The PF driver does not check if the administrator has already set a VF
VLAN via the PF driver before setting the new VLAN. This results in
the following scenario:
A) Administrator sets VF <n> to VLAN 100
B) Administrator sets VF <x> to VLAN 100
C) Administrator sets VF <n> to VLAN 200
D) The VF <n> driver continues to be able to receive traffic on VLAN
100 because the VLVFB pool enable bit for that VF was left set
instead of being cleared as it should be.
This fix ensures that the old VLAN filter for VF <n> is first removed
and the pool bit enable for VF <n> is cleared so that it no longer
receives traffic on VLAN 100.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version number reflect the corresponding functionality in the
out of tree driver.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We reset during the shutdown path which will reset AUTOC register. This
would change LMS to 10G. If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work. For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were only turning the laser on when the adapter was up. This
causes issues for those who wanted to access the MNG FW while the
port was in a down state. This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver to enable certain devices, which have an internal
switch, to read data from the physical slot rather than reading data from the
internal switch. The internal switch will always report the same PCI width and
speed, which is not useful compared to knowing the width and speed of the slot
the physical card is plugged into.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in a follow on patch that needs to convert
between the link_status PCIe config values into ixgbe's internal enum
representations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers. Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset. As a result we were not pulling in TCP headers when the DNF
flag was set.
To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For fdb_add, use the default handler in the non-SRIOV case.
For the other fdb handlers, just remove them and use the
default ones.
CC: John Fastabend <john.r.fastabend@intel.com>
Acked-By: John Fastabend <john.r.fastabend@intel.com>
CC: CC: Gregory Rose <gregory.v.rose@intel.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes have made it so that MAX_SKB_FRAGS is now never less than 16.
As a result we were seeing issues on systems with 64K pages as it would
cause DESC_NEEDED to increase to 68, and we would need over 136 descriptors
free before clean_tx_irq would wake the queue.
This patch makes it so that DESC_NEEDED is always MAX_SKB_FRAGS + 4. This
should prevent any possible deadlocks on the systems with 64K pages as we will
now only require 42 descriptors to wake.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that TXDCTL.WTHRESH is set to 1 when BQL is enabled
and EITR is set to more than 100k interrupts per second to avoid Tx timeouts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for reading data from SFP+ modules over i2c.
Signed-off-by: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces instances where a return code from i2c operations
were checked against a list of error codes with a much simpler
if ( status != 0 ) check.
Some whitespace cleanups included.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that the SW lock is released after all i2c
operations complete in the retry code path.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for the ethtool set_channels operation.
Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the ethtool get_channels operation.
Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_setup_tc code is essentially the same code we need any time we have
to update the number of queues. As such I am making it available always and
just stripping the DCB specific bits out when DCB is disabled instead of
stripping the entire function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue. The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for ixgbe to configure the XPS queue mapping on
load. The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner. This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.
I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs. This essentially treats the two
groupings like they are two separate traffic classes.
In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.
I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64. The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reshuffles the switch/case structure of the flag assignment to
allow for the flags to be set for each MAC type separately. This is needed
for new HW that does not have feature parity with older HW.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTM_GETLINK dump the vlan filter list of a given
bridge port. The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe set gso_size but not gso_type. This leads to
crashes in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects the fact that we were using 1522 to test for the
max frame size in ixgbe_change_mtu and 1518 in ixgbe_set_vf_lpe. The
difference was the addition of VLAN_HLEN which we only need to add in the case
of computing a buffer size, but not a filter size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the rval variable returns from function and replaces
them with direct returns in ixgbe_dcbnl_getnumtcs. It also changes how
ixgbe_gstrings_test is copied into data with memcpy in ixgbe_get_strings
because "*ixgbe_gstrings_test too small (32 vs 160)".
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a default case which goes to the next loop iteration
in the case where p is not set, preventing p from being dereferenced.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.
Based on original patch from Aurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the autoneg parameter from the setup_link functions.
