The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Historically for Rockchip devices we've relied on the power-on
default (or perhaps the firmware setting) to get the correct drive
phase for dw_mmc devices. This worked OK for the most part, but:
* Relying on the setting just "being right" is a bit fragile.
* As soon as there is an instance where the power on default is wrong or
where the firmware didn't configure this properly then we'll get a
mysterious failure.
In commit 7a03fe6f48 ("clk: rockchip: reset init state before mmc card
initialization") we actually started setting this explicitly in the
kernel, but that commit wasn't quite right and also wasn't quite
enough. See <https://patchwork.kernel.org/patch/9085311/> for some
details.
Let's explicitly set this phase in dw_mmc.
The comments inside this patch try to explain the situation quite
throughly, but the high level overview of this is:
Before this patch on rk3288 devices tested (after revert of the clock
patch described above):
* eMMC: 180 degrees
* SDMMC/SDIO0/SDIO1: 90 degrees
After this patch:
* Use 90 degree phase offset usually.
* Use 180 degree phase offset for MMC_DDR52, SDR104, HS200.
That means we are _changing_ behavior for those devices in this way:
* If we have HS200 eMMC or DDR52 eMMC, we'll run ID mode at 90
degrees (vs 180) but otherwise have no change.
* For any non-HS200 / non-DDR52 eMMC devices we'll now _always_ run at
90 degrees (vs 180). It seems fairly unlikely that building modern
hardware is using an eMMC that isn't using DDR52 or HS200, of course.
* For SDR104 cards we'll now run with 180 degree phase offset (vs 90).
It's expected that 90 degree phase offset would have worked OK, but
this gives us extra margin.
I have tested this by inserting my collection of uSD cards (mostly UHS,
though a few not) into a veyron_minnie and confirmed that they still
seem to enumerate properly. For a subset of them I tried putting a
filesystem on them and also tried running mmc_test.
Fixes: 7a03fe6f48 ("clk: rockchip: reset init state before mmc card initialization")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare TRM, BLKSIZ is 16bits.
Then it's correct that max_blk_size should be 0xFFFF, not 0x10000.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some devices connected to the SDHCI controller may have separate enabling
lines that are controlled through GPIO. These devices need to be powered
on and enabled before probing. This is to ensure all devices connected can
be seen by the controller.
Note, for "stable" this patch depends on the following change:
commit 78a898d0e3 ("ACPI / PM: Export acpi_device_fix_up_power()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reported-and-tested-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112571
Link: http://lkml.kernel.org/r/CA+7w51inLtQSr656bJvOjGG9oQWKYPXH+xxDPJKbeJ=CcrkS9Q@mail.gmail.com
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki).
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez).
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada).
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi).
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches).
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat).
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao).
- ACPI cpufreq driver cleanups (Viresh Kumar).
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla).
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann).
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla).
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham).
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King).
- Intel Broxton support for the intel_idle driver (Len Brown).
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach).
- ARM cpuidle cleanups (Jisheng Zhang).
- Intel Kabylake support for the RAPL power capping driver (Jacob Pan).
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner).
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WM89
-----END PGP SIGNATURE-----
Merge tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the cpufreq subsystem this time.
To me, quite obviously, the biggest ticket item is the new "schedutil"
governor. Interestingly enough, it's the first new cpufreq governor
since the beginning of the git era (except for some out-of-the-tree
ones).
There are two main differences between it and the existing governors.
First, it uses the information provided by the scheduler directly for
making its decisions, so it doesn't have to track anything by itself.
Second, it can invoke drivers (supporting that feature) to adjust CPU
performance right away without having to spawn work items to be
executed in process context or similar. Currently, the acpi-cpufreq
driver is the only one supporting that mode of operation, but then it
is used on a large number of systems.
The "schedutil" governor as included here is very simple and mostly
regarded as a foundation for future work on the integration of the
scheduler with CPU power management (in fact, there is work in
progress on top of it already). Nevertheless it works and the
preliminary results obtained with it are encouraging.
There also is some consolidation of CPU frequency management for ARM
platforms that can add their machine IDs the the new stub dt-platdev
driver now and that will take care of creating the requisite platform
device for cpufreq-dt, so it is not necessary to do that in platform
code any more. Several ARM platforms are switched over to using this
generic mechanism.
