Added get_rxfh_indir_size, get_rxfh_key_size and get_rxfh ethtool_ops
callbacks implementations.
This enables the ethtool's "-x" and "--show-rxfh[-indir]" options.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a preparation for enablement of ethtool RSS indirection
table and hash key querying. We don't want to read registers every time
the RSS info is queried. Therefore we will store its current content in the
arrays in the adapter struct and will read it from there (instead of from
registers) when requested.
Will change the code that writes the indirection table and hash key into
the HW registers to take its content from these arrays. This will also
simplify the indirection table updating ethtool callback implementation
in the future.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-04-10
This series contains updates to ixgbe and documentation for igb,
ixgbe and ixgb.
Stephen cleans up documentation to igb, ixgbe and ixgb.
Don updates how bridge mode is stored to minimize obfuscation and
makes updates for future silicon easier. Adds a new bridge mode
support function which gathers all the logic needed to configure
bridge modes. Adds Source Address Prunning for VEPA bridge mode
for x550 devices.
Vasu adds specific FCoE offloads for x550 for DDP context programming
and increased DDP exchanges.
Alex Duyck cleans up the use of HW_VLAN_CTAG_FILTER in hw_features,
where the driver was actually ignoring the value of the bit and was
just assuming it was always set. Also cleans up the use of rcu_barrier()
since the driver has not used call_rcu() to free the rings for some
time now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe driver hasn't used call_rcu to free the rings for some time now.
Since that is the case the call to rcu_barrier can be dropped since calls
to kfree_rcu don't require it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the HW_VLAN_CTAG_FILTER bit is not falsely
advertised as being a feature that can be toggled on ixgbe parts. The
driver was setting the bit in features and letting it be inherited by
hw_features, however the driver was actually ignoring the value of the bit
and just assuming it was always set. As a result VLAN filtering was always
enabled which is a requirement for SR-IOV, VMDq, DCB, FCoE, and possibly
other features within the adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds x550 specific FCoE offloads for DDP context programming and
increased DDP exchanges.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch will enable X550 Source Address Prunning for VEPA
bridge mode. This requires that we also have replication enabled
as well, while in this mode.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch gathers together all the logic needed to configure bridge
modes. Currently that it is rather simple but this is really laying
the ground work for future X550 feature enhancement.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move documentation into this century, even if this device hasn't
been available for some time.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MTU values in the documentation do not match the source.
The source has frame limit of IXGBE_MAX_JUMBO_FRAME_SIZE (9728)
which is MTU of 9710 because of the accounting for Ethernet header
and CRC.
Also, don't refer to the obsolete ifconfig command.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ifconfig command is obsolete, best to remove all references so that
new users learn ip.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-04-09
We've had enough new patches during the past week (especially from
Marcel) that it'd be good to still get these queued for 4.1.
The majority of the changes are from Marcel with lots of cleanup &
refactoring patches for the HCI UART driver. Marcel also split out some
Broadcom & Intel vendor specific functionality into two new btintel &
btbcm modules.
In addition to the HCI driver changes there's the completion of our
local OOB data interface for pairing, added support for requesting
remote LE features when connecting, as well as a couple of minor fixes
for mac802154.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lookup key for tcp_md5_do_lookup() has to be taken
from addr_sk, not sk (which can be the listener)
Fixes: fd3a154a00 ("tcp: md5: get rid of tcp_v[46]_reqsk_md5_lookup()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2015-04-09
The following series of patches includes functional updates and changes
to the driver.
- Allow ethtool rx-frames coalescing to be changed while the device is up
- Consolidate initialization routine into the init function
- Add support for the TX watchdog timeout
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to be able to detect a hung Tx task by adding the netdev
ndo_tx_timeout function callback. Do not set the watchdog_timeo value
so as to use the system default time (currently 5 seconds).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a call to configure the Rx mode (promiscuous mode, all
multicast mode, etc.) is made in xgbe_start separate from the xgbe_init
function. This call to set the Rx mode should be part of the xgbe_init
function so that calls to the init function don't have to be preceded
with calls to configure the Rx mode.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the device must be down in order to update the rx-frames
coalescing setting because the interrupt indicator is set in the
descriptor data during initialization. Allow this setting to be changed
while the device is up by moving the interrupt decision into the
descriptor reset function and base the decision off of the supplied
descriptor index value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an FDB entry is added or deleted the information about VLAN
is not passed to listening applications like 'bridge monitor fdb'.
With this patch VLAN ID is passed if it was set in the original
netlink message.
Also remove an unused bdev variable.
