pcie_poll_cmd() take msecs instead of jiffies, so convert timeout to msecs.
Fixes: 40b960831c ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Powering off a hot-pluggable device, e.g., with pci_set_power_state(D3cold),
normally generates a hot-remove event that unbinds the driver.
Some drivers expect to remain bound to a device even while they power it
off and back on again. This can be dangerous, because if the device is
removed or replaced while it is powered off, the driver doesn't know that
anything changed. But some drivers accept that risk.
Add pci_ignore_hotplug() for use by drivers that know their device cannot
be removed. Using pci_ignore_hotplug() tells the PCI core that hot-plug
events for the device should be ignored.
The radeon and nouveau drivers use this to switch between a low-power,
integrated GPU and a higher-power, higher-performance discrete GPU. They
power off the unused GPU, but they want to remain bound to it.
This is a reimplementation of f244d8b623 ("ACPIPHP / radeon / nouveau:
Fix VGA switcheroo problem related to hotplug") but extends it to work with
both acpiphp and pciehp.
This fixes a problem where systems with dual GPUs using the radeon drivers
become unusable, freezing every few seconds (see bugzillas below). The
resume of the radeon device may also fail, e.g.,
This fixes problems on dual GPU systems where the radeon driver becomes
unusable because of problems while suspending the device, as in bug 79701:
[drm] radeon: finishing device.
radeon 0000:01:00.0: Userspace still has active objects !
radeon 0000:01:00.0: ffff8800cb4ec288 ffff8800cb4ec000 16384 4294967297 force free
...
WARNING: CPU: 0 PID: 67 at /home/apw/COD/linux/drivers/gpu/drm/radeon/radeon_gart.c:234 radeon_gart_unbind+0xd2/0xe0 [radeon]()
trying to unbind memory from uninitialized GART !
or while resuming it, as in bug 77261:
radeon 0000:01:00.0: ring 0 stalled for more than 10158msec
radeon 0000:01:00.0: GPU lockup ...
radeon 0000:01:00.0: GPU pci config reset
pciehp 0000:00:01.0:pcie04: Card not present on Slot(1-1)
radeon 0000:01:00.0: GPU reset succeeded, trying to resume
*ERROR* radeon: dpm resume failed
radeon 0000:01:00.0: Wait for MC idle timedout !
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77261
Link: https://bugzilla.kernel.org/show_bug.cgi?id=79701
Reported-by: Shawn Starr <shawn.starr@rogers.com>
Reported-by: Jose P. <lbdkmjdf@sharklasers.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rajat Jain <rajatxjain@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
CC: stable@vger.kernel.org # v3.15+
During PCIe hot-plug initialization - pciehp_probe() - data structures
related to slot capabilities are set up. As part of this set up, ISRs are
put in place to handle slot events and all event bits are cleared out.
This patch adds the Data Link Layer State Changed (PCI_EXP_SLTSTA_DLLSC)
Slot Status bit to the event bits that are cleared out during
initialization.
If the BIOS doesn't clear DLLSC before handoff to the OS, pciehp notices
that it's set and interprets it as a new Link Up event, which results in
spurious messages:
pciehp 0000:82:04.0:pcie24: slot(4): Link Up event
pciehp 0000:82:04.0:pcie24: Device 0000:83:00.0 already exists at 0000:83:00, cannot hot-add
pciehp 0000:82:04.0:pcie24: Cannot add device at 0000:83:00
Prior to e48f1b67f6 ("PCI: pciehp: Use link change notifications for
hot-plug and removal"), pciehp ignored DLLSC.
Reference:
PCI-SIG. PCI Express Base Specification Revision 4.0 Version 0.3
(PCI-SIG, 2014): 7.8.11. Slot Status Register (Offset 1Ah).
[bhelgaas: add e48f1b67f6 ref and stable tag]
Fixes: e48f1b67f6 ("PCI: pciehp: Use link change notifications for hot-plug and removal")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=79611
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
"no_cmd_complete" is only used once, and it duplicates read-only
information we already have in the cached Slot Capabilities value.
Remove the field and use the existing macro NO_CMD_CMPL() instead.
[bhelgaas: changelog]
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We use incorrect logic to decide whether a PCIe hotplug controller
generates command completion events.
5808639bfa ("pciehp: fix slow probing") assumed that the Slot Status
"Command Completed" bit was set only for commands affecting slot power,
indicators, or electromechanical interlock. That assumption is false: per
sec. 6.7.3.2 of PCIe spec r3.0, a write targeting any portion of the Slot
Control register is a command, and (if command completed events are
supported) software must wait for a command to complete before issuing the
next command.
