The patch adds support for detecting the P2P (peer-to-peer) event packets.
This is required for timestamping the PTP packets in peer delay mode.
Unmask the below bits (set to 0) for device to detect the p2p packets.
NIG_REG_P0/1_LLH_PTP_PARAM_MASK
NIG_REG_P0/1_TLLH_PTP_PARAM_MASK
bit 1 - IPv4 DA 1 of 224.0.0.107.
bit 3 - IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
NIG_REG_P0/1_LLH_PTP_RULE_MASK
NIG_REG_P0/1_TLLH_PTP_RULE_MASK
bit 2 - {IPv4 DA 1; UDP DP 0}
bit 6 - MAC Ethertype 0 of 0x88F7.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: fa7e28127a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove implementation of get_port_parent_id ndo and rely on core calling
into devlink for the information directly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the switch_id is being only initialized when switching eswitch
mode from "legacy" to "switchdev". However, nothing prevents the id to
be initialized from the very beginning. Physical ports can show it even
in "legacy" mode.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make tg3 behave like other drivers and let "ethtool -p" identify the
NIC even when it's in the DOWN state. Before this patch it would get an
error as follows if the NIC was down:
# ip link set down dev em4
# ethtool -p em4
Cannot identify NIC: Resource temporarily unavailable
With this patch ethtool identify works regardless of whether the NIC is up
or down as it does for other drivers.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for this.
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rely on the previously introduced fallback and let the core
call devlink in order to get the physical port name.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for devlink compat functions to work, implement
ndo_get_devlink_port. Legacy slaves does not have devlink port instances
created for themselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8fcf0ec44c11f "bnx2x: Add FW 7.13.11.0" added said .bin FW to
linux-firmware; This patch incorporates the FW in the bnx2x driver.
This introduces few FW fixes and the support for Tx VLAN filtering.
Please consider applying it to 'net-next' tree.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the type set of devlink port after it is registered.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink_port_type_eth_set() before devlink_port_register(). Bnxt
instances won't change type during lifetime. This avoids one extra
userspace devlink notification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the attrs properly so delink has enough info to generate physical
port names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink functions are in use, so include the related header file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, especially given we use a dev_info() which
already displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been a slightly more active cycle than normal with ongoing core
changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5 On-Demand-Paging MR
feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and fixing
the various unregistration race conditions in rxe's unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
* Drivers should not assume umem SGLs are in PAGE_SIZE chunks
* ucontext is accessed via udata not other means
* Start to make the core code responsible for object memory
allocation
* Drivers should convert struct device to struct ib_device
via a helper
* Drivers have more tools to avoid use after unregister problems
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEfB7FMLh+8QxL+6i3OG33FX4gmxoFAlyAJYYACgkQOG33FX4g
mxrWwQ/+OyAx4Moru7Aix0C6GWxTJp/wKgw21CS3reZxgLai6x81xNYG/s2wCNjo
IccObVd7mvzyqPdxOeyHBsJBbQDqWvoD6O2duH8cqGMgBRgh3CSdUep2zLvPpSAx
2W1SvWYCLDnCuarboFrCA8c4AN3eCZiqD7z9lHyFQGjy3nTUWzk1uBaOP46uaiMv
w89N8EMdXJ/iY6ONzihvE05NEYbMA8fuvosKLLNdghRiHIjbMQU8SneY23pvyPDd
ZziPu9NcO3Hw9OVbkwtJp47U3KCBgvKHmnixyZKkikjiD+HVoABw2IMwcYwyBZwP
Bic/ddONJUvAxMHpKRnQaW7znAiHARk21nDG28UAI7FWXH/wMXgicMp6LRcNKqKF
vqXdxHTKJb0QUR4xrYI+eA8ihstss7UUpgSgByuANJ0X729xHiJtlEvPb1DPo1Dz
9CB4OHOVRl5O8sA5Jc6PSusZiKEpvWoyWbdmw0IiwDF5pe922VLl5Nv88ta+sJ38
v2Ll5AgYcluk7F3599Uh9D7gwp5hxW2Ph3bNYyg2j3HP4/dKsL9XvIJPXqEthgCr
3KQS9rOZfI/7URieT+H+Mlf+OWZhXsZilJG7No0fYgIVjgJ00h3SF1/299YIq6Qp
9W7ZXBfVSwLYA2AEVSvGFeZPUxgBwHrSZ62wya4uFeB1jyoodPk=
=p12E
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a slightly more active cycle than normal with ongoing
core changes and quite a lot of collected driver updates.
