Use WARN_ON(condition) directly instead of wrapping around an if
condition.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All host drivers using this subdev driver are already converted
to use the control framework so the compatibility ops can be dropped.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified the G2D driver (which initially supported only H/W Rev.3)
to support H/W Rev.4.1 present on Exynos4x12 and Exynos52x0 SOCs.
- Set the SRC and DST type to 'memory' instead of using reset values.
- FIMG2D v4.1 H/W uses different logic for stretching(scaling).
- Use CACHECTL_REG only with FIMG2D v3.
[s.nawrocki: removed empty line at end of file]]
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M
format is half of the Y plane value, rather than having same
bytesperline for all planes.
While at it, simplify the bytesperline parameter handling by
storing it when image format is set and returning those values
when getting the format, instead of recalculating bytesperline
from intermediate parameters.
Reported-by: Sebastian Dröge <sebastian.droege@collabora.co.uk>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed wrong condition in firmware reload function used by the watchdog.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- auto/manual white balance,
- auto/manual gain,
- brightness, saturation, sharpness,
- horizontal/vertical flip,
- color bar test pattern,
- banding filter (power line frequency).
Frame rate can be configured with g/s_frame_interval pad level ops.
Supported resolution are only: SXGA, VGA, QVGA.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2 core helper function that can be used as the subdev
.unsubscribe_event handler. This allows to eliminate some
boilerplate from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead chaneg the passed in format to the pwc default pixelformat.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a bug which causes all histogram regions to start in the
top left corner of the image. The histogram region coordinates are 16 bit
values which share a 32 bit register. The bug is due to the region end
value assignments overwriting the region start values with zero.
Signed-off-by: Johannes Schellen <Johannes.Schellen@rwth-aachen.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kzalloc initializes the memory it allocates to 0, there's no need for an
explicit memset.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The preview engine includes filters that consume columns and lines as
part of their operation, thus resulting in a cropped image. To allow
turning those filters on/off during streaming without affecting the
output image size, the driver adds additional cropping to make the total
number of cropped columns and lines constant regardless of which filters
are enabled.
This process needlessly includes the CFA filter, as whether the filter
is enabled only depends on the sink pad format, which can't change
during streaming.
Exclude the CFA filter from the preview engine margins.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ming Lei reported:
IMO, there is a minor fault in the error handling path of
uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should
have been decreased before usb_autopm_put_interface(). In theory, a [URB
resubmission] warning can be triggered when the device is opened just
between usb_autopm_put_interface() and atomic_dec(&stream->dev->users).
The fix is trivial.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock on the error handling path in function
vpbe_initialize().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be
used uninitialized in this function [-Wuninitialized]
drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here
This is a false positive but the compiler has no way to know about it,
so initialize the variable to 0.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers
these GCC warnings:
drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function]
drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function]
Silence these warnings by wrapping these two functions in an "#ifdef
CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Events for the iMon Knob pad where not correctly interpreted on ARM,
resulting in buggy mouse movements (cursor going straight out of the
screen), key pad only generating KEY_RIGHT and KEY_DOWN events.
A reproducer is:
int main(int argc, char ** argv)
{
char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
return 0;
}
(running on x86 or amd64)
$ ./test
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:-1 @test.c:8
(running on armv6)
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:255 @test.c:8
Forcing the rel_x and rel_y variables as signed char fixes the issue.
Reference: http://www.arm.linux.org.uk/docs/faqs/signedchar.php
Signed-off-by: Alexandre Lissy <alexandrelissy@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vfl_dir field should be set to indicate whether a device can receive
data, output data or can do both. This is used to let the v4l core know
which ioctls should be accepted and which can be refused.
Unfortunately, when this field was added the radio modulator drivers were
not updated: radio modulators transmit and so vfl_dir should be set to
VFL_DIR_TX (or VFL_DIR_M2M in the special case of wl128x).
Because of this omission it is not possible to call g/s_modulator for these
drivers, which effectively renders them useless.
This patch sets the correct vfl_dir value for these drivers, correcting
this bug.
