIBA Modem/LAN Card)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing the following command on host:
$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1
Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:
skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
Oops: Exception in kernel mode, sig: 5 [#1]
MPC831x RDB
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
NIP: c01c1840 LR: c01c1840 CTR: c016d918
[...]
NIP [c01c1840] skb_over_panic+0x48/0x5c
LR [c01c1840] skb_over_panic+0x48/0x5c
Call Trace:
[c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
[c0339d60] [c01c3020] skb_put+0x5c/0x60
[c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
[c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc
Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:
status=1400 length=1536
status=1800 length=1541
So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.
This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).
Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port reset operations and memory add/remove operations need to
be serialized to avoid a kernel deadlock. The deadlock is caused
by calling the napi_disable() function twice.
Therefore we have to employ the dlpar_mem_lock in the ehea_reset_port
function as well
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the eHEA poll function an rmb() is required. Without that some packets
on the receive queue are not seen and thus delayed until the next interrupt
is handled for the same receive queue.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
