This driver doesn't support normal DMA, only direct access to its
local memory. Remove the HCD_DMA flag to properly express that fact.
Fixes: 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190903084615.19161-3-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver doesn't support normal DMA, only direct access to its
local memory. Remove the HCD_DMA flag to properly express that fact.
Fixes: 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190903084615.19161-2-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoCs may have an optional clock xhci_ck (125M or 200M), it
usually uses the same PLL as sys_ck, so support it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1566542425-20082-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's spelled "renesas", not "renensas".
Due to this typo, RZ/G1M and RZ/G1N were not covered by the check.
Fixes: 2dc240a330 ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Falcon microcontroller that runs the XUSB firmware and which is
responsible for exposing the XHCI interface can address only 40 bits of
memory. Typically that's not a problem because Tegra devices don't have
enough system memory to exceed those 40 bits.
However, if the ARM SMMU is enable on Tegra186 and later, the addresses
passed to the XUSB controller can be anywhere in the 48-bit IOV address
space of the ARM SMMU. Since the DMA/IOMMU API starts allocating from
the top of the IOVA space, the Falcon microcontroller is not able to
load the firmware successfully.
Fix this by setting the DMA mask to 40 bits, which will force the DMA
API to map the buffer for the firmware to an IOVA that is addressable by
the Falcon.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1566989697-13049-1-git-send-email-nkristam@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
[ 34.851754] usb 2-1: USB disconnect, device number 2
[ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 35.187886] Workqueue: usb_hub_wq hub_event
[ 35.192063] Call trace:
[ 35.194509] dump_backtrace+0x0/0x150
[ 35.198165] show_stack+0x14/0x20
[ 35.201475] dump_stack+0xa0/0xc4
[ 35.204785] __report_bad_irq+0x34/0xe8
[ 35.208614] note_interrupt+0x2cc/0x318
[ 35.212446] handle_irq_event_percpu+0x5c/0x88
[ 35.216883] handle_irq_event+0x48/0x78
[ 35.220712] handle_fasteoi_irq+0xb4/0x188
[ 35.224802] generic_handle_irq+0x24/0x38
[ 35.228804] __handle_domain_irq+0x5c/0xb0
[ 35.232893] gic_handle_irq+0x58/0xa8
[ 35.236548] el1_irq+0xb8/0x180
[ 35.239681] __do_softirq+0x94/0x23c
[ 35.243253] irq_exit+0xd0/0xd8
[ 35.246387] __handle_domain_irq+0x60/0xb0
[ 35.250475] gic_handle_irq+0x58/0xa8
[ 35.254130] el1_irq+0xb8/0x180
[ 35.257268] kernfs_find_ns+0x5c/0x120
[ 35.261010] kernfs_find_and_get_ns+0x3c/0x60
[ 35.265361] sysfs_unmerge_group+0x20/0x68
[ 35.269454] dpm_sysfs_remove+0x2c/0x68
[ 35.273284] device_del+0x80/0x370
[ 35.276683] hid_destroy_device+0x28/0x60
[ 35.280686] usbhid_disconnect+0x4c/0x80
[ 35.284602] usb_unbind_interface+0x6c/0x268
[ 35.288867] device_release_driver_internal+0xe4/0x1b0
[ 35.293998] device_release_driver+0x14/0x20
[ 35.298261] bus_remove_device+0x110/0x128
[ 35.302350] device_del+0x148/0x370
[ 35.305832] usb_disable_device+0x8c/0x1d0
[ 35.309921] usb_disconnect+0xc8/0x2d0
[ 35.313663] hub_event+0x6e0/0x1128
[ 35.317146] process_one_work+0x1e0/0x320
[ 35.321148] worker_thread+0x40/0x450
[ 35.324805] kthread+0x124/0x128
[ 35.328027] ret_from_fork+0x10/0x18
[ 35.331594] handlers:
[ 35.333862] [<0000000079300c1d>] usb_hcd_irq
[ 35.338126] [<0000000079300c1d>] usb_hcd_irq
[ 35.342389] Disabling IRQ #156
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have an explicit HCD_DMA flag, there is not need to override
these methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-5-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is supposed to clear the RH_A_NPS and RH_A_PSM bits, but it's
a no-op because of the & vs | typo. This bug predates git and it was
only discovered using static analysis so it must not affect too many
people in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190817065520.GA29951@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Gemini SoC the FOTG2 stalls after port reset
so restart the HCD after each port reset.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190810150458.817-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UWB and wusbcore code is long obsolete, so let us just move the code
out of the real part of the kernel and into the drivers/staging/
location with plans to remove it entirely in a few releases.