Thanks to Paul Grinberg for bringing this to my attention.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
Here's a long-pending fixes pull request for arm-soc (I didn't send one
in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted to
multiplatform on i.MX, which was causing build failures when included
- Device tree updates for at91 dealing mostly with their new
pinctrl setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YDHs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
Sometimes there is a problem when trying to access the non-existing registers
of the second demodulator path on the STV0903.
This change removes the calls in case the driver is used on a STV0903.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
While there, rename it, as we'll soon introduce a postBER logic
there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add both per-layer and global block error count and block count,
for PER and UCB measurements.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If userspace calls a property that doesn't exist, it currently
just returns -EINVAL. However, this is more likely a problem at
the userspace application, calling it with a non-existing property.
So, add a debug message to help tracking it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Signal/Noise ratio measurement. On this device, a global measure
is taken by the demod. It also provides per-layer CNR measurements,
based on Modulation Error measures (MER).
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do a better job on setting the bit error counters, in order to
have all layer measures to happen in a little less than one
second.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the methods to read bit error/bit count measurements from
mb86a20s. On ISDB-T devices, those reads are done per layer.
However, as userspace applications may not be aware of that,
add a global measure that will sum the bit errors and bit
counts for each layer, storing them into a global value.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of providing separate callbacks to read the several FE
stats properties, the better seems to use just one method that will:
- Read lock status;
- Read signal strength;
- if locked, get TMCC data;
- if locked, get DVB statistics.
As the DVB frontend thread will call this read_status callback
on every 3 seconds, and userspace can even call it earlier,
all stats data and layers layout will be updated together if
available, with is a good thing.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the logic to poll, reset counters and report the QoS stats
to the end user.
The idea is that the core will periodically poll the frontend for
the stats. The frontend may return -EBUSY, if the previous collect
didn't finish, or it may fill the cached data.
The value returned to the end user is always the cached data.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Feng's kbuild test:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: potential null dereference 'state'. (kzalloc returns null)
Date: Wed, 23 Jan 2013 19:30:43 +0800
commit: f66d81b54d [media] mb86a20s: convert it to use dev_info/dev_err/dev_dbg
drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: potential null dereference 'state'. (kzalloc returns null)
drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: we previously assumed 'state' could be null (see line 705)
As, at mb86a20s_attach(), we have an i2c pointer, use it for all printk
messages there, instead of state->i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the cam_mclk rate changes are back-propagated to dpll4_m5_ck we
can set the cam_mclk rate directly instead of manually setting the rate
of the parent clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Instead of having its own set of macros, use the Kernel default
ones for debug, error and info.
While here, do some cleanup on the debug printk's.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reorder functions to have everything related to stats/status read
close. That will make the file more organized as other stats
routines will be added.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split the logic that reads the status from the DVB callback. That
helps to properly return an error code, if status read fails.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The read/write errors are not handled well on get_frontend. Fix it,
by letting the frontend cached values to represent the DVB properties
that were successfully retrieved.
While here, use "c" for dtv_frontend_properties cache, instead of
"p", as this is more common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This contains a single compilation fix for the CODA driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7H1R
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer:
ARM i.MX fixes for -rc.
This contains a single compilation fix for the CODA driver.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
[media] coda: Fix build due to iram.h rename
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: Tomasz Stanislawski <t.stanislaws@samsung.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: Sylwester Nawrocki <s.nawrocki@samsung.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mike Isely <isely@pobox.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-By: Mike Isely <isely@pobox.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.
The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:
1. Some drivers are using custom omap_dm_timer calls
There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.
2. Hardware OMAP4_ERRATA_I688 needs to be fixed up
This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.
3. Legacy header needed for omap-sham.c
Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.
4. Mailbox is waiting to get moved to drivers
Disable it for now to avoid adding a dependency to the
mailbox patches.
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The uvc_set_ctrl() calls don't write to the hardware. A failure at that
point thus leaves the device in a clean state, with no control modified.
Set the error_idx field to the count value to reflect that, as per the
V4L2 specification.
