Like other switches, the Aten CS-1758 KVM switch needs a quirk to avoid
spewing errors:
[12599018.071059] usb 5-2: input irq status -75 received
[12599018.079053] usb 5-2: input irq status -75 received
Signed-off-by: Vasilis Liaskovitis <vliaskovitis@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.
Commit 60a2218698 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).
This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.
Cc: stable@vger.kernel.org
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.
This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool. To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.
It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These two functions awkwardly break up the otherwise-contiguous chunk of
related Intuos IRQ functions with a 500 line tangent about the operation
of the EKR. Their presence makes it difficult to read/navigate through the
the Intuos code. Since there is no dependency between these functions, it
is possible to simply move them down somewhat. This commit moves them
to be after the final Intuos IRQ function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commits d793ff8 and 4082da8 introduced two pad usages which do not
actually send pad input events. To make sure we do not post empty
pad packets, pad_input_event_flag is introduced. Turn on the flag
for real pad input events so we can synchronize them properly.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device has a different vendor id but responds to initialization.
Signed-off-by: Xiaolei Yu <dreifachstein@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
err is being checked for failure each time it is being updated
so this err check is totally redundant and can be removed
Detected with CoverityScan, CID#1420665 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure we sure register any sensor when sony_input_configured failes.
Somehow this line got lost during resolving of merge conflicts in the
motion sensor patch series and a redudant remove was added as well later
on.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default when using bluetooth the DS4 reports data at about 1kHz,
which is quite fast especially on weak devices. We now make the
device use the USB poll interval, which is a fixed 4ms. In addition
we make the value adjustable through sysfs.
The error handling in sony_input_configured is a little tricky. It
is not easy to add other goto's as not all codepaths have logic
for adding this attribute. Luckily we are setting the value for the
attribute to a default value, so we can use that to detect if we need
to remove the file.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only set bit flags for the portions of the DS4 output report
for which we have data.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These colors are more the default colors normally used on the DS4.
The previous ones were faint and not so noticeable.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The navigation controller is a DS3 (sixaxis) with fewer physical
axes and buttons. It utilizes the same HID report as the DS3 and
thus reports axes/buttons which aren't physically present.
Currently many non-existing buttons and axes are reported, which
we are now removing.
For the axes/buttons which do exist, we make the axis/button mapping
similar to the DS3.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS3 MAC address is reported as a unique identified when
using Bluetooth. For USB there is no unique identifier reported
yet, so use the MAC address.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This way, upower can add a simple udev rule to decide whether or not
it should use the internal unifying support or just the generic kernel
one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Solar Keyboard uses a different feature to report the battery level.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CAPACITY LEVEL allows to forward rough information on the battery mileage.
HID++ 2.0 devices will either report percentage or levels, so better
forwarding this information to the user space.
The M325 supports only 2 levels: 'Full' and 'Critical'. With mileage,
it will report either 90% or 5%, which might confuse users. With this
change the battery will either report "Full" or "Critical".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply term for the percentage is capacity. Capacity level
can be given when non accurate mileage is provided by the device, so
better stick to the terms used in power_supply.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When ONLINE isn't set, upower should ignore the battery capacity,
so there is no need to overload it with some random values.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a device reconnects, there is a high chance its power supply has
been changed (for a battery replacement for instance). Just forward
the battery state here.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or the device just answers a valid feature '0'.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The creation of the power_supply should not be in a HID++ 2.0 specific
function.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Better forwarding the device name, manufacturer and serial to upower.
Note that serial is still empty, it will be filled in a later patch
in this series.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery events are reported through HID++, so we need to be sure
the report ID is the HID++ one.
Without this, we might receive keyboard events that looks just like
battery events with wrong data and which will confuse user space.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like all users don't care about a disconnect.
Simplify the various variant_connect() and put the connect state check
at the beginning.
For delayed input devices, make sure we go through all other connect
values (protocol, battery) before bailing out.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp->name can't be null.
Only HID++ 2.0 and above device supports the query.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unifying devices are different from others because they can probed
while not connected. So we need to talk to the receiver to get some
extra information like the device name and the serial.
Instead of having conditionals while attempting to read the device name
from HID++ 2.0, have a special init path for them.
Store the retrieved serial in hdev->uniq.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not pollute the quirks bits field which is public API
with elements that are queried from the device.
