since the pads array is of known small size, there is no reason to
allocate it separately. Instead, it is embedded in the entity struct.
This also conforms to the media controller doc:
'Most drivers will embed the pads array in a driver-specific structure,
avoiding dynamic allocation.'
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
[hverkuil-cisco@xs4all.nl: remove unused vimc_pads_init()]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
the struct vimc_platform_data is not used anymore and can be removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'vimc_pipeline_s_stream' is not used and can be
removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc is a single kernel module and does not need to
export any symbols therefore there is no need for these
declarations.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since this function only calls v4l2_device_unregister_subdev,
it is pointless.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
according to the docs, this function must be called during
the cleanup phase after unregistering the entity.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc_sen_add function first registers the subdevice and then
calls tpg_alloc. If tpg_alloc fails it unregisters the subdevice
and then frees vsen, this cause double free since the release
callback that follows subdevice unregistration also frees vsen.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the add callback returns NULL on failure and the array
is initialized to NULLs, there is no need for the intermediate
assignment to local var.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since NULL value for vimc entity pointer indicates
that entity creation failed and this is tested, the
pointers should be initialized to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch corrects the SPDX License Identifier style
in header file related to media Drivers for Analog TV Tuners.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename the confusingly named smiapp_update_mode() function as
smiapp_pll_blanking_update(). The function is used to calculate new PLL
and blanking configuration after binning or scaling configuration has been
changed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Earlier it was possible that the parts of the driver that assumed runtime
PM was enabled were being called before runtime PM was enabled in the
driver's probe function. So enable runtime PM before registering the
sub-device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use non-binned limits when binning is disabled and binned when they're
enabled.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor configuration since it was previously powered off was not
changed, so no need to update the PLL configuration etc. What is necessary
though is to re-apply the configuration to the sensor's registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only write the binning configuration at stream start. It has no effect
otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver implementation assumed the binning limits could change
dynamically based on the binning configuration. This is not actually the
case; these limits are static and suitable to be used with all binning
configurations but possibly not optimal limit for many of those
configurations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Destroy the mutex initialised by the driver in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The interface supports probing for the NVM size but this was not
implemented in the driver. Do that now.
This will also make nokia,nvm-size property redundant.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only some devices require polling for NVM ready. Do the polling only on
devices that need it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The data transfer capability register was defined but its bits were not.
Do that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Split out reading a single NVM page into a separate function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If NVM reading failed, the device was left powered on. Fix that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The BIT macro is a better way to define register bits, for 1 << bit is
risky for 32-bit registers.
Also remove the definition of SMIAPP_DATA_TRANSFER_IF_1_CTRL_RD_EN which
has a value of zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mipid02_probe misses a check for devm_gpiod_get_optional and may miss
the failure.
Add a check to fix the problem.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add driver for Sony IMX290 CMOS image sensor driver. The driver only
supports I2C interface for programming and MIPI CSI-2 for sensor output.
[Sakari Ailus: Rewrapped a few lines over 80 chars a little.]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If VIDEO_OV5695 is y and V4L2_FWNODE is m, building fails:
drivers/media/i2c/ov5695.o: In function `ov5695_probe':
ov5695.c:(.text+0xf4c): undefined reference to `v4l2_async_register_subdev_sensor_common'
Select V4L2_FWNODE like OV5675 does.
Fixes: 623df5d710 ("media: i2c: ov5695: Modify the function of async register subdev related devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to the datasheet, both AD5821 and AD5820 share a compatible
register-set:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5821.pdf
Some camera modules also refer that AD5823 is a replacement of AD5820:
https://download.kamami.com/p564094-OV8865_DS.pdf
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since kernel 4.16, i2c devices with DT compatible tag are modprobed
using their DT modalias.
Without this patch, if this driver is build as module it would never
be autoprobed.
There is no need to mask it with CONFIG_OF to allow ACPI loading, this
also builds find with CONFIG_OF=n.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for a programmable enable pin. It can be used in
situations where the ANA-vcc is not configurable (dummy-regulator), or
just to have a more fine control of the power saving.
The use of the enable pin is optional.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Without this patch, media_device_register_entity throws a warning:
dev_warn(mdev->dev,
"Entity type for entity %s was not initialized!\n",
entity->name);
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor data sheet clearly state that 2592x1944 only works at 15 fps
make sure we don't try to miss configure the pll out of acceptable
range.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the 1920x1080 register array an extra pair of reset ctrl disable
re-enable was causing unwanted init delays.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add v4l2 controls to report the pixel rates of each mode. This is
needed by some CSI2 receiver in order to perform proper DPHY
configuration.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable rval is being initialized with a value that
is never read and is being re-assigned a little later on. The
assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A hardcoded 12 MHz master clock frequency has been assumed since
conversion of the driver from soc_camera sensor to a standalone V4L2
subdevice by commit 23a52386fa ("media: ov6650: convert to standalone
v4l2 subdevice"). Fix it.
Define a static table of supported master clock rates (fix misnamed
symbol while being at it), then use v4l2_clk_get/set_rate() to obtain
a clock rate matching one of those supported. On success, apply
respective master clock hardware divisor provided by the matching
element of the table.
[Sakari Ailus: Initialize xclk to NULL.]
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This field of the driver private structure is no longer used, drop it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As calculation of pixel clock hardware divisor no longer depends on
mbus format specific maximum pixel clock, there is no need to reapply
the divisor on format change. Drop related code from ov6650_s_fmt()
helper.
Since a master clock hardware divisor, so far applied only together
with the pixel clock divisor in a single operation, will no longer be
applied from ov6650_s_fmt(), apply it, still using a hardcoded value
for now, from ov6650_prog_dflt() helper so hardware is still
initialised correctly on device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As appears from an analysis of to_clkrc() helper code after its
pclk_limit argument has been dropped, its result no longer depends on
another argument - pclk_max. Moreover, assuming that a constant value
of FRAME_RATE_MAX is always used as a denominator of the only
significant argument left - a struct v4l2_fract, the result in fact
depends only on the numerator value of that argument. As a further
consequence, it no longer makes sense to recalculate frame intervals by
converting them forth and back with a GET_CLKRC_DIV(to_clkrc(tpf))
construct.
Drop use of GET_CLKRC_DIV() on results of to_clkrc() where possible -
use the frame interval value directly. Furthermore, replace the
to_clkrc() helper function with a simple macro and update its users to
always use FRAME_RATE_MAX as frame interval denominator and pass only
its numerator as an argument.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
That attribute used to be obtained from platform data by a soc_camera
host interface and passed to the sensor driver for .s_mbus_fmt() video
operation callback, later reused as .set_fmt() pad operation callback,
to be able to limit frame rate. The driver stored that value in its
private structure for further use from .g/s_parm(), later converted to
g/s_frame_interval().
On conversion of the driver from soc_camera sensor to a standalone V4L2
subdevice by commit 23a52386fa ("media: ov6650: convert to standalone
v4l2 subdevice"), that attribute had been replaced by a constant and
hardcoded to an arbitrarily chosen pixel clock limit. Drop it. Host
interfaces can limit frame rate if needed by calling
.s_frame_interval().
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver stores a frame interval value supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, the respective field of the structure has never been
initialised on device probe. Moreover, if updated from
.s_frame_interval(), a new value is stored before it is applied on
hardware. If an error occurs during device update, the stored value
may no longer reflect hardware state and consecutive calls to
.g_frame_interval() may return incorrect information.
Assuming a failed update of the device means its actual state hasn't
changed, update the frame interval field of the device private
structure with a new value only after it is successfully applied on
hardware so it always reflects actual hardware state to the extent
possible. Also, initialise the field with hardware default frame
interval on device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the Kconfig dependency to CONFIG_PREEMPTION.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array 'cri' on the stack but instead make it
static and const. Makes the object code smaller by 165 bytes.
Turn the 2nd parameter of 'log_infoframe()' const accordingly.
Before:
text data bss dec hex filename
98533 20024 256 118813 1d01d drivers/media/i2c/adv7842.o
After:
text data bss dec hex filename
98304 20088 256 118648 1cf78 drivers/media/i2c/adv7842.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable ret is being initialized with a value that
is never read and is being re-assigned a little later on. The
assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There appears to be a copy-paste error on the access of
csc_coeffs.y2r.r601.full.coeff, I believe csc_coeffs.2yr.r601.full.coeff
should be used instead. This is a moot point as the code is never
reached, but at least use the correct structure element.
Addresses-Coverity: ("Copy-paste error")
Fixes: 3ff3a712a9 ("media: ti-vpe: vpe: don't rely on colorspace member for conversion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the "chip found" message is shown even in the case where the
I2C address is wrongly passed in the device tree, or also in the case of
probe failure, which is misleading.
To avoid such problem, move this message after real I2C transactions
have been successfully made and we are certain that the adv7180 is
really present and probed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In af9005_identify_state when returning -EIO the allocated buffer should
be released. Replace the "return -EIO" with assignment into ret and move
deb_info() under a check.
Fixes: af4e067e1d ("V4L/DVB (5625): Add support for the AF9005 demodulator from Afatech")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drivers that use the CEC pin framework have no way of processing messages
themselves by providing the 'received' callback. This is present in
cec_ops, but not in cec_pin_ops.
Add support for this callback.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sometimes it detects a weird resolution such as 1024x287 when the
actual resolution is 1024x768. To resolve such an issue, this
commit adds clearing for hsync and vsync polarity register bits
at the beginning of the first mode detection. This is recommended
in the datasheet.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prevent inaccurate detections of resolution, this commit enables
clearing of hsync/vsync polarity bits based on probed sync state.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This introduces the required definitions for HEVC decoding support with
stateless VPUs. The controls associated to the HEVC slice format provide
the required meta-data for decoding slices extracted from the bitstream.