Adds local variable autoneg to setup_link functions to be passed
to get_link_capabilities functions if needed.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Removes the autoneg parameter from the setup_link_speed functions. These
functions do nothing with this parameter.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device lookup neglected to do a pci_dev_put() to decrement the
device reference count.
Reported-by: Elena Gurevich <elena.gurevich@toganetworks.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for up2tc change and call ixgbe_dcbnl_devreset() if the mapping has
changed but the number of TC's in use has not changed.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63. Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for enable/disable of SR-IOV via the PCI sysfs interface
move some core SR-IOV enablement code that would be common to module
parameter usage or callback from the PCI bus driver to a separate
function so that it can be used by either method.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally. Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to inline the Rx PTP descriptor handling. The main
motivation is to avoid unnecessary jumps into function calls that we then
immediately exit because we are not performing timestamps.
The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU
utilization in my performance runs to 0%, and the only value tested is the Rx
descriptor which should already be warm in the cache if not stored in a
register.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.
This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.
To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.
If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the comment on ptp_overflow_check to match up with what is
currently used as the parameters. Also change the jiffies check to use
time_is_after_jiffies macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the filters for ethtool's get_ts_info to return support for
all filters which can be supported by upscaling to ptp_v2_event. The intent
behind this change is due to reasoning that we do in fact support the
filters. (hwtstamp_ioctl returns success after setting the filter to the
upscaled version). In this way we can remain consistent over which filters are
supported via the get_ts_info ioctl and which filters are in practice actually
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the ethtool diagnostics test by ensuring that the tests
work properly regardless of what state the adapter was in. The SRIOV VF check is
done at the beginning, forgoing the link test. The if_running -> dev_close is
moved before the link test, as well as a call to enable the Tx laser. This
ensures that the link test will return valid results even when adapter was
previously down. Also, a call to disable the Tx laser is added if the device
was down before the start. This ensures consistent behavior of the Tx laser
before and after the diagnostic checks. The end result is consistent behavior
regardless of device state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map. To do this I have expanded the work done in the main loop by
pushing first into tx_buffer. This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor. The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo. By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.
To do this I also needed to change the logic and/or drop some flags. I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do. Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb. Instead we can just check the bitflag in the skb.
In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway. Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads. Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.
With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X540's internal thermal sensor should not be enabled for all devices, but
only those devices which enable it in the NVM image. It is expected that
actively cooled devices will have it enabled, but passively cooled devices might
not want it enabled. This is due to passively cooled devices operating very near
the thermal threshold, sometimes within the margin of error of the thermal
sensor. Thus these devices may not be good candidates for using the thermal
sensor.
This patch uses the enabled bit in the FWSM register to check whether we should
be enabling the thermal sensor, and only sets the THERMAL_SENSOR_CAPABLE flag
for those devices which have it enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the normal kernel test instead of a module specific one.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled. Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces calls to copy_to_user, copy_from_user, and the associated
logic, with calls to simple_read_from_buffer and simple_write_to_buffer
respectively. This was done to eliminate warnings generated by the Smatch
static analysis tool.
v2- Fix return values based community feedback
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the version string to better reflect the driver functionality with
that of the out of tree driver. Also since we no longer need the MAJ,
MIN, BUILD defines remove them to clean up the code.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The internal bridge mode setting needs to be sticky so that it can be
configured correctly after a device reset. This change is required now
that the driver supports setting the bridge mode to VEB or VEPA.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XOFF received statistic registers are per priority based and not per
traffic class. The ixgbe driver was incorrectly considering them to be for
each traffic class; and then disabling the "Tx hang" check for the queues
that belonged to the particular traffic class that had received PFC frames.
The above logic worked fine in scenario where the user priority and traffic
class number matched e.g. priority 0 is mapped to traffic class 0 and so on.
But, when multiple user priorities are mapped to a single traffic class or
when user priorities and traffic class numbers do not line up; the ixgbe
driver may disable the "Tx hang" check for queues belonging to a traffic
class that did not receive PFC frames and keep the "Tx hang" check enabled
for the queues that did receive the PFC frames.
