Add support for BCM957504 with device ID 1751
Signed-off-by: Erik Burrows <erik.burrows@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit below has introduced a bug in netcp driver that causes
the ethss driver probe failure and thus break the networking function
on K2 SoCs such as K2HK, K2L, K2E etc. This patch fixes the issue to
restore networking on the above SoCs.
Fixes: 21c328dcec ("net: ethernet: Convert to using %pOFn instead of device_node.name")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing device reference release-after-use in
the positive leg of the roce reset API of the HNS DSAF.
Fixes: c969c6e7ab ("net: hns: Fix object reference leaks in hns_dsaf_roce_reset()")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are saving the status of EEE even before we try to enable it. This
leads to a race with XMIT function that tries to arm EEE timer before we
set it up.
Fix this by only saving the EEE parameters after all operations are
performed with success.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 forwards all syn packets to the driver without validating the mac
address. Add validation check in the driver's iWARP listener flow and drop
the packet if it isn't intended for the device.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumption that the maximum size of a syn packet is 128 bytes
is wrong. Tunneling headers were not accounted for.
Allocate buffers large enough for mtu.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c: In function 'bnx2x_get_hwinfo':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:11940:10: warning:
variable 'mfw_vn' set but not used [-Wunused-but-set-variable]
It's never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning:
drivers/net/ethernet/cavium/liquidio/cn23xx_pf_device.c:1453:35: warning: Using plain integer as NULL pointer
drivers/net/ethernet/cavium/liquidio/lio_main.c:2910:23: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.
This patch was recently reverted due to a dependency with another
problematic patch. But because it didn't contribute to the problem
it was rebased and can be resubmitted.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP2ME packet trap is triggered by packets hitting local routes.
After evaluating current defaults used by the driver it was decided to
reduce the amount of traffic generated by this trap to 1Kpps and
increase the burst size. This is inline with similarly deployed systems.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a en_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2431:5: warning:
symbol 'hclge_set_all_vf_rst' was not declared. Should it be static?
Fixes: aa5c4f175b ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function meth_init_tx_ring() is called from meth_tx_timeout(),
in which spin_lock is held, so we should use GFP_ATOMIC instead.
Fixes: 8d4c28fbc2 ("meth: pass struct device to DMA API functions")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mv643xx_eth_shared_of_probe() fails, mv643xx_eth_shared_probe()
leaves clk enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC IP is little-endian and used on several kind of CPU (big or little
endian). Main callbacks functions of the stmmac drivers take care about
it. It was not the case for dwmac4_get_timestamp function.
Fixes: ba1ffd74df ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check mask fields of tcp and ip flags when setting the corresponding mask
flag used in hardware.
Fixes: 8f2566225a ("flow_offload: add flow_rule and flow_match")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink now allows updating device flash. Implement this
callback.
Compared to ethtool update we no longer have to release
the networking locks - devlink doesn't take them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated thermal zone for each QSFP/SFP module. The current
temperature is obtained from the module's temperature sensor and the
trip points are set based on the warning and critical thresholds
read from the module.
A cooling device (fan) is bound to all the thermal zones. The
thermal zone governor is set to user space in order to avoid
collisions between thermal zones.
For example, one thermal zone might want to increase the speed of
the fan, whereas another one would like to decrease it.
Deferring this decision to user space allows the user to the take
the most suitable decision.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function-local variable "delay" enters the loop interpreted as delay
in bits. However, inside the loop it gets overwritten by the result of
mlxsw_sp_pg_buf_delay_get(), and thus leaves the loop as quantity in
cells. Thus on second and further loop iterations, the headroom for a
given priority is configured with a wrong size.
Fix by introducing a loop-local variable, delay_cells. Rename thres to
thres_cells for consistency.
Fixes: f417f04da5 ("mlxsw: spectrum: Refactor port buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) numerous libbpf API improvements, from Andrii, Andrey, Yonghong.
2) test all bpf progs in alu32 mode, from Jiong.
3) skb->sk access and bpf_sk_fullsock(), bpf_tcp_sock() helpers, from Martin.
