When using the S/PDIF DAI, there is no requirement to call
snd_soc_dai_set_fmt() as there is no DAI format definition that defines
S/PDIF. In any case, S/PDIF does not have separate clocks, this is
embedded into the data stream.
Consequently, when attempting to use TDA998x in S/PDIF mode, the attempt
to configure TDA998x via the hw_params callback fails as the
hdmi_codec_daifmt is left initialised to zero.
Since the S/PDIF DAI will only be used by S/PDIF, prepare the
hdmi_codec_daifmt structure for this format.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an entry to the quirks-table to for usb-audio to recognize the
Microbook II (although it only exposes vendor interfaces). A simple boot
quirk is also implemented to set up the sample rate and make sure that
no audio urbs are sent before the device is ready.
This patch only provides audio playback and capture at 96kHz sample
rate. Notice the following shortcomings:
- The sample rate is currently hardcoded to 96k although the device also
supports 48k and 44.1k.
- The various mixer controls of the MicroBook are not made available.
- The keep-iface control should be on by default because the device
shuts down whenever the altsetting is reset which is usually unwanted.
(I don't know the best way to do this)
- The communication format used by the MicroBook for sample rate setting
and also other setup has been reverse engineered by looking at the
usbmon output while running the windows driver through virtualbox. In
this patch the first byte of every message is set to \0 while in the
observed communications the first byte acts as a "message-counter"
increasing its value with every message sent. Leaving it at \0 does
not seem to affect the device.
Signed-off-by: Manuel Reinhardt <manuel.rhdt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes a bug that prevents freeing the reset gpio on unloading
the module.
aic3x_i2c_probe is called when loading the module and it calls list_add
with a probably uninitialized list entry aic3x->list (next = prev = NULL)).
So even if list_del is called it does nothing and in the end the gpio_reset
is not freed. Then a repeated module probing fails silently because
gpio_request fails.
When moving INIT_LIST_HEAD to aic3x_i2c_probe we also have to move
list_del to aic3x_i2c_remove because aic3x_remove may be called
multiple times without aic3x_i2c_remove being called which leads to
a NULL pointer dereference.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx3z7ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H5QB/9jwKEwOdk6ynoFUpQwXPPkQl7CGkIh
P8J3OMTt+U4FNOrVG2S7xgUl69ZoaLm9rS/PHVrMV5krSLqY//2CTvF068qDBBlj
haBxgeRbe4pwLZPfFUnWvn6v1rdvNCXzDG/be9jGPJjDcm6wK44VJQWkPbqTsh6O
ZORqvKn48D89W0DegG1B+4jvbietPkhA0+nHQXwsWZ+sfMcEV/AWWsE5FIQ7ucCC
bundBBncUFKMMp9whuhj2W9FO62LUd8OAM7ejis3hfKk9MsQWUy6vrcN1XgRCq47
4I0doB5o+WhsOGMTZMcuhFISCVaCDqbNqGuVbeK0sdonjc1xz0682jLo
=9rq8
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More changes for v5.1
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
Dummy write in capture master mode is used to gate
bus clocks. This write is useless in slave mode
as the clocks are not managed by slave.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_pcm_stop_xrun() is called in interrupt routine,
substream context may have already been released.
Add protection on substream context.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clocks do not need to be released on driver removal,
as this is already managed before.
Remove useless remove callback.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA configuration is not balanced on start/stop.
Move DMA configuration to trigger callback.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move counter handling to trigger start section
to manage multiple start/stop events.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S supports 16 bits data in 32 channel length.
However the expected driver behavior, is to
set channel length to 16 bits when data format is 16 bits.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because of regmap cache, interrupts may not be cleared
as expected.
Declare IFCR register as write only and make writings
to IFCR register unconditional.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_CROS_EC_CODEC depends on MFD_CROS_EC.
Add that dependency to SND_SOC_SDM845 to fix unmet direct dependencies
warning.
Fixes: 74c6ecf419 (ASoC: qcom: Kconfig: select dmic for sdm845)
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch enables the reuse of kbl_da7219_max98927 machine driver to
support max98373. The same machine driver is modified for cases where one
amplifier is swapped out with another. Most of the changes are about
renaming the codec and codec_dai names, with minor differences due to
support for 24 bits in one case and 16 in the other.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently each SSI unit 's busif mode/adinr/dalign address is
registered by: (in busif4 case)
RSND_GEN_M_REG(SSI_BUSIF4_MODE, 0x500, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_ADINR,0x504, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_DALIGN, 0x508, 0x80)
But according to user manual 41.1.4 Register Configuration
ssi9 4/5/6/7 busif mode/adinr/dalign register address
( SSI9-[4/5/6/7]_BUSIF_[MODE/ADINR/DALIGN] )
are out of this rule.