This patch corrects the above in the code by considering the statistics
on a per priority basis; then getting the traffic class the user priority
belongs to and disabling the "Tx hang" check for queues that belong
to that traffic class.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are doing a page based receive there is no point in setting a maximum
packet length on the x540 RXDCTL register. As such we can drop the code from
the driver entirely.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.
This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.
This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.
I am going to chalk this up as a bug and fix it now.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.
There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the queuing that was previously done for L4 packets
as it is not needed. The filter does not provide functionality, and it
is possible that queue setup here could trample settings done else-where
in the driver. (for example it may use a queue which isn't setup.)
Setting of the queue is not required for hardware timestamping and could
have inadverdent side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes a magic number that was used for the ETQF used for
filtering L2 ptp packets and replaces it with the supplied define that
previously existed. The intent is to clarify that this filter is already
set aside for L2 1588 work.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reformats the output of the Tx/Rx descriptor dumps to more
appropriately align the output of the ixgbe_dump and improve readability.
Prevents empty Tx descriptors from being displayed to decrease the size
of the dump and make it more manageable.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way the code was previously written it was causing DCA to prefetch the
entire packet into the cache when it was enabled. That is excessive as we
only really need the headers.
We are now prefetching the headers via software so doing this from DCA would
be redundant anyway. So clear the bit that was causing us to prefetch the
packet data and instead only use DCA for the descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb, ixgbe and e1000.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:
- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
as part of net driver modules. (This also fixes cases where the PTP
subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
drivers but are built separately
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The q_vector->itr check in ixgbe_configure_tx_ring() was done prior to it
being set, which resulted in TXDCTL.WTHRESH always being set to 1 on driver
load, while consequent resets would set it to 8.
This patch moves the setting of q_vector->itr in ixgbe_alloc_q_vector() to
make sure that TXDCTL.WTHRESH is set to 8 by default.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug in ixgbe_ptp_check_pps_event where the type was
uninitialized and could cause unknown event outcomes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe, ixgbevf, igbvf, igb and
networking core (bridge). Most notably is the addition of support
for local link multicast addresses in SR-IOV mode to the networking
core.
Also note, the ixgbe patch "ixgbe: Add support for pipeline reset" and
"ixgbe: Fix return value from macvlan filter function" is revised based
on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the net device ops to manage the embedded
hardware bridge on ixgbe devices. With this patch the bridge
mode can be toggled between VEB and VEPA to support stacking
macvlan devices or using the embedded switch without any SW
component in 802.1Qbg/br environments.
Additionally, this adds source address pruning to the ixgbevf
driver to prune any frames sent back from a reflective relay on
the switch. This is required because the existing hardware does
not support this. Without it frames get pushed into the stack
with its own src mac which is invalid per 802.1Qbg VEPA
definition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hw timestamping code caused performance regression in ixgbe driver when the
timestamping is not enabled. The culprit is IXGBE_READ_REG call in the Rx
path which is executed for every received skb. This call is not needed when
the timestamping is disabled or for non-ptp packets.
netperf results:
The ixgbe side of the connection was acting as a server, the netperf command
line on the other side was:
netperf -H 192.168.1.23 -T0,0 -t UDP_STREAM -l 20
The values below mean throughput as reported by netperf (local/remote), for
3 runs, with timestamping not enabled.
3.7.0-rc1+ with CONFIG_IXGBE_PTP off:
5373.83 / 3329.32
5721.88 / 3033.89
5653.42 / 3112.38
3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5233.64 / 1226.85
5448.67 / 1039.32
5421.36 / 1095.66
Patched 3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5594.72 / 2942.53
5428.95 / 3110.16
5343.56 / 3200.48
Reported-by: Jesper Brouer <jbrouer@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds/updates ASCII descriptor maps for 82598 and 82599 Tx/Rx descriptors.
