Since the macaddr add and delete happens asynchronously, error
messages don't easily get associated to the actual request. Here
we add a bit of information to the error messages to help
determine the source of the error.
Change-ID: Id2d6df5287141c3579677d72d8bd21122823d79f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the need for a reset when the device enters limited promiscuous
mode. This was causing heartburn for people who were using VFs and
bridging, since this would require all of the VFs to undergo a reset
each time the PF changed its promiscuity.
Change-ID: I0a83495c5e4d68112bbc7a7a076d20fa8dd3b61c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always add MAC address at the tail of the MAC filter list. Since the
device's "real" MAC address is added first, it will always be at the
beginning of the list. This prevents an issue where the "real" MAC
filter might not get added if too many other filters are added before
bringing the interface up.
Change-ID: I34a8aeebeb0cb87a44b24118adc4176c7b943c1c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Limiting qcount to pf->num_lan_msix, effectively limits the RSS queues
to only use the number of CPUs, and ignore all other queues. We don't
want to do this. If the user has changed the RSS settings to use more
queues then CPUS, we want to trust they know what they are doing and
let them. More importantly, if we tell them that is what we did, we want
to actually do it and allow traffic into all of the queues we have
allocated. This does not change the default setting to initially
allocate only the number of CPUS of queue pairs.
Change-ID: Ie941a96e806e4bcd016addb4e17affb46770ada5
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removing this code which wasn't allowing 100BaseT to show up in the supported
link modes for 10GBaseT PHYs.
Change-ID: Iada2eafa7ef6b4bac9a2a1380ff533ae5de51e1d
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a Direct Attach (DA) cable is used, if the i40e_set_settings
function is called it would return an error. Add the DA type so
the function won't fail.
Change-ID: I2b802f27a5d91cfefa72fd1f852acb4d74647a8e
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function was failing to save PCI state
and this would result in a kernel stack trace from a WARN_ONCE in the
pci_legacy_suspend() function.
Add a call to pci_save_state() to fix that problem.
Change-ID: I4736e62bb660966bd208cc8af617a14cb07fc4bd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function calls another function that preps the device
for the power save and resume by freeing all the Tx/Rx resources and
interrupts but that function does not free the "other" causes interrupt
vector and IRQ. It also fails to call synchronize_irq() before freeing
the IRQ vectors. This sometimes may result in some AER errors on those
systems with that PCIe error reporting feature enabled.
Call synchronize_irq() before freeing IRQ vectors and explicitly free
the other causes interrupt resources and shut down that MSIX interrupt.
Change-ID: Ib88e4536756518a352446da0232189716618ad81
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user adds an obscene amount of MAC addresses, the driver will run
into the situation where it has too many address requests to fit into a
single PF message. The driver checks for this case, and calculates the
maximum number of messages that it can send. Then it completely ignores
this count and overflows the buffer.
Fix this by checking the address count and bailing out of the loop at
the appropriate time.
Change-ID: If8dcbb04602c75941dc0cd8309065e1de9ca791c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were failing to set the client interface down when we put the VSI
down. Add this call so that the client doesn't get an open called with
no close.
Also remove an un-needed delay. The VF should not be affected at all by
i40e_down.
Change-ID: I1135dffef534bf84e6fed57cf51bcf590e6cfaf7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that VF RSS is configured by the PF driver, it needs to set the RSS
Hash Enable registers by default. Without this, no packets will be
hashed and they'll all end up on queue 0.
Change-ID: I38e425f40ddb81e3b19a951cfbb939fa5b1123f1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function uses the i40e_hw struct all over the place, so why doesn't
it keep a pointer to the struct? Add this pointer as a local variable
and use it consistently throughout the function.
Change-ID: I10eb688fe40909433fcb8ac7ac891cef67445d72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functions to enable and disable default VSI on a VEB. This allows
for configuration of limited promiscuous mode specifically for bridging
purposes.
Change-ID: I0cc5bd68b31c500fdff4d47e1f15d50d2739faf4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no prevention of a concurrent call to both fixed_mdio_read()
and fixed_phy_update_state(), which can result in the state being
modified while it's being inspected. Fix this by using a seqcount
to detect modifications, and memcpy()ing the state.
We remain slightly naughty here, calling link_update() and updating
the link status within the read-side loop - which would need rework
of the design to change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate software phy registers as and when requested, rather than
duplicating the state in fixed_phy. This allows us to eliminate
the duplicate storage of of the same data, which is only different
in format.
As fixed_phy_update_regs() no longer updates register state, rename
it to fixed_phy_update().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate out the generation of MII registers from the state validation.
This allows us to simplify the error handing in fixed_phy() by allowing
earlier error detection.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the swphy register generation to tabular form which allows us
to eliminate multiple switch() statements. This results in a smaller
object code size, more efficient, and easier to add support for faster
speeds.
Before:
Idx Name Size VMA LMA File off Algn
0 .text 00000164 00000000 00000000 00000034 2**2
text data bss dec hex filename
388 0 0 388 184 swphy.o
After:
Idx Name Size VMA LMA File off Algn
0 .text 000000fc 00000000 00000000 00000034 2**2
5 .rodata 00000028 00000000 00000000 00000138 2**2
text data bss dec hex filename
324 0 0 324 144 swphy.o
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fixed_phy MII register generation to a library to allow other
software phy implementations to use this code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXa6rGAAoJED07qiWsqSVqzwsH/0g/blikQuNNAB7LzXGTEMn8
ipWCODaYxgWE/V/1A0JjsKpxB1ZL3HE0/xg/OmZ10SRNlz5LJTLkoYZa7xYmyxtT
a89mT9vdnWxwfwbeIhSSjG9W9g44vqrhMIPxffIu5yqSqdIJak0HIiuQizJ0/xjx
xQVx4AykWKQ3u0/Tiyz3ez5yhyMMNEmHxKyDWpgrR6+zXlofwP/Em3NFPwk9gh32
ECAagOUOEvdjXeRs1Yn/CV0FC7Wgs4Hzr048JJ5wOteawBLr+sPOnuWZtDhNrwDK
Eceh7aEeAiFfIW+jCMEe5qrpFHi8hqyqBo4L9TDYsE7T/Z6BPyh+5OUh8+5dtaw=
=TZew
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.8-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 4 patches for net-next/master.
Arnd Bergmann's patch fixes a regresseion in af_can introduced in
linux-can-next-for-4.8-20160617. There are two patches by Ramesh
Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver.