5808639bfa was to fix boot-time timeouts (see bugzilla below) on a Lenovo
Thinkpad R61 with an Intel hotplug controller. The controller probably has
the Intel CF118 erratum, which means it doesn't report Command Completed
unless the Slot Control power, indicator, or interlock bits are changed.
This causes a timeout because pciehp always waits for Command Complete (if
supported), regardless of which bits are changed.
Remove the incorrect logic because the timeouts have been addressed
differently by these changes:
PCI: pciehp: Wait for hotplug command completion lazily
PCI: pciehp: Compute timeout from hotplug command start time
Link: https://bugzilla.kernel.org/show_bug.cgi?id=10751
Tested-by: Rajat Jain <rajatxjain@gmail.com> (IDT 807a controller)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
If we issue a hotplug command, go do something else, then come back and
wait for the command to complete, we don't have to wait the whole timeout
period, because some of it elapsed while we were doing something else.
Keep track of the time we issued the command, and wait only until the
timeout period from that point has elapsed.
For controllers with errata like Intel CF118, we previously timed out
before issuing the second hotplug command:
At time T1 (during boot):
- Write DLLSCE, ABPE, PDCE, etc. to Slot Control
At time T2 (hotplug event):
- Wait for command completion (CC) in Slot Status
- Timeout at T2 + 1 second because CC is never set in Slot Status
- Write PCC, PIC, etc. to Slot Control
With this change, we wait until T1 + 1 second instead of T2 + 1 second.
If the hotplug event is more than 1 second after the boot-time
initialization, we won't wait for the timeout at all.
We still emit a "Timeout on hotplug command" message if it timed out; we
should see this on the first hotplug event on every controller with this
erratum, as well as on real errors on controllers without the erratum.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Tested-by: Rajat Jain <rajatxjain@gmail.com> (IDT 807a controller)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Previously we issued a hotplug command and waited for it to complete. But
there's no need to wait until we're ready to issue the *next* command. The
next command will probably be much later, so the first one may have already
completed and we may not have to actually wait at all.
Because of hardware errata, some controllers generate command completion
events for some commands but not others. In the case of Intel CF118 (see
spec update reference), the controller indicates command completion only
for Slot Control writes that change the value of the following bits:
Power Controller Control
Power Indicator Control
Attention Indicator Control
Electromechanical Interlock Control
Changes to other bits, e.g., the interrupt enable bits, do not cause the
Command Completed bit to be set. Controllers from AMD and Nvidia are
reported to have similar errata.
These errata cause timeouts when pcie_enable_notification() enables
interrupts. Previously that timeout occurred at boot-time. With this
change, the timeout occurs later, when we change the state of the slot
power, indicators, or interlock. This speeds up boot but causes a timeout
at the first hotplug event on the slot. Subsequent events don't timeout
because only the first (boot-time) hotplug command updates Slot Control
without touching the power/indicator/interlock controls.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Tested-by: Rajat Jain <rajatxjain@gmail.com> (IDT 807a controller)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
pcie_wait_cmd() waits for the controller to finish a hotplug command. Move
the associated logic (to determine whether waiting is required and whether
we're using interrupts or polling) from pcie_write_cmd() to
pcie_wait_cmd().
No functional change.
Tested-by: Rajat Jain <rajatxjain@gmail.com> (IDT 807a controller)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.
No functional change.
[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix various whitespace errors.
No functional change.
[bhelgaas: fix other similar problems]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of a spurious "cmd completed", pcie_write_cmd() does not clear it,
but yet expects more "cmd completed" events to be generated. This does not
happen because the previous (spurious) event has not been acknowledged.
Fix that.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case a card is physically yanked out, it should immediately be removed,
regardless of the "surprise" capability bit. Thus:
- Always handle the physical removal - regardless of the "surprise" bit.
- Don't use "surprise" capability when making decisions about enabling
presence detect notifications.
- Reword the comments to indicate the intent.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Today it is there is no protection around pciehp_enable_slot() and
pciehp_disable_slot() to ensure that they complete before another
hot-plug operation can be done on that particular slot.
This patch introduces the slot->hotplug_lock to ensure that any hotplug
operations (add / remove) complete before another hotplug event can begin
processing on that particular slot.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Disable the link notification (in addition to presence detect
notifications) across the slot reset since the reset could flap the link,
and we don't want to treat it as hot unplug followed by a hotplug.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need future link up events for hot-add, thus don't disable the link
permanently during device removal. Also, remove the static functions that
are now left unused.