Current descriptor maps were out of date for 82598 and incorrect for
82599.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that compare the total_rx_packets cleaned to budget
instead of decrementing budget. The advantage to this approach is that budget
can now be const and we only end up modifying total_rx_packets instead of
modifying both it and budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting a MAC filter for the VF the function should return a success
or failure code, not the index of the new filter. It causes spurious NACK
returns to the VF driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the check for calling en/disable_tx_laser() function
pointer. The pointer is only set on parts that can use it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SR-IOV mode the PF driver acts as the uplink port and is
used to send control packets e.g. lldpad, stp, etc.
eth0.1 eth0.2 eth0
VF VF PF
| | | <-- stand-in for uplink
| | |
--------------------------
| Embedded Switch |
--------------------------
|
MAC <-- uplink
But the embedded switch is setup to forward multicast addresses
to all interfaces both VFs and PF and onto the physical link.
This results in reserved MAC addresses used by control protocols
to be forwarded over the switch onto the VF.
In the LLDP case the PF sends an LLDPDU and it is currently
being forwarded to all the VFs who then see the PF as a peer.
This is incorrect.
This patch adds the multicast addresses to the RAR table in the
hardware to prevent this behavior.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function to set the macvlan filter should return success or failure
instead of the index of the filter. The message processing function was
misinterpreting the index as a non-zero return code indicating failure and
NACKing MAC filter set messages that actually succeeded.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline
reset on all 82599 devices. This is necessary to avoid possible link issues.
Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap
all AUTOC writes when LESM is enabled.
v2- fix LMS behaviour based on feedback by Martin Josefsson
CC: Martin Josefsson <gandalf@mjufs.se>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were not correctly freeing the temporary rings on error in
ixgbe_set_ring_param. In order to correct this I am unwinding a number of
changes that were made in order to get things back to the original working
form with modification for the current ring layouts.
This approach has multiple advantages including a smaller memory footprint,
and the fact that the interface is stopped while we are allocating the rings
meaning that there is less potential for some sort of memory corruption on the
ring.
The only disadvantage I see with this approach is that on a Rx allocation
failure we will report an error and only update the Tx rings. However the
adapter should be fully functional in this state and the likelihood of such
an error is very low. In addition it is not unreasonable to expect the
user to need to recheck the ring configuration should they experience an
error setting the ring sizes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function that forces a full pipeline reset. This
function will be used in following patches to completely reset the PHY
during resets.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We still had some code floating around from the old single buffer receive
path. As a result we were adding VLAN_HLEN to max_frame although the
resultant value was never used. Since that is the case we can drop this from
the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver pad skb up to 17 bytes because of the HW requirement. However, that code
implementation mess up the skb tail pointer after padding. This patch sets
skb->tail correctly.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using is_zero_ether_addr() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies when and where PTP registers and data are set. Previously
a work-around was used inside cyclecounter_start in order to reset some of the
time registers. This patch creates a new ixgbe_ptp_reset specifically for this
purpose. The cyclecounter configuration has trimmed down to only modify what
is necessary. Due to hardware conditions after probe and before open, PTP init
has now moved into the ixgbe_open call. This allows the ptp device name in the
sysfs to be the ethernet device name instead of the MAC address.
The cyclecounter check flag is renamed to PTP_ENABLED and is used to prevent
PTP init from happening when PTP has not been enabled.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a subdevice id for new 82599 device. The define is needed
to allow enabling WOL support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change switches on the last few bits for us enabling version 1.1 VF
support in the PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues in regards to the combination of DCB
and SR-IOV. Specifically it allows us to send information to the VF on
which queues it should be using.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is necessary to track the default user priority in the PF so that we can
force it upon the VFs. The motivation behind this is to keep the VFs from
getting access to user priorities meant for things like storage.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for IPv6 and UDP to ixgbe_get_headlen. The
advantage to this is that we can now handle ipv4/UDP, ipv6/TCP, and
ipv6/UDP with a single memcpy instead of having to do them in multiple
pskb_may_pull calls.