Link: https://lore.kernel.org/r/20190806101509.GA11280@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb core will reset the default control endpoint "ep0" before resetting
a device. if the endpoint has a valid pointer back to the usb device
then the xhci driver reset callback will try to clear the toggle for
the endpoint.
ep0 didn't use to have this pointer set as ep0 was always allocated
by default together with a xhci slot for the usb device. Other endpoints
got their usb device pointer set in xhci_add_endpoint()
This changed with commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
which sets the pointer for any endpoint on a FS/LS device behind a
HS hub that halts, including ep0.
If xHC controller needs to be reset at resume, then all the xhci slots
will be lost. Slots will be reenabled and reallocated at device reset,
but unlike other endpoints the ep0 is reset before device reset, while
the xhci slot may still be invalid, causing NULL pointer dereference.
Fix it by checking that the endpoint has both a usb device pointer and
valid xhci slot before trying to clear the toggle.
This issue was not seen earlier as ep0 didn't use to have a valid usb
device pointer, and other endpoints were only reset after device reset
when xhci slots were properly reenabled.
Reported-by: Bob Gleitsmann <rjgleits@bellsouth.net>
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/1564758044-24748-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is connected to the host controller and
the system enters suspend, the following error happens
in xhci_suspend():
xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout
Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.
Fixes: 435cc1138e ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the past, USB PHY handling has been moved in the HCD core. Some
host controller drivers needing more control of the PHYs, they have
been granted the freedom to handle themselves the PHY states and to
prevent the HCD core to do so in commit 4e88d4c083 ("usb: add a flag
to skip PHY initialization to struct usb_hcd"). With this change, any
USB host controller could set the hcd->skip_phy_initialization flag so
that the HCD core would just skip the PHY initialization sequence.
However, in the USB subsystem, there are currently two entirely
different forms of PHY: one is called 'usb_phy' and is
USB-subsystem-wide, while there is also the generic and kernel-wide
'phy' from the (recent) generic PHY framework.
When the commit above was introduced, both type of PHYs where handled
by the HCD core.
Later, commit bc40f53417 ("USB: core: hcd: drop support for legacy
phys") removed the support for the former type of PHYs in the HCD
core. These 'usb_phy' are still present though, but managed from the
controller drivers only. Hence, setting the
hcd->skip_phy_initialization flag just because a 'usb_phy' is
initialized by a controller driver is a non-sense.
For instance on Armada CP110, a 'usb_phy' is there to enable the power
supply to the USB host, while there is also a COMPHY block providing
SERDES lanes configuration that is referenced as a PHY from the common
PHY framework.
Right now, users of the xhci-plat.c driver either use a 'usb_phy' only
and do not care about the attempt of generic PHY initialization within
the HCD core (as there is none); or they use a single 'phy' and the
code flow does not pass through the block setting
hcd->skip_phy_initialization anyway.
While there is not users of both PHY types at the same time, drop this
limitation from the xhci-plat.c driver. Note that the tegra driver
probably has the same limitation and could definitely benefit from a
similar change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190731121150.2253-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/usb/host/ohci-tmio.c: In function ‘tmio_stop_hc’:
./include/linux/device.h:1499:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/ohci-tmio.c:99:4: note: in expansion of macro ‘dev_err’
dev_err(&dev->dev, "Unsupported amount of ports: %d\n", ohci->num_ports);
^~~~~~~
In file included from drivers/usb/host/ohci-hcd.c:1257:0:
drivers/usb/host/ohci-tmio.c💯3: note: here
case 3:
^~~~
drivers/usb/host/ohci-tmio.c:101:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
pm |= CCR_PM_USBPW3;
^
drivers/usb/host/ohci-tmio.c:102:3: note: here
case 2:
^~~~
drivers/usb/host/ohci-tmio.c:103:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
pm |= CCR_PM_USBPW2;
^
drivers/usb/host/ohci-tmio.c:104:3: note: here
case 1:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190729222201.GA19408@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the code for getting generic PHYs from standard device tree array
from the main controller device node. This is a first step in resolving
the conflict between Exynos EHCI/OHCI sub-nodes and generic USB device
bindings. Later the sub-nodes currently used for assigning PHYs to root
ports of the controller will be removed making a place for the generic
USB device bindings nodes.
Suggested-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190726081453.9456-3-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A second regression was found in the immediate data transfer (IDT)
support which was added to 5.2 kernel
IDT is used to transfer small amounts of data (up to 8 bytes) in the
field normally used for data dma address, thus avoiding dma mapping.
If the data was not already dma mapped, then IDT support assumed data was
in urb->transfer_buffer, and did not take into accound that even
small amounts of data (8 bytes) can be in a scatterlist instead.
This caused a NULL pointer dereference when sg_dma_len() was used
with non-dma mapped data.
Solve this by not using IDT if scatter gather buffer list is used.
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Cc: <stable@vger.kernel.org> # v5.2
Reported-by: Maik Stohn <maik.stohn@seal-one.com>
Tested-by: Maik Stohn <maik.stohn@seal-one.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1564044861-1445-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do extra cpu_to_le32 conversion for
put_unaligned_le32 because it is already implemented
in this function.