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi:
* some more work on LAR
* fixes for UMAC scan
* more work on debugging framework
* more work for 8000 devices
* cleanups and small bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVJli2AAoJEG4XJFUm622bh6YH/1oKWWYkzCmAKVT3T3PKYcz8
wSUDp0iOQD/f8bXG6qm9lKeqzsJvvUSYaIJRH/Vh7g0uBGzZ+0aK+Tle7zdsKe9i
OrI+yK65jBWyNMfVO4yl3/Nb9ER3TneEDyrOPkXGnFJcyVnCugPcPRZVXiLS3scq
fQrzZkEOM6Fl+nqMAXK7R9Vhk+Oz2U4Dm2r/Qq9sncAZwWUPGC60Vxc0iVcBKOhH
bFZlvnO0RGeU2DMC0RuDkDhaWAsoUvkkR/EsNCwk38Hs2AOag3hBr8METaIF4S0R
83ftVvjD8eJ8hDKP0AtQtMjZCjtAz+GR6D+maoUKxFQbMUq0xn7E2MqOOLxDeq0=
=25In
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
iwlwifi:
* some more work on LAR
* fixes for UMAC scan
* more work on debugging framework
* more work for 8000 devices
* cleanups and small bugfixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-04-09
1) Prohibit the use/abuse of the xfrm netlink interface on
32/64 bit compatibility tasks. We need a full compat
layer before we can allow this. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Replace wmb()/rmb() with dma_wmb()/dma_rmb() where appropriate, round 2
More cleanup of drivers in order to start making use of dma_rmb and dma_wmb
calls. This is another pass of what I would consider to be low hanging
fruit. There may be other opportunities to make use of the barriers in the
Mellanox and Chelsio drivers but I didn't want to risk meddling with code I
was not completely familiar with so I am leaving that for future work.
I have revisited the Mellanox driver changes. This time around I went only
for the sections with a clearly defined pattern. For dma_wmb I used it
between accesses of the descriptor bits followed by owner or size. For
dma_rmb I used it to replace rmb following a read of the ownership bit in
the descriptor.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the CPU overhead for transmit and receive by using lightweight dma_
barriers instead of full barriers where they are applicable.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update i40e and i40evf to use dma_rmb. This should improve performance by
decreasing the barrier overhead on strong ordered architectures.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch should help to improve the performance of the mlx4 and mlx5 on a
number of architectures. For example, on x86 the dma_wmb/rmb equates out
to a barrer() call as the architecture is already strong ordered, and on
PowerPC the call works out to a lwsync which is significantly less expensive
than the sync call that was being used for wmb.
I placed the new barriers between any spots that seemed to be trying to
order memory/memory reads or writes, if there are any spots that involved
MMIO I left the existing wmb in place as the new barriers cannot order
transactions between coherent and non-coherent memories.
v2: Reduced the replacments to just the spots where I could clearly
identify the usage pattern.
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Ido Shamay <idos@mellanox.com>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Chelsio Ethernet drivers to use the dma_rmb/wmb calls instead of
the full barriers in order to improve performance.
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink attribute for the power is s8. But for the driver level
operations we are collection power level value into integer.
It has to be change to s8 from int.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel vendors events indicating firmware loading result and the
bootup of the operational firmware are currently hardcoded byte
comparisons. So intead of doing that, provide proper data structures
and actually use them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When establishing a Bluetooth LE connection, read the remote used
features mask to determine which features are supported. This was
not really needed with Bluetooth 4.0, but since Bluetooth 4.1 and
also 4.2 have introduced new optional features, this becomes more
important.
This works the same as with BR/EDR where the connection enters the
BT_CONFIG stage and hci_connect_cfm call is delayed until the remote
features have been retrieved. Only after successfully receiving the
remote features, the connection enters the BT_CONNECTED state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
FastOpen requests are not like other regular request sockets.
They do not yet use rsk_timer : tcp_fastopen_queue_check()
simply manually removes one expired request from fastopenq->rskq_rst
list.
Therefore, tcp_check_req() must not call mod_timer_pending(),
otherwise we crash because rsk_timer was not initialized.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MzOJ
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC: 4.1 pull request
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commits:
d92916f71a ("sfc: Own header for nic-specific sriov functions,")
25672dba95 ("sfc: Enable VF's via a write to the sysfs file
sriov_numvfs")
As they break the build with SRIOV disabled and there is no
easy way to fix it the way things are arranged.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More recent GCC warns about two kinds of switch statement uses:
1) Switching on an enumeration, but not having an explicit case
statement for all members of the enumeration. To show the
compiler this is intentional, we simply add a default case
with nothing more than a break statement.