A quick bit of testing shows that we increase throughput for a single
session of netperf from 8800Mpbs to about 9300Mpbs in the case of ipv6/TCP.
As such overall ipv6 performance should improve with this change.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows us to add a mailbox versioning API. This will allow us
to determine the features supported by the VFs from the PF. For example we
will be implementing a version 1.1 API for the VF that will indicate that
it can support us enabling Jumbo frames as the VF will support buffer
chaining.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of trying to maintain one large monolithic function that handles
most of the different messages from the VF it makes sense to break the
message handling function up so that we can just go through one switch
statement and call the correct routine for a given message.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can have limited support for jumbo frames
when SR-IOV is enabled. In order to accomplish this it is necessary to
disable all VFs when the PF has jumbo frames enabled. If the VFs then
request the same maximum frame size as the PF they will be re-enabled. A
follow on patch will add a means of identifying when a VF can support
spanning buffers and does not need to be worried about the actual supported
max frame size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling DCB the rings belonging to a q_vector on CPU 0 were not
reinitializing their DCA registers. Upon closer inspection the issue was
that the q_vector CPU variable was left at 0 resulting in the driver not
updating the DCA registers.
In order to guarantee the DCA registers will be updated I am adding a
couple line change so that we initialize the CPU variable to -1 which will
force a DCA update the first time an interrupt fires on that q_vector.
In addition we were setting the CPU affinity hint to all CPUs when we were
not specifying a CPU. Instead we should leave it as all zeros to avoid any
possible confusion about the fact that we shouldn't be giving a hint.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change limits the PF/VF driver to 9.5K max jumbo frame size in order
prevent a possible Tx hang in the adapter when sending frames between
pools.
All of the parts in ixgbe support a maximum frame of 15.5K for standard
traffic, however with SR-IOV or DCB enabled they should be limiting the
MTU size to 9.5K. Instead of adding extra checks which would have to
change the MTU when we go into or out of these modes it is preferred to
just use a standard 9.5K MTU limit for all modes so that this extra
overhead can be avoided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds device support for Ethernet Controller X540-AT1.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The loop in ixgbe_reinit_fdir_tables_82599() only polls for up to 100us
resulting in failures to update the FDIR filter table at 1Gbps and 10Gbps
when under load.
The poll times for FDIRCTRL.INIT_DONE are 55us, 550us and 5.5ms for 10Gbps,
1Gbps and 100Mbps respectively.
This patch sets the wait time to be the same as in ixgbe_fdir_enable_82599()
Reported-by: Bhushan <shashi-sm@users.sf.net>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a development issue that occurred due to invalid modes reported
in the ethtool get_ts_info function. The issue is resolved by removing
unsupported modes from the Rx supported list.
CC: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was enabling PPS interrupt even when user wasn't enabling it via the
ptp core. This patch fixes the PPS so that it is only enabled explicitly, and
moves the interrupt enabling code into the correct location in the driver
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug in the method used for calculating the trigger
alignment for SDP0 when enabling a PPS output on the X540. The alignment math
wasn't properly taking into account the overflow cyclecounter, and was
misaligning the pin triggers so that two X540 devices synced properly had
mis-aligned SDP pins. This patch fixes the math to calculate the correct
seconds alignment for the PPS signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Later changes need to be able to refer to neighbour attributes
when doing fdb_add.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter is not valid unless the controller is running in IOV mode.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal functions for add/deleting addresses don't change
their argument.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that the byte and packet count statistics are under-
counting traffic handled by the DDP offload when there is more
than one DDP completion processed in a single call to
ixgbe_clean_rx_irq. This patch fixes that.
I tried to optimize the setting of the rss value so that it
only would have to be computed once, and only when there is
a DDP completion present.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the reg_ops file to debugfs with commands to read and write
a register to give users the ability to read and write individual
registers on the fly.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the netdev_ops file to debugfs with a command to call the
ndo_tx_timeout function to give users the ability to simulate a
tx_timeout call made by the kernel.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds debugfs support to the ixgbe driver to give
users the ability to access kernel information and to
simulate kernel events.