In addition to that, the intel_pstate driver is now going to respect
CPU frequency limits set by the platform firmware (or a BMC) and
provided via the ACPI _PPC object.
The devfreq subsystem is getting a new "passive" governor for SoCs
subsystems that will depend on somebody else to manage their voltage
rails and its support for Samsung Exynos SoCs is consolidated.
The rest is support for new hardware (Intel Broxton support in
intel_idle for one example), bug fixes, optimizations and cleanups in
a number of places.
Specifics:
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki)
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez)
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada)
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi)
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches)
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat)
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao)
- ACPI cpufreq driver cleanups (Viresh Kumar)
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla)
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann)
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla)
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham)
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King)
- Intel Broxton support for the intel_idle driver (Len Brown)
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach)
- ARM cpuidle cleanups (Jisheng Zhang)
- Intel Kabylake support for the RAPL power capping driver (Jacob
Pan)
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner)
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger)"
* tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (112 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
PM / OPP: Move CONFIG_OF dependent code in a separate file
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
PM / OPP: add non-OF versions of dev_pm_opp_{cpumask_, }remove_table
cpufreq: tango: Use generic platdev driver
PM / OPP: pass cpumask by reference
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpupower: fix potential memory leak
PM / devfreq: style/typo fixes
PM / devfreq: exynos: Add the detailed correlation for Exynos5422 bus
..
Tested on a Salvator-X board with a Spectec SDW-823 WLAN card.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit d6463f170cf0 ("mmc: sdhci: Remove redundant runtime PM calls"),
some of original sdhci_do_xx() function wrappers becomes meaningless,
so remove them.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 61b914eb81f8 ("mmc: sdhci-of-arasan: add phy support for
sdhci-of-arasan") introduce phy support for arasan. According to
the vendor's databook, we should make sure the phy is in poweroff
status before we configure the clk stuff. Otherwise it may cause
some IO sample timing issues from the test. And we don't need this
extra operation while running in low performance mode since phy
doesn't trigger sampling block.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
CC: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
And return the old clock rate if something went wrong.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We had a regression on r8a7740 where the SDHI clock was a generic
peripheral clock, so changing its rate was not desired. This should be
fixed in the clock driver. However, it also shows that the new clock
calculation should only be used on tested systems. Add a check for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RCar Gen2 and later implementations of TMIO/SDHI have their own set of
features and additions. FAST_CLK_CHG is just one of them and I see a few
others being added soon. Some may work on older chipsets but this needs
to be tested case by case. Instead of adding a bunch of flags for each
feature, add a global RCar2+ one for now. We can still break out
features if the need arises.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save a few lines, the codebase is large enough.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller claims to support SDR104. In fact, it only supports a
degraded SDR104 since the maximum frequency of the SD clock is 120 MHz
instead of 208 MHz.
The sdhci core is unaware of it and will compute a wrong clock divider.
We can deal with this specific case by using presets.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some boards need different pin drive strength for the UHS mode. Add an
optional pinctrl setting with two pin states covering UHS speeds and
other speeds.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a start_signal_voltage_switch() operation to support enabling of
UHS modes.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver in its current form does not support UHS at all due to
a missing start_signal_voltage_switch callback.
Also when this callback is added we should let the device tree control
UHS capabilities using the standard mmc bindings.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that reading CTL_STATUS is consistent, we can remove CTL_STATUS2 and
document how this is handled internally.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This bit has a different meaning in SDHI and original TMIO. Document
that and use the proper naming.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent confusion, use the virtual u32 CTL_STATUS in card_busy() the
same way as in other parts of this driver.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BIT() makes it easier to match the bits to the datasheet. This is
especially important here, since some variants have different names in
their datasheets (like with Renesas R-Car).
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Looking at the backlogs, I am not the only one who missed that the above
functions do not read u32 from one register, but create a virtual u32
from reading to adjacent u16 registers (which depending on 'bus_shift'
can be up to 8 byte apart). Because this driver supports old hardware
for which we don't have documentation, I first wrongly assumed there was
a variant which had a few u32 registers. Let's give the functions more
descriptive names to make it more obvious what is happening.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The legacy user space for n900 relies on the MMC slot names.