TRY_EXT_CTRLS is unchanged and the error_idx field must always be set to
the failed control index in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit ba68c8530a263dc4de440fa10bb20a1c5b9d4ff5 (Partly revert "[media]
uvcvideo: Set error_idx properly for extended controls API failures")
also reverted part of commit 30ecb936cb
("uvcvideo: Return -EACCES when trying to access a read/write-only
control") by mistake. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi Mauro,
After merging the v4l-dvb tree, today's linux-next build (x86_64
allmodconfig) failed like this:
drivers/media/platform/sh_veu.c:1146:22: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_veu_probe'
drivers/media/platform/sh_veu.c:1228:22: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_veu_remove'
drivers/media/platform/sh_veu.c:1244:2: error: implicit declaration of function '__devexit_p' [-Werror=implicit-function-declaration]
drivers/media/platform/sh_veu.c:1244:25: error: 'sh_veu_remove' undeclared here (not in a function)
drivers/media/platform/sh_veu.c: In function 'sh_veu_init':
drivers/media/platform/sh_veu.c:1253:45: error: 'sh_veu_probe' undeclared (first use in this function)
drivers/media/platform/sh_veu.c:1253:45: note: each undeclared identifier is reported only once for each function it appears in
drivers/media/platform/sh_veu.c: At top level:
drivers/media/platform/sh_veu.c:1095:20: warning: 'sh_veu_bh' defined but not used [-Wunused-function]
drivers/media/platform/sh_veu.c:1109:20: warning: 'sh_veu_isr' defined but not used [-Wunused-function]
drivers/media/platform/sh_veu.c: In function 'sh_veu_init':
drivers/media/platform/sh_veu.c:1254:1: warning: control reaches end of non-void function [-Wreturn-type]
Caused by commit 05efa71bdc ("[media] media: add a VEU MEM2MEM format
conversion and scaling driver") interacting with commit 54b956b903
("Remove __dev* markings from init.h") from the driver-core.current tree.
I have applied the following merge fix patch which could be applied
directly to the v4l-dvb tree (please):
CONFIG_HOTPLUG is always true now and the __dev* macros have meen removed.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit c045e3f13 (ARM: imx: include iram.h rather than mach/iram.h) changed the
location of iram.h, which causes the following build error when building the coda
driver:
drivers/media/platform/coda.c:27:23: error: mach/iram.h: No such file or directory
drivers/media/platform/coda.c: In function 'coda_probe':
drivers/media/platform/coda.c:2000: error: implicit declaration of function 'iram_alloc'
drivers/media/platform/coda.c:2001: warning: assignment makes pointer from integer without a cast
drivers/media/platform/coda.c: In function 'coda_remove':
drivers/media/platform/coda.c:2024: error: implicit declaration of function 'iram_free'
Since the content of iram.h is not imx specific, move it to
include/linux/platform_data/imx-iram.h instead. This is an intermediate solution
until the i.MX iram allocator is converted to the generic SRAM allocator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The plat/*.h headers are not available to drivers in multiplatform
kernels. As the header isn't needed, just remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multistream support for stv0900. For Netup Dual S2 CI with STV0900BAC/AAC.
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Walking rbtree while it's modified is a Bad Idea(tm); besides,
the result of find_vma() can be freed just as it's getting returned
to caller. Fortunately, it's easy to fix - just take ->mmap_sem a bit
earlier (and don't bother with find_vma() at all if virtp >= PAGE_OFFSET -
in that case we don't even look at its result).
While we are at it, what prevents VIDIOC_PREPARE_BUF calling
v4l_prepare_buf() -> (e.g) vb2_ioctl_prepare_buf() -> vb2_prepare_buf() ->
__buf_prepare() -> __qbuf_userptr() -> vb2_vmalloc_get_userptr() -> find_vma(),
AFAICS without having taken ->mmap_sem anywhere in process? The code flow
is bloody convoluted and depends on a bunch of things done by initialization,
so I certainly might've missed something...
Cc: stable@vger.kernel.org [2.6.35]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <archit@ti.com>
Cc: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore ds3000.c read_signal_strength.
Call tuner get_rf_strength from frontend read_signal_strength.
We are able to do a NULL check and doesn't limit the tuner
attach to the frontend attach area.
At the moment the lmedm04 tuner attach is stuck in frontend
attach area.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a configuration option for v4l2-int-device so it is only compiled when
necessary, which is only by omap24xxcam and tcm825x drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remy Blank reported that audio over USB can be made working for the television
input if .amux is changed from EM28XX_AMUX_LINE_IN to EM28XX_AMUX_VIDEO.
