The integer exponentiation is used in few places and might be used in
the future by other call sites. Move it to wider use.
Link: http://lkml.kernel.org/r/20190323172531.80025-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add fwnode support to the lm3630a driver and optionally allow
configuring the label, default brightness level, and maximum brightness
level. The two outputs can be controlled by bank A and B independently
or bank A can control both outputs.
If the platform data was not configured, then the driver defaults to
enabling both banks. This patch changes the default value to disable
both banks before parsing the firmware node so that just a single bank
can be enabled if desired. There are no in-tree users of this driver.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status()
both return the brightness value if the brightness was successfully
updated. Writing to these attributes via sysfs would cause a 'Bad
address' error to be returned. These functions should return 0 on
success, so let's change it to correct that error.
Fixes: 28e64a68a2 ("backlight: lm3630: apply chip revision")
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch removes dependencies on BACKLIGHT_CLASS_DEVICE for items
that are already placed under 'if BACKLIGHT_CLASS_DEVICE'.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We have two *_CLASS_DEVICE kernel config options (LCD_CLASS_DEVICE
and BACKLIGHT_LCD_DEVICE) that do the same job.
The patch removes useless BACKLIGHT_LCD_SUPPORT option
and converts LCD_CLASS_DEVICE into a menu.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
gpiod_get_value() gives out a warning if access to the underlying gpiochip
requires sleeping, which is common for I2C based chips:
WARNING: CPU: 0 PID: 77 at drivers/gpio/gpiolib.c:2500 gpiod_get_value+0xd0/0x100
Modules linked in:
CPU: 0 PID: 77 Comm: kworker/0:2 Not tainted 4.14.0-rc3-00589-gf32897915d48-dirty #90
Hardware name: Allwinner sun4i/sun5i Families
Workqueue: events deferred_probe_work_func
[<c010ec50>] (unwind_backtrace) from [<c010b784>] (show_stack+0x10/0x14)
[<c010b784>] (show_stack) from [<c0797224>] (dump_stack+0x88/0x9c)
[<c0797224>] (dump_stack) from [<c0125b08>] (__warn+0xe8/0x100)
[<c0125b08>] (__warn) from [<c0125bd0>] (warn_slowpath_null+0x20/0x28)
[<c0125bd0>] (warn_slowpath_null) from [<c037069c>] (gpiod_get_value+0xd0/0x100)
[<c037069c>] (gpiod_get_value) from [<c03778d0>] (pwm_backlight_probe+0x238/0x508)
[<c03778d0>] (pwm_backlight_probe) from [<c0411a2c>] (platform_drv_probe+0x50/0xac)
[<c0411a2c>] (platform_drv_probe) from [<c0410224>] (driver_probe_device+0x238/0x2e8)
[<c0410224>] (driver_probe_device) from [<c040e820>] (bus_for_each_drv+0x44/0x94)
[<c040e820>] (bus_for_each_drv) from [<c040ff0c>] (__device_attach+0xb0/0x114)
[<c040ff0c>] (__device_attach) from [<c040f4f8>] (bus_probe_device+0x84/0x8c)
[<c040f4f8>] (bus_probe_device) from [<c040f944>] (deferred_probe_work_func+0x50/0x14c)
[<c040f944>] (deferred_probe_work_func) from [<c013be84>] (process_one_work+0x1ec/0x414)
[<c013be84>] (process_one_work) from [<c013ce5c>] (worker_thread+0x2b0/0x5a0)
[<c013ce5c>] (worker_thread) from [<c0141908>] (kthread+0x14c/0x154)
[<c0141908>] (kthread) from [<c0107ab0>] (ret_from_fork+0x14/0x24)
This was missed in commit 0c9501f823 ("backlight: pwm_bl: Handle gpio
that can sleep"). The code was then moved to a separate function in
commit 7613c92231 ("backlight: pwm_bl: Move the checks for initial power
state to a separate function").
The only usage of gpiod_get_value() is during the probe stage, which is
safe to sleep in. Switch to gpiod_get_value_cansleep().