2) Switching on a boolean value. I think this warning is dumb
but nevertheless you get it wholesale with -Wswitch.
This patch cures all such warnings in netfilter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Nicolas Dichtel says:
====================
selinux: add some missing nlmsg commands
It's not a critical issue, thus the patches are based on net-next.
Patches are splitted because the 'Fixes' tag is not the same for all
commands.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These commands are missing.
Fixes: 28d8909bc7 ("[XFRM]: Export SAD info.")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This command is missing.
Fixes: ecfd6b1837 ("[XFRM]: Export SPD info")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new command is missing.
Fixes: 880a6fab8f ("xfrm: configure policy hash table thresholds by netlink")
Reported-by: Christophe Gouault <christophe.gouault@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new command is missing.
Fixes: 9a9634545c ("netns: notify netns id events")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new commands are missing.
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWMAC block on certain SoCs (such as IMG Pistachio) have a second
clock which must be enabled in order to access the peripheral's
register interface, so add support for requesting and enabling an
optional "pclk".
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 79b16aadea
("udp_tunnel: Pass UDP socket down through udp_tunnel{, 6}_xmit_skb()")
introduce 'sk' but we already have one inner 'sk'.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov says:
====================
hv_netvsc: linearize SKBs bigger than MAX_PAGE_BUFFER_COUNT-2 pages
This patch series fixes the same issue which was fixed in Xen with commit
97a6d1bb2b ("xen-netfront: Fix handling packets on
compound pages with skb_linearize").
It is relatively easy to create a packet which is small in size but occupies
more than 30 (MAX_PAGE_BUFFER_COUNT-2) pages. Here is a kernel-mode reproducer
which tries sending a packet with only 34 bytes of payload (but on 34 pages)
and fails:
static int __init sendfb_init(void)
{
struct socket *sock;
int i, ret;
struct sockaddr_in in4_addr = { 0 };
struct page *pages[17];
unsigned long flags;
ret = sock_create_kern(AF_INET, SOCK_STREAM, IPPROTO_TCP, &sock);
if (ret) {
pr_err("failed to create socket: %d!\n", ret);
return ret;
}
in4_addr.sin_family = AF_INET;
/* www.google.com, 74.125.133.99 */
in4_addr.sin_addr.s_addr = cpu_to_be32(0x4a7d8563);
in4_addr.sin_port = cpu_to_be16(80);
ret = sock->ops->connect(sock, (struct sockaddr *)&in4_addr, sizeof(in4_addr), 0);
if (ret) {
pr_err("failed to connect: %d!\n", ret);
return ret;
}
/* We can send up to 17 frags */
flags = MSG_MORE;
for (i = 0; i < 17; i++) {
if (i == 16)
flags = MSG_EOR;
pages[i] = alloc_pages(GFP_KERNEL | __GFP_COMP, 1);
if (!pages[i]) {
pr_err("out of memory!");
goto free_pages;
}
sock->ops->sendpage(sock, pages[i], PAGE_SIZE -1, 2, flags);
}
free_pages:
for (; i > 0; i--)
__free_pages(pages[i - 1], 1);
printk("sendfb_init: test done\n");
return -1;
}
module_init(sendfb_init);
MODULE_LICENSE("GPL");
A try to load such module results in multiple
'kernel: hv_netvsc vmbus_15 eth0: Packet too big: 100' messages as all retries
fail as well. It should also be possible to trigger the issue from userspace, I
expect e.g. NFS under heavy load to get stuck sometimes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In netvsc_start_xmit() we can handle packets which are scattered around not
more than MAX_PAGE_BUFFER_COUNT-2 pages. It is, however, easy to create a
packet which is not big in size but occupies more pages (e.g. if it uses frags
on compound pages boundaries). When we drop such packet it cases sender to try
resending it but in most cases it will try resending the same packet which will
also get dropped, this will cause the particular connection to stick. To solve
the issue we can try linearizing skb.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... which validly uses dev_kfree_skb_any() instead of dev_kfree_skb().
Setting ret to -EFAULT and -ENOMEM have no real meaning here (we need to set
it to anything but -EAGAIN) as we drop the packet and return NETDEV_TX_OK
anyway.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shradha Shah says:
====================
sfc: Nic specific sriov functions, netdev_ops and sriov_configure
First two patches among the series of patches to support SRIOV on EF10.
First patch declares nic specific sriov functions in nic specific headers,
creates only one instance of the netdev_ops, removes sriov functionality
from Falcon code.
Second patch adds support for sriov_configure.
The Virtual Functions can be enabled but they do not bind to the SFC
driver just yet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