And a patch by Ed Spiridonov that adds better error diagnoses messages
to the Ed Spiridonov driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXa6kLAAoJED07qiWsqSVqRsIH/RiHvKa9VB7yYQaXV3YqUPIo
iizU6mQCeODqZsDw9bXce232RevKBteYDyr4YpC4f9mX54CrQI7WRN7ev5fKU49a
FB4M9uz8v3kS5XX8gADkuDvSwtrQ7pMz1fXM2rkEyHT/xf6egCOT/lpI/mWQuNcM
3mkMFLy5ZUAaVHAsfqu8TrDgeWMDXNxbVwGtB/AuoFJ62pqVf5M+TwzKrYaOFM4r
Rbl3NINKwFwk41KCOz20GiVvvahCp05SPHmK0OMwxsffKZmmkUOdHvusOZx7Zxnw
RY7Mc/j+OvvAHYnRaZmfdDEPXc2hKQP0ATjVsW/bju7PWoVpG+87mYqubIFuTSY=
=B2gO
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.7-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-06-23
this is a pull request of 3 patches for the upcoming linux-4.7 release.
The first two patches are by Oliver Hartkopp fixing oopes in the generic CAN
device netlink handling. Jimmy Assarsson's patch for the kvaser_usb driver adds
support for more devices by adding their USB product ids.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, mdiobus_alloc() sets the PHYs to polling mode, but a
pointer size memcpy means that a couple IRQs end up being overwritten
with a value of 0. This means that PHY_POLL is disabled and results
in unpredictable behavior depending on the PHY's location on the
MDIO bus. Remove that memcpy and the now unused phy_irq member to
force the SMSC911x PHYs into polling mode 100% of the time.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fixes to spelling mistakes of the words "excessive collisions"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fixes to spelling mistakes of the word "descriptors"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.
Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new get/set link ksettings and remove get/set settings legacy
callbacks.
This allows us to use bitmasks longer than 32 bit for supported and
advertised link modes and use modes that were previously not supported.
Signed-off-by: Gal Pressman <galp@mellanox.com>
CC: Ben Hutchings <bwh@kernel.org>
CC: David Decotigny <decot@googlers.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MLX5E_50GBASE_SR2 as ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this mode the moderation timer will restart upon
new completion (CQE) generation rather than upon interrupt
generation.
The outcome is that for bursty traffic the period timer will never
expire and thus only the moderation frames counter will dictate
interrupt generation, thus the interrupt rate will be relative
to the incoming packets size.
If the burst seizes for "moderation period" time then an interrupt
will be issued immediately.
CQE based moderation is off by default and can be controlled
via ethtool set_priv_flags.
Performance tested on ConnectX4-Lx 50G.
Less packet loss in netperf UDP and TCP tests, with no bw degradation,
for both single and multi streams, with message sizes of
64, 1024, 1472 and 32768 byte.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an infrastructure for getting/setting private net device
flags.
Currently a 'nop' priv flag is added, following patches will override
the flag will actual feature specific flags.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_maxrate ndo.
Use the rate index from the hardware table to attach to channel SQ/TXQ.
In case of failure to configure new rate, the queue remains with
unlimited rate.
We save the configuration on priv structure and apply it each time
Send Queues are being reinitialized (after open/close) operations.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring and managing HW rate limit tables.
The HW holds a table of rate limits, each rate is
associated with an index in that table.
Later a Send Queue uses this index to set the rate limit.
Multiple Send Queues can have the same rate limit, which is
represented by a single entry in this table.
Even though a rate can be shared, each queue is being rate
limited independently of others.
The SW shadow of this table holds the rate itself,
the index in the HW table and the refcount (number of queues)
working with this rate.
The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate.
Number of different rates and their values are derived
from HW capabilities.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates year and company name in the copyright markings in the
be2net source files.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3
vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes
broadcast and multicast packets back to PF's vport confusing the
Linux bridge. BE3 relies on the src-mac addr being programmed on the
interface to avoid sending back an echo of a broadcast or multicast packet
on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the
VM behind the bridge doesn't get configured on the vPort and so echo
cancellation doesn't work.
This patch worksaround this problem by disabling the EVB initially
and re-enabling it *only* when SR-IOV is enabled by the user. For the
driver fix to work, the BE3 FW version must be >= 11.1.84.0.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net so far supported creation of RX/TX queues only in pairs.
On configs where rx and tx queue counts are different, creation of only
the lesser number of queues has been supported.
This patch now allows a combination of RX/TX-only channels along with
combined channels. N TX-queues and M RX-queues can be created with the
following cmds:
ethtool -L ethX combined N rx M-N (when N < M)
ethtool -L ethX combined M tx N-M (when M < N)
Setting both RX-only and TX-only channels is still not supported.
It is mandatory to create atleast one combined channel.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EQs available on a function are shared between NIC and RoCE.
The be_max_eqs() macro was so far being used to refer to the max number of
EQs available for NIC. This has caused some confusion in the code. To fix
this confusion this patch introduces a new macro called be_max_nic_eqs()
to refer to the max number of EQs avialable for NIC only and renames
be_max_eqs() to be_max_func_eqs().
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
So, add new quirk flag to judge the supported features.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ddr_timeout during device init.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for private flags for the driver.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has minor changes for proper ptp info retreival.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for host driver support for new Xaui
interfaces.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds extensive support of statistics for data path,
control path and firmware.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has new tx/rx interrupt moderation defaults of
count/timer for better throughput and utilisation.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves the order of chip reset while destroying
the resources by postoponing soft reset in destroy resources
function until all queues are removed properly.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new state so that the ctrl packets are not sent
to firmware during unload time and only rx packets are allowed.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has firmware image related changes for: firmware
release upon failure, support latest firmware version and
firmware download in 4MB chunks.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Patch adds tx buffer handling to Napi along with RX
traffic. Also separate spinlocks are introduced for handling
iq posting and buffer reclaim so that tx path and tx interrupt
do not compete against each other.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds supports for Vlan filtering for liquidio driver.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for vlan offloads for the driver and
receive header structures are also modified appropriately. Also
requestID will not be used in reveive header any more.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the limits of soft command buffer size and
num command buffers. This patch also has changes for queue macros
and limit related changes for new chips.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use the
mailbox facility at the same time. The issue is the for the Virtual
Function Driver, the only way to get the Virtual Interface statistics
is to issue mailbox commands to ask the firmware for the VI Stats.
And, because the VI Stats command can only retrieve a smallish number of
stats per mailbox command, we have to issue three mailbox commands in quick
succession. When ethtool or netstat command to get interface stats and
interface up/down is run in a loop for every 0.1 sec, we observed
mailbox collisions. And out of the two commands one would fail with
the present code, since we don't queue the second command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at the
head issue the mailbox command, else wait for the existing command to
complete. Usually command takes less than a milli-second to complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be very
rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations, it will be hard to
distinguish portions of code supporting a single-chip or a switch fabric
of interconnected chips.
Make the code clearer now, by renaming the mv88e6xxx_priv_state chip
structure to mv88e6xxx_chip. This patch brings no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations and other mv88e6xxx
enhancements, new files will be added.