This reverts part of 2debd92899 ("PCI: pciehp: Disable/enable link during
slot power off/on"). This was discussed at the URL below, where it was
revealed that it was done for a bug in a PCIe repeater chip on that
particular platform.
Link: https://lkml.kernel.org/r/CAErSpo72KZ-a2OSQLWoK71GCgwBt676XZdGt4tEYm-6UYnLmPw@mail.gmail.com
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enable the Link state notifications unconditionally. Enable the
presence detection notification only if attention button is absent.
This was discussed at this thread:
https://lkml.kernel.org/r/529E5C0E.80903@gmail.com
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A lot of systems do not have the fancy buttons and LEDs, and instead
want to rely only on the Link state change events to drive the hotplug
and removal state machinery.
(http://www.spinics.net/lists/hotplug/msg05802.html)
This patch adds support for that functionality. Here are the details
about the patch itself:
* Define and use interrupt events for linkup / linkdown.
* Make the pcie_isr() also look at link events, and direct control to
corresponding (new) link state change handler function.
* Introduce the functions to handle link-up and link-down events and
queue the add / removal work in the slot->wq to be processed by
pciehp_power_thread()
As a side note, this patch also fixes the bug
https://bugzilla.kernel.org/show_bug.cgi?id=65521 "pciehp ignores Data Link
Layer State Changed bit."
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
check_link_active() functionality needs to be used by subsequent patches
(that introduce link state change based hotplug). Thus make the function
non-static, and rename it to pciehp_check_link_active() so as to be
consistent with other non-static functions.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, the caller checked ATTN_LED() or PWR_LED() to see whether the
slot has indicators before setting the indicator state. That clutters the
caller unnecessarily, so this moves the test inside the callees. The test
may not even be necessary; per spec it should be harmless to try to turn on
a non-existent LED. But checking first does avoid unnecessary hotplug
commands.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add symbolic constants for the PCIe Slot Control indicator and power
control fields defined by spec and use them instead of open-coded hex
constants.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's simpler to test the PCI_EXP_SLTSTA_PFD bit directly and to write the
constant back to PCI_EXP_SLTSTA.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already have the vendor/device IDs from pci_setup_device(), so drop that
info and print things that will be more useful for debugging: the slot
number and presence of button/indicators/link active reporting/etc.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These functions:
pcie_enable_notification()
pciehp_power_off_slot()
pciehp_get_power_status()
pciehp_get_attention_status()
pciehp_set_attention_status()
pciehp_get_latch_status()
pciehp_get_adapter_status()
pcie_write_cmd()
now always return success, so this patch makes them void and drops the
error-checking code in their callers.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There's not much point in checking the return value from every config space
access because the only likely errors are design-time things like unaligned
accesses or invalid register numbers. The checking clutters the code
significantly, so this patch removes it.
No functional change.
Reference: http://lkml.kernel.org/r/CA+55aFzP4xEbcNmZ+MS0SQ3LrULzSq+dBiT_X9U-bPpR-Ukgrw@mail.gmail.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pciehp_readw() and pciehp_writew() wrappers only look up the pci_dev
and call the PCIe Capability accessors, so we can make things a little
more straightforward by just using the PCIe Capability accessors directly.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCIe hotplug has a bus per slot, so we can just use a normal
secondary bus reset. However, if a slot supports surprise removal,
a bus reset can be seen as a presence detection change triggering
a hot-remove followed by a hot-add. Disable presence detection from
triggering an interrupt or being polled around the bus reset.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For the workqueue creation interfaces that do not expect format strings,
make sure they cannot accidently be parsed that way. Additionally, clean
up calls made with a single parameter that would be handled as a format
string. Many callers are passing potentially dynamic string content, so
use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we have a hotplug-capable PCIe port with a second hotplug-capable
PCIe port below it, removing the device below the upstream port causes
a deadlock.
The deadlock happens because we use the pciehp_wq workqueue to run
pciehp_power_thread(), which uses pciehp_disable_slot() to remove devices
below the upstream port. When we remove the downstream PCIe port, we call
pciehp_remove(), the pciehp driver's .remove() method. That calls
flush_workqueue(pciehp_wq), which deadlocks because the
pciehp_power_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every PCIe port
and removing the single shared workqueue.