This patch registers ssi9 4/5/6/7 mode/adinr/dalign register
as single register, and access these registers in case of
SSI9 BUSIF 4/5/6/7.
Fixes: commit 8c9d750333 ("ASoC: rsnd: ssiu: Support BUSIF other than BUSIF0")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In data blocks of common isochronous packet for MOTU devices, PCM
frames are multiplexed in a shape of '24 bit * 4 Audio Pack', described
in IEC 61883-6. The frames are not aligned to quadlet.
For capture PCM substream, ALSA firewire-motu driver constructs PCM
frames by reading data blocks byte-by-byte. However this operation
includes bug for lower byte of the PCM sample. This brings invalid
content of the PCM samples.
This commit fixes the bug.
Reported-by: Peter Sjöberg <autopeter@gmail.com>
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 4641c93940 ("ALSA: firewire-motu: add MOTU specific protocol layer")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I set 10 seconds for the timeout of the i915 audio component binding
with a hope that recent machines are fast enough to handle all probe
tasks in that period, but I was too optimistic. The binding may take
longer than that, and this caused a problem on the machine with both
audio and graphics driver modules loaded in parallel, as Paul Menzel
experienced. This problem haven't hit so often just because the KMS
driver is loaded in initrd on most machines.
As a simple workaround, extend the timeout to 60 seconds.
Fixes: f9b54e1961 ("ALSA: hda/i915: Allow delayed i915 audio component binding")
Reported-by: Paul Menzel <pmenzel+alsa-devel@molgen.mpg.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the compressed stream implementation has acquired support for
multiple DAI links and compressed streams it has become harder to
interpret messages in the kernel log. Add additional macros to include
the compressed DAI name in the log messages, allowing different streams
to be easily disambiguated.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, only a single compressed stream is supported per firmware.
Add support for multiple compressed streams on a single firmware, this
allows additional features like completely independent trigger words or
separate debug capture streams to be implemented.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the code slightly clearer and prepare things for the addition of
multiple compressed streams on a single DSP core.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for more refactoring add a helper function to strip the
padding from ADSP data.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The irq_get_irq_data() function doesn't return error pointers, it
returns NULL.
Fixes: 6ba9dd6c89 ("ASoC: cs35l36: Add support for Cirrus CS35L36 Amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A platform can have multiple sound cards for different audio paths.
Following is the print seen duirng device boot for jetson-xavier,
ALSA device list:
#0: nvidia,p2972-0000 at 0x3518000 irq 17
By looking at above, it is not very clear if the sound card is for
HDA. It becomes confusing when platform has registered multiple cards,
and platform model name is used for card.
This patch uses "nvidia,model" property mentioned in hda device tree
to get the card name. Since property is optional, legacy boards will
continue to use "tegra-hda". Custom name can be passed wherever needed.
This naming convention is conistent with the way sound cards are named
in general.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS UX362FA with ALC294 cannot detect the headset MIC and outputs
through the internal speaker and the headphone. This issue can be fixed
by the quirk in the commit 4e0511067 ALSA: hda/realtek: Enable audio
jacks of ASUS UX533FD with ALC294.
Besides, ASUS UX362FA and UX533FD have the same audio initial pin config
values. So, this patch replaces SND_PCI_QUIRK of UX533FD with a new
SND_HDA_PIN_QUIRK which benefits both UX362FA and UX533FD.
Fixes: 4e05110673 ("ALSA: hda/realtek: Enable audio jacks of ASUS UX533FD with ALC294")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Ming Shuo Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This addresses an issue pointed out by compiler warning:
sound/soc/samsung/odroid.c: In function ‘odroid_audio_probe’:
sound/soc/samsung/odroid.c:298:22: warning: ‘cpu_dai’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
priv->clk_i2s_bus = of_clk_get_by_name(cpu_dai, "iis");
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need 32ea33a044 ("mei: bus: export to_mei_cl_device for mei
client devices drivers") for the mei-hdcp patches.
References: https://lkml.org/lkml/2019/2/19/356
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Here are a few last-minute fixes for 5.0. The most significant one
is the OF-node refcount fix for ASoC simple-card, which could be
triggered on many boards. Another fix for ASoC core is for the
error handling in topology, while others are device-specific fixes
for Samsung and HD-audio.
-----BEGIN PGP SIGNATURE-----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=xyOI
-----END PGP SIGNATURE-----
Merge tag 'sound-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few last-minute fixes for 5.0.
