Never used, remove it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller is able to support 2.5G speeds, allowing to use
2.5GBASET in conjunction with PHYs that use 2500BASEX as their MII
interface when using this mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is no longer necessary after a5084bb71f ("nfp: Implement
ndo_get_port_parent_id()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_change_mtu() is not needed any more, the networking subsystem will
call it automatically when this callback is not implemented.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccGvRAAoJEEg/ir3gV/o+6kIH/1Y23h0OZrKkkfELujtzoOjx
64BIRhW8Tr+WOXZNKlSvdRkPj0g1yG3B0NO7wChXZDl8dgqBp/Jx5Wxcvb5DKkz/
wK07oKB6KqgcMILzUe5G4iOHw/atMldzSA6sNPh8SDKVKKkXjMKz8ocQZZQRsAaX
1im2D77pX8zE/OhG86Fn23Fed1G6Lg++faPC8GEOxv9LkwaAARa5NfJ6g7AnXOGg
ijmM4R2Hhu0V0YaKXS2qJFb6HQaNO9JKYR1C7wF7z9yqnsn14cdxrAWkE4eA2JnP
zKnDt+ThAKAoX9mn5QHzD8uye56Jeksvo8br4dCH4iDZZSSZT+lo456Dfe+tXpc=
=ef79
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-02-21
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Spectrum-2 ASIC support for the following new port types and speeds:
* 50Gbps 1-lane
* 100Gbps 2-lanes
* 200Gbps 4-lanes
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Spectrum-2 ASIC port type-speed operations.
Since multiple ethtool link modes are represented using a single bit in the
ASIC, the driver forces the user to configure all types per a specific
speed. For example, if the user wants to advertise 100Gbps 4-lanes speed,
he should advertise all the types of 100Gbps 4-lanes speed that are
supported by the ASIC as shown below:
Supported ethtool bits for 100Gbps 4-lanes:
0x1000000000 100000baseKR4 Full
0x2000000000 100000baseSR4 Full
0x4000000000 100000baseCR4 Full
0x8000000000 100000baseLR4_ER4 Full
Command for advertising 100Gbps 4-lanes:
ethtool -s enp3s0np1 advertise 0xF000000000
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTYS register introduces a new layout for port type-speed fields. These
fields extend the existing ones in order to handle more types and speeds.
For example, the new 200Gbps speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename p_eth_proto_adm to p_eth_proto_admin in mlxsw_reg_ptys_eth_unpack
function.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port type-speed operations in order to have different operations for
different ASICs. For now, both ASICs use the same pointer.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename port speed-type functions to be Spectrum-1 ASIC specific.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of deriving the port connector type from port admin state, query it
from firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove eth_proto_lp_advertise field in PTYS register since it is not
supported by the firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate port link mode entry from mlxsw_sp_port_link_mode.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_prio_stats[i].str, prio);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_tc_stats[i].str, tc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The intended optimization should be A ^ 0 = A, not A ^ -1 = A.
Fixes: cd7df56ed3 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Allow enabling VEPA mode on the HCA's port in legacy devlink mode.
Example:
bridge link set dev ens1f0 hwmode vepa
will turn on VEPA mode on the netdev ens1f0.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In Virtual Ethernet Port Aggregator (VEPA) mode, the packet skips
the system internal virtual switch and forwards to external network
switch. In Mellanox HCA case, the virtual switch is the HCA's Eswitch.
To support this, an new FDB flow table are created with level 0 and
linked to the existing FDB flow table in legacy mode. By default,
VEPA is turned off and this FDB flow table is empty. When VEPA is
turned on, two rules are created. One rule to forward on uplink vport
traffic to the legacy FDB. The other rule forward all other traffic
to uplink vport.
Other design alternatives were not chosen as explained below:
1. Create a forward rule in ACL flow table (most efficient design).
This approach is the not chosen because firmware does not support
forward rule to uplink vport (0xffff) for ACL flow table.
2. Add additional source port criteria in all the FDB rules to make the
FDB rules to be received rules only. This approach is not chosen because
it is not efficient as there can many rules in the FDB and VEPA mode
cannot be controlled per vport.
3. Add a highest prioirty flow group in the existing legacy FDB Flow
Table instead of a new flow table. This approoach does not work because the
new flow group has the same match criteria as the promiscuous flow group
and mlx5_add_flow_rules does not allow specifying flow group.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If reporter is ERR_PTR or NULL, error code shall be returned. At all other
cases it shall return success. Fix that.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case of lost interrupt recover, we shall return success. Fix that.
Fixes: 7d91126b1a ("net/mlx5e: Add tx timeout support for mlx5e tx reporter")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When TX reporter was introduced, it took ownership over TX timeout error
handling. this introduced a regression in case TX reporter is not valid
(NET_DEVLINK is not set, or devlink_health_reporter_create failure).
Fix mlx5e_tx_reporter_timeout function so it can be called at all times.
In addition, remove a warning print that indicates that a TX timeout won't
be handled in case of no valid TX reporter.
Fixes: 7d91126b1a ("net/mlx5e: Add tx timeout support for mlx5e tx reporter")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Print warning message in case of TX reporter creation failure, only if the
return value is ERR_PTR type. NULL pointer return indicates that
NET_DEVLINK is not set, and the warning print can be skipped.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bff1 ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.
Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).
Fixes: df2ef3bff1 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently changing a PCMR field is done by setting the field in a
zeroed buffer, zeroing other unrelated fields.
Fix this behaviour by modifying only the required field after first
reading the current register values, as a pre-step towards using more
fields in PCMR register.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After AF_PACKET is fixed to calculate the transport header offset
correctly, trust the value set by the kernel. If the offset wasn't set,
it means there is no transport header in the packet.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_transport_offset() == 0 is not a special value. The only special
value is when skb->transport_header is ~0U, and it's checked by
skb_transport_header_was_set().
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To communicate to PF each of ThunderX NIC VF uses mailbox which is
pair of 64 bit registers available to both VFn and PF.
This commit is to change the xcast message structure in order to
fit it into 64 bit.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct STREERING to STEERING at macro name for BGX steering register.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three smallish patches fixing regressions in v5.0:
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset
-----BEGIN PGP SIGNATURE-----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=JFU9
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Small set of three regression fixing patches, things are looking
pretty good here.
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
iw_cxgb4: cq/qp mask depends on bar2 pages in a host page
cxgb4: Export sge_host_page_size to ulds
RDMA/srp: Rework SCSI device reset handling
A missing break keyword should have been added after adding support for
PRE_BRIDGE_FLAGS.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 93700458ff ("rocker: Check Handle PORT_PRE_BRIDGE_FLAGS")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading VF driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Also this patch adds hclge_cmd_uninit() to do the command queue
uninitialization which includes clearing registers and freeing
memory.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify print message of 6th bit of ppp mpf abnormal errors,
there is a extra letter e in it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