Move the 2 battery capabilities into the new field.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unless they are connected through unifying, they don't support it,
so remove one error in the logs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without a scope defined, UPower assumes that the battery provides
power to the computer it's connected to, like a laptop battery or a UPS.
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Register 0xB5 should be handled specially no matter what function is
used. This allows to retrieve the serial and the Quad ID from
hid-logitech-hidpp directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 3b164a00a9 ("HID: wacom: Cleanup unsupported device_type
for BAMBOO_PT") cleaned up Bamboo devices which our driver falsely
claimed had touch. Bamboo One Medium also does not have touch.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a544c619a5 ("HID: wacom: do not attempt to switch mode
while in probe") introduces delayed work for querying (setting the
mode) on all tablets. Bamboo Touch (056a:00d0) has a ghost
interface which claims to be a pen device. Though this device can
be removed, we have to set the mode on the ghost pen interface
before we remove it. After the aforementioned delay was introduced
the device was being removed before the mode setting could be
executed.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A previous commit (below) adds a check for already probed interfaces to
Wacom's matching heuristic. Unfortunately this causes the Bamboo Pen
(CTL-460) to match itself to its 'ghost' touch interface. After
subsequent changes to the driver this match to the ghost causes the
kernel to crash. This patch avoids calling wacom_add_shared_data()
for the BAMBOO_PEN's ghost touch interface.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
They are part of HUTRR34 for multi-touch digitizers:
0x0E Device configuration CA 16.7
0x23 Device settings CL 16.7
Signed-off-by: Xiaolei Yu <dreifachstein@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a new clone of the XIN MO arcade controller which has same issue with
out of range like the original. This fix will solve the issue where 2
directions on the joystick are not recognized by the new THT 2P arcade
controller with device ID 0x75e1. In details the new device ID is added the
hid-id list and the hid-xinmo source code.
Signed-off-by: Peter Stein <peter@stuntstein.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
GPIOLIB_IRQCHIP is not visible to user, so we can't depend on it.
Depend on GPIOLIB but select GPIOLIB_IRQCHIP.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to store the minor number each drivers. In case of hidraw, the
minor number is stored stores in struct hidraw. But hiddev's minor is
located in struct hid_device.
The hid-core driver announces a kernel message which driver is loaded when
HID device connected, but hiddev's minor number is always zero. To proper
display hiddev's minor number, we need to store the minor number asked from
usb core and do some refactoring work (move from hiddev.c to hiddev.h) to
access hiddev in hid-core.
[jkosina@suse.cz: rebase on top of newer codebase]
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The cp2112 driver is working on hidraw not hiddev. So we need to use proper
hidraw name with hidraw's minor number.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Game controllers can be connected twice through USB and BT. Only
one connection is allowed. Currently we perform a check for duplicate
controllers halfway through device initialization. To prevent
'transient' devices, we should do this check as early as we can.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a separate evdev node for the DS3 its motion
sensors. We only expose the accelerometers as the gyroscope
is extremely difficult to manage and behavior varies a lot
between hardware revisions.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds printing when we failed to activate DS3 / Nagivation
controllers and checks the return value for these failures earlier
in sony_input_configured. This paves the way for other configuration
logic for these devices, which we don't want to call if for example
the activation failed.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The axis and button mapping for the DS3 is strange. This is mostly
due to the device reporting many axes as for every digital button
it also has an analog button. Due to amount of analog values it
is even leaking well into the MT axes range.
We felt it is best to remove the many analog buttons and just report
digital and comply to the Linux gamepad spec. The analog buttons are
rarely used on the official platform, let alone on Linux.
This patch does remove motion sensor support (added back in another
patch).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the DS4 touchpad device is neither classified as a direct
input device nor as a pointer device. It makes most sense to mark
it as a pointer device.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DualShock 4 dongle isn't connected to a real DualShock 4 at
time of driver loading. When a DualShock 4 is plugged in, we
need to obtain calibration data (the dongle would have zeros).
This patch adds calibration logic, which we schedule on a hotplug
from sony_raw_event. In addition this patch adds dongle state
handling.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver currently uses sony_schedule_work to submit output
reports for the different devices for LEDs or rumble.
This patch adds a new parameter to sony_schedule_work to allow
scheduling for other types of work. The next patch in this series
will utilize this functionality. Considering the driver structure
and all error handling it felt best to reuse sony_schedule_work
and sony_cancel_work. The idea was inspired by the wacom driver
which does something similar.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