They are not exported to the public V4L2 API since reworking this API
will likely be needed for covering various use-cases and new hardware.
Multi-slice decoding is exposed as a valid decoding mode to match current
H.264 support but it is not yet implemented.
The interface comes with the following limitations:
* No custom quantization matrices (scaling lists);
* Support for a single temporal layer only;
* No slice entry point offsets support;
* No conformance window support;
* No VUI parameters support;
* No support for SPS extensions: range, multilayer, 3d, scc, 4 bits;
* No support for PPS extensions: range, multilayer, 3d, scc, 4 bits.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[hverkuil-cisco@xs4all.nl: use 1ULL in flags defines in hevc-ctrls.h]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support metadata output in vivid driver.
Metadata output is used to set brightness, contrast, saturation
and hue.
Adds new files for metadata output.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add new metadata format to support metadata output in vivid.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds meatadata capture support in vivid driver.
Adds new files for metadata capture.
Adds vivid controls to generate PTS and SCR for metadata stream.
also fixes v4l2-compliance issues seen on metadata device.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Touch devices have obviously no tuner, so don't attempt to enable those
ioctls for such devices.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Touch devices mark too many ioctls as valid. Restrict the list of
valid ioctls for touch devices.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In determine_valid_ioctls() we can use SET_VALID_IOCTL to enable
ioctls for SDR, simplifying the code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the type is VFL_TYPE_GRABBER, then also check device_caps
to see if the video device supports video and/or metadata and
disable unneeded ioctls.
Without this change, format ioctls for both video and metadata devices
could be called on both device nodes. This is true for other ioctls as
well, even if the device supports only video or metadata.
Metadata devices act similar to VBI devices w.r.t. which ioctls should
be enabled. This makes sense since VBI *is* metadata.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Co-developed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl2su/AeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvm4H/1jkheCrvB/GJS69
wd18vizAg+eFmNCzxlGVhpQTKGymNRy+g6clnoli3cNJ3pSVKcYgVyB3oXaONIhp
g/ANudnBjTdjqYgJzfLij5AGecrGwDpF3YL0kuKrCB63s2I/HwQGYy/aPrYY8emy
gAYdaf1DGRu5/DIIB6soTo/TnpKoAyTE+XY5MaPSug++t/Flov19tlU40IZxXW94
bjTXbm0yklrsIx+LL5mYYGGnygSTCF66JjFg1qhDCBQaS2MZ21h1ZgaOtGZTwZcc
WgEiqLC5S1Iyj96zir1t78RcVQ4RzgvDbhUOgIqUFsYAO2wOicvxyFE3Hj8rPOKd
uGgVPRM=
=xgZa
-----END PGP SIGNATURE-----
Merge v5.4-rc4 into drm-next
Thierry needs fd70c7755b ("drm/bridge: tc358767: fix max_tu_symbol
value") to be able to merge his dp_link patch series.
Some adjacent changes conflicts, plus some clashes in i915 due to
cherry-picking and git trying to be helpful and leaving both versions
in.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drivers that support VB2_V4L2_FL_SUPPORTS_M2M_HOLD_CAPTURE_BUF
typically want to know if a new frame is started (i.e. the first
slice is about to be processed). Add a new_frame bool to v4l2_m2m_ctx
and set it accordingly.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These helpers are used by stateless codecs when they support multiple
slices per frame and hold capture buffer flag is set. It's expected that
all such codecs will use this code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Co-developed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check for held buffers that are ready to be returned to vb2 in
__v4l2_m2m_try_queue(). This avoids drivers having to handle this
case.
Add v4l2_m2m_buf_done_and_job_finish() to correctly return source
and destination buffers and mark the job as finished while taking
a held destination buffer into account (i.e. that buffer won't be
returned). This has to be done while job_spinlock is held to avoid
race conditions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for the V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF
flag.
It also adds a new V4L2_BUF_CAP_SUPPORTS_M2M_HOLD_CAPTURE_BUF
capability.
Drivers should set vb2_queue->subsystem_flags to
VB2_V4L2_FL_SUPPORTS_M2M_HOLD_CAPTURE_BUF to indicate support
for this flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is likely that it should be UVC_METADATA_BUF_SIZE instead.
Fix it and use it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When parsing the UVC control descriptors fails, the error path tries to
cleanup a media device that hasn't been initialised, potentially
resulting in a crash. Fix this by initialising the media device before
the error handling path can be reached.
Fixes: 5a254d751e ("[media] uvcvideo: Register a v4l2_device")
Reported-by: syzbot+c86454eb3af9e8a4da20@syzkaller.appspotmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I2C ops are expensive, as the I2C bus typical speed is 100kbps.
Also, stats reading take some time, as it requires to retrieve a
certain number of packets to complete.
While we don't know the minimal for CXD2841er, trying to do it
too quickly is still a very bad idea.
So, add some sanity logic there, preventing to retrieve stats
faster than one second.
This shouldn't cause any issues with well behavior apps, as they
usually take stats on a polling rate slower than 1 second.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
While 99% of the implementation of the bitrate estimation
routine for ISDB-T is generic, the current approach mangles it
with some mb86a20s-specific thing.
Split the calculus from the specific stuff, in order to make
easier to use the same approach on other drivers requiring
a similar formula.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Add a keymap for the Tronsmart Vega S95 and S96 Android (Amlogic S905/S912)
STB devices. Both use the same IR remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: Zhong Jiang <zhongjiang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code for pulse and space is the same so remove duplication.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds USB ID for the eyeTV Geniatech T2 lite to the dvbsky driver.
This is a Geniatech T230C based stick without IR and a different USB ID.
Signed-off-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Up to now VPE was relying on the colorspace value of struct v4l2_format
as an indication to perform color space conversion from YUV to RGB or
not.
Instead we should used the source/destination fourcc codes as a more
reliable indication to perform color space conversion or not.
To do so, we rework the csc module to use "struct v4l2_format *" as
parameters, and reorganize the coefficients tables in a more logical
way.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is often useful to figure out if a pixel_format is either YUV or RGB
especially for driver who can perform the pixel encoding conversion.
Instead of having each driver implement its own "is_this_yuv/rgb"
function based on a restricted set of pixel value, it is better to do
this in centralized manner.
We therefore add a pixel_enc member to the v4l2_format_info structure to
quickly identify the related pixel encoding.
And add helper functions to check pixel encoding.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The RGB to YUV HD full range coefficients did not match the TRM values
and appeared to be a cut-n-paste from the YUV to RGB section.
Replace the entries with the values from the TRM.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All 4 of the "colorspace" components were not originally handled.
Causing issue related to xfer_func not being initialized properly.
This was found with v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For each queue we need to maintain resolutions, pixel format,
bytesperline, sizeimage, colorspace, etc.
Instead of manually adding more entries in the vpe_q_data struct, it is
better to just add a "struct v4l2_format" member and use that to store
all needed information.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil@xs4all.nl: fix checkpatch warning]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE uses VPDMA (built-in dma engine) to transfer data to and from the IP
and memory. VPDMA expect 32 bits addresses. To make sure that is always
the case set the DMA mask and coherent mask for the device.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using dma_addr_t as the type to hold address inside of a fix sized
descriptor used by the vpdma firmware is prone to fail when the expected
width is 32 bits and suddenly when CONFIG_LPAE is enabled the data size
is now 64 bits shifted the remaining members of the descriptor in memory
which confuses the firmware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(691): ret == 0
fail: v4l2-test-buffers.cpp(974): captureBufs(node, q, m2m_q,
frame_count, true)
test MMAP: FAIL
This caused the following Kernel Warning:
WARNING: CPU: 0 PID: 961 at
drivers/media/v4l2-core/videobuf2-core.c:1658
__vb2_queue_cancel+0x174/0x1d8
...