Fixes: 0c9501f823 ("backlight: pwm_bl: Handle gpio that can sleep")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which this is.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit '88ba95bedb79 ("backlight: pwm_bl: Compute brightness of LED
linearly to human eye")' allows the possibility to compute a default
brightness table when there isn't the brightness-levels property in the
DT. Unfortunately the changes made broke the pwm backlight for the
non-DT boards.
Usually, the non-DT boards don't pass the brightness levels via platform
data, instead, it sets the max_brightness in their platform data and the
driver calculates the level without a table. The offending patch assumed
that when there is no brightness levels table we should create one, but this
is clearly wrong for the non-DT case.
After this patch the code handles the DT and the non-DT case taking in
consideration also if max_brightness is set or not.
Fixes: 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly to human eye")
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly
to human eye") made the parse-dt function return early when using an auto-
generated brightness-table, but didn't take into account that some more
settings were handled below the brightness handling, like power-on-delays
and also setting the pdata enable-gpio to -EINVAL.
This surfaces for example in the case of a backlight without any
enable-gpio which then tries to use gpio-0 in error.
Fix this by simply moving the trailing settings above the brightness
handling.
Fixes: 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly to human eye")
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit e6bcca0890 ("backlight: pwm_bl: Switch to using "atomic" PWM API")
removed the driver internal enabled tracking in favor of simply checking
the pwm state.
This can lead to issues as all of gpio-, regulator- and pwm-state are used
to determine the initial state and the bootloader or kernel can leave them
in an inconsistent state at boot.
In my case on rk3399-kevin, the pwm backlight is build as module and the
kernel disables the supply regulator as unused while keeping the pwm running
thus pwm_bl calling pwm_backlight_power_off() during probe and creating an
unmatched regulator-disable call, as it never got enabled from the pwm-bl
before.
To prevent these consistency issues, reintroduce the driver-internal
tracking of the enabled state.
Fixes: e6bcca0890 ("backlight: pwm_bl: Switch to using "atomic" PWM API")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----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=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
The driver for LD9040 AMOLED LCD panel was superseded with DRM driver
panel-samsung-ld9040.c. It does not support DeviceTree and respective
possible user (Exynos4210 Universal C210) is DeviceTree-only and uses
DRM version of driver.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver for S6E63M0 AMOLED LCD panel is not used. It does not
support DeviceTree and respective possible users (S5Pv210 Aquila and
Goni boards) are DeviceTree-only.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/video/backlight/lm3639_bl.c:403:14: warning: address of
'pchip->cdev_torch' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_torch)
~~ ~~~~~~~^~~~~~~~~~
drivers/video/backlight/lm3639_bl.c:405:14: warning: address of
'pchip->cdev_flash' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_flash)
~~ ~~~~~~~^~~~~~~~~~
2 warnings generated.
These statements have been present since 2012, introduced by
commit 0f59858d51 ("backlight: add new lm3639 backlight
driver"). Given that they have been called unconditionally since
then presumably without any issues, removing the always true if
statements to fix the warnings without any real world changes.
Link: https://github.com/ClangBuiltLinux/linux/issues/119
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The "atomic" API allows us to configure PWM period and duty_cycle and
enable it in one call.
The patch also moves the pwm_init_state just before any use of the
pwm_state struct, this fixes a potential bug where pwm_get_state
can be called before pwm_init_state.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No functional changes
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, if the DT does not define num-interpolated-steps then
num_steps is undefined and the interpolation code will deploy randomly.
Fix with a simple initialize to zero.
Fixes: 573fe6d1c2 ("backlight: pwm_bl: Linear interpolation between brightness-levels")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When you want to change the brightness using a PWM signal, one thing you
need to consider is how human perceive the brightness. Human perceive
the brightness change non-linearly, we have better sensitivity at low
luminance than high luminance, so to achieve perceived linear dimming,
the brightness must be matches to the way our eyes behave. The CIE 1931
lightness formula is what actually describes how we perceive light.