The filesystem is set up in the following driver/PCI-instance
hierarchy:
<debugfs>
|-- ixgbe
|-- PCI instance
| |-- attribute files
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use %u instead of %d to display u32 variable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes the assumptions of the rate limiting code that previously
assumed that each VF would only ever have 2 queues. This update makes it
so that we now use a queues per pool value that is determined based on the
VMDq feature mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-By: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF was not correctly registering any of its VLANs. As a result any
VLAN tagged traffic from the VF would not be delivered to the PF because
the VLAN was never assigned to the PF pool.
In addition the VF was not allowed to receive traffic from VLAN 0 if it was
allowed to receive untagged frames. This change corrects that so that it
will correctly receive traffic from VLAN 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
Remove a for loop that does nothing in ixgbe_probe().
This is a remnant from when we had IO bars (compare to the ixgb code).
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This change updates the code related to configuring the transmit frame
checksum. Specifically I have updated the code so that we can only skip
inserting the checksum in the case that we are not performing some other
offload that will modify the frame data.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change moves the RSC code into the non-EOP descriptor handling
function. The main motivation behind this change is to help reduce the
overhead in the non-RSC case. Previously the non-RSC path code would
always be checking for append count even if RSC had been disabled. Now
this code is completely skipped in a single conditional check instead of
having to make two separate checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch creates a function named ixgbe_fetch_rx_buffer. The sole
purpose of this function is to retrieve a single buffer off of the ring and
to place it in an skb.
The advantage to doing this is that it helps improve the readability since
I can decrease the indentation and for the code in this section.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change makes it so that if only the first 256 bytes of a buffer are
used we just copy the data out and leave the offset and page count
unchanged. There are multiple advantages to this. First it allows us to
reuse the page much more in the case of pages larger than 4K. It also
allows us to avoid some expensive atomic operations in the form of
get_page/put_page. In perf I have seen CPU utilization for put_page drop
from 3.5% to 1.8% as a result of this patch when doing small packet routing,
and packet rates increased by about 3%.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change creates a separate function for functionality similar to
pskb_pull_tail. The main motivation for moving it to a separate function
is so that later I can just skip this function in the case where we have
already copied the buffer into skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch makes it so that we will always have ownership of the buffers by
the time we get to ixgbe_add_rx_frag. This is necessary as I am planning to
add a copy-break to ixgbe_add_rx_frag and in order for that to function
correctly we need the CPU to have ownership of the buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change makes it so that we do not use double buffering if the page
size is larger than 4K. Instead we will simply walk through the page using
up to 3K per receive, and if we receive less than we only move the offset
by that amount. We will free the page when there is no longer any space
left that we can use instead of checking the page count to see if we can
cycle back to the start.
The main motivation behind this is to avoid the unnecessary truesize cost
for using a half page when most packets are 2K or smaller. With this new
approach the largest possible truesize for a page fragment will be 3K when
PAGE_SIZE is larger than 4K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch combines ixgbe_add_rx_frag and ixgbe_can_reuse_page into a
single function. The main motivation behind this is to make better use of
the values so that we don't have to load them from memory and into
registers twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change reverts an earlier patch that introduced
ixgbe_init_rx_page_offset. The idea behind the function was to provide
some variation in the starting offset for the page in order to reduce
hot-spots in the cache. However it doesn't appear to provide any
significant benefit in the testing I have done. It has however been a
source of several bugs, and it blocks us from being able to use 2K
fragments on larger page sizes. So the decision I made was to remove it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Sascha Wildner <saw@online.de>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used. If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.
It works by reintroducing and expanding the skb_alloc_page() API to take
an skb. If the page was allocated from pfmemalloc reserves, it is
automatically copied. If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.
Failure to do so is not critical. The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.
[davem@davemloft.net: API rename and consistency]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch makes use of skb->data on Tx and the virtual address of the pages
allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