CPU: 0 PID: 961 Comm: v4l2-compliance Not tainted
4.14.62-01720-g20ecd717e87a #6
Hardware name: Generic DRA72X (Flattened Device Tree)
Backtrace:
[<c020b5bc>] (dump_backtrace) from [<c020b8a0>] (show_stack+0x18/0x1c)
r7:00000009 r6:60070013 r5:00000000 r4:c1053824
[<c020b888>] (show_stack) from [<c09232e8>] (dump_stack+0x90/0xa4)
[<c0923258>] (dump_stack) from [<c022b740>] (__warn+0xec/0x104)
r7:00000009 r6:c0c0ad50 r5:00000000 r4:00000000
[<c022b654>] (__warn) from [<c022b810>] (warn_slowpath_null+0x28/0x30)
r9:00000008 r8:00000000 r7:eced4808 r6:edbc9bac r5:eced4844
r4:eced4808
[<c022b7e8>] (warn_slowpath_null) from [<c0726f48>]
(__vb2_queue_cancel+0x174/0x1d8)
[<c0726dd4>] (__vb2_queue_cancel) from [<c0727648>]
(vb2_core_queue_release+0x20/0x40)
r10:ecc7bd70 r9:00000008 r8:00000000 r7:edb73010 r6:edbc9bac
r5:eced4844
r4:eced4808 r3:00000004
[<c0727628>] (vb2_core_queue_release) from [<c0729528>]
(vb2_queue_release+0x10/0x14)
r5:edbc9810 r4:eced4800
[<c0729518>] (vb2_queue_release) from [<c0724d08>]
(v4l2_m2m_ctx_release+0x1c/0x30)
[<c0724cec>] (v4l2_m2m_ctx_release) from [<bf0e8f28>]
(vpe_release+0x74/0xb0 [ti_vpe])
r5:edbc9810 r4:ed67a400
[<bf0e8eb4>] (vpe_release [ti_vpe]) from [<c070fccc>]
(v4l2_release+0x3c/0x80)
r7:edb73010 r6:ed176aa0 r5:edbc9868 r4:ed5119c0
[<c070fc90>] (v4l2_release) from [<c033cf1c>] (__fput+0x8c/0x1dc)
r5:ecc7bd70 r4:ed5119c0
[<c033ce90>] (__fput) from [<c033d0cc>] (____fput+0x10/0x14)
r10:00000000 r9:ed5119c0 r8:ece392d0 r7:c1059544 r6:ece38d80
r5:ece392b4
r4:00000000
[<c033d0bc>] (____fput) from [<c0246e00>] (task_work_run+0x98/0xb8)
[<c0246d68>] (task_work_run) from [<c022f1d8>] (do_exit+0x170/0xa80)
r9:ece351fc r8:00000000 r7:ecde3f58 r6:ffffe000 r5:ece351c0
r4:ece38d80
[<c022f068>] (do_exit) from [<c022fb6c>] (do_group_exit+0x48/0xc4)
r7:000000f8
[<c022fb24>] (do_group_exit) from [<c022fc00>]
(__wake_up_parent+0x0/0x28)
r7:000000f8 r6:b6c6a798 r5:00000001 r4:00000001
[<c022fbe8>] (SyS_exit_group) from [<c0207c80>]
(ret_fast_syscall+0x0/0x4c)
These warnings are caused by buffers which not properly cleaned
up/release during an abort use case.
In the abort cases the VPDMA desc buffers would still be mapped and the
in-flight VB2 buffers would not be released properly causing a kernel
warning from being generated by the videobuf2-core level.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(463): !pfmt.sizeimage
fail: v4l2-test-formats.cpp(736): \
Video Capture Multiplanar is valid, \
but TRY_FMT failed to return a format
test VIDIOC_TRY_FMT: FAIL
This failure is causd by the driver failing to handle out range
'bytesperline' values from user space applications.
VPDMA hardware is limited to 64k line stride (16 bytes aligned, so 65520
bytes). So make sure the provided or calculated 'bytesperline' is
smaller than the maximum value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
test VIDIOC_TRY_FMT: FAIL
This causes the following kernel panic:
Unable to handle kernel paging request at virtual address 56595561
pgd = ecd80e00
*pgd=00000000
Internal error: Oops: 205 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 930 Comm: v4l2-compliance Not tainted \
4.14.62-01715-gc8cd67f49a19 #1
Hardware name: Generic DRA72X (Flattened Device Tree)
task: ece44d80 task.stack: ecc6e000
PC is at __vpe_try_fmt+0x18c/0x2a8 [ti_vpe]
LR is at 0x8
Because the driver fails to properly check the 'num_planes' values for
proper ranges it ends up accessing out of bound data causing the kernel
panic.
Since this driver only handle single or dual plane pixel format, make
sure the provided value does not exceed 2 planes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE's max height supported MAX_H is set to 1184 which is the
padded height from VC1 decoder output.
In case of 90, 270 degree rotated video processing, input to
VPE will be 1080x1920, 720x1280 etc and MAX_H needs to be set
correct value. Setting MAX_H to 2048 as worst case height.
Signed-off-by: Ram Prasad <x0038811@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In NV21 format, the chroma plane is written to memory such that the U
and V components are swapped for NV12.
Create a new entry in the VPDMA formats to describe the correct data
types used in the data descriptors.
Update all checks for NV12 and add NV21 there as well.
Add support for V4L2_PIX_FMT_NV21 format for both capture and output
streams.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
SEQ_BT indicates the buffer for bottom field needs to be processed
before the top field.
Simplify the field selection logic to support SEQ_BT as well.
Modify the interlace flags to include any of alternate, SEQ_TB, SEQ_BT.
Update other format error checking to consider SEQ_BT.
Replace SEQ_TB with SEQ_XX wherever applicable.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of saving a pointer to the 'fh' member of struct vpe_ctx to
later have to use container_of to retrieve the actual pointer to the
context structure, which seems to confuse static code analysis tool
anyways, just save the pointer to the actual structure and then retrieve
it directly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user
specified stride") and commit da4414eaed ("[media] media: ti-vpe: vpdma:
add support for user specified stride") resulted in the Motion Vector
stride to be the same as the image stride.
This caused memory corruption in the output image as mentioned in
commit 00db969964 ("[media] media: ti-vpe: vpe: Fix line stride
for output motion vector").
Fixes: 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user specified stride")
Fixes: da4414eaed ("[media] media: ti-vpe: vpdma: add support for user specified stride")
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When TI CAL was introduce as another driver under platform/ti-vpe
adding a second entry into the ti-vpe directory in the platform
Makefile caused issues during parallel build.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This control returns the unit cell size in nanometres. The struct provides
the width and the height in separated fields to take into consideration
asymmetric pixels and/or hardware binning.
This control is required for automatic calibration of sensors/cameras.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This type contains the width and the height of a rectangular area.
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently compound controls do not have a simple way of initializing its
values. This results in ofuscated code with type_ops init.
This patch introduces a new field on the control with the default value
for the compound control that can be set with the brand new
v4l2_ctrl_new_std_compound function
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
[hverkuil@xs4all.nl: fix checkpatch warning]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simplify these function implementations by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The image size is doubled for NV16 and is calculated as bytesperline *
height * 2 to accommodate the split of UV data. When writing the offset
to hardware, the width is used instead of bytesperline, fix this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The rectangle used to correct the compose settings when changing the
format was created inside a helper function and not where it was used.
This is confusing and makes the code harder to read, fix this.
This cleanup is made possible due to refactoring elsewhere and there is
no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After recent refactoring the rectangle named crop no longer reflects it
usage, to contain the source rectangle. Fix this by renaming it. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f13d5f3619 ("media: vimc: Collapse component structure into a single monolithic driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Visual inspection of the usbvision driver shows that it suffers from
three races between its open, close, and disconnect handlers. In
particular, the driver is careful to update its usbvision->user and
usbvision->remove_pending flags while holding the private mutex, but:
usbvision_v4l2_close() and usbvision_radio_close() don't hold
the mutex while they check the value of
usbvision->remove_pending;
usbvision_disconnect() doesn't hold the mutex while checking
the value of usbvision->user; and
also, usbvision_v4l2_open() and usbvision_radio_open() don't
check whether the device has been unplugged before allowing
the user to open the device files.
Each of these can potentially lead to usbvision_release() being called
twice and use-after-free errors.
This patch fixes the races by reading the flags while the mutex is
still held and checking for pending removes before allowing an open to
succeed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The syzbot fuzzer found two invalid-access bugs in the usbvision
driver. These bugs occur when userspace keeps the device file open
after the device has been disconnected and usbvision_disconnect() has
set usbvision->dev to NULL:
When the device file is closed, usbvision_radio_close() tries
to issue a usb_set_interface() call, passing the NULL pointer
as its first argument.
If userspace performs a querycap ioctl call, vidioc_querycap()
calls usb_make_path() with the same NULL pointer.
This patch fixes the problems by making the appropriate tests
beforehand. Note that vidioc_querycap() is protected by
usbvision->v4l2_lock, acquired in a higher layer of the V4L2
subsystem.
Reported-and-tested-by: syzbot+7fa38a608b1075dfd634@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array st6422_bridge_init on the stack but instead
make it static. Makes the object code smaller by 231 bytes.
Before:
text data bss dec hex filename
3419 752 64 4235 108b gspca/stv06xx/stv06xx_st6422.o
After:
text data bss dec hex filename
3124 816 64 4004 fa4 gspca/stv06xx/stv06xx_st6422.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array mapping on the stack but instead make it
static. Makes the object code smaller by 79 bytes.
Before:
text data bss dec hex filename
27572 2096 0 29668 73e4 drivers/media/pci/cx18/cx18-ioctl.o
After:
text data bss dec hex filename
27429 2160 0 29589 7395 drivers/media/pci/cx18/cx18-ioctl.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A call to 'pci_disable_device()' is missing in the error handling path.
In some cases, a call to 'free_irq()' may also be missing.
Reorder the error handling path, add some new labels and fix the 2 issues
mentionned above.
This way, the error handling path in more in line with 'cx8800_finidev()'
(i.e. the remove function)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The 2nd parameter of 'find_first_zero_bit()' is a number of bits, not of
bytes. So use 'csi2rx->max_lanes' instead of 'sizeof(lanes_used)'.
Fixes: 1fc3b37f34 ("media: v4l: cadence: Add Cadence MIPI-CSI2 RX driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In sd_start the return value of create_singlethread_workqueue needs
null check.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
div_u64() does a 64-by-32 division, while the divisor max2175.xtal_freq
is unsigned long, thus 64-bit on 64-bit platforms. Hence the proper
function to call is div64_ul().
Note that this change does not have any functional impact, as the
crystal frequency must be much lower than the 32-bit limit anyway.
On 32-bit platforms, the generated code is the same. But at least on
arm64, this saves an AND-instruction to truncate xtal_freq to 32-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Inside function compress_sliced_buf(), variable vbi.type is
uninitialized if macro v4l2_subdev_call set __result an
error code. However, vbi.type is used in the if statement
without any check, which is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This includes a hack for the device as it returns only 0xff after a new
firmware is loaded. To quote Mauro:
"When the [...] firmware that came with the device is replaced
by a new one, any I2C data received from the tuner will be
replaced by 0xff.