This patch computes a default table with the brightness levels filled
with the numbers provided by the CIE 1931 algorithm, the number of the
brightness levels is calculated based on the PWM resolution.
The calculation of the table using the CIE 1931 algorithm is enabled by
default when you do not define the 'brightness-levels' propriety in your
device tree.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setting num-interpolated-steps in the dts will allow you to have linear
interpolation between values of brightness-levels. This way a high
resolution pwm duty cycle can be used without having to list out every
possible value in the dts. This system also allows for gamma corrected
values.
The most simple example is interpolate between two brightness values a
number of steps, this can be done setting the following in the dts:
brightness-levels = <0 65535>;
num-interpolated-steps = <1024>;
default-brightness-level = <512>;
This will create a brightness-level table with the following values:
<0 63 126 189 252 315 378 441 ... 64260 64323 64386 64449 65535>
Another use case can be describe a gamma corrected curve, as we have
better sensitivity at low luminance than high luminance we probably
want have smaller steps for low brightness levels values and bigger
steps for high brightness levels values. This can be achieved with
the following in the dts:
brightness-levels = <0 4096 65535>;
num-interpolated-steps = <1024>;
default-brightness-level = <512>;
This will create a brightness-levels table with the following values:
<0 4 8 12 16 20 ... 4096 4156 4216 4276 ... 65535>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Two framebuffer device-node names were looked up during probe, but were
only used as flags to indicate the presence of two framebuffer device.
Drop the unused framebuffer name along with a likewise unused device
pointer from the driver data, and update the platform data to pass in
booleans instead of the framebuffer strings. This allows us do drop the
node references acquired during probe, which would otherwise leak.
Note that there are no other in-kernel users of the modified
platform-data fields.
Fixes: 59eb2b5e57 ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.
Cc: stable <stable@vger.kernel.org> # 3.7
Fixes: eebfdc17cc ("backlight: Add TPS65217 WLED driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.
Cc: stable <stable@vger.kernel.org> # 3.9
Fixes: 47ec340cb8 ("mfd: max8925: Support dt for backlight")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed.
Cc: stable <stable@vger.kernel.org> # 3.10
Fixes: 59eb2b5e57 ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Leaking driver internal tracking into the already massively confusing
backlight power tracking is really confusing.
Stop that by allocating a tiny driver private data structure instead.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nothing in the entire tree ever sets this, which means this is dead
code. Remove it.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a LCD driver supporting the OTM3225A LCD SoC
from ORISE Technology. This device can drive TFT LC panels having a
resolution of 240x320 pixels. After initializing the OTM3225A using
it's SPI interface it switches to use 16-bib RGB as external
display interface.
Signed-off-by: Felix Brack <fb@ltec.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation was wrong, gpiod_get_direction() returns 0/1 instead
of the GPIOF_* flags. The docs were fixed with commit 94fc73094a
("gpio: correct docs about return value of gpiod_get_direction"). Now,
fix this user (until a better, system-wide solution is in place).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some panels (i.e. N116BGE-L41), in their power sequence specifications,
request a delay between set the PWM signal and enable the backlight and
between clear the PWM signal and disable the backlight. Add support for
the new post-pwm-on-delay-ms and pwm-off-delay-ms proprieties to meet
the timings.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Before this patch the enable signal was set before the PWM signal and
vice-versa on power off. This sequence is wrong, at least, it is on
the different panels datasheets that I checked, so I inverted the sequence
to follow the specs.