Similarly to mlxsw or b53, move mv88e6xxx files into their own folder.
In the meantime, update the MAINTAINERS entry to please checkpatch.pl,
by replacing the invalid 88E6352 entry with 88E6XXX, maintained by
Andrew and myself.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the device tx/rx coalescing
timeout values in the order of micro seconds. It also adds APIs for
upper layer drivers for reading/updating the coalescing values.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRfMAAoJEG4XJFUm622bxwEH/iZm3o752MM62fJyCOEtEN6R
8vL7kyehX81G9szQyQ7bMQ7y0diobeBGsu8e7zzV4Mt+cU0Z9g/ezfca6HfE6Hrh
0ubKl/tSzAhRcAoQiNyKOI36yt455r1Mnr8a18OYO79pnNcjf7kSd7pJG2BW0Hdx
dRsSxzcg+E0w4z7mJ/cgM5aRzjXmXvAUjw9cIt36y3+ng1fQ+M782lkCtscMZY3Q
e5bkLCaP5TG+O9niPTjzrAzMlBTGwopknuEZnwIGDkNkx1PeBzRATVGeSa9Zba6d
g17kGbP7QT1GaCJF/FfWColaVpMBDhviovQANeoaUi804C4ZKNZAcJirZC3W2eM=
=uYcn
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.8
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
rtl8xxxu
* fix typo on variable name
ath10k
* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind
ath9k
* fix GPIO mask regression for AR9462 and AR9565
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRGeAAoJEG4XJFUm622bc6MH/jBpajTua8/fEUwo8dEywKRD
HULV6h5jDfoQ2N+LkKGff4UoAup4rWvzsXgTsNwPrma+TYi8M/eVrWanJ+TkwI31
2jHh2ynBqAPNhM6oT/NKJgGPgamFsa7mvtM8wBZV4VZseIGhJcKExExLjnE64ZdG
7o6VrtNRNtP+lnxT7ojbcS7cMnQqa7d32CqYjyJtABzLdSHNdww9euHLo9t6EFFa
7dti3t4WftTZ0+VyZmNrLgS+RO0ix7Kbr+ZfNQPyq9DLAaSfNZR8kWpNZjR7G4BA
QYffAkBO/iwffJS9b/VU+o8b32SV0TstTbJsEyvJcqkkTbngj2QhHZHBU012vQk=
=uVoM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.7
iwlwifi
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
rtl8xxxu
* fix typo on variable name
ath10k
* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind
ath9k
* fix GPIO mask regression for AR9462 and AR9565
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for reading and updating priority flow
control (PFC) attributes in the driver via netlink.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx errors present summation of errors encountered while transmitting
packets.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment of rth->dst.output in vrf_rt6_create() and
vrf_rtable_create() used a hard tab before the '='. The neighboring
assignments did not. Make the assignment of rth->dst.output consistent
with the surrounding code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a typo we would always be using the MIB counter width of the
first element of the counter array instead of the current element, and
we would always be accessing the register statistics with a 64-bits
read, while some could be 32-bits. This got unnoticed in testing with
MDIO and SRAB which tolerate doing this, but testing with the SPI bus
revealed bogus values being returned. Fix this by using the proper
iterator here.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual MAC devices don't necessarily have both MACs wired up, so ignore
those that are disabled.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silent ignorance of errors during probe procedure is a bad thing, this
patch fixes it. Extra message added for hardware initialization
failure. Such common issues are mostly caused by wrong wiring. Message
about success added as well, it should be useful to debug new hardware
configuration, especially in case of several CAN buses.
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As per Wolfgang G, all new drivers should support decreasing state
transition(back-to-error-active). This patch adds this support.
This driver configures the controller to halt on bus-off entry. Hence,
when in error states less than bus off state, the TEC/REC counters
are checked for lower state transition eligibility and action.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The controller can operate in one of the two global modes
- CAN FD only mode (default)
- Classical CAN (CAN2.0) only mode
This patch adds support for Classical CAN only mode. It can be enabled
by defining the optional device tree property "renesas,no-can-fd" of this
node.
Note: R-Car Gen3 h/w manual v0.51E shows bit6 of RSCFDnCFDGCFG as
reserved, which is incorrect. This bit is same as RSCFDnGCFG.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Kvaser Leaf Light HS v2 OEM, Mini PCI
Express 2xHS and USBcan Light 2xHS.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With upstream commit bb208f144c (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This allows a clean shutdown, even if some netdev clients do not
release their reference from this netdev. It is enough to release
the HW resources only as the kernel is shutting down.
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify mlx4_en_vlan_rx_[add/kill]_vid to return error value in case of
failure.
Fixes: 8e586137e6 ('net: make vlan ndo_vlan_rx_[add/kill]_vid return error value')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both dev_uc_sync_multiple() and dev_mc_sync_multiple() require the
source device to be locked by netif_addr_lock_bh(), but this is missing
in team's enslave function, so add it.
This fixes the following lockdep warning:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(_xmit_ETHER/1);
local_irq_disable();
lock(&(&mc->mca_lock)->rlock);
lock(&team_netdev_addr_lock_key);
<Interrupt>
lock(&(&mc->mca_lock)->rlock);
*** DEADLOCK ***
Fixes: cb41c997d4 ("team: team should sync the port's uc/mc addrs when add a port")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).
Therefore, instead check the VID parameter to test whether a port is a
vPort or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vPort is created or when it joins a bridge we always do the same
set of operations:
1) Create the vFID, if not already created
2) Setup flooding for the vFID
3) Map the {Port, VID} to the vFID
When a vPort is destroyed or when it leaves a bridge the reverse is
performed.
Encapsulate the above in join / leave functions and simplify the code.
FIDs and rFIDs will use a similar set of functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FID used by a vPort (vFID, but also rFID later in the series) is
always mapped using {Port, VID} and not only VID as with the 4K FIDs of
the VLAN-aware bridge.
Instead of specifying all the arguments each time, just wrap this
operation using a dedicated function and simplify the code.
As before, the function takes FID as its argument in preparation for a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and use only one function for vFID creation /
destruction.
Unlike before, the function receives a FID index as its argument and not
a vFID index. Instead of passing 0, now one would need to pass 4K, which
is the first vFID.
This is the first step in creating a generic FID struct that will be
used for all three types of FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a macro to do this kind of declarations, so use it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold a reference count on the number of ports member in the
VLAN-aware bridge, as we only support one.
Instead of always incrementing / decrementing the reference count after
joining / leaving the bridge, simply do this accounting in the join /
leave functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'br_dev' is never used, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When responding to unlinking CHANGEUPPER notifications we shouldn't
return any value, as it's not checked by upper layers.