An examination of his devices shows, that it is indeed supplied with an EM202
AC97 audio IC. We also use this setting for the Cinergy 200.
Remy Blank also provided the original version of this patch (many thanks !).
Fixes bug 14126 (see bug report for further device details).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We recently pushed the locking down into this function, but there was
an error path where the unlock was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mutex_lock_interruptible is used on paths where a signal can be
pending, the device is not closed properly and cannot be reused.
This usually happens when you start tzap for example and send it a
TERM signal. The signal is pending while tear-down routines are
called. Hence streaming is not properly stopped in that case. And
the device stops working from that moment on.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Device with ID 1b80:d393 is the Gigabyte U7300 DVB-T dongle.
It contains decoder Realtek RTL2832U and tuner Fitipower FC0012.
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alexander Inyukhin <shurick@sectorb.msk.ru>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use own flag to mark when rc polling is active/deactive and make
decisions, like start/stop polling on suspend/resume, against that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I think it is better (cheaper) to use dummy defines for functions
that has no meaning when remote controller is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those are not needed anymore as all dvb-usb-v2 drivers has proper
dependency checks for RC-core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it possible to compile dvb_usb_v2 driver without the remote
controller (RC-core).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been over 3 years since the V4L2_CID_[HV]CENTER were deprecated.
Clean up the DocBook and remove the V4L2_CID_VCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED control related paragraphs.
Remove the V4L2_CID_[HV]CENTER controls definitions from v4l2-controls.h,
these controls are not used by any driver in the mainline now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change internal buffer allocation from vb2 memory ops call to direct
calls of dma_alloc_coherent. This change shortens the code and makes it
much more readable.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move firmware allocation from open to probe to avoid problems
when using CMA for allocation. In certain circumstances CMA may allocate
buffer that is not in the beginning of the MFC memory area.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Checking unsigned variable for negative value always returns false.
Hence make this value signed as we expect it to be negative too.
Fixes the following smatch warning:
drivers/media/platform/s5p-mfc/s5p_mfc_opr_v6.c:572
s5p_mfc_set_enc_ref_buffer_v6() warn: unsigned 'buf_size1' is never
less than zero.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Flushing of delay DPB buffers have to be done during stream off.
In MFC v6, it is done with a risc to host command.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variable index is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch will add the device tree support for MFC driver.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following checkpatch warnings:
WARNING: sizeof *fmt should be sizeof(*fmt)
WARNING: sizeof *res should be sizeof(*res)
WARNING: sizeof *res should be sizeof(*res)
WARNING: sizeof sd->name should be sizeof(sd->name)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use proper return value test for clk_get() and devm_regulator_get()
functions and propagate any errors from the clock and the regulator
subsystem to the driver core. In two cases a proper error code is
now returned rather than 0.
Reported-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch patch eliminates potential AB-BA deadlock when one process calls
open(), or VIDIOC_S/TRY_FMT ioctl on the FIMC capture video node, while
other thread is reconfiguring media links via media device node:
/dev/video? open() /dev/media? MEDIA_IOC_SETUP_LINK ioctl
mutex_lock(video_lock) mutex_lock(graph_lock)
fimc_pipeline_open() fimc_md_link_notify()
mutex_lock(graph_lock) mutex_lock(video_lock)
... ...
The deadlock is avoided by always taking the graph mutex first in video
node open() or an ioctl, before the video lock is acquired. Reversed
order seems impossible, since media device driver's link_notify callback
is called with media graph mutex already held.
To ensure proper locking order VIDIOC_S_FMT and VIDIOC_TRY_FMT ioctls are
not serialized in the v4l2-core and the driver takes care of it itself.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the hard coded csi_sensors[] array size with a relevant
constant to make sure we don't iterate beyond the actual array.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes following issue found with a static analysis tool:
Pointer 'ffmt' returned from call to function 'fimc_capture_try_format'
at line 1522 may be NULL and may be dereferenced at line 1535.
