Make sure @fw_offset field of struct fw_mac is more than the size
of struct fw_mac.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The struct fw_type_1 is used by MAC only, so rename it to a meaningful one.
Besides, adjust two messages. Replace "load xxx fail" with "check xxx fail"
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2019-10-21
This series contains updates to e1000e and igc only.
Sasha adds stream control transmission protocol (SCTP) CRC checksum
support for igc. Also added S0ix support to the e1000e driver. Then
added multicast support by adding the address list to the MTA table and
providing the option for IPv6 address for igc. In addition, added
receive checksum support to igc as well. Lastly, cleaned up some code
that was not fully implemented yet for the VLAN filter table array.
v2: Dropped patch 1 & 2 from the original series. Patch 1 is being sent
to 'net' tree as a fix and patch 2 implementation needs to be
re-worked. Updated the patch to add support for S0ix to fix the
reverse Xmas tree issues and made the entry/exit functions void
since they constantly returned success. All based on community
feedback.
v3: Cleaned up patch 4 of the series based on feedback from the
community. Cleaned up a stray comma in a code comment and removed
the 'inline' of a function that would be inlined by the compiler
anyways.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use tcf_tm_dump(), instead of an open coded variant (no functional change
in this patch).
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: marvell: support downshift as PHY tunable
So far downshift is implemented for one small use case only and can't
be controlled from userspace. So let's implement this feature properly
as a PHY tunable so that it can be controlled via ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of superseded function marvell_set_downshift() we can use new
function m88e1111_set_downshift() in m88e1116r_config_init().
For this m88e1116r_config_init() has to be moved in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far downshift is implemented for one small use case only and can't
be controlled from userspace. So let's implement this feature properly
as a PHY tunable so that it can be controlled via ethtool.
More Marvell PHY's may support downshift, but I restricted it for now
to the ones where I have the datasheet.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added test cases for IP header operations:
- set tos/precedence
- add value to tos/precedence
- clear tos/precedence
- invert tos/precedence
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi says:
====================
add XDP support to mvneta driver
Add XDP support to mvneta driver for devices that rely on software
buffer management. Supported verdicts are:
- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_TX
Moreover set ndo_xdp_xmit net_device_ops function pointer in order
to support redirecting from other device (e.g. virtio-net).
Convert mvneta driver to page_pool API.
This series is based on previous work done by Jesper and Ilias.
We will send follow-up patches to reduce DMA-sync operations.
Changes since v4:
- reset page_pool pointer to NULL in mvneta_rxq_drop_pkts and in
mvneta_create_page_pool error path
- move dma sync in mvneta_rx_refill() in patch 2/7
- verify bpf prog pointer in mvneta_xdp_setup to double-check if
stop/start is really necessary
- coding style fixes
Changes since v3:
- rename MVNETA_XDP_CONSUMED in MVNETA_XDP_DROPPED
- squash patch 4/8 and patch 3/8
- fix dma sync for XDP_TX verdict
- fix queue_index in xdp_rxq_info_reg
- cosmetics
Changes since v2:
- rely on page_pool_recycle_direct instead of xdp_return_buff for XDP_DROP
- define xdp buffer in mvneta_rx_swbm and avoid default initializations
- use dma_sync_single_for_cpu instead of dma_sync_single_range_for_cpu
- run page_pool_release_page in mvneta_swbm_add_rx_fragment even if
the buffer contains just ETH_FCS
Changes since v1:
- sync dma buffers before refilling hw queues
- fix stats accounting
Changes since RFC:
- implement XDP_TX
- make tx pending buffer list agnostic
- code refactoring
- check if device is running in mvneta_xdp_setup
====================
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement XDP_TX verdict and ndo_xdp_xmit net_device_ops function
pointer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow tx buffer array to contain both skb and xdp buffers in order to
enable xdp frame recycling adding XDP_TX verdict support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move data buffer prefetch in mvneta_swbm_rx_frame after
dma_sync_single_range_for_cpu
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mvneta_rx_swbm code introducing mvneta_swbm_rx_frame and
mvneta_swbm_add_rx_fragment routines. Rely on build_skb in oreder to
allocate skb since the previous patch introduced buffer recycling using
the page_pool API.