The most significant one is the OF-node refcount fix for ASoC
simple-card, which could be triggered on many boards. Another fix for
ASoC core is for the error handling in topology, while others are
device-specific fixes for Samsung and HD-audio"
* tag 'sound-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: simple-card: fixup refcount_t underflow
ASoC: topology: free created components in tplg load error
ALSA: hda/realtek: Disable PC beep in passthrough on alc285
ALSA: hda/realtek - Headset microphone and internal speaker support for System76 oryp5
ASoC: samsung: i2s: Fix prescaler setting for the secondary DAI
Although qcom_snd_parse_of() tries to manage the of-node refcount,
there are still a few places that lead to the unblanced refcount in
the error code path. Namely,
- for_each_child_of_node() needs to unreference the iterator node if
aborting the loop in the middle,
- cpu, codec and platform node objects have to be unreferenced at each
iteration,
- platform and codec node objects have to be referred before jumping
to the error handling code that unreference them unconditionally.
This patch tries to address these by moving the assignment of platform
and codec node objects to the beginning of the loop and adding the
of_node_put() calls adequately.
Fixes: c25e295cd7 ("ASoC: qcom: Add support to parse common audio device nodes")
Cc: Patrick Lai <plai@codeaurora.org>
Cc: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The apq8016 driver leaves the of-node refcount at aborting from the
loop of for_each_child_of_node() in the error path. Not only the
iterator node of for_each_child_of_node(), the children nodes referred
from it for codec and cpu have to be properly unreferenced.
Fixes: bdb052e81f ("ASoC: qcom: add apq8016 sound card support")
Cc: Patrick Lai <plai@codeaurora.org>
Cc: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In odroid_audio_probe() some OF nodes are left without reference count
decrease after use. Fix it by ensuring required of_node_calls() are done
before exiting probe.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dell Precision 5820 with ALC3234 codec (which is equivalent with
ALC255) shows click noises at (runtime) PM resume on the headphone.
The biggest source of the noise comes from the cleared headphone pin
control at resume, which is done via the standard shutup procedure.
Although we have an override of the standard shutup callback to
replace with NOP, this would skip other needed stuff (e.g. the pull
down of headset power). So, instead, this "fixes" the behavior of
alc_fixup_no_shutup() by introducing spec->no_shutup_pins flag.
When this flag is set, Realtek codec won't call the standard
snd_hda_shutup_pins() & co. Now alc_fixup_no_shutup() just sets this
flag instead of overriding spec->shutup callback itself. This allows
us to apply the similar fix for other entries easily if needed in
future.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function simple_for_each_link() has a few missing places that
forgot unrefereing of-nodes after the use. The main do-while loop
may abort when loop=0, and this leaves the node object still
referenced. A similar leak is found in the error handling of NULL
codec that aborts the loop as well. Last but not least, the inner
for_each_child_of_node() loop may abort in the middle, and this leaks
the refcount of the iterator node.
This patch addresses these missing refcount issues.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We forgot to unreference the platform node object obtained from
of_get_child_by_name(). This leads to the unbalance of node
refcount.
Fixes: e0ae225b7e ("ASoC: simple-card: support platform in dts parse")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The node obtained from of_find_node_by_path() has to be unreferenced
after the use, but we forgot it for the root node.
Fixes: f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support")
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, compressed buffers can only be specified in the XM memory
region. There is no reason to have such a restriction with the newer
meta-data based way of specifying the buffers, so remove it.
Signed-off-by: Andrew Ford <aford@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a compressed stream is restarted after getting an error, the cached
error value will still be used on the next pointer request, preventing
the stream from starting. Resolve this by ensuring the error status is
updated on trigger start.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We forgot to unreference the node when aborting from the loop of
for_each_child_of_node() in snd_pmac_tumbler_init(). This leads to
unbalanced node refcount. Fix it by adding the missing of_node_put()
call.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We forgot to unreference a node obtained via of_find_node_by_name()
after its usage.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ac97_of_get_child_device() take the refcount of the node explicitly
via of_node_get(), but this leads to an unbalance. The
for_each_child_of_node() loop itself takes the refcount for each
iteration node, hence you don't need to take the extra refcount
again.
Fixes: 2225a3e6af ("ALSA: ac97: add codecs devicetree binding")
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ADCs are sleeping when the SLEEP bit is set and running when it's
cleared, so the bit should be inverted.
Tested on pcm1863.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
According to DS, the gain is between -12 dB and 40 dB, with a 0.5 dB step.
Tested on pcm1863.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On some SoCs (e.g. Exynos5433) there are multiple "IIS multi audio
interfaces" and the driver will try to register there multiple times
same platform device for the secondary FIFO, which of course fails
miserably. To fix this we derive the secondary platform device name
from the primary device name. The secondary device name will now
be <primary_dev_name>-sec instead of fixed "samsung-i2s-sec".
The fixed platform_device_id table entry is removed as the secondary
device name is now dynamic and device/driver matching is done through
driver_override.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes unregistration of the secondary platform device so all
resources are properly released. Additionally the removal sequence
is corrected so it is in reverse order comparing to probe sequence.