In addition, there's nothing the driver can do in case of failure, so it
should simply continue and try to free as much resources as possible and
not stop on first error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking for a condition and then issue the warning, just do
it in one go and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When upper device of a VLAN device changes we already made sure it's
a bridge device in PRECHANGEUPPER, so no need to check it's a master
device in CHANGEUPPER.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port netdev is put under LAG it cannot have VLAN upper devices,
so forbid that. The LAG device itself can have VLAN upper devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only support the following upper devices for port netdevs:
1) Bridge
2) LAG (bond / team)
3) VLAN
Any other device is forbidden, so return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the error value and returning NOTIFY_BAD, just use
notifier_from_errno() and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable/disable tso, the driver tries to access the hardware register,
but this operation will cause the port unavalible when there is traffic.
This patch tries to enable TSO when initialize, then control tso through
TSE bit in transmit descriptor.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default coalesce timeout is 3us, which is will cause CPU
usage is too high. This patch change it to 50us in order to reduce
CPU usage and the value makes sure network latency also meets requirement.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default sbm config parameter leaves little buffer when there is heavy
traffic, which will cause packets drop. This patch changes them to make
enough buffers for handling packets.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and
read new fbd_num to start new receive cycle. It recomputes cycle num is
fbd_num minus clean_count, actually this cycle num is too big because
it drop out receive cycle. It brings about the port unavailable.
So we will goto out when alloc skb fail to fix this bug.
Signed-off-by: Jun He <hjat2005@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default driver sets anchor led bit to 0 when link down,
actually, the anchor bit should be set to 1, so fixes it when
link status is down.
Secondly, change the return value of cpld_set_led_id to 0, which
means leave the cpld to control led blink frequece other than the
driver itself.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver stores the high bit value of tcam data register
to the tcam data low element, stores the low bit value of tcam data
register to tcam data high element, this patch fixes this bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds spin lock for tcam table operation,
there maybe a race condition happens when more than
one thread try to change the tcam talbe entries.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC,
so change the statistics of pfc pause in dsaf and remove the old
pfc pause frame statistics.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug-ports,there are two non-synchronized processes:
Speed-Auto-Negotiation and Link-Update-Status. The two
processes are towed by two different state machines.
Bond reads the speed when link up, but the speed maybe
not update the right value at that time.That make for bond's
wrong speed. Thus only one state machine should be used and
if phy_state_machine is used, it does not need to do
hns_nic_update_link_status().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ethtool cmd(ethtool -t ethx) again and again for a long
time, it will be probabilistically fail. The PHYs' registers may
be on different pages, so it must be switch to the right page
before setting PHYs' registers.
And __lb_up() calls phy_start() to startup the PHYs device, but
this function may change Copper Control Register(Page 0, Register 0)
to an other value. It would cause phy loopback test fail. if we
remove phy_start(), we have to remove the relative phy_stop(),
phy_disconnect() when doing phy loopback to keep the phy stay in
right status.
Reported-by: hejun <hjat2005@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Hilink3 and Hilink4 use the same xge training and xge u adaptor for
HNSv2, it needs to select which Hilink to be set before relative serdes
being configed. The hilink_access_sel is the register to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error info should be printed as "set mask to 64bit fail!" instead of
"set mask to 32bit fail!" in dma_set_mask_and_coherent().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource, it will unmap the map
automatically, remove the unnecessary the resource free.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The annotation info for hns_nic_reset_subtask() should be
"for resetting subtask" instead of "for resetting suntask".
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS receives a packet without doing anything, but it should call
skb_reset_mac_header() to initialize the header before using
eth_hdr().
Fixes: 0d6b425a37
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For service port, hns dsaf v1 support to close tx_pause.
However, the port will be invalid when it run command
ethtool to close tx_pause. This patch will fix it.
Signed-off-by: Qianqian Xie <xieqiaqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit fileds of PPE reset register are different between HNS v1 and
HNS v2, but the current procedure just only match HNS v1. Here is a
patch to fix it.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the SMI address of the switch chip is zero, the chip assumes to be
the only one on the SMI master bus and thus responds to all its known
SMI devices addresses (port registers, Global2, etc.)
When its SMI address is not zero, some chips (e.g. 88E6352) use an
indirect access through two SMI Command and Data registers.
Other models (e.g. 88E6060) using less than 16 internal SMI addresses
always use a direct access.
Add a capability flag to describe chips supporting the (indirect)
Multi-chip Addressing Mode, and a low-level API to access the registers
via SMI.
Other accesses (like Ethernet management frames) may be added later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch ID is located at address 0x3 of every Port Registers bank.
But not all Marvell switches have their Port Registers SMI Addresses
starting at 0x10. 88E6060 starts at 0x8 and 88E6390 starts at 0x0.
Add this data in the info structure and use it in the detection code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allocating the chip structure, pass it a compatible info pointer.
The compatible info structure will be used later to describe how to
access the switch registers and where to read the switch ID.
For the standard MDIO probe, get it from the device node data. For the
legacy DSA driver probing, pass it the 88E6085 info.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the common detection code which assigns the info structure to
the chip given the read switch ID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper function to isolate SMI specific assignments and checks.
This function will later help choosing the different SMI accesses based
of the compatible info.
Since the chip structure is already allocated in the legacy probe, use
the mv88e6xxx_reg_read access routine instead of __mv88e6xxx_reg_read.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper function to allocate the chip structure at the beginning
of the probe functions. It will be used to initialize the SMI access.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip smi_mutex mutex is used to protect the access to the internal
switch registers, not only the Multi-chip Addressing Mode, as commented.
Since we will isolate SMI-specific pieces of code, avoid the confusion
now by renaming smi_mutex to reg_lock. No functional changes here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_table array and the mv88e6xxx_lookup_info function are
static, so remove the table and size arguments from the lookup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the optional variant to get the reset GPIO line, instead of checking
for the -ENOENT error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mixed assignments, allocations and registrations in the probe code
make it hard to follow the logic and figure out what is DSA or chip
specific.
Extract the struct dsa_switch related code in a simple
mv88e6xxx_register_switch helper function.
For symmetry in the code, add a mv88e6xxx_unregister_switch function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO device probe and remove functions are respectively incrementing
and decrementing the bus refcount themselves. Since these bus level
actions are out of the device scope, remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the MDIO probing function, dev is already assigned to &mdiodev->dev
and np is already assigned to mdiodev->dev.of_node, so use them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip->ds and ds->slave_mii_bus assignments are common to both legacy
and new MDIO probing and are already done in the later setup code.