This patch fixes even an issue in the original driver where dma buffers
are accessed before dma sync.
mvneta driver can run on not cache coherent devices so it is
necessary to sync DMA buffers before sending them to the device
in order to avoid memory corruptions. Running perf analysis we can
see a performance cost associated with this DMA-sync (anyway it is
already there in the original driver code). In follow up patches we
will add more logic to reduce DMA-sync as much as possible.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the page_pool api for allocations and DMA handling instead of
__dev_alloc_page()/dma_map_page() and free_page()/dma_unmap_page().
Pages are unmapped using page_pool_release_page before packets
go into the network stack.
The page_pool API offers buffer recycling capabilities for XDP but
allocates one page per packet, unless the driver splits and manages
the allocated page.
This is a preliminary patch to add XDP support to mvneta driver
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mvneta_update_stats routine to collect {rx/tx} statistics
(packets and bytes). This is a preliminary patch to add XDP support to
mvneta driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filter table array not implemented yet and shadow_vfta pointer
not used. Clean up the code and remove the unused shadow_vfta pointer.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Extend the socket buffer field process and add Rx checksum functionality
Minor: fix indentation with tab instead of spaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add multicast addresses list to the MTA table.
Implement basic Rx mode support.
Add option for IPv6 address settings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement flow for S0ix support. Modern SoCs support S0ix low power
states during idle periods, which are sub-states of ACPI S0 that increase
power saving while supporting an instant-on experience for providing
lower latency that ACPI S0. The S0ix states shut off parts of the SoC
when they are not in use, while still maintaning optimal performance.
This patch add support for S0ix started from an Ice Lake platform.
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Huazhong Tan says:
====================
net: hns3: add some cleanups & optimizations
This patchset includes some cleanups and optimizations for the HNS3
ethernet driver.
[patch 1/8] removes unused and unnecessary structures.
[patch 2/8] uses a ETH_ALEN u8 array to replace two mac_addr_*
field in struct hclge_mac_mgr_tbl_entry_cmd.
[patch 3/8] optimizes the barrier used in the IO path.
[patch 4/8] introduces macro ring_to_netdev() to get netdevive
from struct hns3_enet_ring variable.
[patch 5/8] makes struct hns3_enet_ring to be cacheline aligned
[patch 6/8] adds a minor cleanup for hns3_handle_rx_bd().
[patch 7/8] removes linear data allocating for fraglist SKB.
[patch 8/8] clears hardware error when resetting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is resetting, the CMDQ service may be stopped until
reset completed. If a new RAS error occurs at this moment, it
will no be able to clear the RAS source. This patch fixes it
by clear the RAS source after reset complete.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, napi_alloc_skb() is used to allocate skb for fraglist
when the head skb is not enough to hold the remaining data, and
the remaining data is added to the frags part of the fraglist skb,
leaving the linear part unused.
So this patch passes length of 0 to allocate fraglist skb with
zero size of linear data.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e559709505 ("net: hns3: Add handling of GRO Pkts
not fully RX'ed in NAPI poll"), ring->skb is used to record the
current SKB when processing the RX BD in hns3_handle_rx_bd(),
so the parameter out_skb is unnecessary.
This patch also adjusts the err checking to reduce duplication
in hns3_handle_rx_bd(), and "err == -ENXIO" is rare case, so put
it in the unlikely annotation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since struct hns3_enet_ring is a frequently used in critical data
path, so make it cacheline aligned as struct hns3_enet_tqp_vector.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few places that need to access the netdev of a ring
through ring->tqp->handle->kinfo.netdev, and ring->tqp is a struct
which both in enet and hclge modules, it is better to use the
struct that is only used in enet module.
This patch adds the ring_to_netdev() to access the netdev of ring
through ring->tqp_vector->napi.dev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the TX and RX ring in a queue is bounded to the
same IRQ, there may be unnecessary barrier op when only one of
the ring need to be processed.
This patch adjusts the location of rmb() in hns3_clean_tx_ring()
and adds a checking in hns3_clean_rx_ring() to avoid unnecessary
barrier op when there is nothing to do for the ring.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_addr_hi32 and mac_addr_lo16 are used to store the MAC address
for management table. But using array of mac_addr[ETH_ALEN] would
be more general and not need to care about the big-endian mode of
the CPU.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the queue_index field in struct hns3_nic_ring_data is
used, other field is unused and unnecessary for hns3 driver,
so this patch removes it and move the queue_index field to
hns3_enet_ring.