Probably, the vendor firmware has some patch specifically
designed for this device. So, we can't replace by the generic
firmware.
The right solution would be to extract the [...] firmware from
the original driver and ask the driver to load the specifically
designed firmware, but, while we don't have that, the next best
solution is to just keep the original firmware at the device."
Signed-off-by: Gon Solo <gonsolo@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While at it, convert to kernel-doc format and use bits instead of bools.
Signed-off-by: Gon Solo <gonsolo@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A very old patch sent to the media ML used to contain the
I2C speed formula:
https://lore.kernel.org/linux-media/1312539895.2763.33.camel@Jason-Linux/
When the ite9135 code was merged with af9035, the formula was
lost. As we might need to slow down the speed for some devices,
add the formula again.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using bool on struct is not recommended, as it wastes lots of
space. So, instead, let's use bits.
While here, convert the comments to kernel-doc format.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As reported by jenkins@linuxtv.org, the build with i386 fails
with:
ld: drivers/media/platform/qcom/venus/helpers.o: in function `venus_helper_load_scale_clocks':
(.text+0x1d77): undefined reference to `__udivdi3'
ld: (.text+0x1dce): undefined reference to `__udivdi3'
make: *** [Makefile:1094: vmlinux] Error 1
That's because it divides an u32 bit integer by a u64 one.
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If usb_set_interface() failed, iface->cur_altsetting will
not be assigned and it will be used in flexcop_usb_transfer_init()
It may lead a NULL pointer dereference.
Check usb_set_interface() return value in flexcop_usb_init()
and return failed to avoid using this NULL pointer.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support Friio devices to read from tuner via demod tc90522,
by enabling the config option.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This demod implements an i2c adapter for attached tuner
and relays i2c messages from users (dvb adapters / bridge chips).
Some of them, such as Friio dvb card using gl861,
require each pair of i2c messages for one read to be issued as
two separate transactions.
This patch adds a configuration option to enable this split.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The header contained just internal definitions
and they are not used anymore.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For Friio dvb cards, a distinct I2C algo was provided to support
some "long" I2C messages used in relaying tuner I2C via demod.
Since the other (generic) i2c algo in this module has been patched
to support those messages in a more generic way,
this patch replaces and integrates the device-specific i2c algo
with the generic one and simplifies the code.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Device I2C adapter is capable of writing and reading large messages.
For I2C writes there is 2 methods: simple for max 2 byte messages and
usb_control_msg() with payload data for larger I2C messages. Add I2C
adapter logic which selects suitable method according to message size.
Add also support for plain I2C read.
Cc: Akihiro TSUKADA <tskd08@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is possible for one HDMI connector to have multiple CEC adapters. The
typical real-world scenario is that where one adapter is used when the
device is in standby, and one that's better/smarter when the device is
powered up.
The cec-notifier changes were made with that in mind, but I missed that in
order to support this you need to tell cec_notifier_cec_adap_unregister()
which adapter you are unregistering from the notifier.
Add this additional argument. It is currently unused, but once all drivers
use this, the CEC core will be adapted for these use-cases.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e9fc8740-6be6-43a7-beee-ce2d7b54936e@xs4all.nl
Re-use usb_mutex from dvb_usb_device for this.
Tested-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Andrei Koshkosh <andreykosh000@mail.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable rc is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch corrects the SPDX License Identifier style
in header files for TV Master Media USB Adapter drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch corrects the SPDX License Identifier style
in header file related to Remote Controller Driver for Linux.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In cx23888_ir_probe if kfifo_alloc fails the allocated memory for state
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for Magix Wideowandler 2 - analog USB capture card
Signed-off-by: Dominik Danelski <dominik@danelski.pl>
Co-author: Cornelius Porosanu <cornelius591@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array tab on the stack but instead make it
static const. Makes the object size smaller by 170 bytes in total.
Before:
text data bss dec hex filename
7045 1736 0 8781 224d media/dvb-frontends/cxd2820r_c.o
8800 2216 0 11016 2b08 media/dvb-frontends/cxd2820r_t.o
8981 2120 0 11101 2b5d media/dvb-frontends/cxd2820r_t2.o
After:
text data bss dec hex filename
6896 1832 0 8728 2218 media/dvb-frontends/cxd2820r_c.o
8651 2312 0 10963 2ad3 media/dvb-frontends/cxd2820r_t.o
8853 2184 0 11037 2b1d media/dvb-frontends/cxd2820r_t2.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the IR receiver is put into idle mode after each interrupt.
However longer IR like NEC can be distributed over multiple interrupts,
so putting the IR into idle in the middle of such a message will break
decoding.
Every IR message has a trailing space of 0xbf (one less than
IR_IDE_LEN{0,1} which is programmed to 0xc0). So, set the timeout to that
value and rc-core will put the IR receiver into idle mode automatically.
Thanks to Jan Pieter van Woerkom <jp@jpvw.nl> for providing the hardware.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Thanks to Jan Pieter van Woerkom <jp@jpvw.nl> for providing the hardware.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The device it's an iMON UltraBay (0x98 in config byte) with LCD,
IR and dual-knobs front panel.
To work properly the device also require its own key table,
and repeat suppression for all buttons.
Signed-off-by: Flavius Georgescu <pretoriano.mp@gmail.com>
Co-developed-by: Chris Vandomelen <chris@sightworks.com>
Signed-off-by: Chris Vandomelen <chris@sightworks.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix multiple cases of out of bounds (OOB) read associated with
MCE device receive/input data handling.
In reference for the OOB cases below, the incoming/read (byte) data
format when the MCE device responds to a command is:
{ cmd_prefix, subcmd, data0, data1, ... }
where cmd_prefix are:
MCE_CMD_PORT_SYS
MCE_CMD_PORT_IR
and subcmd examples are:
MCE_RSP_GETPORTSTATUS
MCE_RSP_EQIRNUMPORTS
...
Response size dynamically depends on cmd_prefix and subcmd.
So data0, data1, ... may or may not be present on input.
Multiple responses may return in a single receiver buffer.
The trigger condition for OOB read is typically random or
corrupt input data that fills the mceusb receiver buffer.
Case 1:
mceusb_handle_command() reads data0 (var hi) and data1 (var lo)
regardless of whether the response includes such data.
If { cmd_prefix, subcmd } is at the end of the receiver buffer,
read past end of buffer occurs.
This case was reported by
KASAN: slab-out-of-bounds Read in mceusb_dev_recv
https://syzkaller.appspot.com/bug?extid=c7fdb6cb36e65f2fe8c9
Fix: In mceusb_handle_command(), change variable hi and lo to
pointers, and dereference only when required.
Case 2:
If response with data is truncated at end of buffer after
{ cmd_prefix, subcmd }, mceusb_handle_command() reads past
end of buffer for data0, data1, ...
Fix: In mceusb_process_ir_data(), check response size with
remaining buffer size before invoking mceusb_handle_command().
+ if (i + ir->rem < buf_len)
mceusb_handle_command(ir, &ir->buf_in[i - 1]);
Case 3:
mceusb_handle_command() handles invalid/bad response such as
{ 0x??, MCE_RSP_GETPORTSTATUS } of length 2 as a response
{ MCE_CMD_PORT_SYS, MCE_RSP_GETPORTSTATUS, data0, ... }
of length 7. Read OOB occurs for non-existent data0, data1, ...
Cause is mceusb_handle_command() does not check cmd_prefix value.
Fix: mceusb_handle_command() must test both cmd_prefix and subcmd.
Case 4:
mceusb_process_ir_data() receiver parser state SUBCMD is
possible at start (i=0) of receiver buffer resulting in buffer
offset=-1 passed to mceusb_dev_printdata().
Bad offset results in OOB read before start of buffer.
[1214218.580308] mceusb 1-1.3:1.0: rx data[0]: 00 80 (length=2)
[1214218.580323] mceusb 1-1.3:1.0: Unknown command 0x00 0x80
...
[1214218.580406] mceusb 1-1.3:1.0: rx data[14]: 7f 7f (length=2)
[1214218.679311] mceusb 1-1.3:1.0: rx data[-1]: 80 90 (length=2)
[1214218.679325] mceusb 1-1.3:1.0: End of raw IR data
[1214218.679340] mceusb 1-1.3:1.0: rx data[1]: 7f 7f (length=2)
Fix: If parser_state is SUBCMD after processing receiver buffer,
reset parser_state to CMD_HEADER.
In effect, discard cmd_prefix at end of receiver buffer.
In mceusb_dev_printdata(), abort if buffer offset is out of bounds.
Case 5:
If response with data is truncated at end of buffer after
{ cmd_prefix, subcmd }, mceusb_dev_printdata() reads past
end of buffer for data0, data1, ...
while decoding the response to print out.
Fix: In mceusb_dev_printdata(), remove unneeded buffer offset
adjustments (var start and var skip) associated with MCE gen1 header.
Test for truncated MCE cmd response (compare offset+len with buf_len)
and skip decoding of incomplete response.
Move IR data tracing to execute before the truncation test.
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Decoding often fails on e.g. redrat3 devices. The dev_dbg() helps
with debugging when decoding does fail.