Remove the duplicated assignments from the MDIO probing code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 5 style problems reported by checkpatch:
WARNING: suspect code indent for conditional statements (8, 24)
#492: FILE: drivers/net/dsa/mv88e6xxx.c:492:
+ if (phydev->link)
+ reg |= PORT_PCS_CTRL_LINK_UP;
CHECK: Logical continuations should be on the previous line
#1318: FILE: drivers/net/dsa/mv88e6xxx.c:1318:
+ oldstate == PORT_CONTROL_STATE_FORWARDING)
+ && (state == PORT_CONTROL_STATE_DISABLED ||
CHECK: multiple assignments should be avoided
#1662: FILE: drivers/net/dsa/mv88e6xxx.c:1662:
+ vlan->vid_begin = vlan->vid_end = next.vid;
WARNING: line over 80 characters
#2097: FILE: drivers/net/dsa/mv88e6xxx.c:2097:
+ const struct switchdev_obj_port_vlan *vlan,
WARNING: suspect code indent for conditional statements (16, 32)
#2734: FILE: drivers/net/dsa/mv88e6xxx.c:2734:
+ if (mv88e6xxx_6352_family(ps) || mv88e6xxx_6351_family(ps) ||
[...]
+ reg |= PORT_CONTROL_EGRESS_ADD_TAG;
total: 0 errors, 3 warnings, 2 checks, 3805 lines checked
It also rebases and integrates changes sent by Ben Dooks [1]:
The driver has a number of functions that are not exported or
declared elsewhere, so make them static to avoid the following
warnings from sparse:
drivers/net/dsa/mv88e6xxx.c:113:5: warning: symbol 'mv88e6xxx_reg_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:167:5: warning: symbol 'mv88e6xxx_reg_write' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:231:5: warning: symbol 'mv88e6xxx_set_addr' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:367:6: warning: symbol 'mv88e6xxx_ppu_state_init' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3157:5: warning: symbol 'mv88e6xxx_phy_page_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3169:5: warning: symbol 'mv88e6xxx_phy_page_write' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3583:26: warning: symbol 'mv88e6xxx_switch_driver' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx.c:3621:5: warning: symbol 'mv88e6xxx_probe' was not declared. Should it be static?
[1] http://patchwork.ozlabs.org/patch/632708/
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds basic support for the bytewerk.org candleLight interface,
a open hardware (CERN OHL) USB CAN adapter.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'MODULE_FIBER' value replaced several other FIBER values
in newer management firmware images, so existing code would
fail to properly reflect its mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has 2 sets of entries for handling ramrod configurations
toward firmware - a regular pre-allocated set of entires and a
possible 'unlimited' list of additional pending entries.
In most scenarios the 'unlimited' list would not be used, but
when it does the handling of the ramrod completion doesn't
properly handle the release of the entry.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal loopback in driver is based on two things - first
is the willingness of transmitter to use it [in case of VFs,
this can be forced based on VEPA/VEB] and secondly on another
vport classification configuration which should match the
packet's destination.
Current code allows non-linux VFs to configure a 'promisc'
mode on Tx, meaning all traffic sent by VF would be loopbacked
internally by firmware; This isn't considered a valid mode and
as such should be prevented by PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no vlan filter is configured, firmware has a configurable
default on whether to pass only untagged packets or all packets
regardless of their tagging. Driver currently doesn't set this
field in the necessary ramrod, causing the default to always be
'receive all'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
Calling sdio_claim_host() from the interface independent part of
the mwifiex driver is not only a layering violation, but also causes
a link error if MMC support is disabled, or if CONFIG_MMC=m
and CONFIG_MWIFIEX=y:
drivers/net/built-in.o: In function `mwifiex_fw_dpc':
:(.text+0xff138): undefined reference to `sdio_claim_host'
:(.text+0xff158): undefined reference to `sdio_release_host'
The right way to do this is to have the sdio specific code in the
sdio driver front-end, and we already have a callback pointer that
we can use for this after exporting the generic fw download
function from the core driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 65c71efe1c ("mwifiex: fix racing condition when downloading firmware")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion to the 64-bit time based ptp methods left two instances
of 'struct timespec' in place. This is harmless because 64-bit
architectures define timespec64 as timespec, and this driver is
not used on 32-bit machines.
However, using 'struct timespec64' directly is obviously the right
thing to do, and will help us remove 'struct timespec' in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b9acf24f77 ("ptp: tilegx: convert to the 64 bit get/set time methods.")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXZAIqAAoJED07qiWsqSVqW0YH/RMgC6CDlJUtHr7+B8YLpi0e
BZOzAHH7mQdP+Z2kIXZp8Dnziq5G8heWNjRwTMPLHvOel+oms+0ZK6VY/kJYArdb
ViGGgi/gQ334JGqJYi2utkyIIIRH7ZxwcblF1aaaFVfFy7tZMVuppIWVzR/V0Gje
/5FftT1f04/6iumEq4es+Jb0OC9azoebSs1DUZTIvYOz3XrnCbB1FdmDN+a3xZKC
Qyav6QVnp/m2InzGSN+Kd/W++EP6YckdBp/++2hizsOvSIOfe8GRqkc0r7fLbfZ8
rucDJNi+GrLat4wNza4t3FKf3rBenBFzii14OEUTE0JgpY90fGUF3n/i0duaB/k=
=90Ns
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.8-20160617' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 14 patches for net-next/master.
Geert Uytterhoeven contributes a patch that adds a file patterns for
CAN device tree bindings to MAINTAINERS. A patch by Alexander Aring
fixes warnings when building without proc support. A patch by me
improves the sample point calculation. Marek Vasut's patch converts
the slcan driver to use CAN_MTU. A patch by William Breathitt Gray
converts the tscan1 driver to use module_isa_driver.
Two patches by Maximilian Schneider for the gs_usb driver fix coding
style and add support for set_phys_id callback. 5 patches by Oliver
Hartkopp add support for CANFD to the bcm. And finally two patches
by Ramesh Shanmugasundaram, which add support for the rcar_canfd
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: e577516b9d ("mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason in rx_descs property because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels.
That is, if number of descriptors 256, 128 of them are for rx
channels. While receiving, the descriptor is freed to the pool and
then allocated with new skb. And if in DT the "rx_descs" is set to
64, then 128 - 64 = 64 descriptors are always in the pool and cannot
be used, for tx, for instance. It's not correct resource usage,
better to set it to half of pool, then the rx pool can be used in
full. It will not have any impact on performance, as anyway, the
"redundant" descriptors were unused.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 source address selection needs to consider the real egress route.
Similar to IPv4 implement a get_saddr6 method which is called if
source address has not been set. The get_saddr6 method does a full
lookup which means pulling a route from the VRF FIB table and properly
considering linklocal/multicast destination addresses. Lookup failures
(eg., unreachable) then cause the source address selection to fail
which gets propagated back to the caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable i was declared but was never used and we were getting a
build warning for that.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact is VXLAN with Generic Protocol Extensions cannot be supported by
the same hardware parsers that support VXLAN. The protocol extensions
allow for things like a Next Protocol field which in turn allows for things
other than Ethernet to be passed over the tunnel. Most existing parsers
will not know how to interpret this.
