The CEC specification requires that the Vendor ID (if any) is reported
after a logical address was claimed.
This was never done, so add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC IP is very similar between the three HDMI receivers, but
not identical. Add support for all three variants.
Tested with an adv7604 and an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a filehandle is dup()ped, then it is possible to close it from one fd
and call mmap from the other. This creates a race condition in vb2_mmap
where it is using queue data that __vb2_queue_free (called from close())
is in the process of releasing.
By moving up the mutex_lock(mmap_lock) in vb2_mmap this race is avoided
since __vb2_queue_free is called with the same mutex locked. So vb2_mmap
now reads consistent buffer data.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: syzbot+be93025dd45dccd8923c@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return 0 when invalidating the logical address. The cec core produces
a warning for drivers that do this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Torbjorn Jansson <torbjorn.jansson@mbox200.swipnet.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the tx_ignore_nack_until_eom error injection was activated,
then tx_nacked was never set instead of setting it when the last
byte of the message was transmitted.
As a result the transmit was marked as OK, when it should have
been NACKed.
Modify the condition so that it always sets tx_nacked when the
last byte of the message was transmitted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Documentation and code was linking the old documentation at:
http://v4l2spec.bytesex.org/spec/x1904.htm
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/staging/media/sunxi/cedrus/cedrus.c:421:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 50e761516f ("media: platform: Add Cedrus VPU decoder driver")
CC: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The R-Car CSI-2 interface has a number of selectable 'channels' that
provides pixel data to the VINs during image acquisition.
Each channel can be used to match a CSI-2 data type and a CSI-2 virtual
channel to be routed to output path.
Different SoCs have different number of channels, with R-Car E3 being the
notable exception supporting only 2 of them.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for R-Car E3 R8A77965 to R-Car CSI-2 driver.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add R-Car E3 R8A77990 SoC to the rcar-vin supported ones.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add compatible string for R-Car E3 R8A77990 to the list of SoCs supported by
rcar-vin driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Improve the pxp_soft_reset() error message by moving it to the
caller function, associating it with a proper device and also
by displaying the error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
pxp_soft_reset() may fail with a timeout, so it is better to propagate
the error in this case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In addition to the S_FMT debug output, S_SELECTION (SEL_TGT_CROP) is
relevant to determine encoded size. Add debug output for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Consistently add the context index to debug output, which otherwise is
impossible to make sense of when two contexts are running concurrently.
For this purpose, add a convenience macro coda_dbg(). Use the function
name with the coda_ prefix stripped as keyword where applicable, and
consistently use vid-out and vid-cap names for the queues. Add sequence
counters to the decoder job finished message and correctly indicate B
frames. Add a start streaming message to complement the stop streaming
message and a start encoding message to complement the existing start
decoding message.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use v4l2_type_names to indicate which of the two queues is busy.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error code looks much more like a bit field than an error value.
Print it as hex rather than decimal.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance complains if G_PARM returns 0 in the denominator.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance complains about S_PARM being supported, but not
ENUM_FRAMEINTERVALS.
Report a continuous frame interval even though the hardware only
supports 16-bit numerator and denominator, with min/max values
that can be programmed into the mailbox registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The flag is already set in coda_g_parm, but v4l2-compliance complains
about it not being set during S_PARM.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CODA driver uses threaded IRQs only, so there is nothing happening
in hardirq context that could interfere with the buffer meta handling.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The per-device instance list is unused, remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Three macroblocks seem to be the minimum resolution that can be encoded
and decoded by the CODA960 h.264 codec. Picture run commands fail for
smaller resolutions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ringbuffer used to hold the bitstream is very conservatively sized,
as keyframes can get very large and still need to fit into this buffer.
This means that the buffer is way oversized for the average stream to
the extend that it will hold a few hundred frames when the video data
is compressing well.
The current strategy of queueing as much bitstream data as possible
leads to large delays when draining the decoder. In order to keep the
drain latency to a reasonable bound, try to only queue a full reorder
window of buffers. We can't always hit this low target for very well
compressible video data, as we might end up with less than the minimum
amount of data that needs to be available to the bitstream prefetcher,
so we must take this into account and allow more buffers to be queued
in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bitstream prefetch unit reads data in 256 byte blocks with some kind
of queueing. For the decoder to see data up to a desired position in the
next run, the bitstream has to be filled for 2 256 byte blocks past that
position aligned up to the next 256 byte boundary.
This should make sure we never run into a buffer underrun condition if
userspace does not supply new input buffers fast enough.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Storing the unmasked kfifo->in position as meta->start and ->end allows
to more easily compare a point past meta->end with the current
kfifo->in.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ffz() return value is undefined if the instance mask does not
contain any zeros. If it returned 32, the following set_bit would
corrupt the debugfs_root pointer.
Switch to IDA for context index allocation. This also removes the
artificial 32 instance limit for all except CodaDx6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Swapping the order between v4l2 subdevice registration and checking chip
id in b7a417628a ("media: ov2680: don't register the v4l2 subdevice
before checking chip ID") makes the mode restore to use the sensor
controls before they are set, so move the mode restore call to s_power
after the handler setup for controls is done.
This remove also the need for the error code path in power on function.
Fixes: b7a417628a ("media: ov2680: don't register the v4l2 subdevice before checking chip ID")
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document that changing the frame interval has no effect on frame size.
While this was the assumption in the API, it was not documented as such.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The first device that used that IP was the A31. Add it to our list of
compatibles.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The H3 has a slightly different CSI controller (no BT656, no CCI) which
looks a lot like the original A31 controller. Add a compatible for the A31,
and more specific compatible the for the H3 to be used in combination for
the A31.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are a few other coding style issues reported by checkpatch
while in --strict mode. Fix the ones that make sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make checkpatch.pl happier by running it on strict mode and
using the --fix-inline to solve some issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allwinner V3s SoC features a CSI module with parallel interface.
This patch implement a v4l2 framework driver for it.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov7670's v4l2 controls.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov5640's v4l2 controls.
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov2640's v4l2 controls.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov2640 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
[Sakari Ailus: Use "Eight Vertical Colour Bars" as the second manu entry]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mt9m111 has special camera effects feature. This makes use of
it through V4L2_CID_COLORFX control.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for mt9m111's v4l2 controls.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
change bayer order when using test pattern mode.
remove test pattern mapping method
[Sakari Ailus: Drop extra added newline]
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The NATIVE_SIZE target is documented for mem2mem devices but no driver has
ever apparently used it. It may be never needed; remove it for now.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when a variable is assigned to itself:
drivers/media/i2c/imx214.c:695:13: error: explicitly assigning value of
variable of type 'const struct reg_8 *' to itself
[-Werror,-Wself-assign]
for (table = table; table->addr != IMX214_TABLE_END ; table++) {
~~~~~ ^ ~~~~~
1 error generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for formats with 4 planes: V4L2_PIX_FMT_ABGR32,
V4L2_PIX_FMT_ARGB32.
Also add alpha plane related flags to the header of the encoded file.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hans.verkuil@cisco.com: fix line-too-long warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