Cc: Patrick Lerda <patrick9876@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
libinput refuses pointer movement from rc-core, since it believes it's not
a pointer-type device:
libinput error: event17 - Media Center Ed. eHome Infrared Remote Transceiver (1784:0008): libinput bug: REL_X/Y from a non-pointer device
Fixes: 158bc148a3 ("media: rc: mce_kbd: input events via rc-core's input device")
Fixes: 0ac5a603a7 ("media: rc: imon: report mouse events using rc-core's input device")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
procfs is no longer used anywhere in media.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This moves /proc/saa7164 to /sys/kernel/debug/saa7164.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When probed after the HDMI notifier, calling cec_notifier_cec_adap_register()
calls the enable() adapter callback, but the HW is not yet set up.
Moving cec_notifier_cec_adap_register() right before cec_register_adapter()
fixes the following crash:
Ignoring spurious kernel translation fault at virtual address 0000000000000008
[...]
Hardware name: Khadas VIM (DT)
[...]
pc : __do_kernel_fault+0xdc/0x120
lr : __do_kernel_fault+0xdc/0x120
[...]
Call trace:
__do_kernel_fault+0xdc/0x120
do_page_fault+0x180/0x458
do_translation_fault+0x64/0x70
do_mem_abort+0x3c/0x98
el1_da+0x20/0x94
meson_ao_cec_adap_enable+0x30/0x218 [ao_cec]
__cec_s_phys_addr+0x184/0x270
cec_s_phys_addr+0x44/0x60
cec_notifier_cec_adap_register+0x68/0x90
meson_ao_cec_probe+0xb0/0x288 [ao_cec]
[...]
el0_svc_compat+0x8/0x10
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 20958f9d5c ("media: meson/ao-cec: use cec_notifier_cec_adap_(un)register")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Note that runtime PM has never actually been enabled for this driver
since the support_autosuspend flag in its usb_driver struct is not set.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current clock scaling calculations are same for vpu4 and
previous versions. For vpu4, Clock scaling calculations
are updated with cycles/mb and bitrate. This helps in
getting precise clock required.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add vpp cycles for different types of codec.
It indicates the cycles required by video hardware
to process each macroblock. Add vsp cycles, cycles
required by stream processor. Initialize the codec
data with core resources.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Failure to suspend (venus_suspend_3xx) happens when the system
is fresh booted and loading venus driver. This happens once and
after reload the venus driver modules the problem disrepair.
Fix the failure by skipping the check for WFI and IDLE bits if
PC_READY is on in control status register.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This aims to add a requests for bandwidth scaling depending
on the resolution and framerate (macroblocks per second). The
exact value of the requested bandwidth is get from a
pre-calculated tables for encoder and decoder.
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In downstream driver, there are two frequency tables defined,
one for the encoder and one for the decoder:
/* Encoders /
<972000 490000000 0x55555555>, / 4k UHD @ 30 /
<489600 320000000 0x55555555>, / 1080p @ 60 /
<244800 150000000 0x55555555>, / 1080p @ 30 /
<108000 75000000 0x55555555>, / 720p @ 30 */
/* Decoders /
<1944000 490000000 0xffffffff>, / 4k UHD @ 60 /
< 972000 320000000 0xffffffff>, / 4k UHD @ 30 /
< 489600 150000000 0xffffffff>, / 1080p @ 60 /
< 244800 75000000 0xffffffff>; / 1080p @ 30 */
It shows that encoder always needs a higher clock than decoder.
In current venus driver, the unified frequency table is aligned
with the downstream decoder table which causes performance issues
in encoding scenarios. Fix that by aligning frequency table on
worst case (encoding).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The initial registers sequence is only loaded at probe
time. Afterward only the resolution and format specific
register are modified. Care must be taken to make sure
registers modified by one resolution setting are reverted
back when another resolution is programmed.
This was not done properly for the 720p case.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On some board it is possible that the sensor 'powerdown' and or 'reset'
pin might be controlled by gpio instead of being tied.
To implement we add pm_runtime support which will handle the power
up/down sequence when it is available otherwise the sensor will be
powered on at module insertion/probe and powered off at module removal.
Now originally the driver assumed that the sensor would always stay
powered and keep its register setting. We cannot assume this anymore, so
every time we "power up" we need to re-program the initial registers
configuration first. This was previously done only at probe time.
[Sakari Ailus: Resolve a conflict in Kconfig]
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In ov2659_s_stream() return value for invoked function should be checked
and propagated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several of include files listed are not explicitly needed.
If they are need then they are implicitly included.
Reduce the list of includes to an easier to manage list.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that if the expected sensor device id register
is not recognized properly the failure is propagated
up so devices are not left partially initialized.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on recently found sensor configuration examples, it was
discovered that when scaling and binning are used for the lower
resolutions (i.e. 640x480, 320x240) the read offset has to be
increased otherwise the image appears to be wrapped around.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for registering a sensor sub-device to the async
sub-device framework and parse set up common sensor related devices such as
actuator/VCM.
[Sakari Ailus: Rewrap commit message]
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Assign vep->link_frequencies to NULL after releasing its memory. Without
this change, multiple calls to v4l2_fwnode_endpoint_free() would result in
double kfree calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of individually depending on MEDIA_CAMERA_SUPPORT (or forgetting
it), put all camera sensor, lens and flash drivers under
MEDIA_CAMERA_SUPPORT as a whole. The lens VCM devices didn't use to do
this, but make them depend on MEDIA_CAMERA_SUPPORT as well since there's
no use for these devices without that in practice.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver stores crop rectangle settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, crop rectangle width and height settings are not updated
correctly when rectangle offset settings are applied on hardware. If
an error occurs while the device is updated, the stored settings my no
longer reflect hardware state and consecutive calls to .get_selection()
as well as .get/set_fmt() may return incorrect information. That in
turn may affect ability of a bridge device to use correct DMA transfer
settings if such incorrect informamtion on active frame format returned
by .get/set_fmt() is used.
Assuming a failed update of the device means its actual settings haven't
changed, update crop rectangle width and height settings stored in the
device private structure correctly while the rectangle offset is
successfully applied on hardware so the stored values always reflect
actual hardware state to the extent possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver stores frame format settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, those settings are updated before they are actually applied
on hardware. If an error occurs on device update, the stored settings
my not reflect hardware state anymore and consecutive calls to
.get_fmt() may return incorrect information. That in turn may affect
ability of a bridge device to use correct DMA transfer settings if such
incorrect informmation on active frame format returned by .get_fmt() is
used.
Assuming a failed device update means its state hasn't changed, update
frame format related settings stored in the device private structure
only after they are successfully applied so the stored values always
reflect hardware state as closely as possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not clear what pixel format is actually configured in hardware on
reset. MEDIA_BUS_FMT_YUYV8_2X8, assumed on device probe since the
driver was intiially submitted, is for sure not the one.
Fix it by explicitly applying a known, driver default frame format just
after initial device reset.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit da298c6d98 ("[media] v4l2: replace video op g_mbus_fmt by pad
op get_fmt") converted a former ov6650_g_fmt() video operation callback
to an ov6650_get_fmt() pad operation callback. However, the converted
function disregards a format->which flag that pad operations should
obey and always returns active frame format settings.
That can be fixed by always responding to V4L2_SUBDEV_FORMAT_TRY with
-EINVAL, or providing the response from a pad config argument, likely
updated by a former user call to V4L2_SUBDEV_FORMAT_TRY .set_fmt().
Since implementation of the latter is trivial, go for it.
Fixes: da298c6d98 ("[media] v4l2: replace video op g_mbus_fmt by pad op get_fmt")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
User arguments passed to .get/set_fmt() pad operation callbacks may
contain unsupported values. The driver takes control over frame size
and pixel code as well as colorspace and field attributes but has never
cared for remainig format attributes, i.e., ycbcr_enc, quantization
and xfer_func, introduced by commit 11ff030c73 ("[media]
v4l2-mediabus: improve colorspace support"). Fix it.
Set up a static v4l2_mbus_framefmt structure with attributes
initialized to reasonable defaults and use it for updating content of
user provided arguments. In case of V4L2_SUBDEV_FORMAT_ACTIVE,
postpone frame size update, now performed from inside ov6650_s_fmt()
helper, util the user argument is first updated in ov6650_set_fmt() with
default frame format content. For V4L2_SUBDEV_FORMAT_TRY, don't copy
all attributes to pad config, only those handled by the driver, then
fill the response with the default frame format updated with resulting
pad config format code and frame size.
Fixes: 11ff030c73 ("[media] v4l2-mediabus: improve colorspace support")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since its initial submission, the driver selects V4L2_COLORSPACE_JPEG
for supported formats other than V4L2_MBUS_FMT_SBGGR8_1X8. According
to v4l2-compliance test program, V4L2_COLORSPACE_JPEG applies
exclusively to V4L2_PIX_FMT_JPEG. Since the sensor does not support
JPEG format, fix it to always select V4L2_COLORSPACE_SRGB.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 4f996594ce ("[media] v4l2: make vidioc_s_crop const")
introduced a writable copy of constified user requested crop rectangle
in order to be able to perform hardware alignments on it. Later
on, commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video
ops") replaced s_crop() video operation using that const argument with
set_selection() pad operation which had a corresponding argument not
constified, however the original behavior of the driver was not
restored. Since that time, any hardware alignment applied on a user
requested crop rectangle is not passed back to the user calling
.set_selection() as it should be.
Fix the issue by dropping the copy and replacing all references to it
with references to the crop rectangle embedded in the user argument.
Fixes: 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit afd9690c72 ("[media] ov6650: convert to the control
framework"), if an error occurs during initialization of a control
handler, resources possibly allocated to the handler are not freed
before device initialiaton is aborted. Fix it.
Fixes: afd9690c72 ("[media] ov6650: convert to the control framework")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 23a52386fa ("media: ov6650: convert to standalone v4l2
subdevice") converted the driver from a soc_camera sensor to a
standalone V4L subdevice driver. Unfortunately, module description was
not updated to reflect the change. Fix it.