Here's the call path that leads to the deadlock:
pciehp_queue_pushbutton_work
queue_work(pciehp_wq) # queue pciehp_power_thread
...
pciehp_power_thread
pciehp_disable_slot
remove_board
pciehp_unconfigure_device
pci_stop_and_remove_bus_device
...
pciehp_remove # pciehp driver .remove method
pciehp_release_ctrl
pcie_cleanup_slot
flush_workqueue(pciehp_wq)
This is fairly urgent because it can be caused by simply unplugging a
Thunderbolt adapter, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2ssiRgcTD1bej2tkUUfsWmpL5eNtPcNif9va2-Gzb2u8nQ@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
On a system with a repeater on the system board to support gen2 hotplug,
we found that when an ExpressModule is removed from some slots,
/var/log/messages will be full of "card present/not present" warnings.
It turns out the root complex is continually trying to train the link to
the repeater because the repeater has not been reset.
This patch will disable the link at removal time to allow the repeater
to be reset properly. This also prevents a potential AER message at
removal time.
Also, when testing hotplug on a system under development, we found if we
boot the system without an EM installed, and later hot-add an EM, it
does not work with Linux, but another OS is ok. The root cause is that
BIOS left link disabled when slot was empty at boot time, and other OS
is modifying the link disable bit in link ctrl during power on/off.
So we should do the same thing to disable/enable link during power off/on.
-v2: check link DLLA bit instead of 100ms waiting.
Separate link disable/enable functions to another patch.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A few changes:
- remove the 'inline' and let the complier decide
- return a bool to indicate whether the link was active
- add a debug message to indicate link state when it beocmes active
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During reviewing
| PCI: pciehp: wait 1000 ms before Link Training check
Linus said:
>...
> That's a *long* time, and it's irritating to the user. It makes the
> user think "the machine is slow".
>...
> And quite frankly, an unconditional one-second delay here seems bad.
>Two seconds was unacceptable, one second is just bad.
Try to access the pci conf of a pci device that is supposed to show up
in 1s. If we can read back a valid vendor/device id, we can return
early.
Related discussion could be found:
https://lkml.org/lkml/2011/12/6/339
-v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device()
and reuse it from pciehp code. Suggested by Matthew Wilcox.
-v3: According to Kenj, don't use array in stack, and don't wait too long
for crs, also return fail status if not found.
Also separate pci_bus_dev_read_vendor_id() change to another patch.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in pciehp as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the port supports Link speeds greater than 5.0 GT/s, we must wait
for 100 ms after Link training completes before sending configuration
request.
Acked-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to wait for 1000 ms after Data Link Layer Link Active (DLLLA)
bit reads 1b before sending configuration request. Currently pciehp
does this wait after checking Link Training (LT) bit. But we need it
before checking LT bit because LT is still set even after DLLLA bit is
set on some platforms.
Acked-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During hot plug, board_added will call pciehp_power_on_slot().
But link speed is updated in pciehp_power_on_slot().
We should not update link speed there, because that is too early.
So move the link speed update to pciehp_check_link_status() after making
sure the link has been trained.
-v2: fix compile warning that Kenji found.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Naoki Yanagimoto reported that configuration read on some hot-added
PCIe device returns invalid value. This patch fixes this problem.
According to the PCIe spec, software must wait for at least 1 second
to judge if the hot-added device is broken after Data Link Layer State
Changed Event. This patch changes pciehp driver to wait for 1 second
after the Data Link Layer State Changed Event is detected before
initiating a configuration access instead of 100 ms.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Naoki Yanagimoto <yanagimoto@np.css.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both pciehp_wq and pciehp_ordered_wq upfront.
* Include workqueue.h from pciehp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
No functional change; just print resources in the conventional style.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the max_bus_speed and cur_bus_speed into the pci_bus. Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array. Use a single enum, and move it to
pci.h. Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Enabling power fault detected event notification in current pciehp
might cause power fault interrupt storm on some machines. On those
machines. On those machines, power fault detected bit in the slot
status register was set again immediately when it is cleared in the
interrupt service routine, and next power fault detected interrupt was
notified again. Therefore, disable power fault detected event
notification for now.
This patch also removes unnecessary handling for power fault cleared
event because this event is not supported by PCIe spec.
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in pciehp driver. This avoids unnecessary search in PCI
configuration space. This patch also removes 'cap_base' field in
struct controller, that was used to hold PCIe capability offset by
pciehp itself.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp returns successfully on read/write failure with dummy
state values. It should return error instead.
With this patch, pciehp no longer uses hotplug_slot_info data
structure. So this also removes hotplug_slot_info related code. But
note that it still allocates hotplug_slot_info because it is required
by pci hotplug core.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