4) support for IP encap in lwt bpf progs, from Peter.
5) remove XDP_QUERY_XSK_UMEM dead code, from Jan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In dwmac4_wrback_get_rx_timestamp_status we looking for a RX timestamp.
For that receive descriptors are handled and so we should use defines
related to receive descriptors. It'll no change the functional behavior
as RDES3_RDES1_VALID=TDES3_RS1V=BIT(26) but it makes code easier to read.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bodong Wang says,
BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:
- SEPARATED_HOST: ARM processors as a separated and orthogonal host
like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
external hosts virtualization model.
While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.
On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
traffic by default. It also should perform ENABLE_HCA for the host
PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
store various contexts for itself, the PF and VFs belong the
e-switch it manages.
The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.
The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcZ2amAAoJEEg/ir3gV/o+lzMIALvLNUoD6pXi41MWsOwvmAHg
07mzg1N80Z66MCcFau40I8T3h9NLiRMzNtFrBNtxx+ruwKFUpAjJHjaU0sms0yQH
WVjr35vk4XsZyDPSCJ4g/hCQVlgCT/1tIUvPO0YM9hjhDuVa9mT4wEpucQRDu8bO
KfeXNXLDFnlWxjokhpSVj369ozh+LTv4Kzy0MBBbji97bG6MktGAT8uCimUy7wG0
7dlYimnZ1+iUD1/DZQadiLCUHUu/rTcnvF2+DcdG/nbSU8ydVLgj6vgtIfCYt4e5
kcQO5hmatnl0iJUA8GNpdHQwGjYytKneoGmIfbMAK4KjvFNF+3/8N4Bytoa5kzk=
=DgTl
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Support Mellanox BlueField SmartNIC (mlx5-updates-2019-02-15)
Bodong Wang says,
BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:
- SEPARATED_HOST: ARM processors as a separated and orthogonal host
like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
external hosts virtualization model.
While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.
On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
traffic by default. It also should perform ENABLE_HCA for the host
PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
store various contexts for itself, the PF and VFs belong the
e-switch it manages.
The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.
The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT has its RXCHK parser block that attempts to validate the
packet structures, unfortunately setting the L2 header check bit will
cause Bridge PDUs (BPDUs) to be incorrectly rejected because they look
like LLC/SNAP packets with a non-IPv4 or non-IPv6 Ethernet Type.
Fixes: 4e8aedfe78c7 ("net: systemport: Turn on offloads by default")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in several dev_err messages, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the e-switch driver requires going to legacy mode before
changing to the offloads mode. This makes sense for regular case as
the legacy mode is done by creating VFs.
However, it's problematic when ECPF is the eswitch manager. In such
case, ECPF will control the vports on peer host including the peer
PF and VFs. But ECPF doesn't need and shall not create VFs as the
VFs are created in the peer PF host.
Grant ECPF the ability to change from none to the offloads mode. Note
that currently the only way to go back to none mode is by unloading
the ECPF driver.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When host PF changes the number of VFs, the ECPF esw driver will get
a FW event. It should query the number of VFs enabled by host PF and
update the VF reps accordingly. Note that host PF can't change the
number of VFs dynamically, it has to reset the number of VFs to 0
before changing to a new positive number.
The host event is registered when driver is moving to switchdev mode,
and it's the last step to do in esw_offloads_init. It's unregistered
and the work queue is flushed when driver quits from switchdev mode.
In this way, the host event and devlink command are serialized.
When driver is enabling switchdev mode, pay attention to the following
two facts:
1. Host PF must not have VF initialized as the flow table in ECPF has
ENCAP enabled as default. Such flow table can't be created with
existing initialized VFs.
2. ECPF doesn't know how many VFs the host PF will enable, ECPF
offloads flow steering shall create the flow table/groups based on
the max number of VFs possibly supported by host PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In offloads mode, the current implementation puts the uplink
representor at index zero of the vport reps array. It is not "natural"
to place it at index 0 since we want to put the representor for vport
0 at index 0 with the introduction of SmartNIC. A separate patch will
handle the case whether a rep is needed for vport 0 (PF vport).