To resolve this I am giving VXLAN-GPE its own UDP encapsulation offload
type. This way hardware that does support GPE can simply add this type to
the switch statement for VXLAN, and if they don't support it then this will
fix any issues where headers might be interpreted incorrectly.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
The last change is that I pulled the rtnl_lock/unlock into the conditional
statement for IXGBE_FLAG2_VXLAN_REREG_NEEDED. The motivation behind this
is to avoid unneeded bouncing of the mutex which will just slow down the
handling of this call anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
I have also gone though and removed the BE2NET_VXLAN config option since it
no longer relies on the VXLAN code anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port number for GENEVE is hard coded into the bnxt driver. This is the
kind of thing we want to avoid going forward. For now I will integrate
this back into the port notifier so that we can change the GENEVE port
number if we need to in the future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ends up doing several things. First it updates the driver to
make use of the new unified UDP tunnel offload notifier functions. In
addition I updated the code so that we can work around the bits that were
checking for if VXLAN was enabled since we are now using a notifier based
setup.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
I also went through and dropped the BNX2X VXLAN and GENEVE specific build
flags.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch merges the notifiers for VXLAN and GENEVE into a single UDP
tunnel notifier. The idea is that we will want to only have to make one
notifier call to receive the list of ports for VXLAN and GENEVE tunnels
that need to be offloaded.
In addition we add a new set of ndo functions named ndo_udp_tunnel_add and
ndo_udp_tunnel_del that are meant to allow us to track the tunnel meta-data
such as port and address family as tunnels are added and removed. The
tunnel meta-data is now transported in a structure named udp_tunnel_info
which for now carries the type, address family, and port number. In the
future this could be updated so that we can include a tuple of values
including things such as the destination IP address and other fields.
I also ended up going with a naming scheme that consisted of using the
prefix udp_tunnel on function names. I applied this to the notifier and
ndo ops as well so that it hopefully points to the fact that these are
primarily used in the udp_tunnel functions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch merges the GENEVE and VXLAN code so that both functions pass
through a shared code path. This way we can start the effort of using a
single function on the network device drivers to handle both of these
tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we add udp_tunnel.h to vxlan.h and geneve.h
header files. This is useful as I plan to move the generic handlers for
the port offloads into the udp_tunnel header file and leave the vxlan and
geneve headers to be a bit more protocol specific.
I also went through and cleaned out a number of redundant includes that
where in the .h and .c files for these drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clubs the Renesas controller drivers in one rcar dir.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the CAN FD controller found in Renesas R-Car
SoCs. The controller operates in CAN FD only mode by default.
CAN FD mode supports both Classical CAN & CAN FD frame formats. The
controller supports ISO 11898-1:2015 CAN FD format only.
This controller supports two channels and the driver can enable either
or both of the channels.
Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one
per channel) for transmission. Rx filter rules are configured to the
minimum (one per channel) and it accepts Standard, Extended, Data &
Remote Frame combinations.
Note: There are few documentation errors in R-Car Gen3 Hardware User
Manual v0.5E with respect to CAN FD controller. They are listed below:
1. CAN FD interrupt numbers 29 & 30 are listed as per channel
interrupts. However, they are common to both channels (i.e.) they are
global and channel interrupts respectively.
2. CANFD clock is derived from PLL1. This is not documented.
3. CANFD clock is further divided by (1/2) within the CAN FD controller.
This is not documented.
4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It
is specified 4 Tq in the manual.
5. The maximum number of message RAM area the controller can use is 3584
bytes. It is specified 10752 bytes in the manual.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch Implements the ethtool set_phys_id callback to ease the
locating of specific physical devices. Currently only supported on
candleLight interfaces.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
[mkl: split codingstyle change sinto separate patch]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts "1 << n" by BIT(n) and fixes the indention. No
functional change.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
[mkl: split codingstyle changes into separate patch]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use CAN_MTU macro instead of sizeof(struct can_frame) just like the
other drivers do.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch optimizes the calculation of the sample point. To understand what it
does have a look at the original implementation.
If there is a combination of timing parameters where both the bitrate and
sample point error are 0 the current implementation will find it.
However if the reference clock doesn't allow an optimal bitrate (this means the
bitrate error is always != 0) there might be several timing parameter
combinations having the same bitrate error. The original implementation will
allways choose the one with the highest brp. The actual sample point error
isn't taken into account.
This patch changes the algorithm to minimize the sample point error, too. Now a
brp/tseg combination is accepted as better if one of these condition are
fulfilled:
1) the bit rate error must be smaller, or
2) the bit rate error must be equal and
the sample point error must be equal or smaller
If a smaller bit rate error is found the sample point error is reset. This
ensures that we first optimize for small bit rate error and then for small
sample point errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With all vmxnet3 version 3 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 3, provided
the emulation advertises support for version 3.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vmxnet3 version 3, the emulation added support for the vmxnet3 driver
to communicate information about the memory regions the driver will use
for rx/tx buffers. The driver can also indicate which rx/tx queue the
memory region is applicable for. If this information is communicated
to the emulation, the emulation will always keep these memory regions
mapped, thereby avoiding the mapping/unmapping overhead for every packet.
Currently, Linux vmxnet3 driver does not leverage this capability. The
feasibility of using this approach for the Linux vmxnet3 driver will be
investigated independently and if possible, will be part of a different
patch. This patch only exposes the emulation capability to the driver
(vmxnet3_defs.h is identical between the driver and the emulation).
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The emulation supports a variety of coalescing modes viz. disabled
(no coalescing), adaptive, static (number of packets to batch before
raising an interrupt), rate based (number of interrupts per second).
This patch implements get_coalesce and set_coalesce methods to allow
querying and configuring different coalescing modes.
Signed-off-by: Keyong Sun <sunk@vmware.com>
Signed-off-by: Manoj Tammali <tammalim@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 driver preallocates buffers for receiving packets and posts the
buffers to the emulation. In order to deliver a received packet to the
guest, the emulation must map buffer(s) and copy the packet into it.
To avoid this memory mapping overhead, this patch introduces the receive
data ring - a set of small sized buffers that are always mapped by
the emulation. If a packet fits into the receive data ring buffer, the
emulation delivers the packet via the receive data ring (which must be
copied by the guest driver), or else the usual receive path is used.
Receive Data Ring buffer length is configurable via ethtool -G ethX rx-mini
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 driver supports transmit data ring viz. a set of fixed size
buffers used by the driver to copy packet headers. Small packets that
fit these buffers are copied into these buffers entirely.
Currently this buffer size of fixed at 128 bytes. This patch extends
transmit data ring implementation to allow variable length transmit
data ring buffers. The length of the buffer is read from the emulation
during initialization.