The test against NULL priv->pdev_sec is removed as it is not necessary.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add FE DAI link to support parallel playback on 2 ports
simultaneously.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch enables support for GeminiLake with the DA7219 codec and
MAX98357A amplifier. To avoid duplicating code, the existing machine
driver for ApolloLake is reused with only changes in hardware
connectivity (SSP2 for DA7219 and SSP1 for MAX98357A).
The dailinks are directly modified in this patch. Using a helper would
be nicer, but it'll be done in a follow-up step with validation done
across multiple machine drivers.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet, bindings, and the subject
from the original commit.
Fixes: ca0412a057 ("ASoC: sunxi: sun50i-codec-analog: Add support for cpvdd regulator supply")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If platform_data is NULL add reading of optional adi,micbias
property from DT. If adi,micbias is not set keep the default
value for micbias.
Signed-off-by: Bogdan Togorean <bogdan.togorean@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should free "w" on the error path.
Fixes: 199ed3e81c ("ASoC: dapm: fix use-after-free issue with dailink sname")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With old DTS there will be missing DAPM routes linking BE with CODECs.
Add those routes in the card driver so sound works properly on Odroid
XU3/4 also without DTS updates enabling the secondary PCM.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
sound/soc/codecs/wm8741.c:371:5: warning:
symbol 'wm8741_mute' was not declared. Should it be static?
Fixes: 36b1599340 ("ASoC: wm8741: Add digital mute callback")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ESAI_xCR_xWA is xCR's bit, not the xCCR's bit, driver set it to
wrong register, correct it.
Fixes 43d24e76b6 ("ASoC: fsl_esai: Add ESAI CPU DAI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ackedy-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A few small fixes, a driver fix for Samsung, a fix for refcounting of
of_nodes in the simple-card driver that triggered on a lot of systems
and a fix for topology error handling.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxr49QTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NPqB/9SIiP4GQp+PXfS3PawsSZn1klskmq4
QPUxXCq05MOnn1v/EaK1JoSVWPbOQ7IEcsjucuvTkikGQ9RdWdRKre0auWXVKdpk
dl9D5zHgoAqlQ0RjJN5vn3zNA49/wyZni2MqHytlDvVQOQbI7KZ0aSCGj1RlW0ps
k9sJCfQGmWH0f8WKnutvGBuDbu6rDyD6l+coSdjIxfTbVR6RPNWYa3ttC/ouW1XE
fsjDKRCe3OYf8/goRSpM26CWinCQMdN18OkFkBVcWEyxg8LCvQe0f8aygLMJOZQr
dY3XP5Fz3dYD2oJU5kGUBLbLhjk2/NRejhYI7VhXaKey2x6On0x4N2wH
=u/xe
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.0
A few small fixes, a driver fix for Samsung, a fix for refcounting of
of_nodes in the simple-card driver that triggered on a lot of systems
and a fix for topology error handling.
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
commit da215354eb ("ASoC: simple-card: merge simple-scu-card")
merged simple-card and simple-scu-card. Then it had refcount
underflow bug. This patch fixup it.
We will get below error without this patch.
OF: ERROR: Bad of_node_put() on /sound
CPU: 3 PID: 237 Comm: kworker/3:1 Not tainted 5.0.0-rc6+ #1514
Hardware name: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+ (DT)
Workqueue: events deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x24/0x30
dump_stack+0xb0/0xec
of_node_release+0xd0/0xd8
kobject_put+0x74/0xe8
of_node_put+0x24/0x30
__of_get_next_child+0x50/0x70
of_get_next_child+0x40/0x68
asoc_simple_card_probe+0x604/0x730
platform_drv_probe+0x58/0xa8
...
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_get_child_by_name() takes a reference we'll need to drop
later so when we substitute in top we need to take a reference
as well as just assigning.
Without this patch we hit the following error:
[ 1.246852] OF: ERROR: Bad of_node_put() on /sound-wm8524
[ 1.262261] Hardware name: NXP i.MX8MQ EVK (DT)
[ 1.266807] Workqueue: events deferred_probe_work_func
[ 1.271950] Call trace:
[ 1.274406] dump_backtrace+0x0/0x158
[ 1.278074] show_stack+0x14/0x20
[ 1.281396] dump_stack+0xa8/0xcc
[ 1.284717] of_node_release+0xb0/0xc8
[ 1.288474] kobject_put+0x74/0xf0
[ 1.291879] of_node_put+0x14/0x28
[ 1.295286] __of_get_next_child+0x44/0x70
[ 1.299387] of_get_next_child+0x3c/0x60
[ 1.303315] simple_for_each_link+0x1dc/0x230
[ 1.307676] simple_probe+0x80/0x540
[ 1.311256] platform_drv_probe+0x50/0xa0
This patch is based on an earlier version posted by Kuninori Morimoto
and commit message includes explanations from Mark Brown.