So, we want to have a different placeholder for uplink vport and
representor. It was placed at the end of vport and rep array. Since
vport number can no longer act as an index into the vport or
representors arrays, use functions to map vport numbers to indices
when accessing the vports or representors arrays, and vice versa.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eswitch has two users: IB and ETH. They both register repersentors
when mlx5 interface is added, and unregister the repersentors when
mlx5 interface is removed. Ideally, each driver should only deal with
the entities which are unique to itself. However, current IB and ETH
drivers have to perform the following eswitch operations:
1. When registering, specify how many vports to register. This number
is the same for both drivers which is the total available vport
numbers.
2. When unregistering, specify the number of registered vports to do
unregister. Also, unload the repersentors which are already loaded.
It's unnecessary for eswitch driver to hands out the control of above
operations to individual driver users, as they're not unique to each
driver. Instead, such operations should be centralized to eswitch
driver. This consolidates eswitch control flow, and simplified IB and
ETH driver.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver loads and unloads all reps in an unbreakable
group. However, with ECPF, the reps of special vports such as uplink
and host PF should always be loaded in switchdev mode where the reps
for VFs will be loaded on-demand and unloaded on no-demand. This is
a pre-step for that change.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.
Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:
create: (none) -> unregistered
reg: unregistered -> registered
load: registered -> loaded
unload: loaded -> registered
unreg: registered -> unregistered
Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With only PF and VF, it is sufficient to have the vport/rep array
index as the vport number. This is because PF and VF vports numbers
are consecutive serial numbers. In downstream patches with
introducing of ECPF and UPLINK vports, it's not consecutive any more.
Use getter to get specific vport/rep, and use iterator to traversal
a list of vport/rep. This hides the translation between array index
and vport number, and provides flexibility of using different
translation mechanism in the future.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.
With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).
Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
E-switch offloads mode initialize/cleanup multiple steering related
entities (flow table/group). Refactor these operations to internal
helper functions for better block design.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commands referring to vports use the following scheme:
1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
referred vport and put 1 in other_vport. It was assumed that driver
is accessing other vport when vport number is greater than 0.
With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.
As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When bonding is added, driver assumes that it's RoCE LAG if no VF is
enabled. This is not enough for ECPF as the VF is enabled in host PF
side. LAG should only choose RoCE mode when both slave devices meet
conditions below:
1. E-Switch offloads mode is NONE.
2. No VF is enabled.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Merge mlx5-next shared branched into net-next,
From Bodong Wang:
1) Introduction of ECPF (Embedded CPU Physical Function), and low level
bits for mlx5 SmartNic capabilities support.
2) Vport enumeration refactoring that affect mlx5_ib and mlx5_core
From Aya Levin,
3) Add support for 50Gbps per lane link modes in the Port Type and Speed
register (PTYS)
4) Refactor low level query functions for PTYS register
5) Add support for 50Gbps per lane link modes to mlx5_ib
Note: due to a change in API in mlx5/core and a later patch from net-next,
a fixup was squashed with this merge commit that replaces FDB_UPLINK_VPORT
with MLX5_VPORT_UPLINK which exists only in upstream net-next.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the sge_host_page_size field to ULDs via cxgb4_lld_info, so that
iw_cxgb4 can make use of this in calculating the correct qp/cq mask.
Fixes: 2391b0030e ("cxgb4: Remove SGE_HOST_PAGE_SIZE dependency on page size")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Commit c9b47cc1fa ("xsk: fix bug when trying to use both copy and
zero-copy on one queue id") moved the umem query code to the AF_XDP
core, and therefore removed the need to query the netdevice for a
umem.
This patch removes XDP_QUERY_XSK_UMEM and all code that implement that
behavior, which is just dead code.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch exposes new link modes (including 50Gbps per lane), and ext_*
fields which describes the new link modes in Port Type and Speed
register (PTYS).