Although it shouldn't happen in practice, add the NULL pointer check
to be on the safe side.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New context states were added but handling in s5p_mfc_handle_error for
these states was not. After this patch these states are be handled
correctly.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure 'ret' is not used uninitialized.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check of return value from __find_format() was inverted
by mistake. This patch fixes regression introduced in commit
5565a2ad47 [media] m5mols: Protect driver data with a mutex
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Single-planar V4L2 buffers are converted to multi-planar vb2 buffers
with a single plane when queued. The plane data_offset field is not
available in the single-planar API and must be set to 0 for all output
buffers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to keep dummy sleep() callback implementation as
DVB-core checks existence of it before calls callback. Due to that
we can remove it.
FC0012 is based of direct-conversion receiver architecture
(aka Zero-IF) where is no IF used. Due to that IF is always 0 Hz.
Fix comment to point that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to copy config to the driver state. Those are coming from
the const struct and could be used directly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That adds support for AF9035 dual devices having FC0012 tuners.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need feed clock to slave demodulator at the very beginning
in case of dual tuner configuration.
I am not sure if that configuration changes clock output divider
or enable clock output itself...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need even more configuration options and overloading dvb_attach()
for all those sounds quite stupid. Due to that switch struct and make
room for new options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various small changes and fixes releated to dual mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that it uses videobuf2, em28xx can support DMABUF.
Tested with an HVR-950 on analog mode and a 2gen i5core machine
with an i915 graphics adapter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The above commit were applied only partially; it broke tuner and
demod attach, but the part that added it to ngene_info was missing.
Not sure what happened there, but, without this patch, a regression
would be happening.
Also, gcc complains about a defined but not used symbol.
So, apply manually the missing part.
Cc: Patrice Chotard <patricechotard@free.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converting it to platform code can make the code smaller.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After removing i.mx25 support and buf_cleanup() callback,
buffer states are not used in the code any longer.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All necessary tasks to end the streaming properly are
already implemented in mx2_stop_streaming() and nothing
remains to be done in this callback.
Furthermore, it only included debug messages so it can
be removed.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i.MX25 support has been broken for several releases
now and nobody seems to care about it.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: rebased on top of cpu_is_mx27() removal]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct soc_camera_link currently contains fields, used both by sensor and
bridge drivers. To make subdevice driver re-use simpler, split it into a
host and a subdevice parts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera has a per-device node lock, used for video operations
and a per-host lock for code paths, modifying host's pipeline. Manipulating
the two locks increases complexity and doesn't bring any advantages. This
patch removes the per-device lock and uses the per-host lock for all
operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently devm_regulator_bulk_get() is called by soc-camera during host
driver probing, but regulators are attached to the camera platform
device, that is staying, independent whether the host probed successfully
or not. This can lead to repeated regulator requesting, if the host
driver is re-probed. Move the call to platform device probing to avoid
this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The recently introduced host_lock causes lockdep warnings, besides, list
enumeration in scan_add_host() must be protected by holdint the list_lock.
OTOH, holding .video_lock in soc_camera_open() isn't enough to protect
the host during its building of the pipeline, because .video_lock is per
soc-camera device. If, e.g. more than one sensor can be attached to a host
and the user tries to open both device nodes simultaneously, host's .add()
method can be called simultaneously for both sensors. Fix these problems
by holding list_lock instead of .host_lock in scan_add_host() and taking
it shortly at the beginning of soc_camera_open(), and using .host_lock to
protect host's .add() and .remove() operations only.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dereference to 'icl' should be moved below the NULL test.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That fixes the following warning:
drivers/media/usb/em28xx/em28xx-video.c:611:5: warning: no previous prototype for 'em28xx_stop_streaming' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When subdev registration fails the subdev v4l2_dev field is left to a
non-NULL value. Later calls to v4l2_device_unregister_subdev() will
consider the subdev as registered and will module_put() the subdev
module without any matching module_get().
Fix this by setting the subdev v4l2_dev field to NULL in
v4l2_device_register_subdev() when the function fails.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
EEPROMs are currently read in blocks of 16 bytes, but the em2800 is limited
to 4 bytes per read. All other chip variants support reading of max. 64 bytes
at once (according to the em258x datasheet; also verified with em2710, em2882,
and em28174).
Since em2800_i2c_recv_bytes() has been fixed to return with -EOPNOTSUPP when
more than 4 bytes are requested, EEPROM reading with this chip is broken.