While being at it, update email address of the module author.
Fixes: 23a52386fa ("media: ov6650: convert to standalone v4l2 subdevice")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If CONFIG_REGMAP_I2C is not set, building fails:
drivers/media/i2c/max2175.o: In function `max2175_probe':
max2175.c:(.text+0x1404): undefined reference to `__devm_regmap_init_i2c'
Select REGMAP_I2C to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch converts the cx231xx driver to the vb2 framework.
Since you can't do a partial conversion this is a big-bang patch,
i.e. large and hard to review. I never found a way around this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Co-developed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for cec-notifier to the cec-gpio driver.
This makes it possible to associate the CEC gpio pin with an HDMI
connector. This feature was always documented in the cec-gpio bindings:
Documentation/devicetree/bindings/media/cec-gpio.txt
But support for the hdmi-phandle property was never actually implemented in
this driver.
This patch adds support for this property.
It also fixes a few incorrect error returns in the probe() function, which
skipped the call to cec_delete_adapter().
Tested on a Raspberry Pi 3B with a modified vc4 driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Until now the connector info API was a kernel-internal API only.
This moves it to the public API and adds the new ioctl to retrieve
this information.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of hardcoding the UI Command key values, use the new
defines.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware is capable to passing V4L2_FIELD_ALTERNATE to user-space.
Allow users to request this field format but still default to using the
hardware interlacer if alternating is not explicitly requested.
Before this change a sensor providing data using alternate would be
always combined to an interlaced frame. After this change the user can
request to receive frames as alternate if the sensor provides it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The crop and compose rectangles are reset when s_fmt is called
resulting in potentially valid rectangles being lost when updating the
format. Fix this by mapping the rectangles inside the new format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable to hold the video source information dimensions was poorly
named 'source'. This is confusing as a lot of other members of structs
share the same name with different purposes, rename it src_rect in
preparation of refactoring code.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_FIELD_IS_INTERLACED() can be used to make the code more
readable, use it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While refactoring code the return statement became corrupted, fix it by
returning the correct return code.
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 897e371389 ("media: rcar-vin: simplify how formats are set and reset"
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, if start streaming -> stop streaming -> start streaming
sequence is executed, driver will end job prematurely, if ctx->translen
is higher than 1, because "aborting" flag is still set from previous
stop streaming command.
Fix that by clearing "aborting" flag in start streaming handler.
Fixes: 96d8eab5d0 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It should be "%u.%02u" instead of "%u.%u".
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Bard Winther <bwinther@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check for a potentially NULL pointer that was overlooked and use shorter
accessors to the same data. While we are at it, sprinkle a few comments.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each of the supported decoder formats used to set the same RPC
interrupt handler by themselves, even though this could be done
by the IF init function itself. Move it to the right place and stop
making its symbol public.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mtk_q_data::fmt is actually a pointer and must be dereferenced as such.
This went under the radar because mtk_v4l2_debug() evaluates to nothing
unless DEBUG is defined.
[acourbot: split into its own commit]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the arrays on the stack but instead make them
static const. Makes the object code smaller by 767 bytes.
Before:
text data bss dec hex filename
41567 15088 192 56847 de0f em28xx/em28xx-dvb.o
After:
text data bss dec hex filename
39872 16016 192 56080 db10 em28xx/em28xx-dvb.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array 'registers' on the stack but instead make it
static const. Makes the object code smaller by 45 bytes.
Before:
text data bss dec hex filename
17364 5000 0 22364 575c platform/s3c-camif/camif-regs.o
After:
text data bss dec hex filename
17255 5064 0 22319 572f platform/s3c-camif/camif-regs.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the beginning of the probe function, we have a call to
'request_muxed_region(BRA_SMB_BASE_ADDR, 7, "CEC00001")()'
A corresponding 'release_region()' is performed in the remove function but
is lacking in the error handling path.
Add it.
Fixes: b03c2fb97a ("media: add SECO cec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bus related static data included in the vpfe_fmt
static table can be derived dynamically instead.
This simplify the table and it's use.
We instead replace the per bus data info with just
the usual bit per pixel value for each supported
pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The try_fmt was not actually trying out the provided format
but merely returning the current format basically like get_fmt.
In addition set_fmt should first invoked try_fmt to validate the
given format before applying it to the hardware.
To fix all of these the whole get/try/set ioctl functions had to
be reworked.
When calculating the bytesperline/stride and sizeimage format
member we don't need to locally store the current value of
bytesperpixel as it can easily get derived dynamically.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
checkpatch.pl nows reports several:
WARNING: Prefer using '"%s...", __func__' to using '<function name>',
this function's name, in a string.
So fix these for the whole driver.
At the same time remove the function entry trace log as those can be
enabled using ftrace instead.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using a statically defined format array would cause issue when
multiple vpfe instance would be connected to sub-device of
different capabilities. We need to use an instance based array
instead to properly maintain a per port/instance format list.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VIDIOC_S_STD should not return an error if the value is identical
to the current one.
This error was highlighted by the v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Returning queued vb2 buffers back to user space is a common
task best handled by a helper function.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming fails the h/w module might be left enabled
inadvertently. Make sure it is disabled in the error path.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We were originally attempting to stop all processing as soon
as possible, but the in-progress DMA operation cannot be canceled.
This led to the module being in a busy state and prevented proper
power management functionality.
The existing implementation would attempt to clean things up by waiting
up to 50ms. However when receiving video frame at 15fps or lower,
it meant an inter frame arrival rate of 66.6 ms or higher.
In such cases upon tear down the following message could be seen:
omap_hwmod: vpfe0: _wait_target_disable failed
This patch fixes this issue by adding a stopping state where
we would wait for the next Vsync before disabling the hardware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Previous generation of this driver were hard coded to handle
encoder/decoder where the first line never contains any data and
was therefore always skipped, however when dealing with actual
camera sensors the first line is always present.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently if vpfe is not active then it returns immediately in the
suspend and resume handlers. Change this so that it always performs the
pinctrl config so that we can still get proper sleep state configuration
on the pins even if we do not need to worry about fully saving and
restoring context.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move duplicated IS_SRC and IS_SINK dfines to common header. Rename
them to VIMC_IS_SRC and VIM_IS_SINK.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc uses Component API to split the driver into functional components.
The real hardware resembles a monolith structure than component and
component structure added a level of complexity making it hard to
maintain without adding any real benefit.
The sensor is one vimc component that would makes sense to be a separate
module to closely align with the real hardware. It would be easier to
collapse vimc into single monolithic driver first and then split the
sensor off as a separate module.
Collapse it into a single monolithic driver removing the Component API.
This patch removes the component API and makes minimal changes to the
code base preserving the functional division of the code structure.
Preserving the functional structure allows us to split the sensor off
as a separate module in the future.
Major design elements in this change are:
- Use existing struct vimc_ent_config and struct vimc_pipeline_config
to drive the initialization of the functional components.
- Make vimc_device and vimc_ent_config global by moving them to
vimc-common.h
- Add two new hooks add and rm to initialize and register, unregister
and free subdevs.
- All component API is now gone and bind and unbind hooks are modified
to do "add" and "rm" with minimal changes to just add and rm subdevs.
- vimc-core's bind and unbind are now register and unregister.
- Add a new field to vimc_device structure for saving the pointers to
struct vimc_ent_device(s) subdevs create in their "add" hooks. These
get used to create links and removing the subdevs. vimc-core allocates
this array which sized to number of entries in the topology defined in
the vimc_pipeline_config structure.
- vimc-core invokes "add" hooks from its vimc_register_devices().
The "add" hooks remain the same and register subdevs. They don't
create platform devices of their own and use vimc's pdev.dev as
their reference device. Each "add" hook returns pointer to its struct
vimc_ent_device. This is saved in the vimc_device ent_devs array.
- vimc-core invokes "rm" hooks from its unregister to unregister subdevs
and cleanup.
- vimc-core invokes "add" and "rm" hooks with pointer to struct vimc_device
and the corresponding vimc_ent_device saved in the ent_devs.
The following configure and stream test works on all devices.
media-ctl -d platform:vimc -V '"Sensor A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Sensor B":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer B":0[fmt:SBGGR8_1X8/640x480]'
v4l2-ctl -z platform:vimc -d "RGB/YUV Capture" -v width=1920,height=1440
v4l2-ctl -z platform:vimc -d "Raw Capture 0" -v pixelformat=BA81
v4l2-ctl -z platform:vimc -d "Raw Capture 1" -v pixelformat=BA81
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video1
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video2
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video3
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In media_device_register_entity, if media_graph_walk_init fails,
need to free the previously memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array init_regs on the stack but instead make it
static. Makes the object code smaller by 57 bytes.
Before:
text data bss dec hex filename
15935 3600 128 19663 4ccf drivers/media/i2c/mt9m001.o
After:
text data bss dec hex filename
15782 3696 128 19606 4c96 drivers/media/i2c/mt9m001.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch is a part of a series that extends kernel ABI to allow to pass
tagged user pointers (with the top byte set to something else other than
0x00) as syscall arguments.
videobuf_dma_contig_user_get() uses provided user pointers for vma
lookups, which can only by done with untagged pointers.
Untag the pointers in this function.
