Remove those unused ret variables to make it obvious that these function
will not return any errors in the current implementation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure. Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.
This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD Host Controller spec states that the SD Host Controller can
request that the driver send up to 40 CMD19's while doing tuning
and that the total time the card spends responding must be < 150ms.
The sdhci_execute_tuning() function in sdhci.c that loops through
sending the CMD19's has multiple bugs. First it sets a "timeout"
variable to 150 and a loop counter variable to 40. It then decrements
both variables by 1 at the end of each loop. It tries to handle
violations of the count and time by doing a break when BOTH variables
are equal to zero, which can never happen because they we set to
different values and decremented by 1 at the same time. The timeout
variable is not based on time at all and is totally useless.
The routine also considers a loop counter of zero to be an error
which means that any controller that requests the max of 40 CMD19s
will cause tuning to fail and be disabled.
I've fixed these issues by allowing up to 40 CMD19's and I've removed
any attempt to handle the 150ms time limit. Removing timeout checking
seems safe here because each CMD19 is timeout protected and the max
loop counters insures we don't loop forever. Adding timeout checking
would not be as simple as snapping the time at the loop start and
checking for 150ms to pass because the loop queues the CMD19's and
uses events to wait for completion so the time would include
all the normal scheduler latencies.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Track whether preset mode is currently enabled in hardware, and use that
when making decisions elsewhere in the code rather than reading the
register and checking the bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the remaining parts of the power handling in sdhci_do_set_ios()
into sdhci_set_power().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the regulator handling into sdhci_set_power() rather than being in
sdhci_do_set_ios(). This wraps all power control up into this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The only user (sdhci-of-esdhc) no longer uses these callbacks, so lets
remove them to discourage any further use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Clean up the code in sdhci_execute_tuning() so the decision whether
to execute tuning is clearer - and despite this reflecting what the
original code was doing, it shows that it may not be what the author
actually intended.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than reading back the timing information from the registers,
cache it locally. This allows implementations to translate the UHS
timing by overriding the set_uhs_signaling() method as required
without also having to emulate the SDHCI_HOST_CONTROL2 register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method. This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves. This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios(). So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Only one caller to sdhci_set_clock() needs to check whether the
requested clock frequency was the same as the currently set frequency,
yet we work around this in several other sites via sdhci_update_clock().
Rather than doing this, move those checks out into sdhci_do_set_ios(),
which then allows sdhci_update_clock() to be eliminated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than using the streaming API, use the coherent allocator to
provide this memory, thereby eliminating cache flushing of it each
time we map and unmap it. This results in a 7.5% increase in
transfer speed with a UHS-1 card operating in 3.3v mode at a clock
of 49.5MHz.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
On read, we don't need to sync the whole scatterlist and then check
whether any segments need copying - if we check first, we avoid
potentially expensive cache handling.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When we disable card detection interrupts, we should disable both the
insert and remove interrupts irrespective of the current state - this
avoids races between the hardware card detect changing state before
we've read that updated state and altered the interrupt mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Allow SDIO interrupts to be received while the SDHCI host is runtime
suspended. We do this by leaving the AHB clock enabled while the
host is runtime suspended so we can access the SDHCI registers, and
so read and raise the SDIO card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
There's no requirement to have the card tasklet separate now that we
have a threaded interrupt handler, so kill this and move the called
code into the threaded part of the handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use a generic threaded interrupt handler for SDIO interrupt handling,
rather than allowing the SDIO core code to buggily spawn its own
thread. This results in host drivers to be more in control of how
SDIO interrupts are acknowledged in the hardware, rather than having
the internals of the SDIO core placed upon them, possibly resulting
in sub-standard handling.
At least one SDHCI implementation specifies a very specific sequence
to deal with a card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need to change the SDHCI_SDIO_IRQ_ENABLED flag when we're
merely receiving an interrupt - IRQ handling thread in the MMC core
will either re-enable or disable the interrupt via the enable_sdio_irq
callback, which will update this status appropriately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci interrupt handling is a mess; there is a lot of code doing very
similar things. Let's clean this up a bit:
1. set's clear down cmd, data and bus power interrupts in one go - we're
always going to handle these.
2. use a do { } while () loop for looping while there are pending
interrupts.
3. group clearing of bits in intmask into one place.
This results in the code becoming simpler and easier to read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch removes an unneccesary 1ms mdelay in the HS200 tuning
loop, called 40 times per retuning. Currently this causes a latency
of >40ms on any emmc accesses triggering wake from runtime PM,
which can occur for a significant portion of reads on a mostly idle system.
The delay is left in place for SD Cards, which use
MMC_SEND_TUNING_BLOCK rather than MMC_SEND_TUNING_BLOCK_HS200.
I'm not able to find evidence that this is required for SD in the
specs I have access to, however this delay has been present from
initial checkin for SD so I have preserved the original behavior for
compatibility.
This has been verified to fix observed glitching on local audio
playback and recording on apps with inbuilt assumptions on storage
latency.