Access functions, translation functions (speed <-> HW bits) and
link max speed function were modified.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch fascicles queries to speed related fields in Port Type and
Speed register (PTYS) into a single API. I addition, this patch
refactors functions which serves only Ethernet driver: remove the
protocol type as an input parameter, move code from 'core' directory
into 'en' directory and add 'eth' prefix to the function's name. The
patch also encapsulates functions that are not used outside the Ethernet
driver removes redundant include files.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When dealing with the offloads mode initialization, driver refers to
the number of VFs and add magic number one (1) to take account of the
uplink. This is not clear and will make the code less readable after
adding other vports (e.g. host PF). As these are special vports
compared to VF vports, add a helper macro to denote such special
vports and eliminate the use of magic number.
Moreover, when creating offloads flow table and groups, the driver
reserves two more slots for UC and MC miss rules. Replace this magic
number with a helper macro as well.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
These are two macros in the driver general header which deal with the
number of total vports and if a vport is vport manager. Such macros
are vport entities, better to place them at the vport header file.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver used to name uplink vport as FDB_UPLINK_VPORT, it's hard to
comply with the same naming convention along with the introduction of
other vports. Use MLX5_VPORT as the prefix for such vports and
relocate the uplink vport definition to public header file for the
benefits of both net and IB drivers.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.
Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.
The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With the introduction of ECPF, we require that the ECPF driver will
aways call enable/disable HCA for that PF in the same way a PF does
this for its VFs. The PF is still responsible for calling enable and
disable HCA for its VFs.
To distinguish between the ECPF executing enable/disable HCA for
itself or for the PF, it sets the embedded CPU function bit in the
input params struct of these commands. When the bit is cleared and
function ID is zero, it refers to the peer PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.
With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.
When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.
The encoding before this patch was as follows:
function_id == 0: pages are requested for the function receiving
the EQE.
function_id != 0: pages are requested for VF identified by the
function_id value
A new one bit field in the EQE identifies that pages are requested for
the ECPF.
The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:
1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function
This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use u16 for vport number, which matches how hardware refers to this
argument throughout commands.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After failing to allocate a receive buffer the driver may fail to ever
request additional allocations. EF10 NICs require new receive buffers to
be pushed in batches of eight or more. The test for whether a slow fill
should be scheduled failed to take account of this. There is little
downside to *always* requesting a slow fill if we failed to allocate a
buffer, so the condition has been removed completely. The timer that
triggers the request for a refill has also been shortened.
Signed-off-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for FEC devices.
Use this field to store the register dump version exposed by the
kernel. The choosen version 2 corresponds to the kernel compile test:
#if defined(CONFIG_M523x) || defined(CONFIG_M527x)
|| defined(CONFIG_M528x) || defined(CONFIG_M520x)
|| defined(CONFIG_M532x) || defined(CONFIG_ARM)
|| defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)
and version 1 corresponds to the opposite. Binaries of ethtool unaware
of this version will dump the whole set as usual.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in intr_handler() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in arc_emac_tx_clean() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets/sets SGE Doorbell Queue timer ticks via ethtool
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 introduced a Timer Mechanism in SGE called the
SGE Doorbell Queue Timer. With this we can now configure
TX Queues to get CIDX Updates when:
Time(CIDX == PIDX) >= Timer
Previously we rely on TX Queue Status Page updates by hardware
for DMA completions. This will make Hardware/Firmware actually
deliver the CIDX Updates as Ingress Queue messages with
commensurate Interrupts.
So we now have a new RX Path component for processing CIDX Updates
and reclaiming TX Descriptors faster.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb should be freed by dev_consume_skb_any() in efx_tx_tso_fallback()
when skb is still used. The skb will be replaced by segments, so the
original skb should be consumed(not drop).
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb should be freed by dev_consume_skb_any() in macb_pad_and_fcs()
when *skb is still used. The *skb is be replaced by nskb, so the
original *skb should be consumed(not drop).
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit
done.It makes drop profiles more friendly.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
modify the code style in order to removing the following warning
when excute the script checkpatch.pl
WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in w90p910_ether_start_xmit()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in ks8695_tx_irq() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in myri10ge_tx_done() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in intr_handler() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Remove a redundant blank line in intr_handler().
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow thermal zone binding to an external cooling device from the
cooling devices white list.