Link: http://lkml.kernel.org/r/100436d5f8e4349a78f27b0bbb27e4801fcb946b.1563904656.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl1/essACgkQCF8+vY7k
4RV4YQ/+IILxwEuXn6cU2H/ss2+6QmOdOYISGDniWRQGTE9NN4AuvF7jv3qxek5o
FqisJXFJWCzpO7+LpKomAQXweWmVGaSV99QSJhRUyM0lNIrXD+rACO77yYL5ZwSX
r5REvk+ykozgRrQrWpiHCGOyH08Kt/LO/jA29VaJokX6yX4w0xvRc0rUBe2OlL+K
rcaXDnVw8SloVpyDaMY0DDqP8v0iGsUufTxFwAoskL36+qudXgunrg1yoNwmvTL+
spxLFs/I2LBIuBdvSg5W+FmwC3YnMdE/BDiaor9jKvhqUT9hOIozZ+pNmVTEsfvk
1FdTobf2mhvzmJrn4bdQSfFb7BiDNgMuf6/IpeRJqQSpQHzyHQhVGBG8h3axSOhM
5QWHBqrA0MAhcwVsKBUKj+mcfg7uNxtGPqmoeSVlMz+LH1hhokNWTAq5p2FgiDh8
wrSsZyJItHg2hbXPkWP9EgA40Q/xzwsvUCvoz0/+dCd08DwIeSi2HIQbNddxg7y8
NllZY0o4h6ETeDIfQb6k3zrRnAqOwlxxvXIMlaGanYegZBXMltiBIqiWrUG1qQh5
CrBTAE28vBCNNTxQJyEjut6H5/RpWEFwebcUkn1BkeUAPZ1w72+LTJ/obekiC0/6
Dxv7VvoTG+UFO14Fz7L3lYYTK2+OGvAsuXHAhQgrW5bWfmm8Cog=
=QTT+
-----END PGP SIGNATURE-----
Merge tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new sensor driver for ov5675
- a new platform driver for Allwinner A10 sensor interface
- some new remote controller keymaps
- some cosmetic changes at V4L2 core in order to avoid #ifdefs and to
merge two core modules into one
- removal of bcm2048 radio driver from staging
- removal of davinci_vpfe video driver from staging
- regression fix since Kernel 5.1 at the legacy VideoBuffer version 1
core
- added some documentation for remote controller protocols
- pixel format documentation was split on two files
- lots of other driver improvements and cleanups
* tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (321 commits)
media: videobuf-core.c: poll_wait needs a non-NULL buf pointer
media: sun4i: Make sun4i_csi_formats static
media: imx: remove unused including <linux/version.h>
media: stm32-dcmi: Delete an unnecessary of_node_put() call in dcmi_probe()
media: pvrusb2: qctrl.flag will be uninitlaized if cx2341x_ctrl_query() returns error code
media: em28xx: Fix exception handling in em28xx_alloc_urbs()
media: don't do a 31 bit shift on a signed int
media: use the BIT() macro
media: ov9650: add a sanity check
media: aspeed-video: address a protential usage of an unitialized var
media: vicodec: make life easier for static analyzers
media: remove include stdarg.h from some drivers
v4l2-core: fix coding style for the two new c files
media: v4l2-core: Remove BUG() from i2c and spi helpers
media: v4l2-core: introduce a helper to unregister a i2c subdev
media: v4l2-core: introduce a helper to unregister a spi subdev
media: v4l2-core: move i2c helpers out of v4l2-common.c
media: v4l2-core: move spi helpers out of v4l2-common.c
media: v4l2-core: Module re-organization
media: usbvision: Remove dead code
...
poll_wait uses &buf->done, but buf is NULL. Move the poll_wait to later
in the function once buf is correctly set and only call it if it is
non-NULL.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: bb436cbeb9 ("media: videobuf: fix epoll() by calling poll_wait first")
Cc: <stable@vger.kernel.org> # for v5.1 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The sun4i_csi_formats array is only used in sun4i_v4l2.c, so it doesn't
make any sense to have it !static.
[Sakari Ailus: const static -> static const]
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A null pointer would be passed to a call of the function “of_node_put”
immediately after a call of the function “of_graph_get_next_endpoint”
failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Inside function ctrl_cx2341x_getv4lflags(), qctrl.flag
will be uninitlaized if cx2341x_ctrl_query() returns -EINVAL.
However, it will be used in the later if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A null pointer would be passed to a call of the function "kfree" directly
after a call of the function "kcalloc" failed at one place.
Pass the data structure member "urb" instead for which memory
was allocated before (so that this resource will be properly cleaned up).
This issue was detected by using the Coccinelle software.
Fixes: d571b592c6 ("media: em28xx: don't use coherent buffer for DMA transfers")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On 32-bits archs, a signed integer has 31 bits plus on extra
bit for signal. Due to that, touching the 32th bit with something
like:
int bar = 1 << 31;
has an undefined behavior in C on 32 bit architectures, as it
touches the signal bit. This is warned by cppcheck.
Instead, force the numbers to be unsigned, in order to solve this
issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by cppcheck:
[drivers/media/dvb-frontends/cx24123.c:434]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
[drivers/media/pci/bt8xx/bttv-input.c:87]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
[drivers/media/pci/bt8xx/bttv-input.c:98]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
...
[drivers/media/v4l2-core/v4l2-ioctl.c:1391]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
There are lots of places where we're doing 1 << 31. That's bad,
as, depending on the architecture, this has an undefined behavior.
The BIT() macro is already prepared to handle this, so, let's
just switch all "1 << number" macros by BIT(number) at the header files
with has 1 << 31.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> # exynos4-is and s3c-camif
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # omap3isp, vsp1, xilinx, wl128x and ipu3
Reviewed-by: Benoit Parrot <bparrot@ti.com> # am437x and ti-vpe
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As pointed by cppcheck:
[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour
Prevent mangling with gains with invalid values.
As pointed by Sylvester, this should never happen in practice,
as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16
and m is always >= 0), but it is too hard for a static analyzer
to get this, as the logic with validates control min/max is
elsewhere inside V4L2 core.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While this might not occur in practice, if the device is doing
the right thing, it would be teoretically be possible to have
both hsync_counter and vsync_counter negatives.
If this ever happen, ctrl will be undefined, but the driver
will still call:
aspeed_video_update(video, VE_CTRL, 0, ctrl);
Change the code to prevent this to happen.
This was warned by cppcheck:
[drivers/media/platform/aspeed-video.c:653]: (error) Uninitialized variable: ctrl
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cppcheck incorrectly produces an error here:
[drivers/media/platform/vicodec/vicodec-core.c:1677]: (error) Pointer addition with NULL pointer.
While this is actually a false positive, it doesn't hurt to
reorder the checks to make the code simpler, handling first
the error patch, where no color or alpha components are there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It doesn't make any sense to have gcc's stdarg.h included
inside the Linux Kernel.
Get rid of those includes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As I2C and SPI parts of the V4L2 core got split, let's take
the chance and solve the CodingStyle issues there, as reported
by checkpatch --strict.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, the i2c and spi subdev creation helpers
are calling BUG() when passed a NULL v4l2_device parameter.
This makes little sense; simply returning NULL seems more
sensible.
These two helpers may already return NULL on error, so callers
should already be checking for this, or at least be prepared
for a NULL result.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce a new video4linux2 i2c helper, to unregister a subdev.
This allows to get rid of yet another ifdef.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce a new video4linux2 spi helper, to unregister a subdev.
This allows to get rid of some more ifdefs.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Separate the i2c helpers to v4l2-i2c.c, in order to get rid
of the ifdefery. No functional changes intended, this is
just a cosmetic change to organize the code better.
Given I2C is a tristate symbol, a hidden boolean symbol
is introduced, to make the conditional build easier.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Separate the spi helpers to v4l2-spi.c, in order to get rid
of the ifdefery. No functional changes intended, this is
just a cosmetic change to organize the code better.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
videodev.ko and v4l2-common.ko driver are built under
the same conditions. Therefore, it doesn't make much sense
to split them in two different modules.
Splitting v4l2-common to its own driver was done many years ago:
commit a9254475bb
Author: Mauro Carvalho Chehab <mchehab@infradead.org>
Date: Tue Jan 29 18:32:35 2008 -0300
V4L/DVB (7115): Fix bug #9833: regression when compiling V4L without I2C
Back then, the subsystem organization was different and the module split
was needed. However, with the current organization, there is no issue
compiling V4L2 with I2C as y/m/n.
This commit makes v4l2-common part of our V4L2 core driver (videodev.ko).
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These codes are commented since v4.2-rc1. If there is no plan
to enable the #else part in future, these can be removed
forever.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It returns '0' even when a failure happens on jpeg buffer allocation
so this commit fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
saa7134_i2c_eeprom_md7134_gate() function and the associated comment uses
an inverted i2c gate open / closed terminology.
Let's fix this.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix alignment checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Medion 7134 has two i2c eeproms on the same i2c bus sharing the same bus
addresses: the first one for SAA7134 chip config and the second one behind
TDA10046 DVB-T demod chip i2c gate storing its firmware.
The TV tuner on this board is not behind this i2c gate.
Due to the bus conflict described above, the card PCI SVID / SSID sometimes
gets garbled after a reboot, which makes it necessary to specify the card
model manually as an insmod option in order for it to be detected reliably.
To avoid this, let's just leave the gate permanently closed so the eeprom
chips won't clash.
The demod firmware load is done with its i2c gate closed anyway so it is
not affected by this change.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Variable retval is initialized to a value that is never read
so this assignment is redundant. Clean up the code by removing
retval completely and just return the error return from the
call to i2c_add_adapter.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Like a bunch of other MSI laptops the MS-1039 uses a 0c45:627b
SN9C201 + OV7660 webcam which is mounted upside down.