Fixes sparse error:
xhci-hub.c:1152:44: warning: incorrect type in argument 1 (different base types)
xhci-hub.c:1152:44: expected unsigned int [usertype] val
xhci-hub.c:1152:44: got restricted __le32 [usertype]
Fixes: 395f540 "xhci: support new USB 3.1 hub request to get extended port status"
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1562501839-26522-1-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715032010.7258-1-huangfq.daxian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header, oxu210hp.h is only included from oxu210hp-hcd.c
so squash it.
When I moved the code, I also fixed the following warnings from
scripts/checkpatch.pl:
drivers/usb/host/oxu210hp-hcd.c:117: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:196: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:221: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:266: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:336: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:354: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:385: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:393: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:429: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:432: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:436: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:451: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:461: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:467: warning: please, no space before tabs
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721144909.5295-2-yamada.masahiro@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct oxu210hp_platform_data is defined, but not used at all.
$ git grep oxu210hp_platform_data
include/linux/oxu210hp.h:struct oxu210hp_platform_data {
include/linux/oxu210hp.h exists just for defining an unused structure,
so it can go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721144909.5295-1-yamada.masahiro@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzboot reported that
https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef
There is not consitency parameter in cluste_id_get/put calling.
In case of getting the id with result is failure, the wusbhc->cluster_id
will not be updated and this can not be used for wusb_cluster_id_put().
Tested report
https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ
Reproduce and gdb got the details:
139 addr = wusb_cluster_id_get();
(gdb) n
140 if (addr == 0)
(gdb) print addr
$1 = 254 '\376'
(gdb) n
142 result = __hwahc_set_cluster_id(hwahc, addr);
(gdb) print result
$2 = -71
(gdb) break wusb_cluster_id_put
Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384.
(gdb) s
Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384
384 id = 0xff - id;
(gdb) n
385 BUG_ON(id >= CLUSTER_IDS);
(gdb) print id
$3 = 255 '\377'
Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_amd_find_chipset_info() is used for chipset detection for
several quirks. It is strange that its return value indicates
the need for the PLL quirk, which means it is often ignored.
This patch adds a function specifically for checking the PLL
quirk like the other ones. Additionally, rename probe_result to
something more appropriate.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-3-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- move the USB special case that bounced DMA through a device
bar into the USB code instead of handling it in the common
DMA code (Laurentiu Tudor and Fredrik Noring)
- don't dip into the global CMA pool for single page allocations
(Nicolin Chen)
- fix a crash when allocating memory for the atomic pool failed
during boot (Florian Fainelli)
- move support for MIPS-style uncached segments to the common
code and use that for MIPS and nios2 (me)
- make support for DMA_ATTR_NON_CONSISTENT and
DMA_ATTR_NO_KERNEL_MAPPING generic (me)
- convert nds32 to the generic remapping allocator (me)
-----BEGIN PGP SIGNATURE-----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=01Fr
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.3' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- move the USB special case that bounced DMA through a device bar into
the USB code instead of handling it in the common DMA code (Laurentiu
Tudor and Fredrik Noring)
- don't dip into the global CMA pool for single page allocations
(Nicolin Chen)
- fix a crash when allocating memory for the atomic pool failed during
boot (Florian Fainelli)
- move support for MIPS-style uncached segments to the common code and
use that for MIPS and nios2 (me)
- make support for DMA_ATTR_NON_CONSISTENT and
DMA_ATTR_NO_KERNEL_MAPPING generic (me)
- convert nds32 to the generic remapping allocator (me)
* tag 'dma-mapping-5.3' of git://git.infradead.org/users/hch/dma-mapping: (29 commits)
dma-mapping: mark dma_alloc_need_uncached as __always_inline
MIPS: only select ARCH_HAS_UNCACHED_SEGMENT for non-coherent platforms
usb: host: Fix excessive alignment restriction for local memory allocations
lib/genalloc.c: Add algorithm, align and zeroed family of DMA allocators
nios2: use the generic uncached segment support in dma-direct
nds32: use the generic remapping allocator for coherent DMA allocations
arc: use the generic remapping allocator for coherent DMA allocations
dma-direct: handle DMA_ATTR_NO_KERNEL_MAPPING in common code
dma-direct: handle DMA_ATTR_NON_CONSISTENT in common code
dma-mapping: add a dma_alloc_need_uncached helper
openrisc: remove the partial DMA_ATTR_NON_CONSISTENT support
arc: remove the partial DMA_ATTR_NON_CONSISTENT support
arm-nommu: remove the partial DMA_ATTR_NON_CONSISTENT support
ARM: dma-mapping: allow larger DMA mask than supported
dma-mapping: truncate dma masks to what dma_addr_t can hold
iommu/dma: Apply dma_{alloc,free}_contiguous functions
dma-remap: Avoid de-referencing NULL atomic_pool
MIPS: use the generic uncached segment support in dma-direct
dma-direct: provide generic support for uncached kernel segments
au1100fb: fix DMA API abuse
...