It was actually broken before that change, too, it just didn't throw an error
because the i2c adapter silently returned trash data (for all reads >1 byte !).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- do not pass USB specific error codes to userspace/i2c-subsystem
- unify the returned error codes and make them compliant with
the i2c subsystem spec
- check number of actually transferred bytes (via USB) everywehere
- fix/improve debug messages
- improve code comments
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_FUNC_SMBUS_EMUL includes flag I2C_FUNC_SMBUS_WRITE_BLOCK_DATA which signals
that up to 31 data bytes can be written to the ic2 client.
But the EM2800 supports only i2c messages with max. 4 data bytes.
I2C_FUNC_IC2 should be set if a master_xfer function pointer is provided in
struct i2c_algorithm.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function em2800_i2c_recv_bytes() has 2 severe bugs:
1) It does not wait for the i2c read to complete before reading the received message content from the bridge registers.
2) Reading more than 1 byte doesn't work
The former can result in data corruption, the latter always does.
The rewritten code also superseds the content of function
em2800_i2c_check_for_device().
Tested with device "Terratec Cinergy 200 USB".
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em2800 can transfer up to 4 bytes per i2c message.
All other em25xx/em27xx/28xx chips can transfer at least 64 bytes per message.
I2C adapters should never split messages transferred via the I2C subsystem
into multiple message transfers, because the result will almost always NOT be
the same as when the whole data is transferred to the I2C client in a single
message.
If the message size exceeds the capabilities of the I2C adapter, -EOPNOTSUPP
should be returned.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_key functions are independent from the selected protocol, so assign
them once only at device initialization.
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main purpose of this patch is to move the call of em28xx_release_resources()
after the call of em28xx_close_extension().
This is necessary, because some resources might be needed/used by the extensions
fini() functions when they get closed.
Also mark the device as disconnected earlier in this function and unify the
em28xx_uninit_usb_xfer() calls for analog and digital mode.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DEV_INITIALIZED of enum em28xx_dev_state state is used nowhere and there is no
need for DEV_MISCONFIGURED, so remove this enum and use a boolean field
'disconnected' in the device struct instead.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the em28xx driver over to videobuf2. It is
likely that em28xx_fh can go away entirely, but that will come in
a separate patch.
[mchehab@redhat.com: fix a non-trivial merge conflict with some VBI
patches; CodingStyle fixes]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sliced VBI support in the tvp5150 is completely broken. And there is no
support for the saa7115 sliced VBI implementation in the em28xx driver. So
we remove the sliced VBI support completely.
It should be possible to get it to work with the tvp5150, but that will
require someone to really dig into that driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When in webcam mode the STD API shouldn't be implemented.
When changing the standard the resolution wasn't updated, and there was no
check against streaming-in-progress.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No longer needed now that em28xx has been converted to the control framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
g/s_parm should fill in readbuffers.
For non-webcams s_parm should return -ENOTTY instead of -EINVAL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes platform/bridge drivers need to be notified when a control from
a sub-device changes value. In order to support this a notify callback was
added.
[dheitmueller@kernellabs.com: fix merge conflict in v4l2-ctrls.c]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-compliance found problems with frequency clamping that wasn't
reported correctly and missing tuner index checks.
Also removed unnecessary tuner type checks (these are now done by the
v4l2 core).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Radio devices should not implement those ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-i2c-kbd already adds I2C IR before the name. The way it is,
the devices are named as:
"i2c IR (i2c IR (EM2840 Hauppaug"
With is ugly and incorrect. After this patch, it is now properly
displayed as:
"i2c IR (WinTV USB2)"
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the device has an I2C IR, em28xx-rc should be loaded by default,
except if the user explicitly requested to not load, via modprobe
option.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx-input is used by 3 different types of input devices:
- devices with buttons (like cameras and grabber devices);
- devices with I2C remotes;
- em2860 or latter chips with RC support embedded.
When the device has an I2C remote, all it needs to do is to call
the proper I2C driver (ir-i2c-kbd), passing the proper data to
it, and just leave the code.
Also, button devices have its own init code that doesn't depend on
having an IR or not (as a general rule, they don't have).
So, move its init code to fix bugs introduced by earlier patches
that prevent them to work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