Add it to the sn9c20x flip_dmi_table to deal with this.
Cc: stable@vger.kernel.org
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If an error occurs in this function, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, introduce two labels to perform
the cleanup work.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In fdp1_open(), 'ctx' is allocated through kzalloc(). However, it is not
deallocated if v4l2_ctrl_new_std() fails, leading to a memory leak bug. To
fix this issue, free 'ctx' before going to the 'done' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In cx231xx_load_firmware(), 'p_buffer' is allocated through vmalloc() to
hold the firmware. However, after the usage, it is not deallocated, leading
to a memory leak bug.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If cec_notifier_cec_adap_unregister() is called before
cec_unregister_adapter() then everything is OK (and this is the
case today). But if it is the other way around, then
cec_notifier_unregister() is called first, and that doesn't
set n->cec_adap to NULL.
So if e.g. cec_notifier_set_phys_addr() is called after
cec_notifier_unregister() but before cec_unregister_adapter()
then n->cec_adap points to an unregistered and likely deleted
cec adapter. So just set n->cec_adap->notifier and n->cec_adap
to NULL for rubustness.
Eventually cec_notifier_unregister will disappear and this will
be simplified substantially.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check if cec_s_conn_info is called with a valid cec adapter,
do nothing if it is invalid.
This makes it possible to call this function even if CEC support is
disabled in the kernel config.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The older CSI drivers have camera capture interface different from the one
in the newer ones.
This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.
[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Makefile and Kconfig for the sun6i CSI driver are included in the main
Makefile / KConfig file. Since we're going to add a new CSI driver for an
older chip, and the Cedrus driver eventually, it makes more sense to put
those in our directory.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of sensor malfunction, stop streaming timeout takes much longer
than expected. This is due to conversion of time to jiffies: milliseconds
multiplied with HZ (ticks/second) gives out a value of jiffies with 10^3
greater. We need to also divide by 10^3 to obtain the right jiffies value.
In other words FRAME_INTERVAL_MILLI_SEC must be in seconds in order to
multiply by HZ and get the right jiffies value to add to the current
jiffies for the timeout expire time.
Fixes: 195ebc43bf ("[media] V4L: at91: add Atmel Image Sensor Interface (ISI) support")
Signed-off-by: Alexandre Kroupski <alexandre.kroupski@ingenico.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function at issue does not always initialize each byte allocated
for 'b' and can therefore leak uninitialized memory to a USB device in
the call to usb_bulk_msg()
Use kzalloc() instead of kmalloc()
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+0522702e9d67142379f1@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Static structure en_templ, of type dvb_ca_en50221, is not used except to
be copied into a local variable. Hence make it const to prevent
unintended modification of the original fields.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The static structure ec168_props, of type dvb_usb_device_properties, is
used only once, when it is assigned to field props of the constant
structure ec168_driver_info. As this means that ec168_props will never be
modified, make it const as well in order to prevent unintended
modification of its fields.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Static structure fdtv_ca, of type dvb_device, is only used when it is
passed as the third argument to function dvb_register_device(). However,
in the definition of dvb_register_device, the third parameter is
declared as constant. Hence make fdtv_ca const as well.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Static structure dst_config, of type dst_config, is not used except to
be assigned as the value of field state of a variable having type
dst_state *. In the definition of dst_state, field config is declared as
const. Hence dst_config, when assigned to config, cannot be modified.
Therefore, make dst_config const as well.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit 5fa88151ec ("[media] dvb-usb-cxusb: Geniatech T230 - resync TS
FIFO after lock") does not solve the problem for all devices. This is the
same issue reported on the T230C, which was moved to the dvbsky.c driver
to work around this issue in commit 5742240577 ("media: dvbsky: MyGica
T230C support").
In addition, the cxusb driver causes an oops when unplugging the device
while streaming; this problem does not happen any more.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove this device from the cxusb driver so it can be added to the dvbsky
driver.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This protocol responds to a real philips rc-mm remote; it does not respond
to IR encoded with the encoder in ir-rcmm-decoder.c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In cx24117_load_firmware(), 'buf' is allocated through kmalloc() to hold
the firmware. However, if i2c_transfer() fails, it is not deallocated,
leading to a memory leak bug.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In dib7000pc_detection(), 'tx' and 'rx' are allocated through kzalloc()
respectively. However, if DiB7000PC is detected, they are not deallocated,
leading to memory leaks. To fix this issue, create a label to free 'tx' and
'rx' before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is a simple NEC remote control device shipped with the HardKernel
ODROID range of SBC devices.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WeTek Play 2 Android STB ships with an unusual remote where the
main up/down/left/right/enter controls are surrounded with an outer
ring of additional keys which are listed in clockwise order.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WeTek Hub Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tanix TX5 max Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tanix TX3 mini Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Khadas VIM and Edge SBC devices use the same NEC remote device. The
remote includes a mouse button for Android use. This has been mapped
to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The X96-Max Android STB ships with a simple NEC remote. It includes
a TV section with preset buttons for controlling a TV. These are not
configurable, but are noted to aid visual recognition of the device.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cmd_init() to fill a struct si2168_cmd command.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
KASAN: global-out-of-bounds Read in dvb_pll_attach
Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).
Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.2.0-rc6+ #13
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
dvb_pll_attach+0x6c5/0x830 drivers/media/dvb-frontends/dvb-pll.c:798
dvb_pll_probe+0xfe/0x174 drivers/media/dvb-frontends/dvb-pll.c:877
i2c_device_probe+0x790/0xaa0 drivers/i2c/i2c-core-base.c:389
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
i2c_new_client_device+0x5b3/0xc40 drivers/i2c/i2c-core-base.c:778
i2c_new_device+0x19/0x50 drivers/i2c/i2c-core-base.c:821
dvb_module_probe+0xf9/0x220 drivers/media/dvb-core/dvbdev.c:985
friio_tuner_attach+0x125/0x1d0 drivers/media/usb/dvb-usb-v2/gl861.c:536
dvb_usbv2_adapter_frontend_init
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:675 [inline]
dvb_usbv2_adapter_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:804
[inline]
dvb_usbv2_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:865 [inline]
dvb_usbv2_probe.cold+0x24dc/0x255d
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:980
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023
generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210
usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_new_device.cold+0x8c1/0x1016 drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x1ada/0x3590 drivers/usb/core/hub.c:5432
process_one_work+0x905/0x1570 kernel/workqueue.c:2269
process_scheduled_works kernel/workqueue.c:2331 [inline]
worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
kthread+0x30b/0x410 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
The buggy address belongs to the variable:
id+0x100/0x120
Memory state around the buggy address:
ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00
ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
^
ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================
Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the venus vdec supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Stateless decoders have different expectations about the
start code that is prepended on H264 slices. Add a
menu control to express the supported start code types
(including no start code).
Drivers are allowed to support only one start code type,
but they can support both too.
Note that this is independent of the H264 decoding mode,
which specifies the granularity of the decoding operations.
Either in frame-based or slice-based mode, this new control
will allow to define the start code expected on H264 slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some stateless decoders don't support per-slice decoding granularity
(or at least not in a way that would make them efficient or easy to use).
Expose a menu to control the supported decoding modes. Drivers are
allowed to support only one decoding but they can support both too.
To fully specify the decoding operation, we need to introduce
a start_byte_offset, to indicate where slices start.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_PIX_FMT_H264_SLICE_RAW name was originally suggested
because the pixel format would represent H264 slices without any
start code.
However, as we will now introduce a start code menu control,
give the pixel format a more meaningful name, while it's
still early enough to do so.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.
The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.
This is not obvious and it normally takes some time to
figure out.
To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is mostly a port of Jacopo's fix:
commit aa4bb8b883
Author: Jacopo Mondi <jacopo@jmondi.org>
Date: Fri Jul 6 05:51:52 2018 -0400
media: ov5640: Re-work MIPI startup sequence
In the OV5645 case, the changes are:
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
Many thanks to Fabio Estevam for his help debugging this issue.
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The omap3isp driver registered subdevs without the dev field being set. Do
that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of blindly trusting getting the clock frequency succeeded end then
testing it against a pre-defined value, verify reading the value
succeeded.
Fixes: 879347f0c2 ("media: ov8856: Add support for OV8856 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a V4L2 sub-device driver for Omnivision ov5675 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[Sakari Ailus: Wrapped a few long lines.]
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 5d7936b8e2 ("media: vsp1: Convert display lists to use new body pool")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the general move to have i2c_new_*_device functions which return
ERR_PTR instead of NULL, this patch converts i2c_new_secondary_device().
There are only few users, so this patch converts the I2C core and all
users in one go. The function gets renamed to i2c_new_ancillary_device()
so out-of-tree users will get a build failure to understand they need to
adapt their error checking code.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> # adv748x
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # adv7511 + adv7604
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # adv7604
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow selecting the IR protocol, MCE or iMON, for a device that
identifies as follows (with config id 0x7e):
15c2:ffdc SoundGraph Inc. iMON PAD Remote Controller
As the driver is structured to default to iMON when both RC
protocols are supported, existing users of this device (using MCE
protocol) will need to manually switch to MCE (RC-6) protocol from
userspace (with ir-keytable, sysfs).
Signed-off-by: Darius Rad <alpha@area49.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
KEY_MAX is not a key but designates the highest value a linux keycode
can ever have.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sometimes the device sends IR data which is all space, no pulses
whatsoever. Add the end of this the driver will put the rc device into
idle mode when it already is in idle mode. The following will be logged:
rc rc0: nonsensical timing event of duration 0
rc rc0: two consecutive events of type space
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