This patch also removes an unused struct hns_queue declaration.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RPi 4 uses the hardware handshake lines for CYW43455, but the chip
doesn't react to HCI requests during DT probe. The reason is the inproper
handling of the RTS line during startup. According to the startup
signaling sequence in the CYW43455 datasheet, the hosts RTS line must
be driven after BT_REG_ON and BT_HOST_WAKE.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit cde9dde6e1.
The frame reassembly errors were root caused to a transient gpio issue.
The missing response was root caused to an issue with properly managing
RFR in the uart driver. Addressing those root causes occurs outside of
hci_qca and eliminates the need for the 50ms delay, so remove it.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andrii Nakryiko says:
====================
This patch set's main goal is to teach bpf_object__open() (and its variants)
to automatically derive BPF program type/expected attach type from section
names, similarly to how bpf_prog_load() was doing it. This significantly
improves user experience by eliminating yet another
obvious-only-in-the-hindsight surprise, when using libbpf APIs.
There are a bunch of auxiliary clean-ups and improvements. E.g.,
bpf_program__get_type() and bpf_program__get_expected_attach_type() are added
for completeness and symmetry with corresponding setter APIs. Some clean up
and fixes in selftests/bpf are done as well.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Now that libbpf can correctly guess BPF program types from section
names, remove a bunch of explicit bpf_program__set_type() calls
throughout tests.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191021033902.3856966-8-andriin@fb.com
reference_tracking is actually a set of 9 sub-tests. Make it explicitly so.
Also, add explicit "classifier/" prefix to BPF program section names to
let libbpf correctly guess program type. Thus, also remove explicit
bpf_prog__set_type() call.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191021033902.3856966-7-andriin@fb.com
test_progs never created a copy of subtest name, rather just stored
pointer to whatever string test provided. This is bad as that string
might be freed or modified by the end of subtest. Fix this by creating
a copy of given subtest name when subtest starts.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191021033902.3856966-6-andriin@fb.com
Teach bpf_object__open how to guess program type and expected attach
type from section names, similar to what bpf_prog_load() does. This
seems like a really useful features and an oversight to not have this
done during bpf_object_open(). To preserver backwards compatible
behavior of bpf_prog_load(), its attr->prog_type is treated as an
override of bpf_object__open() decisions, if attr->prog_type is not
UNSPECIFIED.
There is a slight difference in behavior for bpf_prog_load().
Previously, if bpf_prog_load() was loading BPF object with more than one
program, first program's guessed program type and expected attach type
would determine corresponding attributes of all the subsequent program
types, even if their sections names suggest otherwise. That seems like
a rather dubious behavior and with this change it will behave more
sanely: each program's type is determined individually, unless they are
forced to uniformity through attr->prog_type.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191021033902.3856966-5-andriin@fb.com
Map uprobe/uretprobe into KPROBE program type. tp/raw_tp are just an
alias for more verbose tracepoint/raw_tracepoint, respectively.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191021033902.3856966-4-andriin@fb.com
There are bpf_program__set_type() and
bpf_program__set_expected_attach_type(), but no corresponding getters,
which seems rather incomplete. Fix this.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191021033902.3856966-3-andriin@fb.com
For kernel logging macros, pr_warning() is completely removed and
replaced by pr_warn(). By using pr_warn() in tools/lib/bpf/ for
symmetry to kernel logging macros, we could eventually drop the
use of pr_warning() in the whole kernel tree.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191021055532.185245-1-wangkefeng.wang@huawei.com
Don't generate a broken bpf_helper_defs.h header if the helper script needs
updating because it doesn't recognize a newly added type. Instead print an
error that explains why the build is failing, clean up the partially
generated header and stop.
v1->v2:
- Switched from temporary file to .DELETE_ON_ERROR.
Fixes: 456a513bb5 ("scripts/bpf: Emit an #error directive known types list needs updating")
Suggested-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191020112344.19395-1-jakub@cloudflare.com
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.
Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)
So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.
We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.
We move in the first cache line fields that can be
dirtied often.
We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.
Fixes: 355b985537 ("netns: provide pure entropy for net_hash_mix()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam. Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: netem: fix further issues with packet corruption
This set is fixing two more issues with the netem packet corruption.
First patch (which was previously posted) avoids NULL pointer dereference
if the first frame gets freed due to allocation or checksum failure.
v2 improves the clarity of the code a little as requested by Cong.
Second patch ensures we don't return SUCCESS if the frame was in fact
dropped. Thanks to this commit message for patch 1 no longer needs the
"this will still break with a single-frame failure" disclaimer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.
Fixes: 6071bd1aa1 ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