It provides support for Mellanox next generation systems on which
cooling device logic is not controlled through the switch registers.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add label attribute to hwmon object for exposing QSFP module's
temperature sensor name. Modules are labeled as "front panel xxx". The
label is used by utilities such as "sensors":
front panel 001: +0.0C (crit = +0.0C, emerg = +0.0C)
..
front panel 020: +31.0C (crit = +70.0C, emerg = +80.0C)
..
front panel 056: +41.0C (crit = +70.0C, emerg = +80.0C)
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new attributes to hwmon object for exposing QSFP module temperature
input, fault indication, critical and emergency thresholds. Temperature
input and fault indication are read from Management Temperature Bulk
Register. Temperature thresholds are read from Management Cable Info
Access Register.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fan hwmon attribute for exposing fan faults (fault indication is
read from Fan Out of Range Event Register).
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename cooling device from "Fan" to "mlxsw_fan". Name "Fan" is too
common name, and such name is misleading, while it's interpreted by
user. For example name "Fan" could be used by ACPI.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace thermal hardcoded temperature trip values with defines.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify thermal zone trip points setting for better alignment with system
thermal requirement.
Add hysteresis thresholds for thermal trips in order to avoid throttling
around thermal trip point. If hysteresis temperature is not considered,
PWM can have side effect of flip up/down on thermal trip point boundary.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add low frequency bus capability in order to allow core functionality
separation based on bus type. Driver could run over PCIe, which is
considered as high frequency bus or I2C, which is considered as low
frequency bus. In the last case time setting, for example, for thermal
polling interval, should be increased.
Use different thermal monitoring based on bus type. For I2C bus time is
set to 20 seconds, while for PCIe 1 second polling interval is used.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new API to read QSFP module's temperature thresholds - warning and
critical.
New internal API reads the temperature thresholds from the modules,
which are equipped with the thermal sensor. These thresholds will be
exposed via hwmon subsystem.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FORE (Fan Out of Range Event Register), which is used for fan fault
reading.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MTBR (Management Temperature Bulk Register), which is used for port
temperature reading in a bulk mode.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move QSFP EEPROM definitions to common location from the spectrum driver
in order to make them available for other mlxsw modules. They are common
for all kind of chips and have relation to SFF specifications 8024,
8436, 8472, 8636, rather than to chip type.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CR4_QSFP 10G Speed technology should be 10000baseKR_Full
And also report available FEC modes.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some statements in an if-block that are not correctly
indented. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in eth_txdone_irq() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in at91ether_interrupt() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in intr_handler() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in moxart_tx_finished() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in mace_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in emac_mac_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5 driver creates xdp redirect hw queues unconditionally on
netdevice open, This is great until someone starts redirecting XDP traffic
via ndo_xdp_xmit on mlx5 device and changes the device configuration at
the same time, this might cause crashes, since the other device's napi
is not aware of the mlx5 state change (resources un-availability).
To fix this we must synchronize with other devices napi's on the system.
Added a new flag under mlx5e_priv to determine XDP TX resources are
available, set/clear it up when necessary and use synchronize_rcu()
when the flag is turned off, so other napi's are in-sync with it, before
we actually cleanup the hw resources.
The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and
it is sufficient to determine if it safe to transmit or not. The other
two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become
unnecessary. Thus, they are removed from data path.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eliminate the following compilation warning:
drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]: => 238:3
Fixes: c2fb3db22d ("net/mlx5: Rework handling of port module events")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When EEH is injected and PCI bus stalls, mlx5's pci error detect
function is called to deactivate the command interface and tear down
the device. The issue is that there can be a thread that already
passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command
and stuck in the wait_func.
Solution:
Add function mlx5_cmd_flush to disable command interface and clear all
the pending commands. When device state is set to
MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all
pending threads waiting for firmware commands completion are terminated.
Fixes: c1d4d2e92a ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New channels are applied to the priv channels only after they
are successfully opened. Then, the indirection table should be built
according to the new number of channels.
Currently, such build is preformed independently of whether the
channels opening is successful, and is not reverted on failure.