Let's check if those are passed in pdata and use them.
As this makes the DT booting compatible with legacy booting,
we should be able to start dropping omap3 legacy booting
support in v4.8.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no support for this platform in the kernel anymore.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no support for this platform in the kernel anymore. Make the
Kconfig text more generic, so it won't get stale anymore.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A last minute fix applied by Ulf made room for some simplification.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to have a public and private header file. Merge them
into a private one, so looking up symbols is less confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Having just one irq handler again, let's include the 'card_status'
function in the main handler which is way more readable. Drop a useless
debug output while here. It should be a dev_dbg in case we ever need it
again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We removed installation of separate handlers previously, so we can also
remove the separate handlers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no user left in the kernel, so this code can be removed.
(Legacy, non-DT sh_mobile boards have been removed a while ago.) The
diff looks more complicated than it is: The if-block for multiplexed isr
is now the main code path, the rest is removed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We won't access an index based array to get our DT config, but create
separate structs instead. So, remove the array which only wastes memory.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
defined(CONFIG_MMC_SDHCI_MODULE))
is equivalent to:
defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
defined(MODULE))
and it can also be written shortly as:
IS_REACHABLE(CONFIG_LEDS_CLASS)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_SDR104_NEEDS_TUNING was originally named SDHCI_HS200_NEEDS_TUNING
and was added in commit 069c9f1428 ("mmc: host: Adds support for eMMC
4.5 HS200 mode").
That commit conflated SDHCI_SDR50_NEEDS_TUNING and SDHCI_HS200_NEEDS_TUNING
due to what appears to be misplaced parentheses.
Commit 156e14b126 ("mmc: sdhci: fix caps2 for HS200") made HS200
configuration equivalent to SDR104 configuration, renaming
SDHCI_HS200_NEEDS_TUNING to SDHCI_SDR104_NEEDS_TUNING despite tuning for
HS200 now being non-optional.
The mix-up with SDHCI_SDR50_NEEDS_TUNING remained and became more obvious
after commit 4b6f37d3a3 ("mmc: sdhci: clean up sdhci_execute_tuning()
decision") where the author noted the patch was "reflecting what the
original code was doing, it shows that it may not be what the author
actually intended."
The way the code is currently written, SDHCI_SDR104_NEEDS_TUNING
causes tuning to be done always for SDR50 mode if SDR104 mode is
also supported by the host controller. That makes no sense because
we already have capabilities bit SDHCI_USE_SDR50_TUNING and
corresponding flag SDHCI_SDR50_NEEDS_TUNING for that purpose.
Given the dubious origins of SDHCI_SDR104_NEEDS_TUNING, it seems
reasonable to remove it. The benefit being SDR50 mode will now not
un-nessessarily do tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Swap the call order of sdhci_alloc_host() and platform_get_irq().
It makes sdhci_alloc_host() the last function that can fail in the
sdhci_pltfm_init(). So, we can drop the sdhci_free_host() call from
the failure path.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Call devm_ioremap_resource() right after platform_get_resource().
This saves the error check of platform_get_resource() because
devm_ioremap_resource() checks if the given resource is NULL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The chain of devm_request_mem_region() and devm_ioremap() can be
replaced with devm_ioremap_resource(). Also, we can drop the error
messages because devm_ioremap_resource() displays similar messages
on error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the managed variant of ioremap().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the managed variant of request_mem_region().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function platform_get_irq() can fail; it returns a negative error
code on failure. A negative IRQ number will make sdhci_add_host() fail
to request IRQ anyway, but it makes sense to let it fail earlier here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The requirement resource_size >= 0x100 may not necessarily be
reasonable; for example, sdhci-dove appears to sidestep some
registers in sdhci_dove_readw().
Moreover, current code displays an error message for too small
resource size, but still moves forward.
Every DT should be responsible for describing its properties
correctly, so lets's remove this error message from the common
framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ifdef's make the code more complicated and harder to read.
Move all the LED code together to reduce the ifdef's to
one place.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some error paths in sdhci_add_host() simply returned without
cleaning up. Also the return value from mmc_add_host()
was not being checked.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_AGGRESSIVE_PM for Broxton host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_AGGRESSIVE_PM for Broxton host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk is not used anymore so
remove it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