https://patchwork.kernel.org/patch/10814255/
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when playing sound with different sample rates actual
sample rate will be determined by audio stream which starts first
on either primary or secondary PCM. The audio root clock will be
configured appropriately only for the first stream. As the hardware
is limited to same sample rate on both interfaces we need to disallow
streams with different sample rates. It is done by this patch by
returning error in FE hw_params if there is already active stream
running with different sample rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
sound/soc/stm/stm32_sai_sub.c: In function 'stm32_sai_configure_clock':
sound/soc/stm/stm32_sai_sub.c:902:11: warning:
variable 'mask' set but not used [-Wunused-but-set-variable]
sound/soc/stm/stm32_sai_sub.c:902:6: warning:
variable 'cr1' set but not used [-Wunused-but-set-variable]
It's not used any more after 8307b2afd3 ("ASoC: stm32: sai: set sai as
mclk clock provider")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology resources are no longer needed if any element failed to load.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/cs35l36.c:135:20: warning:
symbol 'cs35l36_reg' was not declared. Should it be static?
sound/soc/codecs/cs35l36.c:248:6: warning:
symbol 'cs35l36_readable_reg' was not declared. Should it be static?
sound/soc/codecs/cs35l36.c:398:6: warning:
symbol 'cs35l36_precious_reg' was not declared. Should it be static?
sound/soc/codecs/cs35l36.c:410:6: warning:
symbol 'cs35l36_volatile_reg' was not declared. Should it be static?
Fixes: 6ba9dd6c89 ("ASoC: cs35l36: Add support for Cirrus CS35L36 Amplifier")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sdm845 uses dmic on EC so it should select CROS_EC_CODEC.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to RM SPDIF STC SYSCLK_DF field is 9-bit wide, values
being in 0..511 range. Use a proper type to handle sysclk_df.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The on-chip PLL can be disabled if on the MCLKI pin we have an external
clock at 512 x fs. This clock can be used as direct internal clock for
ADCs or DACs.
To support this, we add an extra clock id that can be configured
using the set_sysclk() callback.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver only supports DPS_A for DAC, which is configured at probe.
This patch adds support for DSP_A and I2S modes by using the set_fmt()
callback.
A trivial break is also removed from a case's default branch.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, the codec starts to interpret the left (first) channel on
the falling edge (low polarity) of LRCLK. However, for DSP_A, the left
channel needs to start on the rising edge of LRCLK. This patch fixes
this channel swap by toggling the bit which selects the LRCLK polarity.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DACs and ADCs on ad193x codecs require a 32 bit slot size. We should
assure that no other size is used.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some ad193x codecs don't have ADCs, so they have no capture capabilities.
This way, we can use this driver in multicodec cards.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At least some USB devices use (MSB-aligned) audio format larger
than the actual resolution of the device. In order to expose the
actual device resolution (bBitResolution), add extra field to the
procfs stream info interface.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When np is NULL i2s_pdata could also be NULL but i2s_pdata is now being
dereferenced without proper check. Fix this and shorten the error message
so we don't exceed 80 characters limit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is now no users of this flag so remove it together with
related code. The chan_name field of snd_dmaengine_dai_dma_data
data structure is not removed as it is still in use by the PXA
platform.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous implementatation was restrictive with regards to
BCLK rates for slave mode where the driver would not allow rates
the codec couldn't provide itself as clock master. The codec
is able to automatically determine and handle whatever rate is
provided so this restriction isn't necessary for slave mode. The
code was also flawed with regards to setting of the frame offset
as using rx_mask to explicitly set the offset has the knock on
effect of impacting the min and max channels for the codec, in
soc_pcm_hw_params() through the call to
soc_pcm_codec_params_fixup().
With this update, the driver now only limits frame size if codec
is clock master, and dynamically determines the BCLK offset
relating to WCLK using the tx_mask for slot offset along with the
slot width provided.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously the driver would default the BCLK periods per WCLK to
64, to cover all possible non-TDM scenarios when the codec was
DAI clock master. However some devices require a lower BCLK rate
to operate correctly so with this in mind, this commit updates
the code to be more dynamic, with BCLK rate now based on SR and
word length provided to hw_params().
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Spelling error fixes, upper/lower case letter changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change indentation so this macro definition spans 2 rows and looks
more consistent with surrounding code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the probe call is on the primary DAI we can use 'other' in place of
i2s->sec_dai, if the probe call is on the secondary DAI we can use 'i2s'
in place of other->sec_dai.