- Various driver fixes for bnxt_re, cxgb4, hns, mlx5, pvrdma, rxe
- A new data transfer mode for HFI1 giving higher performance
- Significant functional and bug fix update to the mlx5
On-Demand-Paging MR feature
- A chip hang reset recovery system for hns
- Change mm->pinned_vm to an atomic64
- Update bnxt_re to support a new 57500 chip
- A sane netlink 'rdma link add' method for creating rxe devices and
fixing the various unregistration race conditions in rxe's
unregister flow
- Allow lookup up objects by an ID over netlink
- Various reworking of the core to driver interface:
- drivers should not assume umem SGLs are in PAGE_SIZE chunks
- ucontext is accessed via udata not other means
- start to make the core code responsible for object memory
allocation
- drivers should convert struct device to struct ib_device via a
helper
- drivers have more tools to avoid use after unregister problems"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (280 commits)
net/mlx5: ODP support for XRC transport is not enabled by default in FW
IB/hfi1: Close race condition on user context disable and close
RDMA/umem: Revert broken 'off by one' fix
RDMA/umem: minor bug fix in error handling path
RDMA/hns: Use GFP_ATOMIC in hns_roce_v2_modify_qp
cxgb4: kfree mhp after the debug print
IB/rdmavt: Fix concurrency panics in QP post_send and modify to error
IB/rdmavt: Fix loopback send with invalidate ordering
IB/iser: Fix dma_nents type definition
IB/mlx5: Set correct write permissions for implicit ODP MR
bnxt_re: Clean cq for kernel consumers only
RDMA/uverbs: Don't do double free of allocated PD
RDMA: Handle ucontext allocations by IB/core
RDMA/core: Fix a WARN() message
bnxt_re: fix the regression due to changes in alloc_pbl
IB/mlx4: Increase the timeout for CM cache
IB/core: Abort page fault handler silently during owning process exit
IB/mlx5: Validate correct PD before prefetch MR
IB/mlx5: Protect against prefetch of invalid MR
RDMA/uverbs: Store PR pointer before it is overwritten
...
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being able to build devlink as a module causes growing pains.
First all drivers had to add a meta dependency to make sure
they are not built in when devlink is built as a module. Now
we are struggling to invoke ethtool compat code reliably.
Make devlink code built-in, users can still not build it at
all but the dynamically loadable module option is removed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver returns -ENOSPC when tc_can_offload() check fails. Since that
routine checks for flow parameters that are not supported by the driver,
we should return the more appropriate -EOPNOTSUPP.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SIOCGMIIREG and SIOCSMIIREG ioctls to
mdio read/write to external PHY.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware. Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for BCM957504 with device ID 1751
Signed-off-by: Erik Burrows <erik.burrows@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c: In function 'bnx2x_get_hwinfo':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:11940:10: warning:
variable 'mfw_vn' set but not used [-Wunused-but-set-variable]
It's never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT has its RXCHK parser block that attempts to validate the
packet structures, unfortunately setting the L2 header check bit will
cause Bridge PDUs (BPDUs) to be incorrectly rejected because they look
like LLC/SNAP packets with a non-IPv4 or non-IPv6 Ethernet Type.
Fixes: 4e8aedfe78c7 ("net: systemport: Turn on offloads by default")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b639583f9e.
As per discussion with Jakub Kicinski and Michal Kubecek,
this will be better addressed by soon-too-come ethtool netlink
API with additional indication that given configuration request
is supposed to be persisted.
Also, remove the parameter support from bnxt_en driver.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Michal Kubecek <mkubecek@suse.cz>
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable fsz is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user can do dump or get of param values right after the
devlink params are registered. However the driver may not be initialized
which is an issue. The same problem happens during notification
upon param registration. Allow driver to publish devlink params
whenever it is ready to handle get() ops. Note that this cannot
be resolved by init reordering, as the "driverinit" params have
to be available before the driver is initialized (it needs the param
values there).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enabling RDMA driver support on 57500 chips. Removing the forced error
code for 57500 chip.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
dev_consume_skb_irq() should be called in sbdma_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
BNXT only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get(). The conversion is
straight forward here since the PF and VF code use the same getter.
Since bnxt makes uses of switchdev_port_same_parent_id() convert it to
use netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates drivers to use the new flow action infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.
To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.
This introduces two new interfaces:
bool flow_rule_match_key(rule, dissector_id)
that returns true if a given matching key is set on, and:
flow_rule_match_XYZ(rule, &match);
To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