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-5-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB erratum-A006918 workaround tries to start internal PHY inside
uboot (when PLL fails to lock). However, if the workaround also
fails, then USB initialization is also stopped inside Linux.
Erratum-A006918 workaround failure creates "fsl,erratum_a006918"
node in device-tree. Presence of this node in device-tree is
used to stop USB controller initialization in Linux
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-4-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY_CLK_VALID bit for UTMI PHY in USBDR does not set even
if PHY is providing valid clock. Workaround for this
involves resetting of PHY and check PHY_CLK_VALID bit
multiple times. If PHY_CLK_VALID bit is still not set even
after 5 retries, it would be safe to deaclare that PHY
clock is not available.
This erratum is applicable for USBDR less then ver 2.4.
Signed-off-by: Suresh Gupta <B42813@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-2-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set USB_EN bit to select ULPI phy for USB controller version 2.5
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-1-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PAGE_SHIFT alignment restriction to devm_gen_pool_create() quickly
exhaust local memory because most allocations are much smaller than
PAGE_SIZE. This causes USB device failures such as
usb 1-2.1: reset full-speed USB device number 4 using sm501-usb
sd 1:0:0:0: [sda] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=0x00
sd 1:0:0:0: [sda] tag#0 CDB: opcode=0x28 28 00 00 00 08 7c 00 00 f0 00
print_req_error: I/O error, dev sda, sector 2172 flags 80700
when trying to boot from the SM501 USB controller on SH4 with QEMU.
Align allocations as required but not necessarily much more than that.
The HCCA, TD and ED structures align with 256, 32 and 16 byte memory
boundaries, as specified by the Open HCI[1]. The min_alloc_order argument
to devm_gen_pool_create is now somewhat arbitrarily set to 4 (16 bytes).
Perhaps it could be somewhat lower for general buffer allocations.
Reference:
[1] "Open Host Controller Interface Specification for USB",
release 1.0a, Compaq, Microsoft, National Semiconductor, 1999,
pp. 16, 19, 33.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.
A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree probing to the fotg2 driver.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
[Drop DMA mask coercion, drivers/of/platform.c does the job]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang produces the following warning
drivers/usb/host/xhci-tegra.c:357:27: warning: unused variable
'mbox_cmd_name' [-Wunused-const-variable]
static const char * const mbox_cmd_name[] = {
Looks like it was intended for logging or debugging, but was
never implemented. Removing mbox_cmd_name.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/533
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt
processing for full-/low-speed endpoints connected via a TT, the host
software must use the Clear_TT_Buffer request to the TT to ensure
that the buffer is not in the busy state".
In our case, a full-speed speaker (ConferenceCam) is behind a high-
speed hub (ConferenceCam Connect), sometimes once we get STALL on a
request we may continue to get STALL with the folllowing requests,
like Set_Interface.
Here we invoke usb_hub_clear_tt_buffer() to send Clear_TT_Buffer
request to the hub of the device for the following Set_Interface
requests to the device to get ACK successfully.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Clear_TT_Buffer request sent to the hub includes the address of
the LS/FS child device in wValue field. usb_hub_clear_tt_buffer()
uses udev->devnum to set the address wValue. This won't work for
devices connected to xHC.
For other host controllers udev->devnum is the same as the address of
the usb device, chosen and set by usb core. With xHC the controller
hardware assigns the address, and won't be the same as devnum.
Here we add devaddr in "struct usb_device" for
usb_hub_clear_tt_buffer() to use.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the addition of the local memory allocator, the HCD_LOCAL_MEM
flag can be dropped and the checks against it replaced with a check
for the localmem_pool ptr being initialized.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In preparation for dropping the existing "coherent" dma mem declaration
APIs, replace the current dma_declare_coherent_memory() based mechanism
with the creation of a genalloc pool that will be used in the OHCI
subsystem as replacement for the DMA APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In preparation for dropping the existing "coherent" dma mem declaration
APIs, replace the current dma_declare_coherent_memory() based mechanism
with the creation of a genalloc pool that will be used in the OHCI
subsystem as replacement for the DMA APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For HCs that have local memory, replace the current DMA API usage with
a genalloc generic allocator to manage the mappings for these devices.
To help users, introduce a new HCD API, usb_hcd_setup_local_mem() that
will setup up the genalloc backing up the device local memory. It will
be used in subsequent patches. This is in preparation for dropping
the existing "coherent" dma mem declaration APIs. The current
implementation was relying on a short circuit in the DMA API that in
the end, was acting as an allocator for these type of devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