While at it fix one whitespace issue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Fixes: 7dd0d83558 ("ASoC: stm32: sai: simplify sync modes management")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Acked-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a part of conversion of Samsung platforms to use the custom DMA
config for specifying DMA channel names, in addition to passing custom
DMA device for the secondary CPU DAI's "PCM" component for some variants
of the I2S controller.
We also don't set the SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME any more
as setting it wouldn't allow to specify DMA channels through the custom
DMA config.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DPCM links in order to support the secondary I2S interface.
For the secondary PCM interface to be actually available one more entry
should be added to the sound-dai property in sound/cpu node in DT.
The changes in driver are done in a way so we are backwards compatible
with existing DTS/DTB, i.e. if the cpu sound-dai property contains only
one entry only one PCM will be registered.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch makes the spinlock serializing access to the primary/secondary
PCM a per I2S controller lock, rather than a global one. There is no need
to have a global lock across multiple I2S controllers in the SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirk flags are common for the primary and the secondary DAI
so move respective field from struct i2s_dai to common driver data
structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IP variant data is another thing common for both DAIs, move it
to the driver's common data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we now have the 'priv' pointer in most of the places we can use
priv->lock directly, dropping extra indirection in the SFR region
spinlock access.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SFR region is common for both DAIs so move related data structure
field from struct i2s_dai to the common driver data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
sound/isa/es1688/es1688_lib.c: In function 'snd_es1688_probe':
sound/isa/es1688/es1688_lib.c:124:31: warning:
variable 'hw' set but not used [-Wunused-but-set-variable]
unsigned short major, minor, hw;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is reported that there's a constant background "hum/whitenoise"
in the headset on the Lenovo X1 machines with the codec alc285, and it
is confirmed that if we run the command below, the noise will stop.
sudo hda-verb /dev/snd/hwC0D0 0x1d SET_PIN_WIDGET_CONTROL 0x0
Then I consulted this issue with Kailang, he told me the pin 0x1d on
this codec is used for PC beep in, the noise probably comes from this
pin and we can also disable the PC beep in passthrough, then the PC
beep in will not affect other sound playback.
Fixes: c4cfcf6f42 ("ALSA: hda/realtek - fix the pop noise on headphone for lenovo laptops")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1660581
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the System76 Oryx Pro (oryp5), there is a headset microphone input
attached to 0x19 that does not have a jack detect. In order to get it
working, the pin configuration needs to be set correctly, and the
ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied. This is
similar to the MIC_NO_PRESENCE fixups for some Dell laptops, except we
have a separate microphone jack that is already configured correctly.
Since the ALC1220 does not have a fixup similar to
ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC, I have exposed the fixup from the
ALC269 in a way that it can be accessed from the
alc1220_fixup_system76_oryp5 function. In addition, the
alc1220_fixup_clevo_p950 needs to be applied to gain speaker output.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the following sparse warning:
sound/soc/codecs/cros_ec_codec.c:209:27: warning:
symbol 'cros_ec_dai' was not declared. Should it be static?
Fixes: b291f42a37 ("ASoC: cros_ec_codec: Add codec driver for Cros EC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/mediatek/mt8183/mt8183-dai-i2s.c:966:5: warning:
symbol 'mt8183_dai_i2s_get_share' was not declared. Should it be static?
sound/soc/mediatek/mt8183/mt8183-dai-i2s.c:986:5: warning:
symbol 'mt8183_dai_i2s_set_priv' was not declared. Should it be static?
Fixes: a94aec035a ("ASoC: mediatek: mt8183: add platform driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to keep the PM suspend/resume register cache separate
for each DAI as those registers are common, move related i2s_dai data
structure to the driver's common data structure. This will allow us
to simplify the code a little eventually and to make it easier to follow.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock for generating I2S signals is also common for both CPU DAIs
so move it to the driver's common data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core clock is also common for both CPU DAIs so move it to
the driver's private data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DAPM widgets required to model the internal mixer
of the I2S controller merging audio streams from the primary and
from the secondary PCM interface.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having the clocks provider data in struct samsung_i2s_priv, i.e. per the I2S
controller instance, rather than per CPU DAI better models the hardware and
simplifies the code a little. The clock provider is common for both DAIs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces again registration of additional platform device as
we still need it for registering the secondary dmaengine PCM component.
This patch in most part is a revert of changes done in commit
be2c92eb64 ("ASoC: samsung: i2s: Remove virtual device for secondary DAI")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This avoids bringing back the problem introduced by
62ba568f7a ("ALSA: pcm: Return 0 when size <
start_threshold in capture") and fixed in 00a399cad1
("ALSA: pcm: Revert capture stream behavior change in
blocking mode"), which prevented the user from starting
capture from another thread.