Signed-off-by: Sriram Rangarajan <rangarajans@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shared memory is used to exchange information between the vmxnet3 driver
and the emulation. In order to request emulation to perform a task, the
driver first populates specific fields in this shared memory and then
issues corresponding command by writing to the command register(CMD). The
layout of the shared memory was defined by vmxnet3 version 1 and cannot
be extended for every new command without breaking backward compatibility.
To address this problem, in vmxnet3 version 3, the emulation repurposed
a reserved field in the shared memory to represent command information
instead. For new commands, the driver first populates the command
information field in the shared memory and then issues the command. The
emulation interprets the data written to the command information depending
on the type of the command. This patch exposes this capability to the driver.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 is currently at version 2, but some command definitions from
previous vmxnet3 versions are missing. Add those definitions before
moving to version 3.
Also, introduce utility macros for vmxnet3 version comparison and update
Copyright information and Maintained by.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/ethernet/freescale/gianfar.c:2278:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/hamradio/baycom_par.c:159:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
For consistency with other drivers, I'm changing '__inline__' to 'inline'
at the same time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using an incorrect define to get the irq vector number.
NFP_NET_CFG_LSC is a control BAR offset, LSC interrupt vector
index is called NFP_NET_IRQ_LSC_IDX. For machines with less
than 30 CPUs this meant that we were disabling/enabling IRQ 0.
For bigger hosts we were just playing with the 31st RX/TX
interrupt.
Fixes: 0ba40af963 ("nfp: move link state interrupt request/free calls")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for tlan_handle_tx_eoc when building with "make W=1"
drivers/net/ethernet/ti/tlan.c: In function 'tlan_handle_tx_eoc':
drivers/net/ethernet/ti/tlan.c:1647:59: error: parameter 'host_int' set but not used [-Werror=unused-but-set-parameter]
static u32 tlan_handle_tx_eoc(struct net_device *dev, u16 host_int)
This is harmless, but removing the unused assignment lets us avoid
the warning with no downside.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for qlcnic_83xx_get_mac_address when building with
"make W=1":
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c: In function 'qlcnic_83xx_get_mac_address':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:2156:8: error: parameter 'function' set but not used [-Werror=unused-but-set-parameter]
Clearly this is harmless, but there is also no point for setting
the variable, so we can simply remove the assignment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53 dsa register access confusingly uses __raw register accessors
when both the CPU and the device are big-endian, but it uses little-
endian accessors when the same device is used from a little-endian
CPU, which makes no sense.
This uses normal accessors in device-endianess all the time, which
will work in all four combinations of register and CPU endianess,
and it will have the same barrier semantics in all cases.
This also seems to take care of a (false positive) warning I'm getting:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:109:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
I originally planned to submit another patch for that warning
and did this one as a preparation cleanup, but it does seem to be
sufficient by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In set_speed(), BMCR_RESET would be set when the flag of PHY_RESET
is set. Use BMCR_RESET to replace testing the flag of PHY_RESET.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4e driver does not support more than one port for VXLAN offload. As
such expecting the hardware to offload other ports is invalid since it
appears the parsing logic is used to perform Tx checksum and segmentation
offloads. Use the vxlan_port number to determine in which cases we can
apply the offload and in which cases we can not.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When suspending the machine, do not shutdown the external PHY by cutting
its regulator in the mac platform driver suspend code if Wake-on-Lan is enabled,
else it cannot wake us up.
In order to do this, split the suspend/resume callbacks from the
init/exit callbacks, so we can condition the power-down on the lack of
need to wake-up from the LAN but do it unconditionally when unloading the
module.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this including cfg80211.h in a wrong order could result in:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:122:24: error: array type has incomplete element type
struct brcmf_wsec_key key[BRCMF_MAX_DEFAULT_KEYS];
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:291:24: error: field ‘p2p’ has incomplete type
struct brcmf_p2p_info p2p;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:297:27: error: field ‘pmk_list’ has incomplete type
struct brcmf_pmk_list_le pmk_list;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:317:28: error: field ‘assoclist’ has incomplete type
struct brcmf_assoclist_le assoclist;
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This attribute was added 3 years ago by
commit 3eacf86655 ("brcmfmac: introduce brcmf_cfg80211_vif structure")
but it remains unused since then. It seems we can safely drop it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per Michael Büsch: "All a-phy code is usused", so remove it all.
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports the following error with -Werror=unused-const-variable.
drivers/net/wireless/broadcom/b43/phy_a.c:576:40: error:
'b43_phyops_a' defined but not used
Per Michael Büsch: "All a-phy code is usused", so remove it all,
and move the remaining Type-G initialization code into phy_g.c.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
In if_sdio.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_sdio_host_to_card_worker.
The workitem is involved in sending packets to firmware.
Forward progress under memory pressure is a requirement here.
In if_spi.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_spi_host_to_card_worker.
The workitem is involved in sending command packets from the host.
Forward progress under memory pressure is a requirement here.
Dedicated workqueues have been used in both cases since the workitems
on the workqueues are involved in normal device operation with
WQ_MEM_RECLAIM set to gurantee forward progress under memory pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the calls to flush_workqueue() before
destroy_workqueue() have been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus rx sequence is not in order because that control and event
frames always cause immediate send, but data frames may be held
for glomming in firmware side. It is not actually an error as the
packets are still processed even if the RX sequence is not in order.
Therefor the error message is rephrased and changed to a debug
message.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for the new PCIE devices 43525 and 43465.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using nmap tool with FMAC, the nmap packets were be dropped by kernel
because the size was too short. The kernel message showed like
"nmap: packet size is too short (42 <= 50)". It is caused by the packet
length is shorter than ndev->hard_header_len. According to definition of
LL_RESERVED_SPACE() and hard_header_len, we should use hard_header_len
to reserve for L2 header, like ethernet header(ETH_HLEN) in our case and
use needed_headroom for the additional headroom needed by hardware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error message is given for something that is not an error here as
the drive strength configuration may not be applicable for specific
devices. Therefor the error message is rephrased and changed to a
debug message.
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
[arend@broadcom.com: rephrase commit message]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SKBs can come with a prioriy. Currently a priority of 0..7 is
assumed. But this assumption is incorrect. To fix this any
priority of 0 or higher then 7 will be adjusted by calling
cfg80211_classify8021d
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only hardcode the LED behavior if the SROM doesn't provide any for all
LEDs of the card. This avoids instantiating LED triggers for unconnected
LEDs, while (hopefully) keeping things working for old cards with a
blank SROM.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports:
drivers/net/wireless/marvell/libertas_tf/main.c:30:19: error:
'lbtf_driver_version' defined but not used
with -Werror=unused-const-variable=.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are nine copies of the _rtl88ee_read_adapter_info() function,
and most but not all of them cause a build warning in some configurations:
rtl8192de/hw.c: In function '_rtl92de_read_adapter_info':
rtl8192de/hw.c:1767:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
rtl8723ae/hw.c: In function '_rtl8723e_read_adapter_info.constprop':
rtlwifi/rtl8723ae/hw.c:1654:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that when rtlefuse->epromtype is something other than
EEPROM_BOOT_EFUSE, the rest of the function uses undefined data, resulting
in random behavior later.