The bug is caused due to removal of rss params from channels struct
and moving it to priv struct. That change cause to independency between
channels and rss params.
This causes a crash on a later point, when accessing rqn of a non
existing channel.
This patch fixes it by moving the indirection table build right before
switching the priv channels to new channels struct, after the new set of
channels was successfully opened.
Fixes: bbeb53b8b2 ("net/mlx5e: Move RSS params to a dedicated struct")
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update newly introduced function to be aligned to netdev coding style.
Fixes: 46861e3e88 ("net/mlx5: Set ODP SRQ support in firmware")
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
After 1ecb195753 ("mlxsw: spectrum_switchdev: Remove getting
PORT_BRIDGE_FLAGS") we are not accessing any driver private data
structure, so the mlxsw_sp_port and mlxsw_sp variables are unused.
Fixes: 1ecb195753 ("mlxsw: spectrum_switchdev: Remove getting PORT_BRIDGE_FLAGS")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 610d2b601b ("rocker: Remove getting PORT_BRIDGE_FLAGS") we no
longer have a port_attr_bridge_flags_get member in the rocker_world_ops
structre, fix that.
Fixes: 610d2b601b ("rocker: Remove getting PORT_BRIDGE_FLAGS")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix race condition between ena_update_on_link_change() and
ena_restore_device().
This race can occur if link notification arrives while the driver
is performing a reset sequence. In this case link can be set up,
enabling the device, before it is fully restored. If packets are
sent at this time, the driver might access uninitialized data
structures, causing kernel crash.
Move the clearing of ENA_FLAG_ONGOING_RESET and netif_carrier_on()
after ena_up() to ensure the device is ready when link is set up.
Fixes: d18e4f6834 ("net: ena: fix race condition between device reset and link up setup")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, it is not guaranteed. For example, switches might
choose to make other use of these octets.
This repeatedly causes kernel hardware checksum fault.
Prior to the cited commit below, skb checksum was forced to be
CHECKSUM_NONE when padding is detected. After it, we need to keep
skb->csum updated. However, fixing up CHECKSUM_COMPLETE requires to
verify and parse IP headers, it does not worth the effort as the packets
are so small that CHECKSUM_COMPLETE has no significant advantage.
Future work: when reporting checksum complete is not an option for
IP non-TCP/UDP packets, we can actually fallback to report checksum
unnecessary, by looking at cqe IPOK bit.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add PTP clock driver for ENETC.
The driver reused QorIQ PTP clock driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Strings containing "ptp_qoriq" or "qoriq_ptp" which were used for
structure/function names were complained by users. Let's just use
the unique "ptp_qoriq" to make these names more consistent.
This patch is just to unify the names using "ptp_qoriq". It hasn't
changed any functions.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no code that attempts to get the
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS attribute, remove support for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no code that will query the SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
attribute remove support for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places which make the decision whether to access the
XLGMAC vs GMAC that only check for PHY_INTERFACE_MODE_10GKR and not its
XAUI variant. Switch these to use the new helper so that we have
consistency through the driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mvpp2_is_xlg() helper to identify whether the interface mode
should be using the XLGMAC rather than the GMAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, it is not guaranteed. For example, switches might
choose to make other use of these octets.
This repeatedly causes kernel hardware checksum fault.
Prior to the cited commit below, skb checksum was forced to be
CHECKSUM_NONE when padding is detected. After it, we need to keep
skb->csum updated. However, fixing up CHECKSUM_COMPLETE requires to
verify and parse IP headers, it does not worth the effort as the packets
are so small that CHECKSUM_COMPLETE has no significant advantage.
Future work: when reporting checksum complete is not an option for
IP non-TCP/UDP packets, we can actually fallback to report checksum
unnecessary, by looking at cqe IPOK bit.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b639583f9e.
As per discussion with Jakub Kicinski and Michal Kubecek,
this will be better addressed by soon-too-come ethtool netlink
API with additional indication that given configuration request
is supposed to be persisted.