Signed-off-by: Ricardo Biehl Pasquali <pasqualirb@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a bit of surprising that we've got more changes than hoped
at this late stage, but the all don't look too scaring but small
fixes.
One change in ALSA core side is again the PCM regression fix that
was partially addressed for OSS, but now the all relevant change
is reverted instead. Also, a few ASoC core fixes for UAF and OOB
are included, while the rest are usual random device-specific
fixes.
-----BEGIN PGP SIGNATURE-----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=NQQX
-----END PGP SIGNATURE-----
Merge tag 'sound-5.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It's a bit of surprising that we've got more changes than hoped at
this late stage, but they all don't look too scary but small fixes.
One change in ALSA core side is again the PCM regression fix that was
partially addressed for OSS, but now the all relevant change is
reverted instead. Also, a few ASoC core fixes for UAF and OOB are
included, while the rest are usual random device-specific fixes"
* tag 'sound-5.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Revert capture stream behavior change in blocking mode
ALSA: usb-audio: Fix implicit fb endpoint setup by quirk
ALSA: hda - Add quirk for HP EliteBook 840 G5
ASoC: samsung: Prevent clk_get_rate() calls in atomic context
ASoC: rsnd: ssiu: correct shift bit for ssiu9
ASoC: rsnd: fixup rsnd_ssi_master_clk_start() user count check
ASoC: dapm: fix out-of-bounds accesses to DAPM lookup tables
ASoC: topology: fix oops/use-after-free case with dai driver
ASoC: rsnd: fixup MIX kctrl registration
ASoC: core: Allow soc_find_component lookups to match parent of_node
ASoC: rt5682: Correct the setting while select ASRC clk for AD/DA filter
ASoC: MAINTAINERS: fsl: Change Fabio's email address
ASoC: hdmi-codec: fix oops on re-probe
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch includes minimal changes as a prerequisite for adding support
for the Exynos secondary I2S interface as second DAI of the I2S component.
Doing it that way allows to avoid problems as indicated in commmit
6b01e0365b1689 ("ASoC: samsung: i2s: disable secondary DAI until it gets fixed")
The samsung_i2s_get_pri_dai() helper added in this patch is temporary and
will be removed in one of subsequent patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The additional function argument will allow to select proper DMA device
for requesting DMA channel for the secondary CPU DAI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are currently two ways to specify custom DMA channel names:
- through the SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME flag and
snd_dmaengine_dai_dma_data data structure,
- through chan_names field of struct snd_dmaengine_pcm_config.
In order to replace the DAI DMA data method with the custom DMA config
one on non-DT platforms the dmaengine_pcm_new() function is extended
to also consider channel names specified in the custom DMA config.
If both config->chan_names and dma_data->chan_name are provided
the former will be used.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when of_node of the "PCM" device is null
dmaengine_pcm_request_chan_of() function will bail out, including cases
when custom DMA device is intended to be used. To have the channels
properly requested when custom DMA device is provided extend the of_node
test to also consider dma_dev->of_node.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure i2s->rclk_srcrate is properly initialized also during
playback through the secondary DAI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Silence warnings (triggered at W=1) by adding relevant __printf
attributes.
sound/soc/soc-dapm.c:149:2: warning: function 'pop_dbg' might be a candidate for 'gnu_printf' format attribute [-Wsuggest-attribute=format]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As stated in 'TLV320AIC3254 Application Reference Guide' ([1]):
3.2 Device Startup Lockout Times
After the TLV320AIC3254 initializes through hardware reset at power-up
or software reset, the internal registers initialize to default values.
This initialization takes place within 1ms after pulling the RESET
signal high. During this initialization phase, no register-read or
register-write operation should be performed on ADC or DAC coefficient
buffers. Also, no block within the codec should be powered up during
the initialization phase.
[1] http://www.ti.com/lit/an/slaa408a/slaa408a.pdf
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
For correct operation of the digital filtering and other processing on the
WM8741, the user must ensure the correct value of OSR[1:0] is set at all
times.[1] Hence, depending the selected sampling rate, set the OSR (over-
sampling rate) mode in hw_params().
References:
[1] "WM8741 Data Sheet"
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BE dai links only have internal PCM's and their substream ops may
not be set. Suspending these PCM's will result in their
ops->trigger() being invoked and cause a kernel oops.
So skip suspending PCM's if their ops are NULL.
[ NOTE: this change is required now for following the recent PCM core
change to get rid of snd_pcm_suspend() call. Since DPCM BE takes
the runtime carried from FE while keeping NULL ops, it can hit this
bug. See details at:
https://github.com/thesofproject/linux/pull/582
-- tiwai ]
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Loading/unloading modules exposes issues with memory allocation, which
is a mix of devm_kzalloc and manual kzalloc. Move to devm_k routines
everywhere to simplify all this.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADC and DAC can be clocked from separate or same sources CLK1 and CLK2.