Apparently, in some drivers, the problem was already found and fixed
but the fix did not make it into the others.
This picks one approach to deal with the problem and applies identical
code to all 9 files, to simplify the later consolidation of those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two firmware events we handle similarly in brcmfmac:
BRCMF_E_LINK and BRCMF_E_IF. The difference from firmware point of view
is that the first one means BSS remains present in the firmware. Trying
to (re)create it (e.g. when adding new virtual interface) will result in
an error.
Current code treats both events in a similar way. It removes Linux
interface for each of them. It works OK with e.g. BCM43602. Its firmware
generates both events for each interface. It means we get BRCMF_E_LINK
and remove interface. That is soon followed by BRCMF_E_IF which means
BSS was also removed in a firmware. The only downside of this is a
harmless error like:
[ 208.643180] brcmfmac: brcmf_fweh_call_event_handler: no interface object
Unfortunately BCM4366 firmware doesn't automatically remove BSS and so
it doesn't generate BRCMF_E_IF. In such case we incorrectly remove Linux
interface on BRCMF_E_LINK as BSS is still present in the firmware. It
results in an error when trying to re-create virtual interface, e.g.:
> iw phy phy1 interface add wlan1-1 type __ap
[ 3602.929199] brcmfmac: brcmf_ap_add_vif: timeout occurred
command failed: I/O error (-5)
With this patch we don't remove Linux interface while firmware keeps
BSS. Thanks to this we keep a consistent states of host driver and
device firmware.
Further improvement should be to mark BSS as disabled and remove
interface on BRCMF_E_LINK. Then we should add support for reusing
BSS-es.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware for new chipsets is based on a new major version of code
internally maintained at Broadcom. E.g. brcmfmac4366b-pcie.bin (used for
BCM4366B1) is based on 10.10.69.3309 while brcmfmac43602-pcie.ap.bin was
based on 7.35.177.56.
Currently setting AP 5 GHz channel doesn't work reliably with BCM4366B1.
When setting e.g. 36 control channel with VHT80 (center channel 42)
firmware may randomly pick one of:
1) 52 control channel with 58 as center one
2) 100 control channel with 106 as center one
3) 116 control channel with 122 as center one
4) 149 control channel with 155 as center one
It seems new firmwares require setting AP mode (BRCMF_C_SET_AP) before
specifying a channel. Changing an order of firmware calls fixes the
problem. This requirement resulted in two separated "chanspec" calls,
one in AP code path and one in P2P path.
This fix was verified with BCM4366B1 and tested for regressions on
BCM43602.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 on x86 started warning about wl3501_get_encode when building
with -O2:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_get_encode’:
drivers/net/wireless/wl3501_cs.c:1769:5: warning: ‘implemented’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1686:19: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1702:20: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1719:23: warning: ‘txpow’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1752:20: warning: ‘retry’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1806:25: warning: ‘pwr_state’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1383:24: warning: ‘value’ may be used uninitialized in this function
I could not figure out what exactly confuses gcc here, but splitting the
wl3501_get_mib_value function into two helps the compiler to figure out
that the variables are not actually used uninitialized, and makes it
slightly clearer to a human reader what the function actually does and
which parts of it are under the spinlock.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document lists the possible compatible strings that a SDIO child
node can have, so the driver checks if the defined in the node matches.
But the error message when that's not the case is misleading, so change
for one that makes clear what the error really is. Also, returning a -1
as errno code is not correct since that's -EPERM. A -EINVAL seems to be
a more appropriate one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document say that the "interrupts" property in the child node is
optional. So the property being missed shouldn't be treated as an error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function can fail so the returned value should be checked
and the error propagated to the caller in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's better to have the device name prefixed in the error message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of duplicating part of the cleanups needed in case of an error
in .probe callback, have a single error path and use goto labels as is
common practice in the kernel.
This also has the nice side effect that the cleanup operations are made
in the inverse order of their counterparts, which was not the case for
the mwifiex_add_card() error path.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's only a check if mwifiex_add_card() returned a nonzero value, but
the actual error code is neither stored nor propagated to the caller. So
instead of always returning -1 (which is -EPERM and not a suitable errno
code in this case), propagate the value returned by mwifiex_add_card().
Patch also removes the assignment of sdio_disable_func() returned value
since it was overwritten anyways and what matters is to know the error
value returned by the first function that failed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the sdio_enable_func() function fails on .probe, the -EIO errno code
is always returned but that could make more difficult to debug and find
the cause of why the function actually failed.
Since the driver/device core prints the value returned by .probe in its
error message propagate what was returned by sdio_enable_func() at fail.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is an auto enumerable bus so the SDIO devices are matched using the
sdio_device_id table and not using compatible strings from a OF id table.
However, commit ce4f6f0c35 ("mwifiex: add platform specific wakeup
interrupt support") allowed to match nodes defined as child of the SDIO
host controller in the probe function using a compatible string to setup
platform specific parameters in the DT.
The problem is that the OF parse function is always called regardless if
the SDIO dev has an OF node associated or not, and prints an error if it
is not found. So, on a platform that doesn't have a node for a SDIO dev,
the following misleading error message will be printed:
[ 12.480042] mwifiex_sdio mmc2:0001:1: sdio platform data not available
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is helpful for debugging. Without this all I was getting from "iw"
command on failed creating of P2P interface was:
> command failed: Too many open files in system (-23)
Signed-off-by: Rafal Milecki <zajec5@gmail.com>
[arend@broadcom.com: reduce error prints upon iface creation]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git fixes for 4.7. Major changes:
ath9k
* fix GPIO mask regression with AR9462 and AR9565
ath10k
* fix deadlock while processing rx_in_ord_ind
* fix crash related to printing firmware features in debug mode
* fix deadlock when peer cannot be created
path_b_ok is being assigned but immediately after path_a_ok is being
compared to the value 0x03. This appears to be a typo on the
variable name, compare path_b_ok instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rx early size should be
(agg_buf_sz - packet size) / 8
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If should be done after net_dev->hw_features initialization, to keep the
feature there to be able to enable it later using ethtool.
VLAN filtering is enforced and fixed if vPort requires usage of VLAN
filters to receive tagged traffic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports HW VLAN filtering, en/disabled using ethtool.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it contains dummy VLAN entry with unspecified VID only.
The entry is used for the case when HW VLAN filtering is not used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