For reference the following panels have the mentioned sequence:
- N133HSE-EA1 (Innolux)
- N116BGE (Innolux)
- N156BGE-L21 (Innolux)
- B101EAN0 (Auo)
- B101AW03 (Auo)
- LTN101NT05 (Samsung)
- CLAA101WA01A (Chunghwa)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver provides access to RAVE SP backlight control
functionality.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
migrate the backlight helpers from tinydrm to the backlight subsystem.
https://patchwork.freedesktop.org/series/36522/
Cc: Meghana Madhyastha <meghana.madhyastha@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlpvdTQACgkQlvcN/ahK
Bwp5Pgf8Cfn7p7/HV5npF0b0NZ3w0FLF+AjggxKdKBNsVYdO1qGrhfQJviuMRj7c
cqm+SQ4OFJEwGMqVGsZLgRkyVrbCma/OZEcipJiSGHLG9owDgVFYTQ4bnakmdt1m
QYJTETNxoNJ1EHCG1tfr9/jDR3GPL3OnSUOWnlTXDzpJ2PCw4BB0uArqG+pgmyhJ
DCMdvYkQ+5tYB814otnN3zklklQITNGww8LTJMtDFyJVIz2RZHioq5JqXD48UfMb
haDVbiYsOamw+eP4z5uyfCi1rKwzpPhas9IpeDn5gY6rEp/t+GTkSr0JHUEs/iB+
+eAH076eTp3M8iv7YF67XYLZQeDuwQ==
=azAl
-----END PGP SIGNATURE-----
Merge tag 'topic/backlight_for_lag-2018-01-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-misc-next
This contains the backlight portion of Meghana Madhyastha's patch set to
migrate the backlight helpers from tinydrm to the backlight subsystem.
https://patchwork.freedesktop.org/series/36522/
Cc: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
# gpg: Signature made Mon 29 Jan 2018 02:25:40 PM EST
# gpg: using RSA key 7F17297CC4A076740CB3E42A96F70DFDA84A070A
# gpg: Good signature from "Sean Paul <seanpaul@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1C5E AB9E D7C9 DDE9 E7F2 087C 732C 0025 72DC AF79
# Subkey fingerprint: 7F17 297C C4A0 7674 0CB3 E42A 96F7 0DFD A84A 070A
Link: https://patchwork.freedesktop.org/patch/msgid/20180129192950.bvmhkz3h42t5a25r@art_vandelay
Add devm_of_find_backlight and the corresponding release
function because some drivers use devres versions of functions
for acquiring device resources.
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/021f8fecfa3f374dc5dcb70fb07a6f6b019bea7b.1516810725.git.meghana.madhyastha@gmail.com
Add of_find_backlight, a helper function which is a generic version
of tinydrm_of_find_backlight that can be used by other drivers to avoid
repetition of code and simplify things.
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/116d160ba78be2e6dcbdcb6855622bce67da9472.1516810725.git.meghana.madhyastha@gmail.com
Currently the LCD display (TD035S) on the cm-x300 platform is broken and
remains blank.
The TD0245S specification requires that the chipselect is toggled
between commands sent to the panel. This was also the purpose of the
former patch of commit f64dcac0b1 ("backlight: tdo24m: ensure chip
select changes between transfers").
Unfortunately, the "cs_change" field of a SPI transfer is
misleading. Its true meaning is that for a SPI message holding multiple
transfers, the chip select is toggled between each transfer, but for the
last transfer it remains asserted.
In this driver, all the SPI messages contain exactly one transfer, which
means that each transfer is the last of its message, and as a
consequence the chip select is never toggled.
Actually, there was a second bug hidding the first one, hence the
problem was not seen until v4.6. This problem was fixed by commit
a52db659c7 ("spi: pxa2xx: Fix cs_change management") for PXA based
boards.
This fix makes the TD035S work again on a cm-x300 board. The same
applies to other PXA boards, ie. corgi and tosa.
Fixes: a52db659c7 ("spi: pxa2xx: Fix cs_change management")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Hard-coding the domain as 0.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The variable len is assigned but never read, therefore it is redundant
and can be removed. Cleans up clang warning:
drivers/video/backlight/ili922x.c:276:2: warning: Value stored to 'len'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Variable val holds the default brightness and is unsigned, therefore
checking whether it is less than zero is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes an overflow condition that can happen with high max
brightness and period values in compute_duty_cycle. This fixes it by
using a 64 bit variable for computing the duty cycle.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>