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When the host->tuning_count is zero it means that the retuning is
disabled. This is checked on the first run of sdhci_execute_tuning()
by the if statement below:
if (!(host->flags & SDHCI_NEEDS_RETUNING) && host->tuning_count &&
(host->tuning_mode == SDHCI_TUNING_MODE_1)) {
So only when tuning_count is non-zero it will set the host flag
SDHCI_USING_RETUNING_TIMER. The else statement is only for re-programming
the timer, which means that flag must be set. Because that is not checked
the else statement is executed in the first run when tuning_count is zero.
This was seen on a host controller which indicated SDHCI_TUNING_MODE_1 (0)
and tuning_count being zero. Suspect that (one of) these registers is not
properly set.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
If the SDHCI irq is shared with another device then the interrupt
handler can get called while SDHCI is runtime suspended. That is
harmless but the warning message is not useful so remove it. Also
returning IRQ_NONE is more appropriate.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.
This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.
Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>
The driver has a timer with a 10 second timeout to catch devices that stop
responding. However it is possible for commands to take even longer than
that. Change the timer timeout to reflect the command timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
In function sdhci_request(), it is possible to do the tuning execution
like below:
sdhci_request() {
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
...
spin_unlock_irqrestore(&host->lock, flags);
<=== Here it is possible one pending finish_tasklet get running
and it will operate the original mrq, and notified the mrq
is done, and causes memory corruption.
sdhci_execute_tuning(mmc, tuning_opcode);
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
...
}
In the above race place, the original mrq should not be finished wrongly,
so here before unlock the spinlock, we need to set the host->mrq to NULL
to avoid this case.
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The auto cmd settings bits should be cleared before sending new commands
or we may receive command timeout error for normal commands due to wrongly
pre-sent auto cmd.
e.g. we receive CMD13 timeout error due to ACMD23 is wrongly enabled
by former data commands.
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2 p3 p4 < p5 p6 p7 >
mmc2: Timeout waiting for hardware interrupt.
mmcblk1boot1: unknown partition table
mmc2: Timeout waiting for hardware interrupt.
mmcblk1boot0: unknown partition table
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ignore Card Interrupt bit in the interrupt status if we already
know that mmc_signal_sdio_irq() is going to be called at the end of
sdhci_irq(). This avoids a needless loop in sdhci_irq() repeatedly
reading interrupt status and doing nothing.
Signed-off-by: Alexey Neyman <stilor@att.net>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The original code missed to report an error when the maximum tuning
loops exhausted or timeout, it will cause the upper layer to wrongly
think the tuning process is passed.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It helps for platform code to use it send tuning commands.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tuning of some platforms may not follow the standard host control
spec v3.0, e.g. Freescale uSDHC on i.MX6Q/DL.
Add a hook here to allow execute platform specific tuning instead of
standard host controller tuning.
The hook only replaces the tuning process, so it's placed after tuning
checking and before the real tuning process.
Some notes for the tuning hook:
1) it needs handle lock itself if it wants to access host controller
according platform specific implementation.
2) do not need to handle runtime pm since it executes with runtime pm
get already.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJSLxu8AAoJEHNBYZ7TNxYMkV8P/RZMkP3L88wPmvdQ4IxVD/Bg
jphPsZTAlY8pLY7EcBVfbIGfBMMoVZ8CayuAbj9u5jFiMBNDUKRnKrky1m95F62n
xXiS5vUiKdWpByMpfKmrqvJr6eS8SWq5z/yug1c3s1Y9T363KgfypgJLvNgbMGiv
qbmjE+Zw65nMwHCk+4Rvq6s4aN6KosRZP0ABsn1foXt3kybSgemp5ShrlEyXohfS
E91EiYxHFC4fdmuWiZZvL1tyHFeV25omyZA90mpkioNItiwoyOM2rfjfEfNq+WBw
UrmdBesbGsF0Zi12CBa9LtzdRjYK8PugBWKW3mycS5++NX9KW6Ac/EpGqFeH9KgL
WZ2v4aQjkbnzQKUB2HcWAyXm88G9MkNvpLbIrmIPtson+q0UjgPYWe5BI3dy/Y1v
YS1JeseslVtSTKzGYsa1GJ7Nc1xYiILRz0RS4YGYXNjwvrl89i2UH7cglYDW36Xd
vxvRBaFpVsj1mfjjITEoG6nE0v5aYH6gSITY79XR+/kN871/99/oIUaWdpjcm9yv
SIYmK7ipcvxugkQ7BoMGbym/dvuUrZ+Vnf8dFlGPTJegZVsnfgrVAnRpvcVwW8+x
4Z79wUPSIETRqj2XX2I/Y0JnrXry+dLLVyeK1tELoeOKev73Ai2lcqPSz6J0tzJs
IErcz0hM1znL2RtgNwio
=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
We use host->ocr_mask to hold the voltage get from device-tree
node, In case host->ocr_mask was available, we use host->ocr_mask
as the final available voltage can be used by MMC/SD/SDIO card.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use regulator_get_optional() to tell the core that requests for regulators
can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Add a card_event callback to sdhci so that clients can provide their
own card_event to be called when card_detect is triggered.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the HC ctrl_2 programming where, in case of
SDR104 and HS200, we have to write 100b in the the UHS Mode
bits. We wrote 101b that is reserved from Arasan Specs.
Reported-by: Youssef Triki <youssef.triki@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