Also, remove the parameter support from bnxt_en driver.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Michal Kubecek <mkubecek@suse.cz>
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Note that smc911x apparently is a PIO chip with an external DMA
handshake, and we probably use the wrong device here. But at least
it matches the mapping side, which apparently works or at least
worked in the not too distant past.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Also use GFP_KERNEL instead of GFP_ATOMIC as the gfp_t for the memory
allocation, as we aren't in interrupt context or under a lock.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Note that this driver seems to entirely lack dma_map_single error
handling, but that is left for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Note this driver seems to lack dma_unmap_* calls entirely, but fixing
that is left for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not support VLAN push and pop, but only VLAN modify.
Fixes: 7386788175 ("drivers: net: use flow action infrastructure")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the register access failed an error would be logged anyway, so
we can drop the warning.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAG port collecting (receive) function was mistakenly set when the
port was registered as a LAG member, while it should be set only when
the port collection state is set to true. Set LAG port to collecting
when it is set to distributing, as described in the IEEE link
aggregation standard coupled control mux machine state diagram.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.
Fixes: 3366463513 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent cls_flower offload rewrite added a double new line.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently bpf_offload_dev does not have any priv pointer, forcing
the drivers to work backwards from the netdev in program metadata.
This is not great given programs are conceptually associated with
the offload device, and it means one or two unnecessary deferences.
Add a priv pointer to bpf_offload_dev.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The manufacturing team requests we include vendor and product
in the serial number field, as the serial number itself is not
unique across manufacturing facilities and products.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vendor may sound ambiguous, let's rename the fab string to
"board.manufacture" (which was just added as a generic identifier).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_eq_cq_get() is called in IRQ handler, the spinlock inside
gets a lot of contentions when we test some heavy workload
with 60 RX queues and 80 CPU's, and it is clearly shown in the
flame graph.
In fact, radix_tree_lookup() is perfectly fine with RCU read lock,
we don't have to take a spinlock on this hot path. This is pretty
much similar to commit 291c566a28
("net/mlx4_core: Fix racy CQ (Completion Queue) free"). Slow paths
are still serialized with the spinlock, and with synchronize_irq()
it should be safe to just move the fast path to RCU read lock.
This patch itself reduces the latency by about 50% for our memcached
workload on a 4.14 kernel we test. In upstream, as pointed out by Saeed,
this spinlock gets some rework in commit 02d92f7903
("net/mlx5: CQ Database per EQ"), so the difference could be smaller.
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit 2e6eedb481.
Sander reported a regression causing a kernel panic[1],
therefore let's revert this commit.
[1] https://marc.info/?t=154965066400001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bd7153bd83.
There doesn't seem to be anything wrong with this patch,
it's just reverted to get a stable baseline again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mvpp2 configures the flow control modes in mvpp2_xlg_config() for
10G mode, it only ever set the flow control enable bits. There is no
mechanism to clear these bits, which means that userspace is unable to
use standard APIs to disable flow control (the only way is to poke the
register directly.)
Fix the missing bit clearance to allow flow control to be disabled.
This means that, by default, as there is no negotiation in 10G modes
with mvpp2, flow control is now disabled rather than being rx-only.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink already limits which interface modes are able to call the
MACs AN restart function, but in any case, the commentry seems
incorrect: the AN restart bit does not automatically clear when
set. This has been found via manual setting using devmem2, and
we can observe that the AN does indeed restart and complete, yet
the AN restart bit remains set. Explicitly clear the AN restart
bit.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading the pause bits in mac_link_state, mvpp2 was reporting
the state of the "active pause" bits, which are set when the MAC is
in pause mode. This is not what phylink wants - we want the
negotiated pause state. Fix the definition so we read the correct
bits.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_config() can be called at any point, and the expected behaviour
from MAC drivers is to only reprogram when necessary - and certainly
avoid taking the link down on every call.
Unfortunately, mvpp2 does exactly that - it takes the link down, and
reprograms everything, and then releases the forced-link down.
This is bad, it can cause the link to bounce:
- SFP detects signal, disables LOS indication.
- SFP code calls into phylink, calling phylink_sfp_link_up() which
triggers a resolve.