By default, ADC is clocked from CLK1, and DAC - from CLK2.
This commits allows sound cards to selest a proper clock source during
`hw_params()` via `snd_soc_dai_set_sysclk()`. It makes possible to have a
single clock source for both ADC and DAC.
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
Softly reset registers values on module probe
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no risk of the module being removed while the platform
components are in use. This solves the problem of the snd_soc_skl
module not being removable with rmmod
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core has for the longest time increased the module reference
counts, even before the transition to the component model. This is
probably fine on most platforms, but it introduces a deadlock case on
Intel devices with the Skylake and SOF drivers which cannot be removed
due to their reference counts being modified by the core.
In these 2 cases, the PCI or ACPI driver .probe creates a platform
device to let the machine driver .probe register the audio
card. Conversely the PCI or ACPI driver .remove will unregister the
platform device which results in the card being removed by the machine
driver .remove.
With ascii art, this can be represented as
modprobe
snd_soc_skl/
soc-pci-dev/sof-acpci-dev ----------> pci/acpi probe
^ |
| ---------------|
| | |
| V V
increase register register machine
refcount component platform_device
^ |
| |
| V
component <---- register card <---- probe
probe
The issue is that by playing with the component's module reference
counts during the card registration, it's no longer possible to remove
the module which controls the component. This can be shown, e.g. with
the following error:
root@plb-XPS-13-9350:~# lsmod | grep snd_soc_skl
snd_soc_skl 110592 1
root@plb-XPS-13-9350:~# rmmod snd_soc_skl
rmmod: ERROR: Module snd_soc_skl is in use
Increasing the reference count during the component probe is not
useful. If the PCI/ACPI module is removed, the card will be removed
anyway.
To avoid breaking existing platforms and allowing Intel platforms to
safely deal with module load/unload cases, this patch introduces a
flag which needs to be set during the component initialization. This
is a strictly opt-in capability that should only be used when the
handling of the component module does not require a reference count
increase to prevent removal during use.
Note that this solution is not directly applicable to the legacy
Atom/SST driver, which uses a different device hierarchy. There are
however additional refcount issues which prevent the ACPI driver from
being removed. This is a different issue which would need a different
patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
New quirk enforces search for GPIO based on its type,
i.e. iterate over GpioIo resources only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing license and copyright information which never made it
into the analog driver when the original driver was split in two as part
of the review process.
Link: https://lkml.kernel.org/r/1465582725-30183-3-git-send-email-srinivas.kandagatla@linaro.org
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator notifiers, that were registered during codec driver probing,
must be unregistered during driver release, or device managed versions
have to be used. This patch fixes codec drivers, that weren't explicitly
unregistering notifiers and simplifies those, that did that manually.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we need multiple components for I915 for different purposes
(Audio & Mei_hdcp), we adopt the subcomponents methodology introduced
by the previous patch (mentioned below).
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jan 28 17:08:20 2019 +0530
components: multiple components for a device
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by-by: Ramalingam C <ramalinagm.c@intel.com> (commit message)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (code)
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Russell King <rmk+kernel@arm.linux.org.uk>
cc: Rafael J. Wysocki <rafael@kernel.org>
cc: Jaroslav Kysela <perex@perex.cz>
cc: Takashi Iwai <tiwai@suse.com>
cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207232759.14553-4-daniel.vetter@ffwll.ch
In the commit 62ba568f7a ("ALSA: pcm: Return 0 when size <
start_threshold in capture"), we changed the behavior of
__snd_pcm_lib_xfer() to return immediately with 0 when a capture
stream has a high start_threshold. This was intended to be a
correction of the behavior consistency and looked harmless, but this
was the culprit of the recent breakage reported by syzkaller, which
was fixed by the commit e190161f96 ("ALSA: pcm: Fix tight loop of
OSS capture stream").
At the time for the OSS fix, I didn't touch the behavior for ALSA
native API, as assuming that this behavior actually is good. But this
turned out to be also broken actually for a similar deployment,
e.g. one thread goes to a write loop in blocking mode while another
thread controls the start/stop of the stream manually.
Overall, the original commit is harmful, and it brings less merit to
keep that behavior. Let's revert it.
Fixes: 62ba568f7a ("ALSA: pcm: Return 0 when size < start_threshold in capture")
Fixes: e190161f96 ("ALSA: pcm: Fix tight loop of OSS capture stream")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now all callers no longer check the return value from
snd_pcm_lib_preallocate_pages() and co, let's make them to return
void, so that any new code won't fall into the same pitfall.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