- phylink_resolve() calls phylink_get_mac_state() and finds the MAC
reporting link up.
- phylink wants to configure the pause mode on the MAC, so calls
phylink_mac_config()
- mvpp2 takes the link down temporarily, generating a MAC link down
event followed by another MAC link event.
- phylink calls mac_link_up() and then processes the MAC link down
event.
- phylink_resolve() gets called again, registers the link down, and
calls mach_link_down() before re-running itself.
- phylink_resolve() starts again at step 3 above. This sequence
repeats.
GMAC versions prior to mvpp2 do not require the link to be taken down
except when certain link properties (eg, switching between SGMII and
1000base-X mode, or enabling/disabling in-band negotiation) are
changed. Implement this for mvpp2.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that the mvpp22 can get stuck with SGMII negotiation. The
symptoms are that in-band negotiation never completes and the partner
(eg, PHY) never reports SGMII link up, or if it supports negotiation
bypass, goes into negotiation bypass mode (which will happen when the
PHY sees that the MAC is alive but gets no response.)
Triggering the PHY end of the link to re-negotiate results in the
bypass bit clearing on the PHY, and then re-setting - indicating that
the problem is at the mvpp22 GMAC end.
Asserting the GMAC reset and de-asserting it resolves the issue.
Arrange to assert the GMAC reset at probe time, and deassert it only
after we have configured the GMAC for the appropriate mode. This
resolves the issue.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Auhagen reported issues with negotiation on a couple of his
platforms using a mixture of SFP and PHYs in various different
modes. Debugging to root cause proved difficult, but essentially
the problem comes down to the mvpp2 phylink implementation being
slightly at odds with what is expected.
phylink operates in three modes: phy, fixed-link, and in-band mode.
In the first two modes, the expected behaviour from a MAC driver is
that phylink resolves the operating mode and passes the mode to the
MAC driver for it to program, including when the link should be
brought up or taken down. This is basically the same as the libphy
approach. This does not negate the requirement to advertise a correct
control word for interface modes that have control words where that
can be reasonably controlled.
The second mode is in-band mode, where the MAC is expected to use the
in-band control word to determine the operating mode.
The mvneta driver implements the correct pattern required to support
this: configure the port interface type separately from the in-band
mode(s). This is now specified in the phylink documentation patches.
mvpp2 was programming in-band mode for SGMII and the 802.3z modes no
what, and avoided forcing the link up in fixed/phy modes. This caused
a problem with some boards where the PHY is by default programmed to
enter AN bypass mode, the PHY would report that the link was up, but
the mvpp2 never completed the exchange of control word.
Another issue that mvpp2 has is it sets SGMII AN format control word
for both SGMII and 802.3z modes. The format of the control word is
defined by MVPP2_GMAC_INBAND_AN_MASK, which should be set for SGMII
and clear for 802.3z. Available Marvell documentation for earlier
GMAC implementations does not make this clear, but this has been
ascertained via extensive testing on earlier GMAC implementations,
and then confirmed with a Macchiatobin Single Shot connected to a
Clearfog: when MVPP2_GMAC_INBAND_AN_MASK is set, the clearfog does
not receive the advertised pause mode settings.
Lastly, there is no flow control in the in-band control word in Cisco
SGMII, setting the flow control autonegotiation bit even with a PHY
that has the Marvell extension to send this information does not result
in the flow control being enabled at the MAC. We need to do this
manually using the information provided via phylink.
Re-code mvpp2's mac_config() and mac_link_up() to follow this pattern.
This allows Sven Auhagen's board and Macchiatobin to reliably bring
the link up with the 88e1512 PHY with phylink operating in PHY mode
with COMPHY built as a module but the rest of the networking built-in,
and u-boot having brought up the interface. in-band mode requires an
additional patch to resolve another problem.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
size = sizeof(struct foo) + count * sizeof(void *);
instance = alloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable alloc_size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable fsz is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support to query SmartAN capability via ethtool.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver interface to read the SmartAN capability from
management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new compatibility string for this product. It's using
at91sam9260-macb layout but has a newer hardware revision: it's safer
to use its own string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
